en
Load charts
Cable excavator
HS8130.1
13163554 327288
projectId: 5777
www.liebherr.com
Product ID
Designation: Cable excavator
Type: 8005.01.03
Document ID
Author: LWN / Technical Documentation Department
Version: 13163554 327288
Issued: 20231016
Boom configuration: Main boom
Manufacturer
Liebherr-Werk Nenzing GmbH
Dr. Hans Liebherr Straße 1
6710 Nenzing
Austria
+43 50809 41-0
info.lwn@liebherr.com
copyright © Liebherr-Werk Nenzing GmbH 2023
2 Load charts 13163554 327288
1 All boom configurations
1.1 Machine configuration
Name Value
Width of base plates 1000 mm (3.28 ft)
Tilting-back supports of main boom Active and buffers
Crawler side frames Short
Undercarriage Standard
Pulling force of winch 350 kN (78,683.50 lbf)
Machine configuration
1.2 Standards
The lifting capacities are calculated on the basis of the following standards:
– EN 474-12
– EN 16228-4
– EN 16228-5
Standards EN 16228-4 and EN 16228-5 are only met if the machine is approved
for the relevant operating mode.
1.3 Radius
The radius is the measured radius between the swing ring center and the hook
copyright © Liebherr-Werk Nenzing GmbH 2023
center or the center of the pulley block. Different reevings result in different
radii with the same boom angle.
13163554 327288 Load charts 3
Main boom
Lifting capacity
Radius
R1 Radius if rope is reeved in once
R2 Radius if rope is reeved in twice
R3 Radius if rope is reeved in 3 to n times
Radius
1.4 Lifting capacity
copyright © Liebherr-Werk Nenzing GmbH 2023
The lifting capacities are only valid on a firm and load-bearing surface.
Lifting capacity values highlighted in gray are limited by the structure of the
machine. Lifting capacity values highlighted in white are limited by the tipping
of the machine.
The lifting capacity is made up of the weights of the following components:
– Hanging rope
– Empty hook
– Lifting device
– Load
4 Load charts 13163554 327288
Main boom
Driving with load according to EN 474-12
1.5 Area of load exposed to the wind
The load area exposed to wind considered in the load calculation including the
cw value is 1.2 m²/t (0.84 inch²/lbs). If the load area exposed to wind including
the cw value is larger than 1.2 m²/t (0.84 inch²/lbs): Reduce the load chart
value. Request reduced load chart values stating the area and the cw value
from the Liebherr customer service.
1.6 Exposure to wind
All stated wind speeds are 3 second wind gust speeds measured at maximum
boom height.
Observe the restrictions related to exposure to wind in the operation manual.
1.7 Reducing the load
Maximum load is reduced depending on the selected maximum wind speed. The
machine operator is responsible for reducing the load and adapting the work
mode.
1.8 Additional weights
Additional weights on the main boom (e.g. walkways, rope guides, jib backstay
straps) increase the load moment and change the load display.
When using steel rope pulleys, calculate the weight difference to plastic rope
pulleys as additional weight.
1.9 Driving with load according to EN 474-12
copyright © Liebherr-Werk Nenzing GmbH 2023
No lifting capacity reduction pursuant to ISO 4305 Tab. 1 is required when
driving with load according to EN 474-12.
The maximum speed allowed is determined by the maximum speed level that
can be selected. The maximum speed allowed applies only on a firm and load-
bearing surface. Reduce dynamic effects. Swinging and active load movement is
not permitted.
13163554 327288 Load charts 5
Main boom
Slope table
1.10 Driving with load with slurry wall hydromill
gripper and slurry wall hydromill cutter
according to EN 16228-5
The maximum speed allowed applies for positioning is 0.1 m/s (0.2 mph) on a
firm and load-bearing surface. Reduce dynamic effects. Swinging and active
load movement is not permitted.
1.11 Single hook operation/two-hook operation
Note the restrictions and instructions in the operation manual regarding single
hook/two-hook operation.
