Z/A/X/DZ Common Accessories
Ordering Information
■ Terminal Covers (Sold Separately)
Common to Z, A, X, and DZ Models
The Terminal Cover is secured using the switch’s side mounting screws and protects the casing and terminal wires from dust, vibration, or fingers,
thus preventing terminal short-circuiting, ground faults, wire disconnection or improper connection, and electric shock accidents.
Terminal Covers made of phenol resin have five or six thin wall sections.
These sections can be torn open to provide holes for lead cables at desired points.
Application Soldering terminal use Screw terminal use
Remarks
Material Mounting direction Model
Phenol resin Side mounting AP-A AP-B ---
Metal press mold Side mounting AP1-A AP1-B Used for AP-A and AP-B
Vinyl chloride Side mounting AP-Z ---
Note: Use the ‘Screw-terminal use’ Terminal Cover for DZ-series solder terminal models.
■ Separator (Sold Separately)
Common to Z, A, X, and DZ Models
Model: Separator for Z
■ Actuators (Sold Separately)
Common to Z and X Models
Pin Plunger Switches might need to be actuated by a cam or similar object, in which case, use one of the following Actuators according to the application.
Actuator Common to Z and X models
Hinge lever
ZAA-1
Hinge roller lever
ZAA-2
Panel mount plunger Short ZAQ-3
Medium ZAQ-2
Long ZAQ-1
Panel mount roller plunger
ZAQ-22
Note: ZAQ-22 is constructed of ferrous material. Therefore, it cannot be used with the X Switch, because of the permanent magnet contained
within those models. Use the ZAQ-22 external panel mount roller plunger only with the Z or DZ switch.
Z/A/X/DZ Common Accessories 177
Dimensions
Note: Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm (±0.8 mm for the AP-Z) applies to all dimensions.
■ Terminal Covers
52.8 53.8
AP-A AP-B 4.3+0.2 25.4 4.3 +0.2
4.3+0.2 25.4 4.3 +0.2 0 0
Soldering Terminal Use 0 0
Screw Terminal Use
(Phenol Resin) 8
(Phenol Resin) 8
16.3 20.2
2.15R
2.15R 6.4
6.5
8 21
8 21
Note: The Cover has five thin, easy-to-separate Note: The Cover has six thin, easy-to-separate
portions for easy lead wire connections. portions for easy lead wire connections.
54.4
AP1-A 25.4 AP1-B 55.4
4.3+0.2
0 4.3 +0.2
0 4.3+0.2 25.4 4.3 +0.2
Soldering Terminal Use Screw Terminal Use
0 0
(Metal Press Mold) 8 (Metal Press Mold) 8
17.1
2.15R 2.15R 21
7.2
7
8.5 22.6
8.5 22.6
Note: 1. The Cover has five holes for easy lead wire connections. Note: 1. The Cover has six holes for easy lead wire connections.
2. AP1-A should be used with the AP-A 2. AP1-B should be used with the AP-B
AP-Z Pressure plate
Two, 4.2 dia.
Soldering or Screw Terminal Use (t1 steel) 53
(Vinyl Chloride) 21 25.4 Cable Pull-out Dimension
7
14
A-A' cross-section B-B' cross-section
21 15 8 dia. 13 6 dia.
39
46
Note: A 6-dia. or 8-dia. cable can be
used by cutting the cable pull-out
hole to the size of the cable to be
A A' used.
B B'
12 M3 20 Phillips screw 12
Nut
14 (with plane washer and nut)
■ Separator
SEPARATOR FOR Z
Two, 4.5 dia.
Note: The separator’s material is EAVTC (Epoxide Alkyd
13.5 Varnished Tetron Cloth) and its heat-resisting
27
temperature is 130°C.
11.9
25.4±0.2
49.2±0.5 t = 0.38
178 Z/A/X/DZ Common Accessories
■ Actuators
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm applies to all dimensions.
2. These Actuators are not provided with Switches.
Hinge Lever Two, M4 30
ZAA-1 Two, M4
Model Z-15G-B X-10G-B
OF max. 500 gf 500 gf
RF min. 170 gf 170 gf
PT max. 6 mm 6 mm
Stainless steel OT min. 12.7 mm 12.7 mm
60R MD max. 2.2 mm 3.3 mm
FP max. 32.9±1.6 mm
Note: This Actuator can be used with the Z-15G(-B)
and X-10G(-B). When mounting the Switch, set
the overtravel to between 32% and 100%, taking
into consideration the operating body and the dis-
tance between the Actuator and the dog.
