IQ™ Network Communication Cartridge (IQ-NCC)

Installation & User Guide for the IQ™ Central Control System
Symbols Rain Bird Support
For technical assistance contact Rain Bird

NOTE: Symbol alerts the user to important operating,
functionality, installation or maintenance instructions. Technical Services at 1-800-247-3782


WARNING: Symbol alerts the user to the presence of Visit us on the web at www.rainbird.com
electricity or electromagnetic energy which may constitute
a risk of electric shock, radiation exposure or other hazard. Or contact Rain Bird Global Support Plan:

CAUTION: Symbol alerts the user to important instructions U.S. and Canada
dd
or conditions that could seriously affect irrigation effectivity 1-866-477-9778
or device operation. gsp@rainbird.com

gg
DIAL: Symbol alerts user of requirement to turn the dial Australia
on the device to an appropriate setting in order to follow 1800 225 512
subsequent instructions. info@rainbird.com.au
REPEAT: Symbol indicates that a repetition of previous
Europe
steps or actions may be required in order to continue or
+33 4 42 24 44 61
complete the process of programming the device.
EuropeGSP@ rainbird.fr

International
1-520-434-6216
gsp@rainbird.com
Contents
Introduction................................................... 1 Box Contents......................................................... 6
Welcome to Rain Bird............................................ 1 Figure 3 - Box Contents.................................................... 7
About This Manual.................................................................. 1 Cartridge Installation........................................... 8
ESP-LX Series Controllers..................................................... 1 Access Controller Cabinet................................................... 8
IQ™ Central Control System................................... 1 Remove the Communication Cable Knock-out....... 9
IQ™ Network Communication Cartridge..................... 1 Install an External Antenna for LXMM.........................10
Types of IQ™ Satellite Controllers..................................... 2 Install the Cartridge.............................................................12
Direct Satellite...................................................................... 2 Figure 4 - Installation/ Cable Options.....................13
Server Satellite...................................................................... 2 Complete Cable Connections.........................................15
Client Satellite....................................................................... 2 Internal Antenna Installation...........................................18
Products Covered in this Manual......................... 2 IQ-NCC Configuration......................................... 20
Figure 1 - IQ™ Network Communication Direct Satellite Setup Wizard...........................................20
Cartridge................................................................................. 3 Server Satellite Setup Wizard...........................................22
Client Satellite Setup Wizard............................................24
Installation..................................................... 4 NCC Configurator Software................................ 25
IQ™ Network Communication Cartridge
Components.......................................................... 4 Operation..................................................... 26
Network Communication Cartridge.............................. 4 Controls and Indicators...................................... 26
IQ Port Cable or Antenna.................................................... 4 Reset Button............................................................................26
Connection Module (CM).................................................... 4 LED Indicators.........................................................................26
Connection Module (CM) Port Cable............................ 4 Table 1 - IQ Port LED Indicators..................................27
Radio Modem Cable.............................................................. 4 Table 2 - CM Port LED Indicators...............................28
Configuration Options.......................................... 4 Table 3 - Radio Port LED Indicators..........................28
Figure 2 - Installation Overview................................... 5
IQ Network Communication Cartridge I
 Status Menu........................................................ 29
Direct Satellite Controllers................................................29
RS-232, Phone or Ethernet............................................29
GPRS or WiFi.........................................................................30
Server Satellite Controllers...............................................31
RS-232, Phone or Ethernet............................................31
GPRS or WiFi.........................................................................32
Client Satellite Controllers................................................33
IQNet Alarms Menu............................................. 34
Appendix...................................................... 36
Connection Modules........................................... 36
Connection Module Options...........................................36
Base Module........................................................................36
Flow Smart Module..........................................................36
IQ Connection Module...................................................37
IQ Flow Smart Connection Module..........................37
Connection Module Installation....................................38
Connect IQ-CM Grounding Wire...............................40
SIM Card Installation.......................................... 41

II IQ Network Communication Cartridge

Introduction
Welcome to Rain Bird IQ™ Central Control System
Thank you for purchasing your new state-of-the-art Rain The IQ Central Control System provides remote
Bird IQ Network Communication Cartridge (IQ-NCC) for the communication capability for programming and monitoring
IQ Central Control System. For more than seven decades, multiple ESP-LXME and ESP-LXD Satellite Controllers from a
Rain Bird has led the irrigation industry in meeting all of your single personal computer.
water management needs by providing the highest quality
products and services available.
IQ™ Network Communication Cartridge
The addition of an IQ Network Communication Cartridge
About This Manual (IQ-NCC) turns a new or existing ESP-LXME or ESP-LXD into
This manual is an addendum to ESP-LX Series Controller an IQ Satellite Controller.
Installation & Operations Guides. The instructions in this Five types of Network Communication Cartridges are
manual guide you through installing an IQ-NCC Cartridge available to provide communication with the IQ Central
in an ESP-LX Controller (not included), connecting the Computer:
communication cables or antenna, and configuring the
cartridge for communication with the IQ computer or IQ llRS-232 (External Modem or Computer Direct Connect-
Server Satellite Controller. also used for IQ Client Satellite Communication with an IQ
Server Satellite)
ESP-LX Series Controllers
llPhone (Telco)
Rain Bird ESP-LXME and ESP-LXD controllers normally
operate as stand-alone irrigation controllers, but can be llEthernet (Wired LAN Network)
upgraded to become field components of the IQ Central llGPRS (Cellular)
Control System with the installation of an IQ Network
Communications Cartridge.
llWiFi (Wireless LAN Network)

