Bennett 3000 Series Mechanical

Commercial and Retail Dispensers

Installation & Operator’s Manual

Only Trained Personnel May Work on This Equipment
Includes Instructions For:
Model 3100 Commercial Mechanical 101 (Volume Only)
Non-computer with Electric Reset

Model 3200 Commercial Mechanical, 101 (Volume Only)

Non-Computer & Cam AC Reset

Model 3300 Retail Mechanical (Money & Volume), V/R

10/4 & Electric Reset

Model 3400 Retail Mechanical (Money & Volume),

V/R 10/4 & Cam AC

Model 3500 Retail Mechanical (Money & Volume),

V/R 10 & Electric Reset

Model 3600 Retail Mechanical (Money & Volume),

V/R 10 & Cam AC

Remote Dispensers
and
Self-Contained Pumps

READ THIS MANUAL

This manual has important information for safe installation and
operation of this equipment. Read and understand this manual
before applying power. Keep this manual and tell all service
personnel to read this manual. If you do not follow the
instructions, you can cause bodily injury, death or damage to the
equipment.
For new manuals, FAX to:
BENNETT MARKETING SERVICES
(231)799-6202
or visit our web page at:
http://www.bennettpump.com

107929 Rev E 04-24-17

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456

USA 800-235-7618 ~ Outside USA 231-798-1310
sales@bennettpump.com ~ www.bennettpump.com
 Table of Contents
Safety Instructions 3
Introduction for the 3000 series Mechanical Commercial and Retail Dispensers 4
Product Specifications 6
Determining the Model Number 7
Dispenser Identification Number Summary (DIN) 8
Unloading, Unpacking and Inspecting a New Dispenser 9
Lifting a New Dispenser and Placing it on the Island 10
Adjustable Nozzle Hook Instructions 12
Determining the Number of Product Supply Pipes Needed 14
Mechanical and Plumbing Notes 15
Electrical Field Wiring 15
Pipelines and Under Ground Containment Sumps 17
Above Ground Tank Installations 18
Purging Product Lines for Remote Dispensers 19
Purging Product Lines for Self Contained Dispensers 19
Piping Notes for Self Contained (Suction) Pumps 20
Dispenser Startup and Checklist 21
How to Mechanically Calibrate the SB-100 Meter 23
Operator Instructions 24
Owner Maintenance 26
Maintenance by Bennett Authorized Service Representative 27
Potting Instructions 28
Base Dimensions and Wiring Diagrams 28
Site Audit Form 43
Bennett Limited Warranty for Products Installed in the United States - 3000 Retail & Commercial 46
Bennett International Limited Warranty for Dispensers and Pumps ........................................................ 47

NOTICE

Not all equipment covered in this manual is listed by Underwriters Laboratories. Only those
products that bear the Listing Mark of Underwriters Laboratories are listed.

IMPORTANT

Examine the shipment immediately upon arrival to make certain there has been no damage or loss in
transit. Bennett Pump Company, as shipper, is not liable for the hazards of transportation. Please
make damage claims directly to the truck line.

2 107929 Rev E 04-24-17

 Safety Instructions
WARNING ADVERTISSEMENT ADVERTENCIA

For the safe installation of this equipment, read and understand all warning and cautions. Look for these
warnings:

“DANGER” means: If you do not follow the instructions, severe injury or death will occur.

“WARNING” means: If you do not follow the instructions, severe injury or death can occur.

“CAUTION” means: If you do not follow the instructions, damage can occur to the

DANGER: Fire, explosion, injury or WARNING: Electronic components are

death will occur if fuel filters are changed by static sensitive. Use proper static precautions
untrained personnel. Make sure only trained (static straps) before working on the equipment.
personnel change filters.
WARNING: The emergency shut-off valve
DANGER: To prevent injury to you from (also called the fire valve, shear valve or impact
vehicles and onlookers, always place a barrier valve) must be closed when service or
around this equipment before performing service maintenance is performed on this equipment.
or maintenance.
WARNING: You must have training in the
DANGER: Gasoline is flammable. operation and programming of this dispenser
NO SMOKING OR OPEN FLAME. before using it. READ THE OPERATORS
MANUAL.
DANGER: Disconnect all power to this
equipment and associated submerged pump(s) WARNING: Make sure this equipment is
during installation, service or any maintenance, correctly grounded. Failure to do will cause
i.e., changing filters. injury or damage equipment or improper
operation. Improper grounding voids the
WARNING: You must have training in the warranty.
installation, service or maintenance of this
equipment (dispenser, pump, console, control WARNING: When anchoring the
box or submerged pump) before working on it. dispenser, always level the dispenser with shims
Maintenance repairs must be done by before bolting to the island. DO NOT shim just
authorized personnel only. Warranty work may the middle of the dispenser and bolt down.
only be performed by Bennett certified
technicians. CAUTION: Do not drill holes in fuel
dispensers. Holes can cause failure of the
WARNING: To prevent electric shock, electronic equipment. The warranty will become
keep the electrical parts of the dispenser dry. void. Use only adhesive backed sign mounting
brackets.

READ AND UNDERSTAND ALL WARNING LABELS ATTACHED TO THE DISPENSER

3 107929 Rev E 04-24-17

 Introduction
Mechanical Computer or Non-computer Options
 Fleetmaster 3000 uses Veeder-Root 4-wheel  Veeder-Root pulsers, 10:1 or 100:1 (VR10 us-
non-computer with totalizer. es OPW-FMS “Western” supplied by others for
 Heritage 3000 uses Veeder-Root 4-wheel VR field installation).
10/4 computer with totalizer (optional VR10  2-Stage prepay/preset electric solenoid valve
extended price range computer) for 1 product, 1-hose or 2-product, 2-hose suc-
 U.S. Gallons, Liters or Imperial Gallons for vol- tion pumps. (Valve is standard on all other
ume measurement models)
 Various currency measurements for Heritage  Internal spin on filter & adaptor for remote mod-
3000 series depending upon country applica- els
tion  For High Hose models, Balance vapor coax
 Veeder-Root electric reset, 115 or 230 volt hose outlet and internal vapor return piping
(optional Cam-AC manual reset)  Healy active vapor for High Hose systems
 Sub pump relay 3 phase contactor
Field wiring terminal strip in junction box located in  Valence style top for High Hose models
the top display area (installers should pull 72” (272  Brushed stainless steel lower doors
cm) of wire above grade level). Explosion proof j-  Custom lower door colors and/or graphics
box in lower hydraulic area is optional.  Hose clamp for 5/8”, 3/4”, or 1” I.D. hose
 Explosion proof junction box for lower hydraulic
Hydraulics area
 Precision Bennett SB100 Meter, 4 piston posi-  380 Volt 3-Phase Motors
tive displacement design
 Cam-AC manual reset in lieu of electric reset
 Type 75 Bennett rotary vane pumping unit with
 VR10 Veeder-Root extended price range com-
integral vortex air eliminator
puter for Heritage 3000 series
 All remote units include built in inlet check
 Internal Hose retractor
valves to keep the hydraulics full and prevent
 Strainer in lieu of filter for remotes
meter/pulser count up when the submersible
pump pressurizes the system  Strainer w/ cloth sack for remotes
 Remote units use replaceable paper filter  Strainer w/ cloth sack for suction units
 Suction pumps use re-useable strainer  Hoses, nozzles, swivels
 All units feature 1” hose outlets with 1 x 3/4”
reducer bushing
 1-1/2” ground joint union inlet

