VANIN

Wi-Fi 6 Mesh Router

Juplink RX4-1500
User Manual v 1.0.4

1
About This Guide ....................................................................................................................... 4

Chapter 1 Get to Know About Your Router............................................................................... 5

1. 1. Product Overview .......................................................................................................... 6

Chapter 2 Connect the Hardware ............................................................................................. 8

2. 1. Position Your Router...................................................................................................... 9

2. 2. Connect Your Router ..................................................................................................... 9

Chapter 3 Log In to Your Router.............................................................................................. 11

Chapter 4 Set Up Internet Connection.................................................................................... 13

4. 1. Manually Set Up Your Internet Connection ................................................................ 14

4. 2. Set Up the Router as an Access Point .......................................................................... 16

4. 3. Set Up an IPv6 Internet Connection ............................................................................ 17

Chapter 5 Guest Network ....................................................................................................... 19

5. 1. Create a Network for Guests ....................................................................................... 20

Chapter 6 Security Set –WAN Access Control, Parent Control, Wireless Filter ...................... 21

6. 1. WAN Access Control .................................................................................................... 22

6. 2. Parental Controls ......................................................................................................... 23

6. 3. Wireless Filter .............................................................................................................. 24

Chapter 7 VPN Server .............................................................................................................. 25

7. 1. L2TP VPN...................................................................................................................... 26

Chapter 8 Customize Your Network Settings .......................................................................... 27

8. 1. QoS .............................................................................................................................. 28

8. 2. Bridge mode ................................................................................................................ 29

8. 3. Change the LAN IP address .......................................................................................... 29

8. 4. Address reservation ..................................................................................................... 30

8. 5. Specify DHCP Server Settings ...................................................................................... 31

8. 6. Specify Wireless Settings ............................................................................................. 31

8. 7. Use Repeater to Extend Network ................................................................................ 35

8. 8. LAN Port Forwarding ................................................................................................... 36

8. 9. Dual frequency ............................................................................................................ 36

8. 10. WIFI Roaming............................................................................................................. 37

2
 8. 11. Mesh .......................................................................................................................... 37

Chapter 9 Manage the Router ................................................................................................ 40

9. 1. Upgrade the Firmware ................................................................................................ 41

9. 2. Restore Default Setting ............................................................................................... 41

9. 3. Change the Login Password......................................................................................... 42

9. 4. System Log ................................................................................................................... 42

9. 5. Set up System Time ..................................................................................................... 43

FAQ .......................................................................................................................................... 44

3
About This Guide
This guide is a complement of Quick Installation Guide. The Quick Installation Guide
instructs you on quick internet setup, and this guide provides details of each function and
shows you the way to configure these functions appropriate to your needs.
When using this guide, please notice that features of the router may vary slightly depending
on the model and software version you have, and on your location, language, and internet
service provider. All screenshots, images, parameters and descriptions documented in this
guide are used for demonstration only.

*Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11
specifications. Actual wireless data throughput and wireless coverage are not guaranteed
and will vary as a result of network conditions, client limitations, and environmental factors,
including building materials, obstacles, volume and density of traffic, and client location.
*Use of MU-MIMO and 1024-QAM requires clients to also support those functions.

More Info
The latest software, management app and utility can be found at Download Center at
https://www.juplink.com/pages/juplink-rx4-1500-firmware-download-center
The Quick Installation Guide can be found where you find this guide or inside the package of
the router.
Specifications can be found on the product page at https://www.juplink.com.
2
Our Technical Support contact information can be found at the Contact Technical
Support page at https://www.juplink.com/ contact-us

4
Chapter 1

Get to Know About Your

Router
This chapter introduces what the router can do and shows its appearance.
It contains the following sections:
- Product Overview
- Panel Layout

5
1. 1. Product Overview
The VANIN Juplink router is designed to fully meet the need of Small Office/Home Office
(SOHO) networks and users demanding higher networking performance. The powerful
antennas ensure continuous Wi-Fi signal to all your devices while boosting widespread
coverage throughout your home, and the built-in Ethernet ports supply high-speed
connection to your wired devices.