IQ Network Communication Cartridge 1

Types of IQ™ Satellite Controllers Products Covered in this Manual
IQ Satellite Controllers are configured as either a Direct, This manual describes the installation of the following
Server, or Client Satellite. The differences and capabilities Rain Bird IQ™ products:
of each are listed below:
ll RS-232 Network Communication Cartridge (IQ-NCC-RS)
Direct Satellite
ll Phone Network Communication Cartridge (IQ-NCC-PH)
Direct Satellites communicate with the IQ Central Computer
through a wired or wireless connection to an IQ-NCC. Direct ll Ethernet Network Communication Cartridge (IQ-NCC-EN)
Satellites do not communicate with other Satellites. ll GPRS/Cellular Network Communication Cartridge
Server Satellite (IQ-NCC-GP)
Server Satellites communicate with the IQ Central Computer ll WiFi Network Communication Cartridge (IQ-NCC-WF)
through a wired or wireless connection with an IQ-NCC. ll GPRS/Cellular External Antenna (IQ-EXTANT-GP)
Communication with up to 149 Client Satellites over the
IQNet is accomplished using a radio modem or a high-speed ll WiFi External Antenna (IQ-EXTANT-WF)
communication cable connection. (An optional IQ-FSCM- ll IQ-FSCM-LXME Flow Smart Connection Module
LXME or IQ-CM-LXD Connection Module must be installed
to establish a cable connection.) ll IQ-CM-LXD Connection Module


Client Satellite NOTE: The IQ-NCC-GP cartridge requires a SIM card
Client Satellites communicate with the Server or other and GPRS/cellular telemetry service account that is
Client Satellites over the IQNet using a radio modem or a not provided and must be purchased separately. See
high-speed communication cable connection. (An optional the SIM Card Installation section in the Appendix for
IQ-FSCM-LXME or IQ-CM-LXD Connection Module must be details.
installed to establish a cable connection.)

2 IQ Network Communication Cartridge

Figure 1 - IQ™ Network Communication Cartridge
(IQ-NCC-GP shown)

IQ Network Communication Cartridge 3

Installation
This section provides instructions for installing and Connection Module (CM) Port Cable
configuring an IQ Network Communication Cartridge into The Connection Module (CM) Port cable provides the
an ESP-LXME or ESP-LXD controller. connection between the IQ-NCC and the CM.
IQ™ Network Communication Radio Modem Cable
Cartridge Components A radio modem can also be connected to the IQ-NCC to
provide wireless radio communication between Server and
Network Communication Cartridge Client Satellites on the IQNet.
Five types of cartridges are available to communicate with
the IQ Central Computer through a direct cable connection, Configuration Options
external modem, phone line, wired or wireless LAN, or a Before beginning installation, the following configuration
GPRS/Cellular network. options need to be determined and/or identified:
IQ Port Cable or Antenna llType of Cartridge (RS, PH, EN, GP, or WF)
The IQ Port cable or antenna provides communication with llType of Satellite Controller (Direct, Server, Client)
the IQ Central Computer.
llType of communication with other satellites (wireless
Connection Module (CM) connection using a radio modem, wired connection using
The Connection Module (CM) installed in your ESP-LX an IQNet PE Communication Cable, or none)
Controller allows high-speed cable communication between llController model (ESP-LXME or ESP-LXD)
Server and Client Satellites on the IQNet.
llType of connection to the IQ computer (direct cable
connect, external modem, phone cord, Ethernet cable,
cellular or WiFi antenna)

4 IQ Network Communication Cartridge

 7
3b.
1

6
A ESP-LX Controller Front Panel D IQ Port Cable (or Antenna)
5
B IQ Network Communication
Cartridge (IQ-NCC-EN shown)
E Ground Wire (to earth ground)
3a.
F IQNet PE Communication
4
C Connection Module (CM) Cable
(CM Y-Cable shown)
Cable to other Satellites

a. To IQNet Radio Modem G Connection Module

(FSCM-LXME shown)
b. To Connection Module Figure 2 - Installation Overview

IQ Network Communication Cartridge 5

Box Contents 3. IQ Computer Connection Cable or Antenna
(ONE of the following):
The following components are included with each IQ-NCC
and are required for installation. llRS-232 External Modem Cable (IQ-NCC-RS)
llRJ-11 Phone Cord (IQ-NCC-PH)

