ENVITEC

General Specifications
Medical Oxygen Sensors

Measurement Range: Accuracy 0-100% oxygen

< 1 % vol. 02 when calibrated at 100 % 02 Use the advantages:
and Repeatability: Zero Offset:
Linearity Error: Cross < 0,5 % vol. 02 in 100% N2, applied 5 minutes
Interference: < 3 % relative ? Meet EN ISO 21647
< 0.5 % vol. 02 response to: ? Designed and manufactured
10% C02 balance N2 according to EN ISO 9001
80% N20 balance N2 :2000 and
7.5% Halothane balance N2 EN 13485:2003
7.5 % Isoflurane balance N2
7.5 % Enflurane balance N2
9% Sevoflurane balance N2 ? Accurate and reliable
Influence of Humidity: 20% Desflurane balance N2 response
Influence of Pressure: - 0.03 % rel. per % RH at 25°C ? Resistant to N20
proportional to change in oxygen partial ? Excellent signal stability
Influence of Mechanical Shock: pressure
? High product guality
Operating Temperature: < 1% relative after a fall from 1 m
Temperature Compensation: 0 to 50°C
Effect of Temperature built-in NTC compensation (see below) ? Short lead times
Compensation (steady state): between +5 °C and +25 °C: 3 % relative error ? Technical support
Operating Humidity: Long Term between 0 °C and +50 °C: 5 % relative error
Output Drift: 0-99 % RH non-condensing
< 1 % vol oxygen per month
Storage Temperature: typically < -15 % relative over lifetime
Recommended Storage: -20 to +50 °C
Recommended Load: +5to+15°C >
Warm-UpTime: Weight: lOkOhms
< 30 minutes, after replacement of sensor
Warranty Period: approximately 28 grams
approximately 43 grams OOM107 series
15 months

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air

Oxygen Sensor Output Signal in Air Response Nominal Sensor Lifetime Electrical Interface
Time [90%]
OOM101 46uA to 63uA
no temperature compensation
<12 seconds 500.000 % volume oxygen hours Gold plated slip rings

OOM102 9mVto 14mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours 3pin molex®

OOM102-1 9mVto 14mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours 3,5mm Mono Jack

OOM103 9mVto 13mV

temperature compensation
< 5 seconds 500.000 % volume oxygen hours 3pin molex®

OOM103-1 9mVto 13mV

temperature compensation
< 5 seconds 500.000 % volume oxygen hours 3,5mm Mono Jack

OOM103-1M 9mVto 13mV

temperature compensation
< 5 seconds 500.000 % volume oxygen hours Switchcraft® Mini Power Jack

OOM104 24uAto32uA
no temperature compensation
<12 seconds 750.000 % volume oxygen hours Gold plated slip rings

OOM105 Teledyne® TED range < 5 seconds 500.000 % volume oxygen hours molex® plug 4P4C

OOM106 9mVto 13mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours 3pin molex®

OOM107 170nAto230nA
no temperature compensation
<12 seconds 250.000 % volume oxygen hours Gold plated slip rings

OOM107-2 170nAto230nA
no temperature compensation
<12 seconds 250.000 % volume oxygen hours Gold plated slip rings

OOM110 9mVto 13mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours Modular Jack 6P4C

OOM111 9mVto 13mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours 3,5mm Stereo Jack

OOM201 24uA to 32uA (Dual Cathode)

no temperature compensation
<12 seconds 500.000 % volume oxygen hours Gold plated slip rings

OOM202 13mVto 16mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours 3pin molex®

OOM202-1 13mVto 16mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours 3,5mm Mono Jack

OOM202-2 9mVto 13mV

temperature compensation
<12 seconds 1.000.000 % volume oxygen hours flying leads with 3pin female
molex® connector
OOM202-2S 9mVto11,5mV
temperature compensation
<12 seconds 1.000.000 % volume oxygen hours AMP MATE-N-LOK / 2 circuit

