Technical Submittal

CONCURE DPM

Al Gurg Fosroc CO.LLC

P O Box 657, Dubai U.A.E.
Tel : 04 2039699, Fax : 04 2859649
www.fosroc.com
 CONTENTS

section 1 Submission Summary

Company Introduction

section 2 ISO Certification

Trade License

section 3 Technical Data Sheet

Method Statement

section 4 Material Safety Data Sheet

Section 5 Independent Test Certification

section 6 Job references

Company Introduction
 SUBMISSION SUMMARY

Summary

Fosroc’s range of products offer the following key advantages :

▪ Technology developed to match application criteria

▪ High durability - long service life

▪ Full compatibility between systems

▪ Excellent track record in middle east conditions

In terms of this submission, points of note include the following :

▪ Technical datasheet

▪ Independent test certificates

▪ Job references and approvals of previous applications

The other main benefits of choosing Fosroc include :

▪ Products manufactured by an ISO 9001, quality-assured manufacturer

▪ Full range of complimentary products to ensure a compatible system

▪ Products manufactured, and fully supported, locally in the UAE

▪ Experienced, local applicators available

▪ Additional training available for main contractor’s supervisory staff to ensure

that the correct installation techniques are observed throughout
 constructive solutions

Al Gurg Fosroc
The company was founded as a joint venture in 1975 between HE Easa Saleh Al Gurg
and Fosroc International. Al Gurg Fosroc is the first construction chemicals company to
establish a manufacturing base in the region, and presently serves the markets of the
U. A. E., Kuwait, Bahrain, Oman and other Fosroc companies worldwide.
Fosroc is one of the world's leading manufacturers of advanced technology products for
the construction and refurbishment industries.
For over 45 years, Al Gurg Fosroc is widely recognised as the market leader in concrete
repairs and protection, in particular; and has built a substantial reputation in a wide
range of product fields: Admixtures - Concrete repair and protection - Joint fillers
and sealants -Waterproofing - Protective coatings - Surface treatments -
Waterstops - Grouts and anchors – Flooring – Electrochemical products and
services.
Fosroc's success is built on a powerful combination of market knowledge, technical
resource, manufacturing expertise and problem-solving capabilities. The company
follows a policy of detailed product research and development providing high quality
products and long-term solutions.
The company has been the first construction materials manufacturing company to
introduce specification and AutoCAD services.
Al Gurg Fosroc's products are guaranteed for quality, but they must be applied correctly
and consistently to benefit from a long service life. To ensure this success, Al Gurg
Fosroc has introduced a Contracts and Application Department. This ensures that the
technical product knowledge is transpired to the applicators and the availability of the
local technical support center ensures that the correct application techniques are
followed.
Al Gurg Fosroc's commitment to total quality management system had lead to ISO 9002
certification in December 1994 - the first construction chemicals company in the Gulf
region to achieve this prestigious award. To keep up with the present market demands,
Al Gurg Fosroc has chosen the policy of continuous improvement, which led to
ISO 9001:2015 certification.
Al Gurg Fosroc was awarded the ISO 14001 certification in 1996 making it the first
construction chemicals company and the third company in any sector in the Gulf region
to receive this award.
As a clear indication of continual improvement in safety, quality and environmental
standards, Al Gurg Fosroc was awarded the OHSAS 18001 certification in October
2004. Currently updated to ISO 45001:2018.
Al Gurg Fosroc has a state of the art production unit, which has an output exceeding
160,000 metric tons per annum.
www.fosroc.com

Al Gurg Fosroc LLC

Post Box 657, Dubai
United Arab Emirates telephone: fax: email:
(+9714) 2039699 (+9714) 2859649 agf@fosroc.com
www.fosroc. com
Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai
ISO Certificate
Trade License
 ‫رخصة صناعية‬
‫‪Industrial License‬‬
‫تفاصيل الرخصة ‪License Details /‬‬
‫‪License No.‬‬ ‫‪300142‬‬ ‫رقم الرخصة‬