NOTE: If anything is missing, please contact your
distributor before proceeding. llRJ-45 Ethernet Cable (IQ-NCC-EN)
1. IQ Network Communication Cartridge llGPRS/Cellular Internal Antenna (IQ-NCC-GP)
(ONE of the following): llWiFi Internal Antenna (IQ-NCC-WF)
llIQ-NCC-RS (RS-232) 4. Installation & User Guide
llIQ-NCC-PH (Phone)
llIQ-NCC-EN (Ethernet)
llIQ-NCC-GP (GPRS/Cellular)
llIQ-NCC-WF (WiFi)
2. Cartridge to Connection Module cables
(BOTH of the following):
llCM Y-Cable.
llCM Straight Cable

6 IQ Network Communication Cartridge

Connection Module IQ Port Cable
(CM) Cables Options
RS-232 External
Modem Cable
CM Y-Cable (Beige)
(black)

RJ-11 Phone
Cord (Silver)

CM Straight
Cable (black) RJ-45 Ethernet
Cable (Green)

GPRS/Cellular
IQ Network Internal
Antenna (Gold)
Communication
Cartridge (IQ-NCC)
WiFi Internal
Installation & Antenna (Gold)
User Guide

Figure 3 - Box Contents

IQ Network Communication Cartridge 7

Cartridge Installation C Pull the handle towards you and swing it to the left.

This section provides steps required to install an IQ-NCC

and connect the required cables. The steps apply to all types
of cartridges with any differences explained separately.
Access Controller Cabinet
A Unlock and open the outer door of the ESP-LX Series
Controller.

B To open the controller front panel; grasp the crescent-

shaped handle on the right-hand side of the front
panel.
3

8 IQ Network Communication Cartridge

Remove the Communication Cable Knock-out
A Locate the IQ Port communication cable knock-out
on the bottom left of the controller case, next to the
transformer junction box.

B If a CM connection module will be installed for IQNet

communication, locate the rear knock-out for the IQNet
communication cable.

C Using a screwdriver or other pointed tool, center the

point of tool on the “dimple” in the center of the knock-
out, punch through and remove the cable knock-out(s).
CAUTION: Always wear eye protection when using
dd
tools or power equipment. 1 2

IQ Network Communication Cartridge 9

Install an External Antenna for LXMM B Using a screwdriver or other pointed tool, center
the point of tool on the “dimple” in the center of the
If the LXMM Metal Case is used along with the a NCC-GP
knock-out, punch through and remove the antenna
or NCC-WF cartridge, then an external antenna must be
knock-out hole located on the top right of the ESP-LX
installed in place of the internal antenna provided. These
controller plastic case.
external antennas are not included with the NCC and must
be purchased separately.
2
A Using a power drill and 5/8” (16 mm) drill bit, drill
a hole through the “dimple” on the top right of the
LXMM metal case.
CAUTION: always wear eye protection when using
dd
tools or power equipment.
1

10 IQ Network Communication Cartridge

C 
Follow the instructions which came with the LXMM to WARNING: To comply with FCC RF safety exposure
install the ESP-LX Series controller into the metal case. limits, the antenna used for this transmitter must be
installed to provide a separation distance of at least
D Route the antenna cable through the knockouts on top
20 cm from all persons and must not be located or
of the metal case and the controller. Set the antenna
operating in conjunction with any other antenna or
into the hole and secure from the inside as shown,
transmitter.
using the washers and nut provided.

IQ Network Communication Cartridge 11

Install the Cartridge C Connect the CM Port cable to the cartridge that applies
to the intended configuration (see Fig. 4). Two CM Port
A Press down on the top-latch of the cartridge bay cover
cables are included in the box with each cartridge,
and remove it from the back of the front panel.
one straight cable and one Y-cable. The cable that is
1 required depends on the controller configuration:
ll If the satellite is a Server or Client that will use a radio
modem for wireless communications with other satellites
on the IQNet, then install the Y-cable. The Y-cable plugs
directly into the radio modem (see user manual that comes
with radio modem for installation and configuration
instructions).
ll If the satellite is a Server or Client that will use a wired
connection (IQNet PE Communication Cable) to
communicate with other satellites, install the straight
cable.
ll If the satellite is a Server or Client that will use a radio
B Connect the IQ Port cable or antenna to the cartridge module for wireless communications AND a wired
(see Fig. 4). This cable or antenna provides the connection (IQNet PE Communication Cable) to
communication to the IQ computer. communicate with other satellites, install the Y-cable.
ll If the satellite is Direct (with no wireless or wired

NOTE: The cable for the NCC-RS cartridge has a DB9
connector that will not fit through the knockout. Route connection to another satellite) no CM Port cable is
the small end of the cable through the bottom of the necessary.
knockout first, then connect to the IQ Port.