4 107929 Rev E 04-24-17

 Mechanical Dispensers and Pump Specification Sheet
Fleetmaster 3000 Volume Only and Heritage 3000 Money/Volume Displays
Standard Features Hydraulics Cont’d
 Mechanical analog display  All remote units include built-in inlet
 Stand-alone or console-controlled when check valves to keep the hydraulics full
pulser options are specified and prevent meter/pulser count-up when
the submersible pump pressurizes the
 Can be controlled by fleet management system
system when pulser options are specified
 Remote units use replaceable paper filter
 Unit of measure for US gallons, liters, or
imperial gallons  Suction pumps use a reusable strainer
 Operates from 115/230Vac, 60/50Hz, or  All units feature 1” hose outlets with a
380 Vac, 50Hz 1”x3/4” reducer bushing
 Self-contained (suction) models feature 1  1-1/2” ground-joint union inlet
-HP continuous duty motors
Options
 Cascade fluorescent dial face lighting
 Veeder-Root Pulsers, 10:1 or 100:1
 Satellite Outlet Connection (VR10 uses OPW-FMS “Western” Pulser
 Self-contained (suction) models: single, supplied by others for field installation).
1-product twin, or 2-product twin  2-Stage prepay/preset electric solenoid
 Remote models: single, 1-product twin, valve for 1-product, 1-hose or 2-product,
or 2-product twin 2-hose suction pumps. (valve is
standard on all other models)
Construction  Internal spin-on filter & adapter for
 Low Hose Cabinet Design or remote models
 High Hose Cabinet Design  For High Hose Models, Balance vapor
 Long-life cabinet construction using coax hose outlet and internal vapor
galvaneal components and powder return piping
coated panels  Vapor recovery nozzle boot kit (field
 Black end panels and top installed) for balanced vapor nozzles
 Black dial face covers  Healy active vapor system for high hose
 Red lower doors (optional colors  Subpump relay 3-Phase Contactor
available)  Intercom speaker for High Hose units
 Hinged swing out lower door  Valance style top for high hose models
 Hinged swing down upper door  Brushed stainless steel lower doors
 Heavy duty hose hook (optional internal  Brushed stainless steel end panels
spring rewind retractor available)  Custom lower door colors and/or
graphics
Mechanical Computer or Non-Computer
 Hose clamp for 5/8”, 3/4”, or 1” I.D. hose
 Fleetmaster uses Veeder-RootTM 4-wheel
non-computer with totalizer  Explosion proof junction box for lower
hydraulic area
 Heritage uses Veeder-Root 4-wheel
VR10/4 computer with totalizer (optional  380 Volt 3-Phase Motors
VR10 extended price range computer)  Pressure-regulating valve for suction
 U.S. Gallons, Liters, or Imperial Gallons pumps with aboveground tank installation
for volume measurement  E85 alcohol blend compatibility option
 Various currency measurements for  Cam-Ac manual reset in lieu of electric
Heritage series depending upon country reset
application  VR10 Veeder-Root extended price range For information on flow rates,
 Veeder-Root Electric Reset, 115 or motor sizes, and model
computer for Heritage 4000 series
configurations see our Model
230volt (optional Cam-Ac manual reset)  Hand Crank for select models with Cam- Configuration Chart &
 Field wiring terminal strip in junction box Ac manual reset Specification Sheet
located in top display area (installers  Internal Hose Retractor
should pull 72” (272 cm) of wire above
grade level). Explosion proof j-box in  Strainer in lieu of filter for remotes
lower hydraulic area is optional.  Strainer w/ cloth sack for remotes ULTM listed
 Strainer w/ cloth sack for suction units Certified for resale applications.
Hydraulics
 Hoses, nozzles, swivels The N.T.E.P. Certificate of
 Precision Bennett SB100 Meter, 4-piston,
positive displacement design  Companion LPS satellites Conformance is available upon
request
 Type 75 or type 75-HD Bennett sliding
vane pumping unit with integral vortex air Specifications in this document
eliminator are subject to change without
notice.

5 107929 Rev E 04-24-17

 Product Specifications
POWER REQUIREMENTS
Motor Power—Standard Motors (self-contained) are 115/230v, 60/50 Hz. An optional 380v, 50
Hz 3-phase motor is available.

Electric Reset - 115volt 50/60Hz OR 230volt 50/60Hz depending on customer specification at

time of order.

Fluorescent Lamps - Ballast is one of four types: 115v 60 Hz OR 115v 50Hz OR 230v 60Hz
OR 230v 50Hz depending on customer specification at time of order.

Two Stage Electric Solenoid Valves - 115v 50/60 Hz OR 230v 50/60 Hz depending on
customer specification at time of order.

ENVIRONMENTAL REQUIREMENTS
Operating Temperature Range: -30° to +50°C
Humidity: 0-95% non - condensing

DIMENSIONS
3000 Series -
Low Hose 60” H X 30” W x 20” D
High Hose 88”H x 30”W x 20”D

6 107929 Rev E 04-24-17

 Determining the Model Number
Determine the model number of the dispenser from the serial plate located in the dispenser. Utilizing
the chart below determine the features of the dispenser to be installed. Understanding the features of
the dispenser to be installed will be helpful in understanding the proper installation of the dispenser.
How a Model for the 3000 Series Dispensers is Made Up.

Pump Model Retail Commercial Activation Method # Products # Hoses Motor

3111 X Electric Reset 1 1 See Note
3211 X Cam AC Reset 1 1
3311 X Electric Reset 1 1
3411 X Cam AC Reset 1 1
3511 X Electric Reset 1 1
3611 X Cam AC Reset 1 1

3112 X Electric Reset 1 2 See Note

3212 X Cam AC Reset 1 2
3312 X Electric Reset 1 2
3412 X Cam AC Reset 1 2
3512 X Electric Reset 1 2
3612 X Cam AC Reset 1 2

3122 X Electric Reset 2 2 See Note

3222 X Cam AC Reset 2 2
3322 X Electric Reset 2 2
3422 X Cam AC Reset 2 2
3522 X Electric Reset 2 2
3622 X Cam AC Reset 2 2

Note - Motor -The hydraulic arrangement can be as follows:

Remote (submerged pump),

Suction with Standard 1 phase 115/230 v.a.c. 50/60 Hz,

Suction with 1 phase 115/230 v.a.c. 50/60 Hz with prepay valves,

Suction with 3 phase 380 v.a.c. 50 HZ,

Suction with 3 phase 380 v.a.c. with pre-pay valves

7 107929 Rev E 04-24-17

Determining the Model Number

8 107929 Rev E 04-24-17

 Unloading, Unpacking, and Inspecting a New Dispenser
Bennett dispensers are bolted to a pallet and then carefully packaged with cardboard/styrofoam liners
and a cardboard exterior carton. The entire package is then securely wrapped with plastic shrink wrap.
Use a fork lift to lift the dispenser from the bottom while it is still on the pallet.

