1. Verify whether the starter is required or not for a fluorescent lamp after the ignition.
Mark distribution
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
2. With the help of a two-way Switch, Control the given lamp load.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
3. Assemble the below circuit in the given board and verify the connectivity of the circuit
using multimeter and disassemble the components from the board.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
4. Make a Stair case wiring by using two way Controlled switch.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
5. Construct a wiring in such a way so that a single lamp can be controlled from two
different places and how many way switch you need for that connection.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
6. Conduct an experiment using a starter to show the lamp will continue to glow even when
starter is removed.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
7. Measure the energy drawn by the given single phase load by using suitable measuring
equipment.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
8. Design a circuit to control a lamp in a bed room using two switches. One of the switches
is at the entrance of the room and other switch is near the bed. Draw the truth table.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
9. Measure the energy drawn by the given single phase load by using suitable measuring
equipment.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
10. Design a suitable circuit with two switches to control a lamp and to verify the following
table
SWITCH SWITCH LAMP
1 2
ON ON OFF
ON OFF ON
OFF ON ON
OFF OFF OFF
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
11. Assemble the below circuit in the given board and verify the connectivity of the circuit
using multimeter and disassemble the components from the board.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
12. To assemble and solder the electronic components in the circuit using PCB.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
13. To assemble and solder the electronic components in the circuit using PCB.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
14. Assemble the below circuit in the given board and verify the connectivity of the circuit
using multimeter and disassemble the components from the board.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
15. To assemble and solder the electronic components in the circuit using PCB.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
16. Assemble the below circuit in the given board and verify the connectivity of the circuit
using multimeter and disassemble the components from the board.
Aim&Procedure Model Finish& Viva Result Total
(10) (20) accuracy(10) voice(5) (5) (50)