OOM204 9mV to 13,5mV (Dual Cathode)

temperature compensation
<12 seconds 500.000 % volume oxygen hours 3pin molex®
 Product Specification
Oxygen Sensor 00Ml01
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical Interface: 14 to 20 mV, load 300 Ohms
Accuracy and Repeatability: Gold plated slip rings Use the advantages:
< 1 % vol. 02 when calibrated at 100 %
Linearity error: Oxygen < Meets EN ISO 21647
Response time: Zero < 3 % relative < Designed and manufactured
Offset Voltage: < 12sec. to 90% of final value according to EN ISO 9001
< 200 MV in 100% nitrogen :2000 and EN ISO 13485:
Cross Interference: Influence applied after 5 min 2003
of Humidity: Influence of Meets EN ISO 21647 requirements -
Pressure: 0.03%rel.per%RHat25°C proportional
< Accurate and reliable
to change in oxygen partial pressure
response
Influence of Mechanical Shock: < 1% relative after a fall from 1 m
Operating Temperature: < Resistant to N20
0 to +50°C
Temperature Compensation: No temperature compensation < Excellent signal stability
Operating Humidity: Long Term 0-99 % RH non-condensing < High product guaIity
Output Drift: < 1 % vol. oxygen per month
typically < -15 % relative over lifetime < Short lead times
Storage Temperature: -20 to +50 °C < Technical support
Recommended Storage: +5to+15°C
Recommended Load: Warm- > lOkOhms
Up Time: Nominal Sensor < 30 minutes, after replacement of sensor
Lifetime: Weight: Part No.: > 500.000 % vol. oxygen hours
approximately 28 grams
01-00-0013

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air

Dimension in mm
 Product Specification
Oxygen Sensor 00Ml02 / 00Ml 02-1
ENVITEC
by Honeywell

Measurement Range: 0-100% oxygen

Output in ambient air: 9 to 14mV
Electrical Interface: OOM102: 3pin (Molex 22-11-1031) Use the advantages:
00M102-1:3,5mm Mono Jack
Accuracy and Repeatability: < 1 % vol. 02 when calibrated at 100 % I Meets EN ISO 21647
Oxygen I Designed and manufactured
Linearity error: < 3 % relative according to EN ISO 9001
Response time: Zero < 12sec. to 90% of final value :2000 and EN ISO 13485:
Offset Voltage: < 200 MV in 100% nitrogen 2003
applied after 5 min
Cross Interference: Meets EN ISO 21647 requirements -
I Accurate and reliable
Influence of Humidity: 0.03%rel.per%RHat25°C proportional to
response
Influence of Pressure: change in oxygen partial pressure
I Resistant to N20
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: 0 to 50°C I Excellent signal stability
Operating Temperature: built-in NTC compensation between +25°C I High product guaIity
Temperature Compensation: and +40°C: 3 % relative error between 0 °C
Effect of Temperature and +50 °C: 8 % relative error 0-99 % RH I Short lead times
Compensation (steady state): non-condensing I Technical support
Operating Humidity: Long Term < 1 % vol. oxygen per month
Output Drift: typically < -15 % relative over lifetime
-20 to +50 °C
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 1.000.000 % vol. oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0019/OOM102
01-00-0020/OOM102-1

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air

Dimension in mm
 ENVITEC
Product Specification
Oxygen Sensor OOM103/OOM103-1

Measurement Range: 0-100% oxygen

Output in ambient air: 9 to 13mV
Electrical Interface: OOM103: 3pin (Molex 22-11-1031) Use the advantages:
OOM103-1: 3,5mm Mono Jack
Accuracy and Repeatability: < 1 % vol. 02 when calibrated at 100 % I Meet EN ISO 21647
Oxygen I Designed and
Linearity error: < 3 % relative manufactured according
Response time: Zero < 5sec. to 90 % of final value to EN ISO 9001 and EN
Offset Voltage: < 100 yV in 100 % nitrogen
ISO 13485
applied for 5 min
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03 % rel. per % RH at 25-C I Accurate and reliable fast
Influence of Pressure: proportional to change in oxygen partial response
pressure I Resistant to N20
Influence of Mechanical < 1% relative after a fall from 1m I Excellent signal stability
Shock: I High product quality
Operating Temperature: 0 to 50-0
Temperature Compensation: built-in NTC compensation
Effect of Temperature I Short lead times
between +25 "C and +40 <C: 3 %
Compensation (steady state): relative error I Technical support
between 0 "C and +50 "0:8% relative
error
Operating Humidity: 0-99% RH non-condensing
Long Term Output Drift: < 1 % vol. oxygen per month
typically < -15 % relative over lifetime
Storage Temperature: -20 to +50 "C
Recommended Storage: +5 to +15 <C
Recommended Load: >10 kOhms
Warm-Up Time: < 30 minutes, after replacement of
sensor
Nominal Sensor Lifetime: > 500.000 % vol. oxygen hours
Weight: approximately 28 grams 01-00-
Part No.: 0015/OOM103 01-00-
0016/OOM103-1
Product Specification
Oxygen Sensor OOM103-1M
ENVITEC
by Honeywell