12 IQ Network Communication Cartridge

CM Port Cables

CM Y-Cable (black)

CM Straight Cable (black)

CM Port
IQ Port Cables IQ Port
RS-232 External Modem Cable (Beige)

RJ-11 Phone Cord (Silver)

IQ Network
Communication
RJ-45 Ethernet Cable (Green) Cartridge
(IQ-NCC)
GPRS Cellular Internal Antenna (Gold)
Align Arrows
on Cable and
WiFi Internal Antenna (Gold) Housing for
Correct Fitting
Figure 4 - Installation/ Cable Options

IQ Network Communication Cartridge 13

 E
NOTE: The Y-cable has a DB9 connector that will not Orient the cartridge so that the two bottom hinges fit
fit through the knockout. Route the small end of the into the hinge openings at the bottom of the cartridge
cable through the bottom of the knockout first, then bay. Then gently swing the IQ-NCC up into place,
connect to the CM Port. snapping the top latch.


NOTE: The IQ-NCC-GP cartridge requires a SIM card
and GPRS/cellular telemetry service account that is
not provided and must be purchased separately. See
the SIM Card Installation section in the Appendix for
details.

D Connect the cartridge ribbon cable to the card-edge

connector located at the top left of the cartridge bay.
CAUTION: Ensure that the RED edge of the ribbon
dd
cable is towards the LEFT side of the connector.

14 IQ Network Communication Cartridge

Complete Cable Connections B If installing the NCC-PH cartridge, connect the Green
and yellow ground wire to the grounding post on the
A Route all cables from the cartridge through the channel
left side of the controller backplane.
in back of the front panel.

1 2

IQ Network Communication Cartridge 15

C For NCC-PH and NCC-EN cartridges, route the IQ D If required, install the type of Connection Module in
computer connection cable through the knockout in Slot 0 that is necessary for the intended configuration.
the lower left of the unit.

NOTE: If the satellite is being configured as a
Server or a Client with a wired connection (IQNet PE
Communication Cable) to another satellite, either
an IQ-FSCM-LXME (for the ESP-LXME) or an IQ-CM-
LXD (for the ESP-LXD) connection module must be
installed before proceeding. Refer to the Connection
Modules section of the Appendix for details. If no
wired connection is required, retain the base module
that was shipped with the controller. (The ESP-LXD
3 does not ship with a base module.)


NOTE: The NCC-RS cartridge has three connection
options to the IQ computer- External Modem, Direct E If a CM Port cable (Y-cable or straight) is installed,
connect the keyed mating connector to the FSCM/CM
Connect or IQSSRADIO. The RS-232 External Modem connection module as shown.
cable that ships with the cartridge has a male DB9


connector that plugs directly into an external modem. NOTE: The Y-cable may be used for a radio modem
If the Direct Connect or IQSSRADIO option is required, wireless connection only. If a connection module is not
use the black direct connect cable provided with the used, secure the unused cable end inside the satellite
IQ software package and sold separately to make the controller.
connection to the IQ computer or IQSSRADIO.
F To establish a wired connection with another satellite,
CAUTION: Do not plug a phone cable into the NCC- route one end of an IQNet PE Communication Cable
dd EN Ethernet cartridge. This will damage the internal through the knock-out on the bottom of the controller,
Ethernet modem. and attach the conductors to the blue terminals on the
FSCM/CM connection module as shown.
16 IQ Network Communication Cartridge
 CAUTION: Ensure that all installed cables inside the
dd
satellite do not contact the transformer directly, as heat
from the transformer may cause damage to a cable.

6
FSCM shown

G Secure all cables inside the controller and close the

front panel.

IQ Network Communication Cartridge 17

Internal Antenna Installation GPRS Cellular Back-plane
Antenna
Cellular (NCC-GP) and WiFi (NCC-WF) cartridges require
installation of an internal antenna (if not using LXMM). To
install the internal antenna(s):

A Clean surface to remove any dust or dirt.

B Remove the adhesive backing cover strip from the

GPRS Cellular or WiFi internal antenna.

C Place antenna in close proximity to back-plane as

shown, to allow ample clearance for the front panel to
close without pinching the antenna cable.


WARNING: To comply with FCC RF safety exposure
limits, the antenna used for this transmitter must be
installed to provide a separation distance of at least
20 cm from all persons and must not be located or
operating in conjunction with any other antenna or
transmitter.
CAUTION: Take special care the first time when
dd
placing the antenna. Once installed it cannot be easily
removed again.
GPRS Cellular Internal Antenna Installation

NOTE: Internal antennas must be installed in a vertical
position as shown to ensure maximum signal strength.