‫شركة القرق فوسروك (ذ‪ .‬م‪ .‬م)‬ ‫اسم الشركة‬

‫‪Company Name‬‬ ‫(‪AL GURG FOSROC CO. )L.L.C‬‬
‫شركة القرق فوسروك (ذ‪ .‬م‪ .‬م)‬ ‫السم التجارى‬
‫‪Trade Name‬‬ ‫(‪AL GURG FOSROC CO. )L.L.C‬‬

‫‪Legal Type‬‬ ‫(‪Limited Liability Company)LLC‬‬ ‫ذات مسئولية محدودة‬ ‫الشكل القانونى‬
‫‪Expiry Date‬‬ ‫‪09/03/2024‬‬ ‫تاريخ النتهاء‬ ‫‪Issue Date‬‬ ‫‪30/10/1974‬‬ ‫تاريخ الصدار‬

‫® ‪D&B D-U-N-S‬‬ ‫‪561643177‬‬ ‫الرقم العالمي‬ ‫‪Main License No.‬‬ ‫‪300142‬‬ ‫رقم الرخصة الم‬
‫‪No.‬‬
‫‪Register No.‬‬ ‫‪41541‬‬ ‫رقم السجل التجارى‬ ‫‪DCCI No.‬‬ ‫‪10278‬‬ ‫عضوية الغرفة‬

‫الطراف ‪License Members /‬‬

‫الحصص ‪Share /‬‬ ‫الصفة ‪Role /‬‬ ‫الجنسية ‪Nationality /‬‬ ‫السم ‪Name /‬‬ ‫رقم الشخص‪No./‬‬

‫مدير ‪Manager /‬‬ ‫الردن ‪Jordan /‬‬ ‫منار صلح سعيد جمهور‬ ‫‪496716‬‬
‫‪MANAR SALAH SAID JAMHOUR‬‬

‫نشاط الرخصة التجارية ‪License Activities /‬‬

‫‪Adhesives Manufacturing‬‬ ‫صناعة مواد اللصق‬
‫‪Construction Chemicals Manufacturing‬‬ ‫صناعة المواد الكيماوية لغراض البناء‬
‫‪Insulation Materials Manufacturing‬‬ ‫صناعة المواد العازلة‬
‫‪Fire Resistant & Retardant Materials Manufacturing‬‬ ‫صناعة المواد المقاومة والمانعة لنتشار الحريق‬
‫العنوان ‪Address /‬‬
‫‪Phone No‬‬ ‫‪971-4-6858606‬‬ ‫تليفون‬ ‫‪P.O. Box‬‬ ‫‪657‬‬ ‫صندوق بريد‬
‫‪Fax No‬‬ ‫‪971-4-2859649‬‬ ‫فاكس‬ ‫‪Parcel ID‬‬ ‫‪215-357‬‬ ‫رقم القطعة‬
‫‪Mobile No‬‬ ‫‪971-50-6407901‬‬ ‫هاتف متحرك‬ ‫البريد اللكتروني ‪Email /‬‬

‫ملك الشيخ مانع بن خليفه بن سعيد ال مكتوم ‪ -‬ام رمول ‪ P215-357UNIT7‬مستودع رقم‬

‫الملحظات ‪Remarks /‬‬

‫تغيير المدير ‪.10/3/2019‬‬
‫تم نقل الموقع بتاريخ ‪15/04/2019‬‬
‫(استيراد وتصدير) حسب انشطة الرخصه‬

‫‪Print Date‬‬ ‫‪10/03/2023‬‬ ‫‪12:45‬‬ ‫تاريخ الطباعة‬ ‫‪Receipt No.‬‬ ‫‪14890100‬‬ ‫رقم اليصال‬
‫يمكنك الن تجديد رخصتك التجارية من خلل الرسائل النصية القصيرة‪ ،‬أرسل رقم الرخصة إلى ‪( 6969‬دو‪/‬اتصالت) للحصول‬
‫على اذن الدفع‪.‬‬ ‫‪Get FREE access to‬‬
‫‪Zoho One for the first‬‬
‫‪Now you can renew your trade license by sending a text message )SMS(. Send your trade‬‬ ‫‪year‬‬
‫‪license number to 6969 )Du/ Etisalat( to receive payment voucher.‬‬ ‫احصل على زوهو ون مجانا (‬
‫للسنة الولى‬
‫‪Zoho.com/det‬‬