Measurement Range: 0-100% oxygen

Output in ambient air: 10 to 13mV
Electrical Interface: Switchcraft® Mini Power Jack
Accuracy and Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen
Linearity error: < 3 % relative
Response time: Zero < 5sec. to 90 % of final value
Offset Voltage: < 100/vV in 100 % nitrogen applied for 5
min
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03 % rel. per % RH at 25<C
Influence of Pressure: proportional to change in oxygen partial
pressure
Influence of Mechanical < 1% relative after a fall from 1m
Shock:
Operating Temperature: 0 to 50<C
Temperature Compensation: built-in NTC compensation
Effect of Temperature between +25 "C and +40 "0:3% relative
Compensation (steady error
state): between 0 O and +50 "0:8% relative
error
Operating Humidity: Long 0-99 % RH non-condensing
Term Output Drift: < 1 % vol. oxygen per month
typically < -15 % relative over lifetime
Storage Temperature: -20 to +50 <C
Recommended Storage: +510+15-0
Recommended Load: Warm- >10 kOhms
Up Time: < 30 minutes, after replacement of
sensor
Nominal Sensor Lifetime: > 500.000 % vol. oxygen hours
Weight: approximately 28 grams 01-00-
Part No.: 0090
Product Specification
Oxygen Sensor 00Ml04
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical 14 to 20 mV, load 600 Ohms
Interface: Accuracy and Gold plated slip rings Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 12sec. to 90% of final value according to EN ISO 9001
Offset Voltage: < 200 MV in 100% nitrogen :2000 and EN ISO 13485:
applied for 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03%rel.per%RHat25°C proportional I Accurate and reliable
Influence of Pressure: to change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: I Resistant to N20
0 to 50°C
Operating Temperature: No temperature compensation I Excellent signal stability
Temperature Compensation: 0-99 % RH non-condensing I High product guaIity
Operating Humidity: Long Term < 1 % vol. oxygen per month
Output Drift: typically < -15 % relative over lifetime I Short lead times
-20 to +50 °C I Technical support
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 750.000 % vol. oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0049
 Product Specification
Oxygen Sensor OOM105
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical Compatible with Teledyne® T-7 sensor
Interface: Accuracy and Molexplug4P4C Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 5sec. to 90 % of final value according to EN ISO 9001
Offset Voltage: < 100uVin 100% nitrogen :2000 and EN ISO 13485:
applied after 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements - 0.03
Influence of Humidity: % rel. per % RH at 25°C proportional to I Accurate and reliable fast
Influence of Pressure: change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: I Resistant to N20
0 to 50°C
Operating Temperature: I Excellent signal stability
built-in NTC compensation between +25 °C
Temperature Compensation: and +40 °C: 3 % relative error between 0 °C I High product guaIity
Effect of Temperature and +50 °C: 8 % relative error 0-99 % RH
Compensation (steady state): non-condensing I Short lead times
Operating Humidity: Long Term < 1 % vol oxygen per month I Technical support
Output Drift: typically < -15 % relative over lifetime
-20 to +50 °C
Storage Temperature: +5to+15°C
Recommended Storage: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 500.000 % vol oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0053