18 IQ Network Communication Cartridge

WiFi Antenna Back-plane

WiFi Internal Antenna Installation

IQ Network Communication Cartridge 19

IQ-NCC Configuration A The IQ Settings main menu is C The Setup – Satellite Address
displayed. Use the UP or DOWN screen is displayed. Direct
This section provides the steps arrows to select Setup Wizard; Satellites always have an address
required to configure an IQ-NCC for press Next. of 001; press Next.
communication with the IQ computer.
Follow the same steps for each type of
NCC Configurator Direct
IQ-NCC, any differences are addressed
in the specific step.
Direct Satellite Setup Wizard
Follow these steps to configure a
Direct Satellite:

B The Setup - Satellite Type screen D The Setup – Satellite IQ Port

gg
Turn the controller dial to
ETM/IQ SETTINGS. is displayed. Use + or - to select screen is displayed; press Next.
Direct; press Next. ll For RS Only: use + or - to choose
an IQ Port option, then press Next.

20 IQ Network Communication Cartridge


NOTE: The RS Cartridge
has three options, External
Modem, IQ Direct Connect, and
IQSSRADIO. All other cartridges
have only one option, either
Phone, GPRS/Cellular, Ethernet,
or WiFi modem depending on
the cartridge that is installed.

E The following message will be

displayed. Press Dismiss to exit
screen.
NCC Configurator

Dismiss

The Satellite is now ready to be

configured by the NCC Configurator
software.

IQ Network Communication Cartridge 21

Server Satellite Setup Wizard A The IQ Settings main menu is C The Setup – Satellite Address
Follow these steps to configure a displayed. Use the UP or DOWN screen is displayed. Server
Server Satellite: arrows to select Setup Wizard; Satellites always have an address
press Next. of 001; press Next.

gg
Turn the controller dial to
ETM/IQ SETTINGS.
NCC Configurator Server

B The Setup - Satellite Type screen D The Setup – Satellite IQ Port

is displayed. Use + or - to select screen is displayed; press Next.
Server; press Next. ll For RS Only: use + or - to choose
an IQ Port option, then press Next.

22 IQ Network Communication Cartridge

  
NOTE: The RS Cartridge NOTE: If the Y-cable is installed NOTE: If an IQ-FSCM-LXME
has three options, External for connection to a radio modem or an IQ-CM-LXD connection
Modem, IQ Direct Connect, and for wireless communication with module is installed for wired
IQSSRADIO. All other cartridges other satellites, choose Radio communications with other
have only one option, either Installed. satellites, choose Module
Phone, GPRS/Cellular, Ethernet, Installed.
or WiFi modem depending on F The Setup – Satellite CM Port
the cartridge that is installed.
screen is displayed. Use + or G The following message will be
- to select a CM Port option displayed. Press Dismiss to exit
E The Setup – Satellite Radio Port (No Module Installed, Module screen.
screen is displayed. Use + or - to Installed); press Next. NCC Configurator
select a radio port option (No
Radio Installed, Radio Installed);
press Next.
Dismiss

The Satellite is now ready to be

configured by the NCC Configurator
software.

IQ Network Communication Cartridge 23

Client Satellite Setup Wizard A The IQ Settings main menu is C The Setup – Satellite Address
Follow these steps to configure a displayed. Use the UP or DOWN screen is displayed. Use + or -
controller as a Client Satellite: arrows to select Setup Wizard; to select a unique address from
press Next. 002-256 for this satellite (press

gg
Turn the controller dial to and HOLD buttons to accelerate
ETM/IQ SETTINGS. settings); press Next.
NCC Configurator

Client

B The Setup - Satellite Type screen

is displayed. Use + or - to select
Client; press Next. D The Setup – Satellite Radio Port
screen is displayed. Use + or - to
select a radio port option (No
Radio Installed, Radio Installed);
press Next.

24 IQ Network Communication Cartridge

  NCC Configurator
NOTE: If the Y-cable is installed NOTE: If an IQ-FSCM-LXME
for connection to a radio modem or an IQ-CM-LXD connection
for wireless communication module is installed for wired Software
with the server, choose Radio communications with other Software configuration is performed
Installed. satellites, choose Module after installation and configuration
Installed. of the IQ-NCC cartridge is complete.
E The Setup – Satellite CM Port
Software configuration is only required
screen is displayed. Use + or - F The Setup – CM Port Termination
for Direct and Server Satellites. Consult
to select a CM Port option (No screen is displayed. Use + or - to
the NCC Configurator Software for
Module, Module Installed); press select a CM Port Termination
instructions.
Next. option (On or Off ).


NOTE: CM Port termination
is only required if this satellite
is at the end of an IQNet PE
Communication Cable path. If
you are not sure, consult with
the system designer.