1. 2. Panel Layout
1. 2. 1. Top View

1. 2. 2. Front View

6
LED Explanation
Solid Green -The router is starting to connect or has been successfully connected to the internet
Fast blinking -The router is performing WPS negotiation.
Off - Power is off or the LED is turned off.

1. 2. 3. The Side and Back Panel

Button Description
WPS Button - Press this WPS button, and immediately press the WPS button on your client device. The LED of the
router should change from pulsing white to solid on, indicating successful WPS connection.

7
Chapter 2

Connect the Hardware

This chapter contains the following sections:
- Position Your Router
- Connect Your Router

8
2. 1. Position Your Router
• The router should not be located in a place where it will be exposed to moisture or
excessive heat.
• Place the router in a location where it can be connected to multiple devices as well as to a
power source.
• Make sure the cables and power cords are safely placed out of the way so they do not
create a tripping hazard.
• The router can be placed on a shelf or desktop.
• Keep the router away from devices with strong electromagnetic interference, such as
Bluetooth devices, cordless phones and microwaves.

2. 2. Connect Your Router

Before you start, please turn off your modem if any. Hold the antennas from the base and
make the antenna vertical in the horizontal plane.
If your internet connection is through an Ethernet cable directly from the wall instead of
through a DSL / Cable / Satellite modem, connect the Ethernet cable to the router’s WAN
port, and then follow step 3 to complete the hardware connection.
1. Connect the modem to your router’s WAN port with an Ethernet cable.
2. Turn on the modem, and then wait about 2 minutes for it to restart.
3. Connect the power adapter to the router and turn on the router.
4. Verify that the LED is solid on before moving on.
5. Connect your computer to the router.

• Method 1: Wired
Turn off the Wi-Fi on your computer and connect your computer to the router with an
Ethernet cable.
• Method 2: Wirelessly
1) Find the SSID (Network Name) printed on the label at the bottom of the router.
2) Click the network icon of your computer or go to Wi-Fi Settings of your smart device, and
then select the SSID to join the network.

9
• Method 3: Use the WPS button
Wireless devices that support WPS, including Android phones, tablets, and most USB
network adapters, can be connected to your router through this method.
Note:
• WPS is not supported by IOS devices.
• The WPS function cannot be configured if the wireless function of the router is disabled. Also, the
WPS function will be disabled if your wireless encryption is WEP. Please make sure the wireless
function is enabled and is configured with the appropriate encryption before configuring the WPS.
1) Tap the WPS icon on the device’s screen. Here we take an Android phone for instance.
2) Within two minutes, press the WPS button on your router.

10
Chapter 3

Log In to Your Router

11
With a web-based utility, it is easy to configure and manage the router. The web-based
utility can be used on any Windows, Mac OS or UNIX OS with a web browser, such as
Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

Follow the steps below to log in to your router.

1) Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer.
2) Visit 192.168.0.1 or router.juplink.com
3) Enter the Username admin and Password admin then click Login (You can modify the
login password in Page Change the Login Password)

Note: -If the login window does not appear, please refer to the FAQ Section.

12
Chapter 4

Set Up Internet Connection

This chapter introduces how to connect your router to the internet. The router is equipped
with a web-based Quick Setup wizard. It has necessary ISP information built in, automates
many of the steps and verifies that those steps have been successfully completed.
Furthermore, you can also set up an IPv6 connection if your ISP provides IPv6 service.
It contains the following sections:
- Manually Set Up Your Internet Connection
- Set up the Router as an Access Point
- Set up an IPv6 Internet Connection

13
4. 1. Manually Set Up Your Internet Connection
In this part, you can check your current internet connection settings. You can also modify the
settings according to the service information provided by your ISP.
Follow the steps below to check or modify your internet connection settings. ( If you need
the IPv6 internet connection, please refer to the section of Set Up an IPv6 Internet
Connection )
4.1.1. If you choose DHCP, You can change your Wi-Fi network (2.4G SSID or 5G SSID) name
and password (2.4G SSID Network Key or 5G SSID Network Key)

4.1.2. If you choose PPPoE, enter the Username and Password provided by your ISP. PPPoE
users usually have DSL cable modems.

14
4.1.3. If you choose Static IP, enter the information provided by your ISP in the
corresponding fields.