Bennett dispensers are shipped from our factory F.O.B. This means that the title to the equipment
passes to the purchaser at the time the equipment is loaded on the truck at our factory. Freight damage
claims are the responsibility of the purchaser. Bennett will assist you in preparing any damage claim,
by helping you identify and price any parts necessary to make needed repairs.

Before signing the freight delivery receipt, inspect the carton and pallet for any obvious signs of damage
that may have damaged the dispenser. If any damage is found, instruct the delivery driver to make a
notation on the delivery receipt before you sign. If possible, open the carton and inspect the dispenser
before signing the delivery receipt.

Carefully remove the plastic shrink-wrap from the carton. Then carefully remove the cardboard
container and any inside liners. DO NOT DISCARD THE PACKAGING. Should the need arise to
repackage the dispenser, the cardboard packaging can be reused. Plastic shrink-wrap can be
purchased at office supply stores or industrial packaging stores.

Examine the exterior panels for any signs of freight damage. Should you encounter any damage after
signing for delivery, call the freight carrier immediately and request an inspection. DO NOT DISCARD
THE PACKAGING; the inspector will want to examine it.

Once you are sure that there is no freight damage to the exterior of the dispenser, use the door key (one
key is wire tied to the nozzle hook) to unlock the lower door. Remove the lower door from both sides of
the dispenser. Visually examine the interior of the dispenser for shipping damage. While the dispenser
is extremely sturdy, a dispenser that has been “dropped” can suffer damage internally even while it
appears normal on the exterior. Check for and tighten any bolts or nuts that appear loose.

Read the model/serial plate of the dispenser and check to confirm that the hydraulic configuration is
what your order specified.

Report any non-shipping related problems to Bennett Customer Service:

In USA, telephone (800) 235-7618 or outside the USA, telephone (231) 798-1310; or via FAX to (231)
799-6202; or via email to techhelp@bennettpump.com. Or write to us at:

Bennett Pump Company or Bennett Commercial Pump Company

1218 E. Pontaluna Road
Spring Lake, Michigan, USA 49456

9 107929 Rev E 04-24-17

 Lifting a New Dispenser and Placing it on the Island
The dispenser is bolted to a pallet with bolts and nuts. With the lower doors removed and safely stored
away, remove the nuts and bolts that secure the dispenser to the pallet.

Unlock the lower door with the keys that

come with the unit. Swing the door open Remove the door and store in a safe place
90 degrees and lift. until you are ready to put the door back

Fig. 1 - Side View - Using lifting straps to lift Fig. 2 - Front View - Using lifting straps to lift
and move the dispenser. Notice the forks and move the dispenser.
are spread wider than the pump.

Thread two lifting straps (900 lbs. Capacity each minimum) through the dispenser as shown in Figures 1
and 2. Be careful not to allow the straps to go under any of the hydraulic castings such as the meter
outlet, copper tubes or valves. The straps should be lifting only against the front and rear chassis. Use
a forklift or pallet lifting device with the forks spread wider than the pump and gently lift the dispenser.
This lifting method will also work on the high hose dispenser. Place the dispenser gently on the island
using care to line up the base anchor bolt holes with the anchor bolts embedded in the concrete island.

WARNING: Lift only to the height required to set the dispenser on the island. Keep hands and
feet clear of the dispenser while it is suspended in the air.

10 107929 Rev E 04-24-17

 Lifting a New Dispenser and Placing it on the Island
Alternate Method for High Hose
Lifting the Dispenser from Above - On the high hose models, there are lifting brackets provided in the
upper area of the dispenser. There is a cover that has to be removed to access these brackets. (See
Figures 1 + 2 below).

Fig. 1 - Cover is screwed onto the top of the dis- Fig. 2 - After the top cover is removed, the lifting
penser and must be removed to access the lifting brackets can be accessed for lifting the dispenser
brackets. from above.

Anchoring the Dispenser to the Island

The dispenser must be bolted firmly to the concrete island. The dispenser base is provided with anchor
bolt holes (see base drawings in back of this manual for dimensions). Anchor bolts embedded in the
concrete island must be not less than ½” diameter. The threaded ends of the anchor bolts should
project 1½” above the concrete.

On the Low Hose dispenser, 2 anchor bolts required minimum.

On the High Hose dispenser, 4 anchor bolts required minimum in the outer 4 mounting holes.

Refer to the Base Drawings in the back of this manual for hole locations.

When anchoring the dispenser, always level the dispenser with shims before bolting to the island.. Place
the shims at the location of the anchor bolts so the dispenser frame is not distorted when the anchor
bolts are tightened down.

11 107929 Rev E 04-24-17

 Adjustable Nozzle Hook Instructions

For standard interchangeable Use top mounting holes in nozzle

nozzles, use bottom mounting holes hook bracket as shown above for the
in nozzle hook bracket as shown following nozzles: OPW 7H & 7BH;
above. Examples of standard Richards Mark 7 & 7B; Husky VIII,
nozzles are OPW 11A, Husky X. VIIIS, & 1-HS; Emco A6000 series;
Catlow MAX-1

Addendum to 103848, 104652, and 105993 Technical Publications

Part number 106467 Instruction Sheet for Adjustable Nozzle Hook (Rev A 9/02)

12 107929 Rev E 04-24-17

This page intentionally left blank

13 107929 Rev E 04-24-17

 Determining the Number of Product Supply Pipes Needed
Step 1: Determine the type of supply line needed from the model number’s 7th position on the
serial tag. If the model number is 3111SNR (Note the R) the dispenser will require a submerged pump
and pressurized supply line for each product. If the model number is 3111SNS (Note the S) the pump
will require a suction supply line for each product.

Step 2: Determine the number of product pipes required by finding the model number below.

Model Number Product Supply lines required

3111 Use 1 Product Line plumbed to position 1

3211 Use 1 Product Line plumbed to position 1
3311 Use 1 Product Line plumbed to position 1
3411 Use 1 Product Line plumbed to position 1
3511 Use 1 Product Line plumbed to position 1
3611 Use 1 Product Line plumbed to position 1

3112 Use 1 Product Line plumbed to position 1

3212 Use 1 Product Line plumbed to position 1
3312 Use 1 Product Line plumbed to position 1
3412 Use 1 Product Line plumbed to position 1
3512 Use 1 Product Line plumbed to position 1
3612 Use 1 Product Line plumbed to position 1

3122 Use 2 Product Lines plumbed to positions 1 & 2

3222 Use 2 Product Lines plumbed to positions 1 & 2
3322 Use 2 Product Lines plumbed to positions 1 & 2
3422 Use 2 Product Lines plumbed to positions 1 & 2
3622 Use 2 Product Lines plumbed to positions 1 & 2

*Refer to base drawings in the back of this manual for product inlet locations.

Pipe Size - 1-1/2 “ inlet nipples come on all units.

1-1/2” nipple.