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
 Product Specification
Oxygen Sensor OOM106
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical 9 to 13mV
Interface: Accuracy and 3pin (Molex 22-11-1031) Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 12sec. to 90 % of final value according to EN ISO 9001
Offset Voltage: <200uVin 100% nitrogen :2000 and EN ISO 13485:
applied for 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements - 0.03
Influence of Humidity: % rel. per % RH at 25°C proportional to
I Accurate and reliable
Influence of Pressure: change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: I Resistant to N20
0 to 50°C
Operating Temperature: built-in NTC compensation between +25 °C I Excellent signal stability
Temperature Compensation: and +40 °C: 3 % relative error between 0 °C I High product guaIity
Effect of Temperature and +50 °C: 8 % relative error 0-99 % RH
Compensation (steady state): non-condensing I Short lead times
Operating Humidity: Long Term < 1 % vol. oxygen per month I Technical support
Output Drift: typically < -15 % relative over lifetime
-20 to +50 °C
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 1.000.000 % vol. oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0091

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
 Product Specification
Oxygen Sensor 00Ml07 / 00Ml 07-2
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical 170to230MA
Interface: Accuracy and Gold plated slip rings Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 12sec. to 90% of final value according to EN ISO 9001
Offset Voltage: < 200 MV in 100% nitrogen :2000 and EN ISO 13485:
applied for 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03%rel.per%RHat25°C proportional
I Accurate and reliable
Influence of Pressure: to change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: I Resistant to N20
0 to 50°C
Operating Temperature: No temperature compensation I Excellent signal stability
Temperature Compensation: 0-99 % RH non-condensing I High product guaIity
Operating Humidity: Long Term < 1 % vol. oxygen per month
Output Drift: typically < -15 % relative over lifetime I Short lead times
-20 to +50 °C I Technical support
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 250.000 % vol. oxygen hours
Sensor Lifetime: Weight: approximately 43 grams
Part No.: 01-00-0058/OOM107 01-
00-0080/OOM107-2
 Product Specification
Oxygen Sensor 00Ml09 / 00Ml 09-LF2
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

Fast Response Oxygen Sensor
ambient air: Electrical 9 to 13mV
Interface: Accuracy and 3pin (Molex 22-11-1031) for Medical Breath by Breath
Repeatability: < 1 % vol. 02 when calibrated at 100 % Analysis
Oxygen
Linearity error: < 3 % relative Use the advantages:
Response time: Zero < 300msec. to 90 % of final value
Offset Voltage: < 50 uV in 100 % nitrogen I Meets EN ISO 21647
applied for 5 min I Designed and manufactured
Cross Interference: Meets EN ISO 21647 requirements - according to EN ISO 9001
Influence of Humidity: 0.03%rel.per%RHat25°C proportional to
:2000 and EN ISO 13485:
Influence of Pressure: change in oxygen partial pressure
2003
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: 0 to 50°C
Operating Temperature: built-in NTC compensation I Accurate and reliable ultra
Temperature Compensation: between +25 °C and +40 °C: 3 % relative fast response
Effect of Temperature error I Resistant to N20
Compensation (steady state): between 0 °C and +50 °C: 8 % relative error I Excellent signal stability
0-99 % RH non-condensing I High product guaIity
Operating Humidity: Long < 1 % vol. oxygen per month I OOM109: designed for main
Term Output Drift: typically < -15 % relative over lifetime
stream application
-20 to +50 °C
Storage Temperature: I OOM109-LF2: designed for
+5to+15°C
Recommended Storage: side stream application
> lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 200 000 % vol. oxygen hours I Short lead times
Sensor Lifetime: Weight: approximately 28 grams I Technical support
Part No.: 01-00-0085/OOM109
01-00-0116/OOM109-LF2

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
 Product Specification
Oxygen Sensor OOM110
ENVITEC
by Honeywell