4.1.4. When you have finished modifying and clicked the Continue button. You will jump to
the page that confirms the modification. (You can take a screenshot to keep this information
for the next time or for others to use) Click OK button Router will reboot and reconnect to your
device in a short time.

15
4. 2. Set Up the Router as an Access Point
The router can work as an access point, transforming your existing wired network to a
wireless one.
Before Installation Please complete the following settings:
1) After disconnecting the WAN port. Connect a device to your Juplink router and launch a
web browser. Then Log in to Your Router.
2) Click Network > LAN > IP Address .manually set IP address as the following format
192.168.0.XXX (XXX is any number of 2~254) leave the Subnet Mask as the default settings.
After Click Save/Apply button, you need reconnect the router and enter the address you set
to log in to the web UI instead of the default 192.168.0.1.

3) Connect the router to your existing wired router via an Ethernet cable as below sample.

16
4. 3. Set Up an IPv6 Internet Connection
Your ISP provides information about one of the following IPv6 internet connection types:
IPV6 (Auto Configured) ; IPV6 Static
4.3.1. IPV6 (Auto Configured)
1) After Log in to Your Router, Click Network > WAN > IP Mode (Select IPv6 from the drop
down menu) in the new menu that pops up, Switch IPv6 information to Auto Configured.
2) Click Save/Apply button to finish your setting.

17
4.3.2. IPV6 Static
1) After Log in to Your Router , Click Network > WAN > IP Mode (Select IPv6 from the drop
down menu) In the new menu that pops up, Switch IPv6 information to Static, then Fill in
information as required.
2) Click Save/Apply button to finish your setting.

18
Chapter 5

Guest Network
This function allows you to provide Wi-Fi access for guests without disclosing your main
network. When you have guests in your house, apartment, or workplace, you can create a
guest network for them.
It contains the following sections:
- Create a Network for Guests

19
5. 1. Create a Network for Guests
1) After Log in to Your Router, Click Network > Guest SSID >Enable
2) Set Authentication Mode to WPA-PSK/WPA2-PSK AES (recommended), and customize
your own password.

3) Click Apply to finish your setting. Now your guests can access your guest network using
the SSID and password you set.

20
Chapter 6

Security Set –WAN Access

Control, Parent Control,
Wireless Filter
Create a personalized network that caters for the whole family in Security Setting. You can
ensure appropriate internet access for everyone with Parent Control. keep your network
secure in WAN Access Control.
It contains the following sections:
- WAN Access Control
- Parental Controls
- Wireless Filter

21
6. 1. WAN Access Control
WAN Access Control is used to block or allow specific URL to access your network
(Via wired or wireless) based on a list of blocked devices (Blacklist) or a list of allowed
devices (Whitelist). Block or allow specific URL to access your network (via wired or
wireless).
1) After Log in to Your Router, Click Security > WAN Access Control > Select Black List click
Modify (recommended) or White List in URL Filter Type list, to block or allow specific Web
Site.
2) Fill in the URL Address you wish to block (or allow) access to your device, then click Add.

3) If you want to cancel the restrictions of this website. Check the URL then Click Delete

22
6. 2. Parental Controls
Parental Controls allows you to set up unique restrictions on internet access for each
member of your family. You can set daily limits for the total time spent online.
1) After Log in to Your Router, Click Status > LAN Device Copy LAN Devices MAC

2) Click Security > Parental Controls > Paste copied LAN Devices MAC in MACs Blank
Then select Date and fill in the Time.

Note: -Only devices that have previously been connected to your router’s network are listed here. If
you are unable to find the device you want to add, connect it to your network and then try again.

23
6. 3. Wireless Filter
Wireless Filter allows or denies wireless access to clients with the specified MAC addresses.
1) After Log in to Your Router, Click Status > LAN Device Copy LAN Devices MAC

2) Click Security > Wireless Filter

Select MAC Restrict Mode. Paste copied LAN Devices MAC in MAC Address Blank, then click
Add/Apply

24
Chapter 7

VPN Server
The VPN (Virtual Private Networking) Server allows you to access your home network in a
secured way through internet when you are out of home.
The router offers two ways to setup VPN connection: L2TP connection mode
- Use L2TP VPN to Access Your Home Network.

25
7. 1. L2TP VPN
1) After Log in to Your Router, Click Network > VPN
Fill in the corresponding information then click add.