14 107929 Rev E 04-24-17

 Mechanical and Plumbing Notes
For remote dispensers, a U.L. Listed Emergency Shut Off Valve is required for each product inlet. The
Emergency Shut Off Valve is sometimes referred to as an “Impact Valve”, “Safety Valve”, “Shear
Valve”, “Crash Valve”, or “Fire Valve”. The Emergency Shut Off Valve must be supported by the island
frame or containment sump frame. Follow all instructions contained in the valve’s installation manual
and observe all local codes.
Install an approved emergency Shut Off valve, designed to close automatically in the event of severe impact
or fire exposure, in the dispenser supply line at the base of the dispenser. The valve will also permit safe
inspection and maintenance. Follow the installation instructions for the valve being installed.

For self-contained (suction) pumps, a vertical check valve is required under each of the
pump’s ground joint unions for the product inlet. The vertical check valve ensures that
the pump’s hydraulic system remains full of product, and it is necessary to maintain the
“prime” of the suction line so that liquid product does not drain back to the tank. Follow all instructions
contained in the vertical check valve’s installation manual and observe all local codes.

For above ground tank installations with suction pump units, a pressure regulating valve is required on
the product line.

Product inlet locations and dimensions are in the base foundation drawings in this manual.

Tighten the dispenser’s ground joint union to leak free tightness. If rigid product inlet pipes are used,
they must be plumed to the proper position so that no strain is exerted on the dispenser chassis when
the ground joint union is tightened.

Electrical Field Wiring

Find the wiring diagram specific to the dispenser model for the dispenser that you are working
on in the “Wiring Diagrams” section in the back of this manual. Read and follow all directions
including supplemental notes contained on the drawing.

The dispenser’s wiring terminal strip for connection of the field wiring is in the ballast box (upper
“Head” ) of the dispenser. Remove the screws securing the top cover of the dispenser to access the
wiring terminal. Also, the dispenser has the option of being ordered with a junction box in the lower part
of the dispenser. If you have this option, you will wire to the terminal strip in the junction box the same
way you would have wired to the terminal strip in the head of the dispenser.

All field wiring must be Oil and gas resistant (THHN) color coded, with a 600 volt insulation rating. See
wiring manual for proper wire sizes. Pull 72” extra wire to reach the top of the dispenser. Do not use wire
nuts. The ends of the wires should be clean and free from oxidation.

No more than two dispensers per 15 amp breaker. All dispensers must be on the same phase of power.

Follow all local, state and federal requirements for installation of vapor seals.

Electrical contractors must pull 72” of wire above the grade level to reach through the dispenser’s
conduit and into the ballast box area at the top of the dispenser. Read and follow all instructions on the
wiring diagram and observe all national and local electrical codes.

In instances where new dispensers are replacing old dispensers, Bennett recommends that new wiring
be pulled to each dispenser.

If existing wiring is to be used (not recommended) does not reach to the dispenser ballast area (top
area) of the dispenser, wire extension is allowed only if the connections are soldered and made weather
proof.

15 107929 Rev E 04-24-17

 Electrical Field Wiring (Cont’d)
The wire separator (supplied with the pump) must be installed on the wires as they exit the conduit
located in the electrical enclosure before the wires are terminated in the electronics enclosure. The wire
separator is needed to properly seal the conduit in the last step of installation.

Underground conduit for the field wiring must be 3/4”, rigid metal and continuous. The use of PVC
conduit is not allowed. All conduit between the building and each dispenser should be a separate
conduit run.

The dispenser may come with or without the optional junction box located in the lower area of the
dispenser. If there is a junction box, follow the instructions for wiring to the j-box under the “Wiring
Diagrams” section of this manual.

Up to two dispensers may be placed on one 15 amp circuit breaker. No more than two dispensers per
15 amp breaker. All dispensers at the station must be on the same phase of power.

All dispenser field wiring between the building and the dispenser for power, neutral and ground wire
conductors must not be spliced, wire nutted or shared with any other equipment. Doing so would void
the Bennett Limited Warranty. All power, neutral and ground conductors shall be run from the dispenser
to the Main Service Panel.

Follow all local, state and federal requirements for installation of vapor seals.

In instances where new dispensers are replacing old dispensers, Bennett recommends that new wiring
be pulled to each dispenser.

If existing wiring is used (not recommended) and does not reach to the dispenser electronic head (top
area) of the dispenser, the wires can be extended only if the connections are soldered and weather
proof and contained in an explosion-proof type junction box.

The maximum distance from the breaker panel to the dispenser is 500 feet. For self-contained units,
increase the motor wire size from 14Ga to 12Ga for runs over 50ft. and to 10Ga. for runs over 100ft, 8
Ga. For runs over 250 feet.

Note: if 230v motor power is used be sure to set the motor switch located on the motor to the high
voltage setting by moving the switch to the high position.

WARNING: DO NOT CROSS PHASE THE DISPENSERS OR DAMAGE WILL OCCUR. When
installing more than one dispenser the remote sub-pump relay control wire from each dispenser must be
on the same phase of power or cross phasing will occur at the sub-pump relay. This means that the
pump power for all dispensers at the site must be on the same phase.

Electrical Conduits - Make sure that each dispenser has it’s own electrical underground conduit. Wiring
from multiple dispensers in a single conduit is not allowed. All underground conduit should be rigid metal
and drawn up tight. The use of PVC (plastic) conduit is not allowed and will void the Bennett Warranty.
Make sure that vapor “seal offs” are properly installed on all conduits at and from each dispenser.

16 107929 Rev E 04-24-17

 Pipelines and Underground Containment Sumps
General -
The dispenser must be mounted on a concrete foundation. Do not pour concrete around the product
pipes or electrical conduit. The use of a UL approved containment sump designed for the Bennett
Dispenser Model used is highly recommended. Follow the containment sump manufacture’s installation
instructions for proper installation. If no containment sump is used, fill the sump area with clean sand or
dirt as far up the product pipe as possible once installation is complete. Use water to pack the sand in
place. See Figures.

Figure 1 - Example of Remote Contained Figure 2 - Example of Self-Contained

NOTE: All piping must be clean of foreign debris, such as: oil, grease and shavings. All
connections must be tight to prevent leaks.
Swing joints or flex pipe must be used at the ends of the horizontal pipe between the dispenser and the
tank. See Figure. These joints prevent leaks which might develop through ground movement from
settling of the tank, frost heaving of the ground or pump island settling. The joint under the dispenser
also aids proper alignment of the product union or coupling.

NOTE: Make sure the installation conforms to EPA regulations for underground storage tanks.

Underground Piping

17 107929 Rev E 04-24-17

 Above Ground Tank Installation with Self Contained Pumps
Bennett self contained dispensers can be used with above ground tank installations if the following
requirements are met:

 An Underwriters (U.L.) Listed Pressure Regulating Valve designed for under-the-pump mounting is
installed for each pumping unit according to the valve manufacturer’s instructions.
 Any additional valves suggested by the Pressure Regulating Valve manufacturer are installed
according to the manufacturer’s recommendations.
 The installation must be installed and used in accordance with Federal, State, Local, and National
Electrical code NFPA #70 and Automotive and Marine service station code NFPA 30A.

18 107929 Rev E 04-24-17

 Purging Product Lines for Remote Dispensers
Once product piping and tanks have been tested for leaks and any leak conditions have been fixed, and
all electrical connections have been made and verified, the remote dispenser product lines must be
purged of all air that may be trapped in the lines.