IQ Network Communication Cartridge 25

Operation
This section provides LED indications and front panel
menu options that can be used to verify proper cartridge
installation, operation, and configuration. LED
Lights
Controls and Indicators Reset
Reset Button Button
The cartridge Reset button restarts the internal
programming and re-enables communications with the IQ
Central Computer without affecting configuration settings.
LED Indicators
The three LED lights on the front of each cartridge indicate
the status of each communication port on any satellite
controller. The meaning of each LED state is provided in the
following tables.
IQ Network Communication
Cartridge (IQ-NCC-RS shown)

26 IQ Network Communication Cartridge

 LED State NCC-RS Status NCC-PH Status NCC-EN Status NCC-GP Status NCC-WF Status
Dark Port disabled Port Disabled Port Disabled Port Disabled Port Disabled
Solid Red N/A Extension in use Connected to active No SIM card installed Connected to active
network (default IP network (default IP
address) address) or SSID
Blinking Red No IQ computer On hook, no voltage No connection to No RF signal from cell No connection to access
connection/no radio detected cable/switch tower point
modem detected
Solid Yellow IQ computer On hook, live line Connected to active Connected to cell tower Connected to active
connection/radio network and has valid network and has valid
modem detected, not IP address, but not IP address, but not
connected to IQ authenticated authenticated
Blinking Yellow Connecting with IQ Off hook, answering, Receiving data but Receiving data but not Receiving data but not
but has not completed dialing not authenticated authenticated authenticated
authentication
Solid Green Authenticated with IQ Authenticated with IQ Authenticated with IQ Authenticated with IQ Authenticated with IQ
but no data is being but no data is being but no data is being but no data is being but no data is being sent/
sent/received sent/received sent/received sent/received received
Blinking Green Authenticated with IQ Authenticated with Authenticated with Authenticated with IQ Authenticated with IQ
and data is being sent/ IQ and data is being IQ and data is being and data is being sent/ and data is being sent/
received sent/received sent/received received received
Blinking Red/Yellow Reflash or Reset Reflash or Reset Reflash or Reset Reflash or Reset Reflash or Reset
(sync all 3 LED’s)
Table 1 - IQ Port LED Indicators

IQ Network Communication Cartridge 27

 Connection Module Status LED State Radio Modem Status
LED State
(CM or FSCM) Dark Port disabled (also dark if configured
Dark Port disabled (also dark if configured as Client or No Radio Installed option
as Client or No Module Installed option selected in Setup Wizard)
selected in Setup Wizard) Solid Red N/A
Solid Red N/A Blinking Red No radio modem detected
Blinking Red N/A Solid Yellow N/A
Solid Yellow N/A Blinking Yellow N/A
Blinking Yellow Attempting to auto-BAUD or auto-polarity Solid Green Radio modem detected, but no data is
Solid Green Valid BAUD and polarity, but no data is being sent/received
being sent/received
Blinking Green Radio modem detected, data is being
Blinking Green Data is being sent/received sent/received
Blinking Red/Yellow Reflash or Reset Blinking Red/Yellow Reflash or Reset
(sync all 3 LED’s) (sync all 3 LED’s)
Table 2 - CM Port LED Indicators Table 3 - Radio Port LED Indicators

 
NOTE: The CM Port LED on Server Satellites and NOTE: The Radio Port LED on Server Satellites and
Client Satellites with both an IQNET Radio and CM Client Satellites with both an IQNET Radio and CM
Connection Module installed will continue to flash Connection Module installed will continue to flash
green as it searches for Client Satellites. green as it searches for Client Satellites.

28 IQ Network Communication Cartridge

Status Menu Direct Satellite Controllers A The IQ Settings main menu is
RS-232, Phone or Ethernet displayed. Use the UP or DOWN
The Status Menu is used to display the arrows to select Status; press
status of each communication port on To display the status of Direct
Next.
the front panel LCD. Satellites with IQ-NCC-RS, IQ-
NCC-PH, or IQ-NCC-EN cartridges IQNCC-XX Cartridge
For Direct and Server Satellites with a Setup Wizard
installed: NCC Configurator
NCC-GP or NCC-WF cartridge installed, Status

gg
the signal strength between the IQ Turn the controller dial to IQNet Alarms
computer and the controller can be ETM/IQ SETTINGS
displayed.
Server Satellites can use the Ping
feature to verify communication with
any user-selected Client Satellite. B The Satellite Status screen is
displayed. Current status of IQ,
Radio, and CM ports are shown.

IQ Network Communication Cartridge 29

Direct Satellite Controllers A The IQ Settings main menu is C The Signal Strength screen is
GPRS or WiFi displayed. Use the UP or DOWN displayed. The signal strength
arrows to select Status; press between the satellite and the
To display the status of Direct
Next. GPRS or LAN network is indicated
Satellites with IQ-NCC-GP or IQ-NCC-
on a scale from 1-10.
WF cartridges installed:
NCC Configurator
gg
Turn the controller dial to
ETM/IQ SETTINGS

B The Satellite Status screen is

displayed. Current status of IQ,
Radio, and CM ports are shown.
Press Signal to display GPRS or
WiFi signal strength.