26
Chapter 8

Customize Your Network

Settings
This chapter guides you on how to configure advanced network features.
It contains the following sections:
- QoS
- Bridge mode
- Change the LAN IP address
- Address reservation
- Specify DHCP Server Settings
- Specify Wireless Settings
- Use Repeater to Extend Network
- LAN Port Forwarding
- Dual frequency
- WIFI Roaming
- Mesh

27
8. 1. QoS
QoS (Quality of Service) allows you to prioritize the internet traffic of specific online
activities, such as gaming or streaming. Activities set as high priority will be allocated more
bandwidth and so continue to run smoothly even when there is heavy traffic on the network.
You can also prioritize the connection of specific devices for a set duration.
Note: This feature needs to be enabled before using.
1) After Log in to Your Router, Click Network > QoS > Click Enable QoS

2) Traffic Classification Settings: Create Egress Queue (Q1~Q8) new rule based on different
selection.

3) Set Queue scheduling: you can set your Queue base on Priority, Bandwidth Ratio,
Bandwidth (Kbps)

28
8. 2. Bridge mode
You can modify the working mode-Bridge of the router in this page.
Bridge mode - You can select Bridge if your ISP is not listed and no other parameters are
required.
After Log in to Your Router, Click Network > WAN > Connection Type

8. 3. Change the LAN IP address

The router is preset with a default LAN IP 192.168.0.1, which you can use to log in to its web
management page. The LAN IP address together with the Subnet Mask also defines the
subnet that the connected devices are on. If the IP address conflicts with another device on
your local network or your network requires a specific IP subnet, you can change it.
8.3.1 Change Login Address.
After Log in to Your Router, Click Network > LAN > IP Address .manually set IP address as the
following format 192.168.0.XXX (XXX is any number of 2~254) leave the Subnet Mask as the
default settings. After Click Save/Apply you need reconnect the router and enter the
address you set to log in to the web UI instead of the default 192.168.0.1.

29
8. 4. Address reservation
This function is used to assign a fixed IP address to your specific network device
1) After Log in to Your Router, Click Status > LAN Device Copy LAN Devices MAC
2) Click Network > LAN

Paste copied LAN Devices MAC in MAC Address Blank, assign an IP address.
Then click Add/Apply finish all setting.

30
8. 5. Specify DHCP Server Settings
By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router
acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP
Address Pool. You can change the settings of the DHCP Server if necessary, and you can
reserve LAN IP addresses for specified client devices.
8.5.1 To specify the IP address that the router assigns
1) After Log in to Your Router, Click Network > LAN > Enable DHCP Server
2) Change Start IP Address & End IP Address as you wish. The Click Save/Apply Button.

8. 6. Specify Wireless Settings

The router’s wireless network name (SSID) was preset in the factory. The preset SSID can be
found on the label of the router. You can customize the wireless settings according to your
needs.
8.6.1. To enable or disable the wireless function
1) After Log in to Your Router, Click Network > 2.4 G Wireless / 5 G Wireless
2) The wireless function is enabled by default. If you want to disable the wireless function of
the router, just untick the Enable checkbox of each Wireless network and click Apply button.
In this case, all the wireless settings will be invalid.

31
8.6.2. To change the wireless network name (SSID) and wireless password:
1) After Log in to Your Router, Click Network > 2.4 G Wireless / 5 G Wireless
2) Select Authentication (Mode WPA-PSK/WPA2-PSK is recommended)
3) Set your SSID (Wi-Fi name) and Key (Wi-Fi password) Click Apply button, you can
reconnect your Wireless network with new SSID and Key.

Note:- If you change the wireless settings with a wireless device, you will be disconnected when the
settings are effective. Please write down the new SSID and password for future use.

8.6.3. To change the wireless security option

1) After Log in to Your Router, Click Network > 2.4 G Wireless / 5 G Wireless
Select an option from the Encryption Mode and Encryption Mode drop-down list.

32
8.6.4. To enable or disable the wireless function
1) After Log in to Your Router, Click Network > 2.4 G Wireless / 5 G Wireless > Advanced
Setup
2) Hide SSID: Select it, your SSID won’t display when you scan for local wireless networks on
your wireless device and you need to manually join the network.