‫وثيقة إلكترونية معتمدة وصادرة بدون توقيع من دائرة القتصاد والسياحة في دبي ‪.‬لمراجعة صحة البيانات الواردة في الرخصة يرجي مسح رمزالستجابة السريعة‬
‫‪this is a certified e-document issued without signature by the department of Economy and Tourism .Kindly Scan the QR Code to‬‬
‫‪Verify the certificate‬‬
License no. 300142 300142 ‫رقم الرخصة‬

Membership no. 10278 10278 ‫رقم العضوية‬

Registration no. 41541 41541 ‫رقم السجل التجاري‬

Trade Name AL GURG FOSROC CO. (L.L.C) (‫ م‬.‫ م‬.‫شركة القرق فوسروك )ذ‬ ‫السم التجاري‬

Legal Status Limited Liability Company(LLC) ‫ذات مسئولية محدودة‬ ‫الشكل القانوني‬

Activity Insulation Materials Manufacturing ‫صناعة المواد العازلة‬ ‫نوع النشاط‬

Adhesives Manufacturing ‫صناعة مواد اللصق‬
Construction Chemicals ‫صناعة المواد الكيماوية لغراض البناء‬
Manufacturing ‫صناعة المواد المقاومة والمانعة لنتشار‬
Fire Resistant & Retardant ‫الحريق‬
Materials Manufacturing

Member Since 30/10/1974 30/10/1974 ‫تاريخ النتساب‬

Date of Issue 30/10/1974 30/10/1974 ‫تاريخ الصدار‬

Expiry Date 09/03/2024 09/03/2024 ‫تاريخ النتهاء‬

Technical data sheet
 Fosroc Concure DPM constructive solutions

Rubberised bitumen emulsion curing compound and

foundation protective coating

Uses Properties

A cold applied rubberised bitumen membrane for use as a

Drying time : 3 hours @ 20ºC
curing compound and which provides a permanent damp
Overcoating time : 3.5 hours minimum
proof membrane and protective coating for concrete. It will
BS7542-92 : Curing efficiency > 75%
allow the concrete to hydrate efficiently while at the same
time providing a lasting protection against aggressive salts
Instructions for use
that may be present in ground water.
Preparation
Advantages
All surfaces must be clean and free from dirt, stains, oils,
 Improved curing of concrete, enhances cement hydra- grease or form coating which may otherwise prevent adhe-
tion and provides a more durable concrete. sion of Concure DPM to the concrete. All loosely adhering
particles must be removed.
 Easy to use - single component only requiring stirring
before use. No heating is required. Application

 Safe to use - water based, containing no harmful sol- Concure DPM should be well stirred before use. Applica-
vents. No risk of fire. tion should be made to the surface of concrete by brush
or squeegee at a rate of 6m2 per litre per coat. Two coats
 Chemical resistance - resists attack from chlorides and
should be applied, allowing the first coat to dry completely
sulphates in ground water.
before applying the second. The second coat should be
applied at right angles to the first. All applications should be
Standards compliance
continued up verticals to existing damp proof course. En-
Concure DPM complies with the coating ability and water sure that the membrane is not punctured or damaged during
resistance requirements of AASHTO M 140. any subsequent operations.