Measurement Range: Output 0-100% oxygen 10

in ambient air: Electrical to 12mV Modular
Interface: Accuracy and Jack 6P4C Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and
Response time: Zero < 12sec. to 90 % of final value manufactured according
Offset Voltage: < 200 £7V in 100 % nitrogen to EN ISO 9001 and EN
applied after 5 min
ISO 13485
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03 % rel. per % RH at 25-C
Influence of Pressure: proportional to change in oxygen partial I Accurate and reliable
pressure response
Influence of Mechanical < 1% relative after a fall from 1m I Resistant to N20
Shock: I Excellent signal stability
Operating Temperature: 0 to 50-0 I High product quality
Temperature Compensation: built-in NTC compensation
Effect of Temperature between +25 "C and +40 <C: 3 %
Compensation (steady state): I Short lead times
relative error
between 0 "C and +50 "0:8% relative I Technical support
error
Operating Humidity: 0-99% RH non-condensing
Long Term Output Drift: < 1 % vol oxygen per month
typically < -15 % relative over lifetime
Storage Temperature: -20 to +50 "C
Recommended Storage: +5 to +15 <C
Recommended Load: >10 kOhms
Warm-Up Time: < 30 minutes, after replacement of
sensor
Nominal Sensor Lifetime: > 1.000.000 % vol oxygen hours
Weight: approximately 50 grams 01-00-
Part No.: 0098

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
 Product Specification
Oxygen Sensor 00Ml 11
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical 11 to13mV
Interface: Accuracy and Stereo phone jack (3,5mm) Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 12sec. to 90% of final value according to EN ISO 9001
Offset Voltage: < 200 MV in 100% nitrogen :2000 and EN ISO 13485:
applied after 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03%rel.per%RHat25°C proportional to
Sensor coding integrated
Influence of Pressure: change in oxygen partial pressure
Accurate and reliable
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: response Resistant to N20
0 to 50°C
Operating Temperature: built-in NTC compensation between +25°C Excellent signal stability High
Temperature Compensation: and +40°C: 3 % relative error between 0 °C product guaIity
Effect of Temperature and +50 °C: 8 % relative error 0-99 % RH
Compensation (steady state): non-condensing Short lead times
Operating Humidity: Long Term < 1 % vol oxygen per month Technical support
Output Drift: typically < -15 % relative over lifetime
-20 to +50 °C
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 1.000.000 % vol oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Sensor coding: Part No.: Built-in data memory chip
01-00-0114

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
 Product Specification
Oxygen Sensor OOM112
ENVITEC
by Honeywell

Measurement Range: 0-100% oxygen

Output in ambient air: 25 to 38 mV
Electrical Interface: Gold plated slip rings Use the advantages:
Accuracy and Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative @ 70 % oxygen applied I Designed and
for 5 minutes manufactured according
Response time: Zero < 12sec. to 90 % of final value to EN ISO 9001 and EN
Offset Voltage: < 200 £7V in 100 % nitrogen ISO 13485
applied after 5 min
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03 % rel. per % RH at 25-C I Accurate and reliable
Influence of Pressure: proportional to change in oxygen partial response
pressure I Resistant to N20
Influence of Mechanical < 1% relative after a fall from 1m I Excellent signal stability
Shock: I High product quality
Operating Temperature: 0 to +50<C
Temperature Compensation: Temperature compensation built-in
Operating Humidity: I Short lead times
0-99 % RH non-condensing
Long Term Output Drift: < 1 % vol. oxygen per month I Technical support
typically < -15 % relative over lifetime
Storage Temperature: -20 to +50 "C
Recommended Storage: +5 to +15 <C
Recommended Load: Warm- >10 kOhms
Up Time: < 30 minutes, after replacement of
sensor
Nominal Sensor Lifetime: > 500.000 % vol. oxygen hours
Weight: approximately 28 grams 1001202
Part No.:

All specifications are applicable at standard conditions: 1013 hPa, 25'C dry
ambient air
Product Specification
Oxygen Sensor OOM201
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical 14 to 20 mV (Dual Cathode), load 600 Ohms
Interface: Accuracy and Gold plated slip rings Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 12sec. to 90% of final value according to EN ISO 9001
Offset Voltage: < 200 MV in 100% nitrogen :2000 and EN ISO 13485:
applied after 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03%rel.per%RHat25°C proportional to
I Accurate and reliable
Influence of Pressure: change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: I Resistant to N20
0 to 50°C
Operating Temperature: No temperature compensation 0- I Excellent signal stability
Temperature Compensation: 99 % RH non-condensing I High product guaIity
Operating Humidity: Long Term < 1 % vol. oxygen per month
Output Drift: typically < -15 % relative over lifetime I Short lead times
-20 to +50 °C I Technical support
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 500.000 % vol. oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0014
Product Specification
Oxygen Sensor OOM202
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Electrical !3to16mV
Interface: Accuracy and 3pin (Molex 22-11-1031) Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: < 2 % relative I Designed and manufactured
Response time: Zero < 12 sec. to 90% of final value according to EN ISO 9001
Offset Voltage: < 150 MV in 100% nitrogen :2000 and EN ISO 13485:
applied for 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements -
Influence of Humidity: 0.03%rel.per%RHat25°C proportional to
I Accurate and reliable
Influence of Pressure: change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: I Resistant to N20
0 to 50°C
Operating Temperature: built-in NTC compensation between +25°C I Excellent signal stability
Temperature Compensation: and +40°C: 3 % relative error between 0 °C I High product guaIity
Effect of Temperature and +50 °C: 8 % relative error 0-99 % RH
Compensation (steady state): non-condensing I Short lead times
Operating Humidity: Long Term < 1 % vol oxygen per month I Technical support
Output Drift: typically < -15 % relative over lifetime
-20 to +50 °C
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 1.000 000 % vol oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0047
 Product Specification
Oxygen Sensor OOM202-1
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen 13

ambient air: Electrical to 16mV 3,5mm
Interface: Accuracy and Mono Jack Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets DIN EN 21647
Linearity error: < 3 % relative I Designed and manufactured
Response time: Zero < 12 sec. to 90% of final value according to EN ISO 9001
Offset Voltage: <200uVin 100% nitrogen :2000 and EN ISO 13485:
applied for 5 min 2003
Cross Interference: Meets EN ISO 21647 requirements - 0.03
Influence of Humidity: % rel. per % RH at 25°C proportional to
I Accurate and reliable
Influence of Pressure: change in oxygen partial pressure
response
< 1% relative after a fall from 1 m
Influence of Mechanical Shock: 0 to 50°C I Resistant to N20
Operating Temperature: built-in NTC compensation between +25 °C I Excellent signal stability
Temperature Compensation: and +40 °C: 3 % relative error between 0 °C I High product guaIity
Effect of Temperature and +50 °C: 8 % relative error 0-99% RH non-
Compensation (steady state): condensing I Short lead times
Operating Humidity: Long Term < 1 % vol. oxygen per month I Technical support
Output Drift: typically < -15 % relative over lifetime
-20 to +50 °C
Storage Temperature: +5to+15°C
Recommended Storage: > lOkOhms
Recommended Load: < 30 minutes, after replacement of sensor
Warm-Up Time: Nominal > 1.000 000 % vol. oxygen hours
Sensor Lifetime: Weight: approximately 28 grams
Part No.: 01-00-0021

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
Product Specification
Oxygen Sensor OOM202-2
ENVITEC
by Honeywell

Measurement Range: 0-100% oxygen

Output in ambient air: 9 to 13mV
Electrical Interface: Use the advantages:
Flying leads with 3pin female connector
(Molex 22-01-2037)
Accuracy and Repeatability: < 1 % vol. 02 when calibrated at 100 % I Meet DIN EN 21647
Oxygen I Designed and
Linearity error: < 3 % relative manufactured according
Response time: Zero < 12 sec. to 90 % of final value to EN ISO 9001 and EN
Offset Voltage: < 200 £7V in 100 % nitrogen ISO 13485
applied for 5 min
Cross Interference: Meets EN ISO 21647 requirements - 0.03%
Influence of Humidity: I Accurate and reliable
rel. per % RH at 250 proportional to change in
Influence of Pressure: response
oxygen partial pressure
< I aResistant
1% relative after to N20
fall from 1m
Influence of Mechanical Shock: 0 to 50<C I Excellent signal stability
Operating Temperature: built-in NTC compensation between +25 "C to I High product quality
Temperature Compensation: +40 "0:3% relative error between 0 O to +50
Effect of Temperature "0:8% relative error 0-99% RH non-
Compensation (steady state): condensing I Short lead times
Operating Humidity: Long I Technical support
< 1%
Term Output Drift: vol oxygen per month
typically < -15 % relative over lifetime
Storage Temperature: -20 to +50 <C
Recommended Storage: +510+15-0 >10
Recommended Load: kOhms
Warm-Up Time: Nominal < 30
Sensor Lifetime: Weight: minutes, after replacement of sensor
Part No.: > 1,000,000% vol oxygen hours
approximately 28 grams
01-00-0068
<
All specifications are applicable at standard conditions: 1013 hPa, 25 C dry ambient air
 Product Specification
Oxygen Sensor OOM202-2S
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen 9