8.6.5. To change the 5G Wireless option:

1) After Log in to Your Router, Click Network > 5 G Wireless > Advanced Setup
2) Working Mode: Select Work mode in drop-down list (802.11a/n/ac/ax is recommended)

33
3) Channel: You can Select Wireless Channel in drop-down list (Auto is recommended)

4) Band Width: You can select a channel width (bandwidth) in drop-down list for the wireless
network (20MHz/40MHz/80MHz is recommended)

5) Transmit Power - Select 20% (Low), 40%, 60%, 80%, 100% (High) to specify the data
transmit power. The default setting is 100%.

Note: -We recommend you don’t change the default settings unless necessary. If you select other
options, please check whether your device supports this mode beforehand.

34
8. 7. Use Repeater to Extend Network
Extend your existing wireless network range with the repeater feature.

1) After Log in to Your Router, Click Application > Repeater

2) Click the Scan Wi-Fi button, wait about 5 seconds.
3) Select Enable & Sync with gateway (suggest)

4) Enter the password of the Wi-Fi that will be extended in Key blank.
5) Click Connect button, you can enjoy the extended Wi-Fi.

35
8. 8. LAN Port Forwarding
A virtual server is a server using a device on the LAN side, which can be accessed directly
from the external network.
1) After Log in to Your Router, Click Application > Virtual Server
2) Fill in the Outer Port, Client IP Address and Inner Port, choose Protocol Type in
drop-down list.
3) Click Add button to finish your setting.

8. 9. Dual frequency
Better signal connection scheme for your devices
1) After Log in to Your Router, Click Application > Dual frequency
2) Select Enable Dual frequency.

Note: - When Dual frequency is enabled, the SSID name, auth mode and auth key of 5G band will be
changed to the same as the 2.4G band;
- You can change the threshhold value according to the actual situation (Default values are
recommended)

36
8. 10. WIFI Roaming
Adjust signal threshold under AP connection
1) After Log in to Your Router, Click Application > WIFI Roaming
2) Changing according to your actual situation (Default values are recommended)

8. 11. Mesh
Mesh connection mode, can be quickly achieved via WPS button

1) Connect your router’s WAN port to the LAN port of the modem or Router (Main router)
3) Set up the router which has connected WAN port, enable it to access the Internet
normally (please note that the wireless network must be set to an encrypted state and
password has been set)
4) Press the WPS button on both routers for at least 5 seconds.
5) After about 30 seconds, Wait for the lights on both routers to change from flashing to
steady, and the setting is complete. it means that the Mesh is set and can be used normally.

37
Note: -If you need to continue adding Mesh devices. You need get anther RX4-1500 router to build
MESH network. Press the WPS button on new device and Main router for at least 5 seconds,
and wait for the network to complete.
- Devices that log in through the Mesh network can only access the main route and view
sub-devices in the Application > Mesh
-If failed, please reset both router and follow the setting step again.

Mesh status display

1, After press the WPS button on main router for at least 5 seconds.
Mesh page is displayed as follows: (Not following router connected)

2, After a few seconds, it will enter the following state: Waiting for pairing

3,For Agent Router(Router without network cable connect in)

Unpaired status will shows as below:

38
After successful pairing, you can only log in to the main route and check the status of the
subordinate devices in Agent AP MAC.

39
Chapter 9

Manage the Router

This chapter will show you the configuration for managing and maintaining your router.
It contains the following sections:
- Upgrade the Firmware
- Restore Default Setting
- Change the Login Password
- System Log
- Set up System Time
- Set the Router to Reboot Regularly

40
9. 1. Upgrade the Firmware
VANIN Juplink aims at providing better network experience for users. the latest firmware will
be released at the Juplink official website www.juplink.com, and you can download it for
free
Note: -Do NOT turn off the router during the firmware upgrade.
-Do NOT change firmware file name including firmware extension.

9.1.1. Manual Upgrade

1) Download firmware in your common folder
1) After Log in to Your Router, Click Management > Device Management
2) Click Choose File button, choose firmware in folder. Click Upgrade, your router will reboot.
3) Wait about 2 minutes before reconnect to your router.