CAUTION! DO NOT USE THE DISPENSER TO PURGE AIR FROM THE PRODUCT LINES.
RUNNING THE METER IN A DRY CONDITION AND AT THE HIGH SPEEDS RESULTING FROM
PRESSURIZED AIR, WILL DAMAGE THE METER AND VOID THE BENNETT LIMITED WARRANTY.

The emergency shut off valve contains a test port that may be used to bleed off air that may be trapped
in the product lines for remote units. Manually close the emergency shut off valve. Do not leave this
process unattended while purging the air from the product lines. Once liquid fuel product begins to
weep from the test port, retighten the plug in the test port. It is recommended that at least 150 gallons of
fuel be pumped from each hose to eliminate any air in the line. If more than one dispenser is on a
submerged pump product feed line, start this purging process at the dispenser furthest from the
submerged pump and work backwards toward the submerged pump.

WARNING! Take appropriate measures to contain any product seepage from the test port.
Dispose of any spilled product in proper manner consistent with applicable laws and codes.

Manually open the emergency shut off valve and lock it into the “on” position according to the
instructions from the valve manufacturer. Use an approved test can or other appropriate approved
container to dispense 50 gallons or 175 liters through the dispenser. Begin dispensing by only slightly
opening the nozzle to allow any entrapped air in the dispenser to slowly release through the nozzle.
This prevents over-speeding of the meter.

Once the dispenser has dispensed 150 gallons of fuel, the SB100 meter should be tested for calibration.
Refer to the section in this manual for calibration procedures.

Purging Product Lines for Self Contained Systems

Once product piping and tanks have been tested for leaks and any leak conditions have been fixed, and
all electrical connections have been made and verified, the self contained (suction) dispenser product
lines must be purged of all air that may be trapped in the lines.

The pumping unit evacuates all the air in the pipe before it gets to the meter. The air is expelled through
the vent at the top of the pump. Nothing but fuel should pass through the meter. The meter will not turn
until fuel enters the pump and pressurizes the system.

WARNING! Take appropriate measures to contain any product seepage from the air elimination
chamber tube. Dispose of any spilled product in proper manner consistent with applicable laws
and codes.

Use an approved test can or other appropriate approved container to dispense 50 gallons or 175 liters
through the dispenser. Begin dispensing by only slightly opening the nozzle to allow any entrapped air
in the dispenser to slowly release through the nozzle. This prevents over-speeding of the meter.

Once the dispenser has dispensed 150 gallons of fuel, the SB100 meter should be tested for calibration.
Refer to the section in this manual for calibration procedures.

19 107929 Rev E 04-24-17

 Piping Notes for Self Contained (Suction) Pumps
To obtain maximum flow rates on a self-contained pump, follow these guidelines:

The total length of horizontal piping between the pump and tank must be no longer than 60 feet.

Use new 1-1/2” galvanized or approved non-metallic pipe for 10-15gpm pumps. Use new 2” galvanized
or approved non-metallic pipe for 20-24 gpm pumps.

All horizontal piping must be buried a MINIMUM of 18” below the finished grade

The pipe from the tank must slope up to the pump (approximately 1-1/2” to 2” per 10 feet). The piping
run should not have any high or low spots (hills or valleys). The pipe must be supported continuously to
prevent sagging.

All piping must hold a 50 PSI pressure test for 10 minutes.

To absorb ground movement from settling of the tank, frost heaving of the ground or pump island
settling, a swing joint must be used in the supply line at the tank and directly underneath the dispenser.
Three additional directional changes using elbows are permitted.

Only one pumping unit is permitted for each underground pipe. Two pumps on one suction line is not
recommended.

Static lift on self-contained units must not exceed 10 feet (vertical distance between product level in the
storage tank and the center of the pumping unit).

All Installation work must conform to federal, state, and local codes.

Above Ground Tanks - If using above ground tanks, make sure a vacuum actuated pressure regulating
valve is properly installed.

Follow Petroleum Equipment Institute’s Recommended Practices for Installation of Underground Liquid
Storage Systems RP100 and/or Recommended Practices for Installation of Above Ground Storage
Systems for Motor Vehicle Fueling RP200.

Copies of PEI’s recommended practices can be order through their web site at: www.pei.org

20 107929 Rev E 04-24-17

 Dispenser Startup and Checklist
DANGER: Fire, explosion, injury or death will occur if fuel vapors are present. Make sure
there are no vapors present before starting this procedure.

CAUTION: To prevent damage to the dispenser, follow the proper start-up procedures.

Before applying AC power to the dispenser, follow this procedure:

1. Unlock and open the upper and lower dispenser doors.

2. Check to make sure:

 The components have not come loose from shipping.
 The cables are properly connected. There are no torn cables or stranded harnesses.
 Pulser and pump handle harnesses are connected properly.

3. Make sure the shut off valves are closed.

4. Turn off all submerged pump circuit breakers and all other circuit breakers to the dispenser.
Make sure the 12-gauge green ground wire is properly connected between the dispenser and the
ground bus at the Main Service Panel.

Check the Dispenser Power Circuit

1. Turn on 115 or 230 Volts AC dispenser power to the unit.

2. Use a voltmeter to verify 115 or 230 Volts AC only at Terminal 10 on the dispenser terminal strip.
Terminal 2 of the terminal strip is neutral. This AC circuit provides power to the electric reset.

Check the Submerged Pump Motor Circuit:

Remotes
WARNING: To prevent injury, make sure impact valves and submerged pump breakers
are off.

1. Put the 1st Product’s pump handle in the ON position. The dispenser will reset (all 000’s on the
mechanical display). Use a voltmeter to verify 115 or 230 Volts AC across the two black wires
coming out of the Electric Reset. This is the voltage that is used to energize the control relay coil.
Refer to the Wiring Diagram for Remote Dispensers in the back of this manual.

2. Put the 1st Product pump handle in the OFF position.

3. Open and set the Shut Off (impact) valves.

21 107929 Rev E 04-24-17

 Dispenser Startup and Checklist (Cont’d)
Self-Contained

WARNING: If the lower door on the pulley side of the unit is off, close the door and lock it to
prevent injury.

1. Verify that the motor voltage select switch on the self contained motor is in the proper position.
2. Turn on this products self contained pump motor circuit breaker. With the pump handle OFF, use a
voltmeter to verify 115/230 Volts AC power for the self contained pump motor by measuring
between the two black wires coming out of the electric reset. These wires should be connected to
the field wires for the pump motor power. If the motor is being operated off of 230 volts, this reading
will measure 230 Volts A.C. This products pump motor should not be running at this time.

3. Turn off this product’s pump motor circuit breaker.

4. Repeat this test for any remaining dispensers.

All Dispensers

1. Turn off all circuit breakers.

2. Close and lock the lower doors and the upper doors.

3. Turn the circuit breaker for the system on.

4. Purge the air from the system.

5. Dispense a small amount of fuel from each hose to verify all positions are counting.

Proceed to the section for finishing the installation called “Potting Instructions”.

Then proceed to the section titled “How to Calibrate the SB-100 Meter” .