ambient air: Electrical to 11,5mV
Interface: Accuracy and AMP350777-1 Use the advantages:
Repeatability: < 1 % vol. 02 when calibrated at 100 %
Oxygen I Meets EN ISO 21647
Linearity error: Response < 3 % relative I Designed and manufactured
time: Zero Offset Voltage: < 12 sec. to 90% of final value according to EN ISO 9001
Cross Interference: < 200 uV in 100 % nitrogen applied for 5 min :2000 and EN ISO 13485:
Influence of Humidity: Meets EN ISO 21647 requirements 2003
Influence of Pressure: - 0.03% rel. per%RHat25°C proportional to
change in oxygen partial pressure I Accurate and reliable
Influence of Mechanical Shock: < 1% relative after a fall from 1 m
response
Operating Temperature: 0 to 50°C
I Resistant to N20
Temperature Compensation: built-in NTC compensation between +25 °C
Effect of Temperature I Excellent signal stability
and +40°C: 3 % relative error between 0 °C
Compensation (steady state): and +50 °C: 8 % relative error 0-99% RH I High product guaIity
Operating Humidity: Long Term non-condensing
Output Drift: < 1 % vol oxygen per month I Short lead times
typically < -15 % relative over lifetime I Technical support
Storage Temperature: -20 to +50 °C
Recommended Storage: +5to+15°C
Recommended Load: > lOkOhms
Warm-Up Time: Nominal < 30 minutes, after replacement of sensor
Sensor Lifetime: Weight: > 1.000 000 % vol oxygen hours
Part No.: approximately 30grams
1000106

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air
 Product Specification
Oxygen Sensor OOM204
ENVITEC
by Honeywell

Measurement Range: Output in 0-100% oxygen

ambient air: Output difference: 9 to 13,5mV(each of two channels)
Electrical Interface: Accuracy 1,25mV (between the two channels) 3pin Use the advantages:
and Repeatability: (Molex 22-11-1031)
< 1 % vol. 02 when calibrated at 100 % I Meets EN ISO 21647
Linearity error: Oxygen I Designed and manufactured
Response time: Zero < 3 % relative according to EN ISO 9001
Offset Voltage: < 12sec. to 90 % of final value :2000 and EN ISO 13485:
<200uVin 100% nitrogen 2003
Cross Interference: applied after 5 min
Influence of Humidity: Meets EN ISO 21647 requirements -
I Accurate and reliable
Influence of Pressure: 0.03% rel. per%RHat25°C proportional
response
to change in oxygen partial pressure
Influence of Mechanical Shock: I Resistant to N20
< 1% relative after a fall from 1 m
Operating Temperature: 0 to 50°C I Excellent signal stability
Temperature Compensation: built-in NTC compensation between +25 °C I High product guaIity
Effect of Temperature and +40 °C: 3 % relative error between 0 °C
Compensation (steady state): and +50 °C: 8 % relative error 0-99% RH non- I Short lead times
Operating Humidity: Long Term condensing I Technical support
Output Drift: < 1% vol. oxygen per month
typically < -15 % relative over lifetime
Storage Temperature: -20 to +50 °C
Recommended Storage: +5to+15°C
Recommended Load: > lOkOhms
Warm-Up Time: Nominal < 30 minutes, after replacement of sensor
Sensor Lifetime: Weight: > 500.000 % vol. oxygen hours
Part No.: approximately 28 grams
01-00-0097

All specifications are applicable at standard conditions: 1013 hPa, 25°C dry ambient air