9. 2. Restore Default Setting

9.2.1. Manual Restore
Press the reset Button back of the Router for about 10 second, Wait a few minutes for
Router resetting and rebooting.

9.2.1. Web Page Restore

1) After Log in to Your Router, Click Management > Device Management
2) Click Restore Default button in Restore Default Setting Page.
3) Wait a few minutes for the resetting and rebooting.

Note: - During the resetting process, do not turn off the router.
- After reset, you can use the default login password to log in to the web management page.

41
9. 3. Change the Login Password
The account management feature allows you to change your login password of the web
1) After Log in to Your Router, Click Management > User Management
2) Set your password in the New Password and Confirm Password blank.
3) Click Save/Apply Button, Use the new password for future logins

Note: - If you forgot your password and can't log in, you need to restore the router to factory
settings and log in with the default Username and Password.
- The current firmware does not support modifying the username.

9. 4. System Log
When the router does not work normally, you can save the system log and send it to the
technical support for troubleshooting.
Note: - If log mode is turned on, the system will start recording all selected events.
- For the log level, all events equal to or above the selected level will be recorded.
- For the display level, all events equal to or above the selected level will be displayed.

9.4.1. Turned on and set log mode:

1) After Log in to Your Router, Click Management > Logging Management > Log Config
2) Select Enable/Disable and desired values Logging Level, Display Level in drop-down list,
Click Save/Apply button to configure these system log options.
3) Back to Log View page Click View Log then you can view system records.

9.4.2. Save log information to local.

1) After Log in to Your Router, Click Management > Logging Management > Log View
2) Click Save Log, Enter a name in the pop-up dialog box. And click Save files save system
logs to local disk.

42
9. 5. Set up System Time
System time is the time displayed while the router is running. The system time you configure
here will be used for other time-based functions like Parental Controls. You can choose the
way to obtain the system time as needed.
1) After Log in to Your Router, Click Network > Time
2) Select Auto sync with Time Server, in the 1st Time Server field, Select Time Server in the
drop-down server list.
3) Select Time Zone in the drop-down list, Click Save/Apply Button.

43
FAQ
Q1: Why cannot the router setup successfully?
A1: If router did not complete the setup you can try the following:
Press and hold the Reset button on your router with a paperclip or pin until the front illuminated
turns off and the
Green indicators start blinking (about 10 seconds). Install the router again.

Q2: Why cannot the internet appears available?

A2: The Internet appears to be unavailable
If the Internet has difficulty communicating with your router the problem may appear as a
"Cannot find [ internet address ]" message in your Web browser. If you know that the Internet
address is correct and if you've tried several valid Internet addresses with the same result the
message could mean that there's a problem with your ISP or modem communicating with your
router.
Try the following:
- Make sure that the network and power cables are securely connected.
- Make sure that the power outlet that your router is connected to have power.
- Reboot your router.

Q3: Why unable to connect the router signal after a while of successful connection?
A3: Try the following:
-Check on the interface for restrictions and blacklist
-Reboot the router and connect again
-Reset the router and set up again

Q4: How to reset the router if I cannot access the web UI of the router？
A4: When the LED of the router is solid on, press the reset button for 5 seconds and release. After
the LED turns
solid on, the router is restored to factory settings.If useless to press the Reset button, please
confirm long press
the Reset button for at least 5 second with power on.

Q5: Why router and mobile get strong signal but low speed?
A5: Try the following:
- Enter the router’s setting page and verify that your router gets no unknown access device in
- Check the surrounding wireless signals, If there are too many wireless signals, switch channels
and try again.
- Check with your ISP by phone or email to confirm that the service is well.

Q6: Why cannot access the web UI of the router after entering 192.168.0.1?
A6: Try the following solutions and log in again:
- Ensure that your Ethernet cable with internet connectivity is plugged into the WAN port of the

44
router rather than a LAN port.
- Ensure that your wireless device is connected to the router’s SSID.
- Ensure that your wired device is connected to port 1, 2 or 3, 4 of the router properly by
Ethernet cable.
And the device is also set to Obtain an IP address automatically and Obtain DNS server address
automatically.
- Clear the cache of your web browser or replace the web browser, and try logging in again.
- Disable the firewall of your device, and try logging in again.
- If the problem persists, reset your router, follow the setting again.