22 107929 Rev E 04-24-17

 How to Calibrate the SB-100 Meter
The Bennett SB-100 Meter is built to maintain accurate measurement under normal operating
conditions. The meter is a positive displacement device with rods and pistons, which require a break in
period. The meter is calibrated at the factory using a solvent for safety purposes, and must be
calibrated after it has been installed. We strongly suggest recalibration of the meter after a 90 day break
in period.
Each SB-100 meter is provided with the following Example 1
calibration information:
1. A fast flow test at 11 GPM shows a +3 cu. in.
 The dial adjusting cover has (+) and (-) arrows
reading in a five gallon test measure.
to indicate the correct direction to rotate the
dial to either increase or decrease delivery. 2. Remove the existing seal and pin and turn the
 A self-adhesive metal label listing the minimum dial clockwise (-)five minimum adjustments
incremental adjustment is attached to the (half holes) and reinsert the pin.
collector housing immediately above the
3 cu. in. = 5 half holes (-)CW
adjusting dial.
The dial cover has two pin hubs, one to the left of .6 cu. in./adjustment
the shaft and one to the right. The seal pin may be
inserted in either hub. See Figure 21. The 3. Test and reseal.
smallest adjustment (.6 cu. in.) occurs when the
pin is pulled from one side and inserted in the other Example 2
side by moving the dial the least amount or half a
hole. A 1.2 cu. in. adjustment is made by pulling 1. A fast flow test at 11 GPM shows a -2 cu. in.
the pin and turning the dial until the next adjacent reading in a five gallon test measure.
hole aligns with the same hub and reinserting the
pin. 2. Remove the existing seal and pin and turn the
dial counterclockwise (+) three minimum
To calibrate the meter, follow this procedure: adjustments (half holes) and reinsert the pin.
1. Measure the actual delivery of the meter at fast
flow in an accurate test measure. Dispense a 2 cu. in. = 3 half holes (+) CCW
minimum of 5 gallons (20 liters).
.6 cu. in./adjustment
2. Cut and remove the existing seal wires and
remove the seal pin. See Figure 22. 3. Test and reseal
3. Turn the dial the necessary amount in the (+)
or (-) direction to increase or decrease the
quantity of fuel delivered.
4. Re-insert the seal pin in the desired pin hub.
5. Dispense 5 gallons (20 liters) of fuel to allow
the meter to adjust to the new settings. Do not
make any adjustments based on this delivery.
6. Make sure the meter is properly calibrated.
Dispense another 5 gallons (20 liters) of fuel
into an official test measure to check the
calibration.

23 107929 Rev E 04-24-17

 Operator Instructions
DANGER: Gasoline is flammable.
NO SMOKING OR OPEN FLAME WITHIN 100’ OF THE EQUIPMENT.

DANGER: Fire, explosion, injury or death will occur if untrained personnel change fuel filters.
Make sure only trained personnel change filters.

The Bennett mechanical computing fuel dispenser is simple to operate:

ELECTRIC RESET ACTIVATION

1. Remove nozzle from the dispenser’s nozzle boot.

2. Insert nozzle fully into the vehicle fill pipe.

3. Rotate On-Off Lever fully to the “On” position .

 The electric reset will turn on (you can usually hear the reset motor running)

 The computer or non-computer dials will reset to zero.

 The self-contained pump’s motor will turn on or if it is a remote dispenser you will hear the
electric solenoid valve click open.

4. Squeeze the nozzle lever and dispense the desired amount of fuel. Some nozzles will be
automatic shut-off style and may be equipped with a latch open device, which can be set at
several flow rate points. If the nozzle is not equipped with a latch open device, you must hold
the nozzle lever open. DANGER: Do not attempt to block open the nozzle lever with any
foreign objects.

DANGER: The operator must remain in view of the nozzle at all times while the dispenser
is on or while the nozzle is removed from the dispenser’s nozzle boot.

5. When the desired amount of fuel has been dispensed into the vehicle, close the nozzle.

6. Turn the dispenser’s on/off handle to the “Off” position.

7. Return the nozzle to the nozzle boot of the dispenser.

8. Replace the vehicle’s fuel cap.

DANGER: No not dispense fuel into unapproved containers.

24 107929 Rev E 04-24-17

 Cam Reset Activation
1. Remove nozzle from the dispenser’s nozzle boot.

2. Insert nozzle fully into the vehicle fill pipe.

3. Rotate the Reset Handle (small handle)

 The computer or non-computer dials will reset to zero.

4. Rotate On-Off Lever fully to the “On” position .

 The self-contained pump’s motor will turn on or if it is a remote dispenser you will hear
the electric solenoid valve click open.

5. Squeeze the nozzle lever and dispense the desired amount of fuel. Some nozzles will be
automatic shut-off style and may be equipped with a latch open device, which can be set at
several flow rate points. If the nozzle is not equipped with a latch open device, you must hold
the nozzle lever open. DANGER: Do not attempt to block open the nozzle lever with any
foreign objects.

DANGER: The operator must remain in view of the nozzle at all times while the dispenser
is on or while the nozzle is removed from the dispenser’s nozzle boot.

6. When the desired amount of fuel has been dispensed into the vehicle, close the nozzle.

7. Turn the dispenser’s on/off handle to the “Off” position.

8. Return the nozzle to the nozzle boot of the dispenser.

9. Replace the vehicle’s fuel cap.

DANGER: No not dispense fuel into unapproved containers.

25 107929 Rev E 04-24-17

 Owner Maintenance
Some maintenance can be done without authorized service technicians if you read and follow all the
safety precautions contained in this manual. Owners can do the following items:

Visual Inspection for Leaks

Bennett recommends that a visual inspection be done at least once a month or if a leak is suspected.

WARNING: Turn off and lockout all circuit breakers associated with the dispenser to be
inspected.

WARNING: Blockade the work area around the dispenser to protect yourself from traffic.

Unlock the door of the dispenser, carefully swing open and secure the door.

Check for signs of dripping fuel or wet areas on all hydraulic connections and major components such
as the meter, pumping unit, filter and filter casting, etc.

If any sign of leaking fuel is detected, call an authorized Bennett Service Technician immediately.

Lubricating Door Locks

Use a graphite lock lubricant and follow directions on the lubricant container. Cleanup any excess so
that it will not stain the painted surfaces of the dispenser.

Internal or External Hose Retractors

Inspect weekly to ensure that the nylon retractor cable is not wound around the product hose.

Cleaning Exterior

Clean all painted surfaces as needed with a mild detergent and water solution. Do NOT use a high
pressure water sprayer to clean or rinse the dispenser.

Clean stainless steel surfaces with a non-abrasive cleaner intended for cleaning stainless steel. Read
and follow all directions on the cleaner container.

To preserve the luster and lengthen the life of all metal surfaces, use a high grade automobile paste
wax. Read and follow all directions on the wax container. Clean all surfaces prior to waxing.

Do NOT use any harsh detergents, degreasers, or cleaners with abrasives.

26 107929 Rev E 04-24-17

 Maintenance by Bennett Authorized
Service Representatives
The following maintenance/service procedures should be performed ONLY by Bennett Authorized
Service Representatives.

