3M™ Reusable Half Mask
7500 Series
Technical datasheet
Description
3M™ Reusable Half Mask 7500 Series have set a new standard
in comfort. This facepiece was designed with the wearer in
mind. Its soft sealing surface, along with the 3M™ Cool Flow™
Valve, enhances wearer comfort and face fit. Reduced breathing
resistance helps to minimise heat build-up in the mask and
increases your comfort.
Available in three sizes, all masks have the 3M™ bayonet
connection system allowing connection to a broad range of twin
lightweight filters or approved powered and supplied air systems
to protect against gases, vapours and particulates depending on
your individual needs.
Key Features
• Dual-mode head harness adjusts easily for standard
or drop-down mode
Standards and approvals
These products have been tested to the relevant European
Standards: 3M™ Reusable Half Mask, 7500 Series to EN
140:1998 for Half Masks, EN 12942:1998 + A2:2008 and EN
14594:2005 (with approved air delivery units). These products
are in conformity with European regulation and UK regulations
and/or Directives. The Certificates and Declarations of
Conformity available at the following website: www.3M.com\
Respiratory\certs
Use
When properly fitted and operated, 3M™ Reusable Half Mask
7500 Series may be used:
3M™ Reusable Half Mask Nominal Protection
7500 Series Factor*
P1 Particulate Filter 4
P2 Particulate Filter 12
P3 Particulate Filter 48
50 or 1000ppm (Whichever is
Class 1 Gas & Vapour Filters
lower)
Class 2 Gas & Vapour Filters 50 or 5000ppm (Whichever
is lower)
3M™ Versaflo™ TR-600 & TR- See Powered Air Respirator
800 Powered Air Respirator Datasheet
S-200+ Supplied Air Unit See S-200+ Datasheet
3M™ Reusable Half Masks 7500 Series
Gas and Vapour/Combination Filters
Filter Standard Class Hazard
6051 (06911) A1
EN 14387: 2004
Organic Vapours bp>65 °C
+A1:2008
6055 (06915) A2
EN 14387: 2004
6054 K1 Ammonia and derivatives
+A1:2009
EN 14387: 2004 Organic vapours (boiling point above 65°C),
6057 ABE1
+A1:2010 inorganic vapours and acid gases.
Organic vapours (boiling point above 65°C),
EN 14387: 2004
6059 ABEK1 inorganic vapours, acid gases, ammonia and
+A1:2011
its derivatives.
EN 14387: 2004
6075 A1 + formaldehyde Formaldehyde, Organic Vapours bp>65 °C
+A1:2012
EN 14387: 2004 Organic gases and vapours (boiling point
6091 A1P3 R
+A1:2013 above 65°C) and particulates
Organic vapours (boiling point above 65°C)
EN 14387: 2004 ABEK1P3 R + inorganic vapours, acid gases, ammonia and
6092
+A1:2014 formaldehyde its derivatives, formaldehyde up to 10 ppm
and particulates
EN 14387: 2004 Organic gases and vapours (boiling point
6095 A2P3 R
+A1:2015 above 65°C) and particulates
EN 14387: 2004 Organic vapours (boiling point above 65°C),
6096 A1E1HgP3 R
+A1:2016 acid gases, mercury and particulates
3M™ Reusable Half Masks 7500 Series
Particulate Filters
Filter Standard Class Hazard
5911 P1 R
EN 143:2000 /
5925(06925) P2 R Solid and liquid particles
A1:2006
5935 P3 R
2125 EN 143:2000 / P2 R
Solid and liquid particles
2135 A1:2006 P3 R
Solid and liquid particles, plus relief from Ozone up
2128 EN 143:2000 / P2 R
to 10 x OEL), plus relief from nuisance level acid gas/
2138 A1:2006 P3 R
organic vapour
EN 143:2000 / Solid and liquid particles – in solid plastic case for
6035 P3 R
A1:2006 rough application
Solid and liquid particles – in solid plastic case for
EN 143:2000 / rough application, Hydrogen Fluoride up to 30 ppm
6038 P3 R
A1:2006 and relief from nuisance level, Organic Vapour and
acid gases below OEL.