Q7: How to choose my connection type?

A7: You can choose your internet connection type based on the following table or by consulting
your ISP
You need to double-click and enter a PPPoE user name and password to set up a dial-up
connection.

Q8: An IP address conflict message appears after a computer which is connected to the router.
What should I do?
A8: Try the following:
- Ensure that there is no other DHCP server in your LAN or the other DHCP server is disabled.
- Verify that the IP address of your router is not used by another device in your LAN. The default
IP address
of the router is 192.168.0.1.
- Ensure that the static IP address assigned to the computer in your LAN is not used by other
devices

Q9: I forget the login password of the router. What should I do?
A9: Try to reset the router and log in the router’s setting page.

Q10 : Why cannot my phone find the 5 GHz signal?

A10: Try the following:
- Only devices supporting 5 GHz signal can find and connect to the 5 GHz network.
- Enter the router and Confirm that both signal bands have turned on.

Q11: Why cannot I access the internet after successfully connected to the router’s network?
A11: Try the following:
- Make sure that an Ethernet or Internet cable is securely connected to the blue Internet port on
the back of the router
- Make sure that an Ethernet or Internet cable is securely connected to the appropriate port on
your modem
(This port on the modem is usually labeled Ethernet)

Q12: Why cannot My Windows device detect router wireless networks?

A12: If your Windows device is not detecting your AX router’s wireless network, you might have

45
an older Intel wireless network adapter (some older Intel adapters include: Intel Dual Band
Wireless AC-3160, AC-3165, AC-7260, AC-7265 and AC-8260).
To check which wireless network adapter is on your Windows device:
① Open the Control Panel.
② Enter Device Manager in the search bar at the top of the window.
③ Click Device Manager.
④ Click the arrow next to Network adapters to display the list of adapters.
⑤ Your wireless network adapter displays on the list.
Noted： If your wireless network adapter is not made by Intel and you are still unable to connect
to your router’s SSID, try to reboot or reset your router If your wireless network adapter is an
older Intel model, it might not recognize the wireless signal on your AX router. Connect to your
router directly using a wired connection to access the Internet and download the latest network
adapter drivers. To connect to your router directly and download the latest wireless network
adapter drivers:
① Using an Ethernet cable, connect your Windows device to a LAN port on the back of your AX
router.
② Launch a web browser and visit
https://downloadcenter.intel.com/product/59485/Wireless-Networking.
③ Download the latest wireless network adapter drivers for your adapter model.
④ After you install the latest drivers, your device should recognize your AX router’s wireless
network.

Q13: How to change the DNS servers on your router?

A13:
① Sign into your router's web-based administration: 192.168.0.1
② Tap or click WAN Setting.
③ Select Static in Addressing Type
④ then you can setting DNS manually
⑤ Enter Subnet Mask Information
⑥ Enter Default Gateway
⑦ Enter the primary DNS server you want to use
⑧ Enter the secondary DNS server you'd like to use
⑨ Click Save/Apply

Q14: How to set the Repeater mode on your router?

A14:
① Sign into your router's web-based administration: 192.168.0.1
② Tap or click Application on top menu.
③ Tap or click Repeater
④ Click Scan Wi-Fi
⑤ Select the Wi-Fi you want to Extended
⑥ Enter Your Wi-Fi password
⑦ Click Connect

46
Q15: How to connect to Xfinity cable Modem?
A15:
① Connect to the Wi-Fi of the router and log in to the web management page: 192.168.0.1
② Tap or click Network on top menu.
④ Tap or click WAN Setting
⑤ Select PPPoE in Connection Mode
⑥ Enter the User Name and Password of the Internet Service Provider
⑦ Click Save /Apply

47
FCC statement
FCC compliance information statement
Product Name: VANIN Juplink RX4-1500 Router
Model Number: Juplink RX4-1500
Responsible party:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
Generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device is restricted to be used in the indoor.

Operation is subject to the following two conditions: (1)This device may not cause harmful
interference, and(2)This device must accept any interference received, including
interference that may cause undesired operation.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment and it also complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20 cm between
the radiator & your body.

Caution:
Any changes or modifications not expressly approved by party responsible for compliance
could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

Note:
(1)The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment.
(2)To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45
cable.

48