Starting Formulation

SF 1019
White Tile-like Coating
EPON™ Resin 828 / EPIKURE™ Curing Agent 3192
Formula Material Supplier Pounds Gallons

Part A

EPON Resin 828 Westlake Epoxy 369.0 38.00

Ti-Pure™ R-960 Du Pont Company 100.0 2.86

Magnesium Silicate 100.0 4.26

Diatomaceous Silica 50.0 2.61

Thixatrol ST Thixotrope Elementis Specialties Inc. 20.0 2.36

High Speed Disperse to a min. temperature of 150ºF

and to Grind Hegman 7-, cool and let down with:

Toluene Shell Chemical Co. 119.3 16.58

Total Part A 758.3 66.67

Part B

EPIKURE Curing Agent 3192 Westlake Epoxy 260.0 33.33

Total Part B 260.0 33.33

Total Part A & B 1,018.3 100.00

Mixing Instructions
Pounds Gallons

Part A 758.3 66.67

Part B 260.0 33.33

Part A + B 1,018.3 100.00

Charge ingredients of base component to a suitable container and mix thoroughly. Package
base component and curing agent component separately to be mixed just prior to use.

Formula Notes (A) This system may be readily applied with conventional spray equipment. A Binks Model
62 pressure gun equipped with fluid nozzle 63B, air nozzle 66 PE and needle No. 363A
may be used maintaining a line pressure of 45 psi and a cup pressure of 15 psi. The
same gun equipped with fluid nozzle 68, air nozzle 68B and needle No. 368 may be used
maintaining a line pressure of 35-40 psi and a cup pressure of 7-10 psi.

Generated: May 15, 2024

Issue Date:
Revision:
® and ™ Licensed trademarks of Westlake Inc.
DISCLAIMER

The information provided herein was believed by Westlake. (“Westlake”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Westlake are subject to Westlake’s terms and conditions of sale. WESTLAKE MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY WESTLAKE, except that the product shall conform to Westlake’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 1 of 2
 (B) For the ultimate protection of metal substrates, a corrosion resistant primer should
be used under the high solids coating. This provides insurance that the entire system will
stand up even though the film may be cut through to the metal surface.

Typical Formulation Table 1 / Formulation Properties

Properties

Units Value

Mix ratio Part A : Part B By volume 2:1

By weight 2.92 : 1.0

Total volume solids % 84.0

Pigment volume concentration (PVC) % 14.5

Volatile Organic Compound (VOC) lb/gal 1.19

g/L 143

Potlife hrs 2

Viscosity @ 25°C
Part A + Part B KU 107

Storage Recommendations regarding storage conditions can be obtained by visiting our web site
at www.westlakeepoxy.com

General Information
These are starting formulations and are not proven in the user’s particular application but are simply meant to demonstrate the efficacy of the
products and to assist in the development of the user’s own formulation. It is the user’s responsibility to fully-test and qualify the formulation,
along with the ingredients, methods, applications or equipment identified herein (“Information”), by the user’s knowledgeable formulator or
scientist, and to determine the appropriate use conditions and legal restrictions, prior to use of any Information.

Safety, Storage & Handling

Please refer to the MSDS for the most current Safety and Handling information.

Exposure to these materials should be minimized and avoided, if feasible, through the observance of proper precautions, use of appropriate
engineering controls and proper personal protective clothing and equipment, and adherence to proper handling procedures. None of these
materials should be used, stored, or transported until the handling precautions and recommendations as stated in the Material Safety Data Sheet
(MSDS) for these and all other products being used are understood by all persons who will work with them. Questions and requests for
information on Westlake Epoxy products should be directed to your Westlake Epoxy sales representative, or the nearest Westlake Epoxy sales
office. Information and MSDSs on non-Westlake Epoxy products should be obtained from the respective manufacturer.

Contact Information
For product prices, availability, or order placement, please contact customer service:
www.westlakeepoxy.com/Contacts/

For literature and technical assistance, visit our website at:www.westlakeepoxy.com

Generated: May 15, 2024

Issue Date:
Revision:
® and ™ Licensed trademarks of Westlake Inc.
DISCLAIMER

The information provided herein was believed by Westlake. (“Westlake”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Westlake are subject to Westlake’s terms and conditions of sale. WESTLAKE MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY WESTLAKE, except that the product shall conform to Westlake’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 2 of 2