30 IQ Network Communication Cartridge

Server Satellite Controllers A The IQ Settings main menu is C The IQNet Ping screen is
RS-232, Phone or Ethernet displayed. Use the UP or DOWN displayed. Use the + and -
arrows to select Status; press buttons to select any Client
To display the status of Server
Next address. Press Ping to check the
Satellites with IQ-NCC-RS, IQ-
communication status.
NCC-PH, or IQ-NCC-EN cartridges
installed: NCC Configurator

gg
Turn the controller dial to
ETM/IQ SETTINGS

B The Satellite Status screen is

The LCD will display Response-
displayed. Current status of
IQ, Radio, and CM ports are Yes if the ping is successful, or
shown. Press Ping to check the No for an unsuccessful ping.
communication status with The amount of time until the
selected Clients. response was received from
the server satellite is listed in
milliseconds.

IQ Network Communication Cartridge 31

Server Satellite Controllers A The IQ Settings main menu is C The Signal Strength screen is
GPRS or WiFi displayed. Use the UP or DOWN displayed. The signal strength
arrows to select Status; press between the satellite and the
To display the status of Server
Next. GPRS or LAN network is indicated
Satellites with IQ-NCC-GP or IQ-NCC-
on a scale from 1-10.
WF cartridges installed:
NCC Configurator
gg
Turn the controller dial to
ETM/IQ SETTINGS

B The Satellite Status screen is

displayed. Current status of IQ, D The Satellite Status screen is
Radio, and CM ports are shown. displayed. Press Ping to check
Press Signal to display GPRS or the communication status with
WiFi signal strength. selected Clients.

32 IQ Network Communication Cartridge

E The IQNet Ping screen is Client Satellite Controllers A The IQ Settings main menu is
displayed. Use the + and - To display the status of Client displayed. Use the UP or DOWN
buttons to select any Client Satellites with any cartridge arrows to select Status; press
address. Press Ping to check the installed: Next.
communication status.

gg
Turn the controller dial to
ETM/IQ SETTINGS NCC Configurator

The LCD will display Response-

B The Satellite Status screen is
displayed. Current status of IQ,
Yes if the ping is successful, or Radio, and CM ports are shown.
No for an unsuccessful ping.
The amount of time until the
response was received from
the client satellite is listed in
milliseconds.

IQ Network Communication Cartridge 33

IQNet Alarms Menu A The IQ Settings main menu is C If there is a communication
displayed. Use the UP or DOWN failure between the Server
The IQNet Alarms Menu is used to arrows to select IQNet Alarms; Satellite and Client Satellites,
display communication failures press Next. the IQNet Alarm screen will be
between the Server and Client displayed on the Server Satellite.
Satellites. Use the UP or DOWN arrows to
NCC Configurator
To Display Alarms: view other alarms.
IQNet Alarm 1
gg
03:45AM
Turn the controller dial to 05 JAN 2010
IQ SETTINGS. Can’t Communicate
with Satellite XXX
Sensor and MV Sharing
may be off-line

B If there are no alarms, the

following screen is displayed.
03:45AM
05 JAN 2010

34 IQ Network Communication Cartridge

D If there is a communication
failure between a Client Satellite
and the Server Satellite, the
IQNet Alarm screen will be
displayed on the Client Satellite.
Use the UP or DOWN arrows to
view other alarms.
03:45AM
05 JAN 2010

E On either IQNet Alarm screen,

press Clear to clear all alarms.
Press Yes to confirm.

IQ Network Communication Cartridge 35

Appendix
Connection Modules Base Module Flow Smart Module
The BM-LXME Base Module is the The optional FSM-LXME Flow Smart
Connection Module Options default module that comes with an Module used in an ESP-LXME controller
There are four different types of ESP-LXME controller. This module can can be used with an IQ-NCC when
connection modules that may be be used with an IQ-NCC when wired wired communications with other
installed in Slot 0 of the ESP-LX Series communications with other satellites satellites is not required.
Controller. is not required.
The type of connection module that
is required for installation of an IQ
Network Communication Cartridge
depends on the type of controller
(ESP-LXME or ESP-LXD) and on the
type of communication required with
other satellites (wired or wireless).

36 IQ Network Communication Cartridge

 
IQ Connection Module IQ Flow Smart Connection Module NOTE: See the ESP-LXME Con-
If wired communications (IQNet PE If wired communications (IQNet PE troller manual for instructions
Communication Cable) is required Communication Cable) is required on configuring the Flow Smart
between an ESP-LXD satellite and other between an ESP-LXME satellite and Module.
satellites, an IQ-CM-LXD Connection other satellites, an IQ-FSCM-LXME
Module must be installed in the ESP- Connection Module must be installed
LXD satellite to make the connection. in the ESP-LXME satellite to make the
connection.

IQ Network Communication Cartridge 37

Connection Module Installation B Orient the connector on the bottom of the IQ-FSCM-
LXME or IQ-CM-LXD module with the connection
Follow these steps if a connection module is required for
socket on the satellite backplane.
IQNet wired communications:

A To remove an existing base module, press in on the C Carefully fasten the module onto the satellite
backplane, pressing firmly until it snaps into place.
two release buttons on each end of the module to
release it from slot 0.