Hinge Roller Lever Two, M4 Two, M4 30
ZAA-2
Model Z-15G-B X-10G-B
OF max. 500 gf 500 gf
RF min. 170 gf 170 gf
9.5 dia. 4.8
PT max. 6 mm 6 mm
(stainless-steel roller) OT min. 12.7 mm 12.7 mm
Stainless steel
MD max. 2.2 mm 3.3 mm
58.5R
FP max. 44.5±1.6 mm
Note: This Actuator can be used with the Z-15G(-B)
and X-10G(-B). When mounting the Switch, set
the overtravel to between 32% and 100%, taking
into consideration the operating body and the
distance between the Actuator and the dog.
Panel Mount Roller Lever 48 12.7 dia. (Note 1)
ZAQ-22 PT 23.3±0.25 4.8
Two hex nuts
5-mm thickness, 19 mm Model ZAQ-22
between opposing edges Z-15E-B DZ-10G-B
With groove for roller
OP
penetration OF max. 850 gf 1,131 gf
(Note 3) M12 1 mounting RF min. 114 gf 114 gf
1.6 18.9 screw
14.5 PT max. 2 mm 2 mm
dia.
OT min. 3.58 mm 1 mm
20.7 23.9 MD max. 0.15 mm 0.46 mm
OP 37±0.8 mm 35.4±1.2 mm
Note: This Actuator (panel mount roller
Spring washer
plunger) can be used with
(Note 2) 25.4±0.2 Two, M4 25 20.7 standard pin plungers (Z-15G(-B),
11.9 screws
49.2 Z-15E(-B), and DZ-10G-1A(-1B)).
The ZAQ-22 is constructed of
Note: 1. Stainless-steel pin plunger ferrous material. Therefore, It
2. Bronze frame cannot be used with X switches
due to the permanent magnet used
3. Incomplete screw section part within those models.
with a maximum of 1.5 mm.
Z/A/X/DZ Common Accessories 179
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ± 0.4 mm applies to all dimensions.
2. These Actuators are not provided with Switches.
Short Panel Mount Plunger
ZAQ-3 7.9 dia. Model ZAQ-3
23.3
12SR Z-15E-B X-10G-B
(Note 1) M12 1 mounting
screw
OF max. 850 gf 550 gf
2 t 14 width across
flats RF min. 114 gf 114gf
(Note 3) PT max. 0.8 mm 1 mm
14.5
dia. OT min. 4.8 mm 4.5 mm
2 t 15.6 width
across flats MD max. 0.15 mm 0.2 mm
Two M4 nuts OP 27.8±1.5 mm
Note: 1. Stainless-steel pin plunger
2. Bronze frame
3. Incomplete screw section part
Two M4 25 ± round
with a maximum of 1.5 mm
(Note 2)
head screw
Medium Panel Mount Plunger
ZAQ-2 7.9 dia. Model ZAQ-2
23.3
12SR M12 1 mounting
Z-15E-B X-10G-B
(Note 1) screw
OF max. 850 gf 550 gf
2 t 14 width across
flats RF min. 114 gf 114 gf
PT max. 0.8 mm 1 mm
OT min. 4.8 mm 4.5 mm
2 t 15.6 width
across flats MD max. 0.15 mm 0.2 mm
14.5
(Note 3)
dia. OP 53.2±1.5 mm
Note: 1. Stainless-steel pin plunger
Two M4 25
screw
2. Bronze frame
3. Incomplete screw section part
with a maximum of 1.5 mm
Two M4 nuts
(Note 2)
Long Panel Mount Plunger
ZAQ-1
7.9 dia. Model ZAQ-1
23.3
12SR Z-15E-B X-10G-B
(Note 1)
OF max. 850 gf 550 gf
M12 1 mounting RF min. 114 gf 114 gf
screw
PT max. 0.8 mm 1 mm
2 t 14 width across
flats OT min. 20.6 mm 20.4 mm
MD max. 0.15 mm 0.2 mm
OP 69.1±1.5 mm
2 t 15.6 width
across flats Note: 1. Stainless-steel pin plunger
(Note 3) 14.5
dia. 2. Bronze frame
3. Incomplete screw section part
Two, M4 25 screws with a maximum of 1.5 mm
(Note 2) Two, M4 nuts
Note: Except for the ZAQ-22, these actuators (panel mount plungers) can be used with standard pin plunger versions of the Z and X models.
(Z-15G(-B), Z-15E(-B), X-10G(-B))
180 Z/A/X/DZ Common Accessories
MEMO
Z/A/X/DZ Common Accessories
All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which
can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ELECTRONIC OMRON ON-LINE
COMPONENTS LLC Global - http://www.omron.com
55 E. Commerce Drive, Suite B USA - http://www.components.omron.com
Schaumburg, IL 60173
847-882-2288
Cat. No. X303-E-1 11/10 Specifications subject to change without notice Printed in USA
Z/A/X/DZ Common Accessories