Breathing Tube Options
Breathing Tube 3M™ Versaflo™ Powered Air Turbo 3M™ Air Supply Unit S-200+
TR-602E / TR-802E
BT-63 / BT-64 Yes N/A
S-222 N/A Yes
Use limitations Cleaning and storage
Before use, check the expiration date. For other use 1. Disassemble by removing the filters/breathing tube (if
limitations please refer to the User Information supplied with applicable), head straps and other parts.
the products. These respirators do not supply oxygen. Do not
use in oxygen deficient areas.* 2. Clean and sanitise the mask (excluding filters) using
3M™ 105 Face Seal Cleaner or immersing in warm
Do not use for respiratory protection against atmospheric cleaning solution and scrubbing with a soft brush until
contaminants that have poor warning properties or are clean. Parts may also be cleaned in a domestic washer.
unknown or immediately dangerous to life and health (IDLH) If necessary,wash the outside of the breathing hose
or against contaminants, which generate high heats of carefully using warm water solution containing a mild
reaction with chemical filters. (The 3M™ S-200+ Supplied- detergent. Ensure the breathing hose connections are free
Air Respirator System can be used against contaminants with from all dirt or debris that could prevent an effective seal
poor warning properties, subject to other use limitations). Do with the powered air turbo.
not misuse, alter, modify or repair this product.
3. Disinfect respirator by soaking in a solution of quaternary
Do not use with beards or other facial hair that prevent ammonium disinfectant or sodium hypochlorite (30ml
direct contact between the face and the edge of the household bleach in 7.5l of water) or other disinfectant.
respirator.
4. Rinse in fresh, warm water and air-dry in non-
Do not use with unknown concentrations of contaminants. contaminated atmospheres. Water temperature should
not exceed 50°C.
Leave the work area immediately and check the integrity of
the respirator and replace face mask if: Do not use cleaning agents that contain lanolin or other oils.
• Damage has occurred or is apparent. Do not autoclave.
• Breathing becomes difficult or increased breathing
resistance occurs.
• Dizziness or other distress occurs.
• You taste or smell the contaminant or an irritation occurs.
* 3M definition minimum 19.5% by volume oxygen
3M™ Reusable Half Mask 7500 Series
Sizes and weight Spare parts and Component
accessories
Small (7501)
7580 Replacement strap
Medium (7502)
Large (7503) 7581 Head harness assembly
Approximate weight: 135 grams 7582 Inhalation valve
Shelf life: 5 years from production date when stored 6583 Exhalation valve
at the storage conditions stated on the packaging.
*The shelf life as defined above remains an indicative and maximum data, 7585F Fabric head cradle
subject to many external and non-controllable factors. It may never be
interpreted as a warranty.
7586 Filter holder (includes valve)
Component Material 501 Retainer for 5000 Series filters
Face seal Silicone rubber
603 Particulate filter platform
Filter holder Polybutylene terephthalate
105 Face seal wipe
Exhalation valve cover Polybutylene terephthalate
S-200+ Supplied air respirator
Inhalation valve Silicone rubber
Exhalation valve Silicone rubber
Straps Polyester/polyurethane
Head cradle Polyethylene
IMPORTANT NOTICE
The use of the 3M product described within this document assumes that the user has previous experience of this type of product and that it will be used by a
competent professional. Before any use of this product it is recommended to complete some trials to validate the performance of the product within its expected
application. All information and specification details contained within this document are inherent to this specific 3M product and would not be applied to other
products or environment. Any action or usage of this product made in violation of this document is at the risk of the user. Compliance to the information and
specification relative to the 3M product contained within this document does not exempt the user from compliance with additional guidelines (safety rules,
procedures). Compliance to operational requirements especially in respect to the environment and usage of tools with this product must be observed. The 3M group
(which cannot verify or control those elements) would not be held responsible for the consequences of any violation of these rules which remain external to its decision
and control. Warranty conditions for 3M products are determined with the sales contract documents and with the mandatory and applicable clause, excluding any
other warranty or compensation. Respiratory Protection is only effective if it is correctly selected, fitted and worn throughout the time when the wearer is exposed to
respiratory contaminants. 3M offers advice on the selection of products, and training in the correct fitting and usage.
For more information on 3M products and services please contact 3M.
Personal Safety Division
3M Centre
Cain Road, Bracknell 3M and Cool Flow are trademarks of 3M Company.
Berkshire RG12 8HT Please recycle. Printed in the United Kingdom.
© 3M 2022. All rights reserved.
www.3M.co.uk/respiratory Version 7500.2