1.12 Slope table
The use on an sloped surface is a special operating mode. Higher dynamic loads
and higher cycle numbers reduce the service life of the machine.
The lifting capacities are a maximum of 75% of the tipping load.
copyright © Liebherr-Werk Nenzing GmbH 2023
6 Load charts 13163554 327288
Main boom
Slope table
Slope
α Longitudinal slope β Cross slope
The lifting capacities are calculated for 1°, 2°, and 3° slopes. Longitudinal
copyright © Liebherr-Werk Nenzing GmbH 2023
slope α and cross slope β are the same size. The practically maximum static
slope of the machine is determined based on the valid load chart.
Turning the top carriage on a sloping ground changes the outreach without
boom adjustment. The maximum possible outreach is definitive for planning and
operation of the lifting capacity.
Only use boom lengths and ballasting as per the load chart.
The lifting capacity calculation accounts for the standstill of the surface only.
The lifting capacity calculation does not account for relative movements
between the load and the location where the load is applied or removed. The
lifting capacities are neither sea-state or offshore lifting capacities.
13163554 327288 Load charts 7
Main boom
Slope table
The lifting capacities apply exclusively to machines that are secured against
sliding on a sloped surface. The sloped surface must be able to transfer the
locally occurring soil pressures. Observe national regulations.
Observe any restrictions and instructions for operation on floating structures in
the operating manual.
copyright © Liebherr-Werk Nenzing GmbH 2023
8 Load charts 13163554 327288
2 Main boom
2.1 Main boom sections
Symbol in opera‐
Main boom component System number System length
tion manual
Main boom base section 2018.33 7 m (23 ft)
Main boom section 3 m (10 ft) 2018.33 3 m (10 ft)
Main boom section 6 m (20 ft) 2018.33 6 m (20 ft)
Main boom head 2018.33 7 m (23 ft)
Main boom components
copyright © Liebherr-Werk Nenzing GmbH 2023
13163554 327288 Load charts 9
Main boom
Boom heads
2.2 Boom heads
Main boom head 2018-1, system number 2018.33
copyright © Liebherr-Werk Nenzing GmbH 2023
10 Load charts 13163554 327288
Special hydraulic
Ident. no.: 13163554/327288/0 Mode: application
Hook insert - two
Swing range: 360° Secondary mode of operation: load-bearing winches
Track width: 2 - Wide track Wind speed [m/s]: 10
Rear counterweight [t]: 29,0 Traveling speed level: 1
Carbody counterweight [t]: 0,0 Main boom length [m]: 29,0
Main boom head: 2018-1 Main boom base section: 2018.33
Reeving: 1 Inclination [°]: 0
Radius [m] Main boom angle [°] Rope pulley height [m] Load [t]
5.9 84.0 30.8 50.0
6.0 83.8 30.7 50.0
7.0 81.8 30.6 46.9
8.0 79.8 30.4 44.1
9.0 77.8 30.2 41.2
10.0 75.8 29.9 37.9
11.0 73.7 29.6 33.7
12.0 71.6 29.2 29.7
13.0 69.5 28.8 26.4
14.0 67.3 28.4 23.7
15.0 65.1 27.9 21.4
16.0 62.9 27.4 19.5
17.0 60.6 26.8 17.7
18.0 58.3 26.2 16.2
19.0 55.9 25.5 14.9
20.0 53.4 24.7 13.8
21.0 50.8 23.9 12.8
22.0 48.1 22.9 11.9
23.0 45.3 21.9 11.1
24.0 42.4 20.8 10.3
25.0 39.2 19.6 9.6
26.0 35.8 18.2 9.0
27.0 32.1 16.6 8.4
28.0 27.9 14.7 7.8
29.0 22.9 12.4 7.2
30.0 16.4 9.3 6.0
30.2 15.0 8.6 5.8
Valid only with preface
13163554 327288 copyright © Liebherr-Werk Nenzing GmbH 11