NOTE: The ESP-LXD does not ship with a base module.
Remove the black plastic cover on the backplane in
slot 0 to reveal the pins on the connector.
2

38 IQ Network Communication Cartridge

D Connect the Green and yellow ground wire to the
grounding post on the left side of the satellite
backplane.


NOTE: If the ground wire from an IQ-NCC-PH cartridge
has been previously installed on the grounding post,
disconnect the wire. Connect the connection module
ground wire directly to the post, then reconnect the
IQ-NCC-PH ground wire to the connection module
ground connector.

IQ Network Communication Cartridge 39

Connect IQ-CM Grounding Wire
An additional ground wire is required if you’re installing
either an IQ-CM-LXD or IQ-CM-LXME connection module.

A Attach one end of the grounding wire to Earth ground

(electrical ground, ground rod or ground plate).
3
B Route the grounding wire through the knock-out on
the bottom of the controller.

C Attach the grounding wire to the CM module GND

terminal as shown.


WARNING: Failure to ensure proper grounding of
the connection module could result in risk of electric
shock or other hazard to persons, as well as possible
equipment damage and malfunction.

2
1 To Earth ground

40 IQ Network Communication Cartridge

SIM Card Installation B Orient the SIM card to match the image of the SIM card
as displayed molded on the cartridge (with the “cut-
The GPRS/Cellular Network Communication Cartridge (IQ- corner” on top and to left as shown).
NCC-GP) requires a SIM card to establish a connection with
a public static IP address. C Install the SIM card in the slot.


NOTE: An IP address must be obtained from AT&T 2
or another GSM/GPRS service provider, and must be
purchased separately.
Follow these steps to install a SIM card in the NCC-GP:

A On the front of the NCC-GP, remove the T-shaped 3

access plate by pressing down on the tab.

D Replace the access plate.

Regulatory Information EMC Requirements for Industry Canada
This product meets the applicable Industry Canada technical specifications
EMC Requirements for the United States
This Class B digital apparatus meets all requirements of the Canadian Interference-
This equipment has been tested and found to comply with the limits for a Class Causing Equipment Regulations.
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
Cet appareil numérique de la classe B respecte toutes les exigences du Reglement
to provide reasonable protection against harmful interference in a residential
Canadien sur le matériel brouilleur.
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if Requirements for the South Africa
not installed and used in accordance with the instructions, may cause harmful This modem must be used in conjunction with an approved surge protection
interference to radio communications. However, there is no guarantee that device (applies to PH cartridge only).
interference will not occur in a particular installation.
If the equipment does cause harmful interference to radio or television reception, Analog Telecom Safety Warnings
which can be determined by turning the equipment off and on, the user is Applies to PH cartridge only:
encouraged to try to correct the interference by the following measures: 1. Never install telephone wiring during a lightning storm.
 Reorient or relocate the receiving antenna. 2. Never install a telephone jack in wet locations unless the jack is specifically
 Increase the separation between the equipment and the receiver. designed for wet locations.
 Connect the equipment into an outlet on a circuit different from that to 3. This product is to be used with UL and cUL listed computers.
which the receiver is connected.
4. Never touch uninsulated telephone wires or terminals unless the telephone
 Consult the dealer or an experienced radio/TV technician for help. line has been disconnected at the network interface.
This device complies with 47 CFR – FCC Part 15 rules. Operation of this device is
5. Use caution when installing or modifying telephone lines.
subject to the following conditions:
1. This device may not cause harmful interference, and 6. Avoid using a telephone during an electrical storm. There may be a remote
risk of electrical shock from lightning.
2. This device must accept any interference that may cause undesired
operation. 7. Do not use a telephone in the vicinity of a gas leak.
This product was FCC certified under test conditions that included the use 8. To reduce the risk of fire, use only 26 AWG or larger telecommunication line
of shielded I/O cables and connectors between system components. To be cord.
in compliance with FCC regulations, the user must use shielded cables and 9. This product must be disconnected from its power source and telephone
connectors and install them per instructions. network interface when servicing.
WARNING: Changes or modifications not expressly approved by Rain Bird
Corporation could void the user’s authority to operate the equipment.
The wireless carrier will require the device’s IMEI (International Mobile Equipment
Identity) number. This IMEI number is printed on the label on the backside of the
modem cartridge.

Complies with 47 CFR Part 68.

Reg. No: US:AU7MM01BMT5692SMI
REN: 0.1B
 RAIN BIRD CORPORATION
6991 E. Southpoint Road
Tucson, AZ 85756

Copyright © 2010 by Rain Bird Corporation. All rights reserved.

This material may not be published or reproduced without permission.

“Rain Bird” and “IQ Central Control System”

are registered trademarks of Rain Bird Corporation.

www.rainbird.com

12/10 P/N: 638085-01