Manually Opening or Closing the Emergency Shut-off Valve or Testing the Valve’s Operation

Emergency Shut-off Valves (Shear Valves, Impact Valves, Crash Valves) are required at the dispenser
inlet for all remote dispensers. The valve incorporates a shear section so that the valve will close if a
vehicle strikes a dispenser. The valve also incorporates a fusible link so that it will close in the event of
a fire.

Use only Bennett Authorized Service Representatives for this type of service.

Changing Filters or Cleaning Strainers

Use only Bennett Authorized Service Representatives for this type of service.

Replacing or Repairing Hanging Hardware (Hoses, Nozzles, Swivels, Break-a-ways

Use only Bennett Authorized Service Representatives for this type of service.

Servicing any electrical or hydraulic components

Use only Bennett Authorized Service Representatives for this type of service.

27 107929 Rev E 04-24-17

 Potting Instructions
1. Install field conduit dispenser per NFPA-70 along with any state
and local codes.
2. Pull field wiring allowing 72” of extra wire to reach upper electrical
enclosure.
3. Feed wire through conduit and into upper electrical enclosure.
CAUTION: Don not damage wire while feeding through
conduit into the upper electrical enclosure.
4. Wrap some “CHICO X” fiber around wires and push into conduit
assembly to prevent potting from running down the length of the
conduit. See figure.
5. Using the wire separator provided, install one wire in each hole
until all wires are separated. See Figure.
6. Shorten field wiring to appropriate length when making
connections.
7. Attach field wiring to terminal strip in upper electrical enclosure
according to the wiring diagram supplied for this dispenser. See
Figure.
8. Push wire separator at least 3/4” into conduit.
9. Prepare potting compound according to directions.
NOTE: Use “CHICO A3” potting compound for sealing
fittings in hazardous locations.
10. Using a funnel, pour potting into conduit, be sure to get potting in
between each wire. See Figure.
11. Let stand until firm.

Footprint Dimensions and Wiring Diagrams

Find the appropriate footprint dimensional drawings and wiring diagram for the model of dispenser being
installed in the next section of this manual. Read and follow all directions and safety notices.

WARNING: RISK OF ELECTRICAL SHOCK – More than one disconnect switch may be required to de
-energize the device for serving.

Note - Dispenser electrical disconnect must comply with National Electrical Code, NFPA 70.

WARNING: All doors must be replaced and locked when unit is in service.

WARNING: EXPOSED BELTS AND PULLEYS. Do not operate pump with door removed except
when required for maintenance and then only by a Bennett Authorized Service Representative. Keep
clear of belts and pulleys.

28 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

29 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

30 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

31 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

32 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

33 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

34 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

35 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

36 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

37 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

38 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

39 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

40 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

41 107929 Rev E 04-24-17

Footprint Dimensions and Wiring Diagrams

42 107929 Rev E 04-24-17

3000 Series Mechanical Site Audit Form

43 107929 Rev E 04-24-17

3000 Series Mechanical Site Audit Form (Cont’d)

44 107929 Rev E 04-24-17

Bennett Limited Warranty for Products Installed in the United States - 3000 Retail & Commercial

Bennett Pump Company guarantees new Service Station Equipment manufactured by Bennett against defects in material or workmanship
during the warranty period in accordance with the provisions stated below:
 The Site Audit Report issued with all equipment must be completed and returned at time of installation to Bennett Pump Company, Spring Lake,
MI to initiate warranty.
 Warranty service must be performed by the nearest Bennett Authorized Service Representative qualified to perform service on the defective
equipment. Only Authorized and Certified Service Representatives are allowed to perform warranty service. Use of service personnel other than
qualified Bennett Service Representatives without prior approval by Bennett Pump Company will void payment of any warranty claims.
 Labor and travel costs incurred while servicing Bennett equipment will be paid at previously contracted rates subject to published standard repair
time allowances to qualified Bennett Service Representatives with travel cost limited to 200 miles. Travel cost shall be limited to 4 hours round trip.
 Bennett equipment has been installed according to the manufacturer’s instructions and diagrams.
 During the warranty period, Bennett Pump Company will, at its option, repair or replace defective parts returned to its factory, transportation
charges prepaid.
 The manufacturer reserves the right to make changes in the design or to make additions

Dispensers – 3000 Series Retail & Commercial Self Contained and Remote
Warranty on parts, labor, and travel is 12 months from date of installation or 18 months from date of Bennett’s original invoice, whichever comes first.

Warranty excludes nozzles, hoses and fittings, hose retractor, hose reels, filters, belt adjustments, paper jams, light bulbs, or any leaks after the installation start-up and audit.
Minor adjustments such as meter calibration, pulser adjustments, and handle switch adjustments, customer specified items manufactured by others, and customer requested
reprogramming of equipment are not covered by warranty.

Field Retrofit Card Readers, Payment Modules, Cash Acceptors, and all other field retrofit Accessories
The field retrofit assembly is warranted for parts only for 12 months from date of installation or 18 months from date of original invoice, whichever comes first, except the
receipt printer and driver board which is warranted for parts for ninety (90) days from the date of installation or 180 days from original invoice, whichever comes first.

Consumable Items such as receipt paper are not warranted. The use of receipt paper not specified by Bennett will void the printer assembly warranty.

Model 515 Pump Controller, 621 Module, Fan Out Boxes

Warranty on parts, labor and travel is 12 months from the date of installation or 18 months from the date of original invoice, whichever comes first.

Software
Bennett Pump Company warrants Bennett products and software packages, whose operation is controlled by Bennett designed and developed software, shall be free of
material defects and conform to current Bennett specifications for a period of ninety (90) days from the date of original invoice. Bennett shall use its best effort to correct such
defects and to supply to purchaser at Bennett’s expense, a corrected version within a reasonable time after purchaser notifies Bennett in writing of any defects and provides
the programs and instructions required to reproduce the claimed defect.

Warranty does not cover any modification to the program, the Bennett product, and/or connection to unapproved equipment made by any person or any defect caused by
such modifications/connections.

Upgrade Kits
Bennett offers kits which are installed as an option to enhance operating features of an existing Bennett product are warranted for parts only for ninety (90) days from date of
installation or 12 months from date of original invoice, whichever comes first. Upgrade Kit warranty applies to kit components only. Warranty status of the remainder of the
product remains unchanged.

Spare Parts
For equipment under warranty: The warranty period for all spare parts replaced is the remainder of the original warranty. Spare Parts are warranted for the value of the parts
only (no labor, mileage, or other charges).

For equipment not under warranty: The warranty period is 90 days from the date of invoice to the end user, or 12 months from the date of original invoice, whichever comes
first. Spare Parts are warranted for the value of the parts only (no labor, mileage, or other charges).

General Exclusions
1. Warranty does not apply to any product which has been altered, subjected to unusual physical or electrical stress, an Act of God, damaged by
accident, tampered with, or subjected to misuse or abuse including substituting parts or accessories from other manufacturers without the written
consent of Bennett Pump Company. The above warranties shall not exist if the original identification marks have been removed or altered.
2. Bennett makes no warranty with respect to the Bennett equipment or Bennett’s performance of services under this agreement, express or implied,
and Bennett hereby disclaims the implied warranties of merchantability and fitness for a particular purpose.
3. In no event shall Bennett be liable for any loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential
damages of any kind in connection with or arising out of the furnishing, performance, use or failure of the Bennett equipment, software or services
acquired from Bennett, the distributor or the user, whether alleged as a breach of contract or tortuous conduct, including negligence. Bennett’s
liability hereunder for damages shall not, in any event, exceed the amounts paid by the buyer to Bennett for equipment, software or services as to
which the claim arose.
4. No action arising out of any claimed breach of the Warranty Agreement or transaction under this Warranty Agreement may be brought by either
party more than two (2) years after the cause of action has accrued.
5. Use of non-Bennett replacement parts, unless specified by Bennett, will void the equipment warranty.
6. This warranty only applies to Bennett equipment installed in the United States of America and is non-transferable.
7. Failure to pay the Bennett invoice within stated invoice terms, covering the respective Bennett equipment purchased under this limited warranty
may, at Bennett’s discretion, void this limited product warranty.

THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING,
WITHOUT LIMITATION, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

BENNETT PUMP COMPANY

1218 E. Pontaluna Road
Spring Lake, MI 49456 45 107929 Rev E 04-24-17
Tel: 231-798-1310 Fax: 231-799-6202
Form 1-1010-2 Rev B 10-20-14
 Bennett International Limited Warranty for Dispensers and Pumps

Bennett Pump Company guarantees new Service Station Equipment manufactured by Bennett against defects in material or workmanship
during the warranty period in accordance with the provisions stated below:
 The Site Audit Report issued with all equipment must be completed and returned at time of installation to Bennett Pump Company, Spring Lake,
MI to initiate warranty.
 Warranty service must be performed by the nearest Bennett Authorized Service Representative qualified to perform service on the defective
equipment. Only Authorized and Certified Service Representatives are allowed to perform warranty service. Use of service personnel other than
qualified Bennett Service Representatives without prior approval by Bennett Pump Company will void payment of any warranty claims.
 Labor and travel costs incurred while servicing Bennett equipment is not covered under this limited warranty.
 Bennett equipment has been installed according to the manufacturer’s instructions and diagrams.
 During the warranty period, Bennett Pump Company will, at its option, repair or replace defective parts returned to its factory, transportation
charges prepaid.
 The manufacturer reserves the right to make changes in the design or to make additions

Dispensers (Remote and Self-contained styles) (excluding Natural Gas, Hydrogen and Hydraulic-less Dispensers)
The Warranty will cover repair or replacement, at Bennett’s option, of the parts only that are deemed to be defective in material or workmanship at Bennett’s discretion, for a
period of 12 months from date of installation or 18 months from date of Bennett’s original invoice, whichever comes first.

Warranty excludes nozzles, hoses and fittings, hose retractor, filters, belt adjustments, paper jams, light bulbs, or any leaks after the installation start-up and audit. Minor
adjustments such as meter calibration, pulser adjustments, and handle switch adjustments, customer specified items manufactured by others, and customer requested repro-
gramming of equipment are not covered by warranty.

Field Retrofit Card Readers, Payment Modules, Cash Acceptors, and all other field retrofit Accessories
The field retrofit assembly is warranted for parts only for 12 months from date of installation or 18 months from date of original invoice, whichever comes first, except the
receipt printer and driver board which is warranted for parts for ninety (90) days from the date of installation or 180 days from original invoice, whichever comes first.

Consumable Items such as receipt paper are not warranted. The use of receipt paper not specified by Bennett will void the printer assembly warranty.

Model 515 Pump Controller, 621 Module, Fan Out Boxes

Warranty on parts only is 12 months from the date of installation or 18 months from the date of original invoice, whichever comes first.

Software
Bennett Pump Company warrants Bennett products and software packages, whose operation is controlled by Bennett designed and developed software, shall be free of
material defects and conform to current Bennett specifications for a period of ninety (90) days from the date of original invoice. Bennett shall use its best effort to correct such
defects and to supply to purchaser at Bennett’s expense, a corrected version within a reasonable time after purchaser notifies Bennett in writing of any defects and provides
the programs and instructions required to reproduce the claimed defect.

Warranty does not cover any modification to the program, the Bennett product, and/or connection to unapproved equipment made by any person or any defect caused by
such modifications/connections.

Upgrade Kits
Bennett offers kits which are installed as an option to enhance operating features of an existing Bennett product are warranted for parts only for ninety (90) days from date of
installation or 12 months from date of original invoice, whichever comes first. Upgrade Kit warranty applies to kit components only. Warranty status of the remainder of the
product remains unchanged.

Spare Parts
For equipment under warranty: The warranty period for all spare parts replaced is the remainder of the original warranty. Spare Parts are warranted for the value of the parts
only (no labor, mileage, or other charges).

For equipment not under warranty: The warranty period is 90 days from the date of invoice to the end user, or 12 months from the date of original invoice, whichever comes
first. Spare Parts are warranted for the value of the parts only (no labor, mileage, or other charges).

General Exclusions
1. Warranty does not apply to any product which has been altered, subjected to unusual physical or electrical stress, an Act of God, damaged by
accident, tampered with, or subjected to misuse or abuse including substituting parts or accessories from other manufacturers without the written
consent of Bennett Pump Company. The above warranties shall not exist if the original identification marks have been removed or altered.
2. Bennett makes no warranty with respect to the Bennett equipment or Bennett’s performance of services under this agreement, express or implied,
and Bennett hereby disclaims the implied warranties of merchantability and fitness for a particular purpose.
3. In no event shall Bennett be liable for any loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential
damages of any kind in connection with or arising out of the furnishing, performance, use or failure of the Bennett equipment, software or services
acquired from Bennett, the distributor or the user, whether alleged as a breach of contract or tortuous conduct, including negligence. Bennett’s
liability hereunder for damages shall not, in any event, exceed the amounts paid by the buyer to Bennett for equipment, software or services as to
which the claim arose.
4. No action arising out of any claimed breach of the Warranty Agreement or transaction under this Warranty Agreement may be brought by either
party more than two (2) years after the cause of action has accrued.
5. Use of non-Bennett replacement parts, unless specified by Bennett, will void the equipment warranty.
6. This warranty only applies to Bennett equipment installed outside the United States of America and is non-transferable.
7. Failure to pay the Bennett invoice within stated invoice terms, covering the respective Bennett equipment purchased under this limited warranty
may, at Bennett’s discretion, void this limited product warranty.

THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING,
WITHOUT LIMITATION, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

BENNETT PUMP COMPANY

1218 E. Pontaluna Road
Spring Lake, MI 49456
Tel: 231-798-1310 Fax: 231-799-6202 46 107929 Rev E 04-24-17

Form 1-1010-8 Rev B 10-20-14

 Revision Log

Revision Date Description

A - -
B - -
C - -
D 9/22/14 -
E 4/24/17 Add International Warranty

47 107929 Rev E 04-24-17

 48 107929 Rev E 04-24-17

Bennett 1218 E. Pontaluna Road, Spring Lake, MI 49456

USA 800-235-7618 ~ Outside USA 231-798-1310
sales@bennettpump.com ~ www.bennettpump.com