Overcoating
Description
Where slab surface is to receive a render or plaster finish a
Concure DPM is a rubber reinforced bitumen emulsion
keyed surface should be formed by gritting the second coat
based curing compound. When first applied to a fresh ce-
of Concure DPM with clean dry sand. Allow a minimum dry-
mentitious surface the product forms a dark brown continu-
ing period of 48 hours before plastering, rendering or laying
ous non-penetrating coating.
of a floor screed. Damaged areas of Concure DPM can be
This coating dries to form a black flexible continuous film readily overcoated to restore the continuity of the membrane.
which provides a barrier to moisture loss ensuring more
Cleaning
efficient cement hydration, improved durability and reduced
shrinkage. It then remains in place providing a permanent All equipment should be cleaned immediately after use.
damp proof membrane which resists the passage of aggres- Concure DPM can be removed with clean water while wet.
sive salts that are present in ground water, providing lasting However, once the material has dried, it can only be re-
protection to the concrete. moved with Fosroc Solvent 102*.

Design criteria Technical support

Concure DPM is designed for application in two coats Fosroc provides a technical advisory service for on-site as-
to achieve a total dry film thickness of approximately sistance and advice on admixture selection, evaluation trials
100 microns. and dispensing equipment. Technical data and guidance
can be provided for admixtures and other products for use
with fresh and hardened concrete.
Concure DPM
Fosroc Concure DPM

Estimating Health and safety

Supply Concure DPM and Fosroc Solvent 102 should not be swal-
Concure DPM : 20 & 200 litre drums lowed or allowed to come into contact with skin and eyes.
Fosroc Solvent 102 : 5 litre cans Avoid inhalation of vapours and ensure adequate ventilation.
Suitable protective gloves and goggles should be worn.
Coverage
Concure DPM : 6.0 m2/litre Some people are sensitive to resins and solvents. Barrier
@ 165 micron wft per coat creams such as Kerodex Antisolvent or Rozalex Antipaint
provide additional skin protection. Should accidental skin
Note: Coverage rates outside this recommended range may
contact occur remove immediately with a resin removing
be used if necessary and suitable to meet specific
cream such as Kerocleanse Standard Grade Skin Cleanser
requirements. Contact the Fosroc Technical Service
or Rozaclens Industrial Skin Cleanser, followed by washing
department for advice in such cases.
withsoap and water - do not use solvent. In case of contact
with eyes rinse immediately with plenty of clean water and
Storage
seek medical advice. If swallowed seek medical attention
Shelf life immediately - do not induce vomiting.

Concure DPM and Fosroc Solvent 102 have a shelf life of 6 For further information consult the Material Safety Data
months minimum if kept in a dry store between 5ºC and 30ºC Sheet available for this product.
in the original, unopened containers.
Fire
Storage conditions
Concure DPM is non flammable. Fosroc Solvent 102 is
Store Concure DPM at temperatures between 5ºC and 35ºC flammable. Keep away from sources of ignition. No smok-
in unopened original containers. Freezing or prolonged ex- ing. In the event of fire, extinguish with CO2 or foam. Do nut
posure to direct heat or direct sunlight must also be avoided. use a water jet.
Storage outside these guidelines will impair shelf life. Do not
Flash point
use if evaporated or thickened.
Fosroc Solvent 102 : 33ºC

Precautions
Cleaning and disposal

Spillages of Concure DPM should be absorbed onto sand,

earth or vermiculite and transferred to suitable containers.
The disposal of excess of waste material should be carried
out in accordance with local legislation under the guidance of
the local waste regulatory authority.

* Denotes the trademark of Fosroc International Limited

†
See separate data sheet

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com

www.fosroc.com

UAE/0320/08/D
Method statement
Method statement constructive solutions

Concure DPM

Section A : General Comments

l Comments

High temperature working

It is suggested that, for temperatures above 35³C, the following guidelines are adopted as good
working practice:

(i) Store unmixed materials in a cool (preferably temperature controlled) environment, avoiding
exposure to direct sunlight.
(ii) Keep equipment cool, arranging shade protection if necessary. It is especially important to
keep cool those surfaces of the equipment which will come into direct contact with the material
itself.
(iii) Try to avoid application during the hottest times of the day, arrange temporary shading as
necessary.
(iv) Make sufficient material, plant and labour available to ensure that application is a continuous
process.

Equipment

It is suggested that the following list of equipment is adopted as a minimum requirement.

Protective clothing : Protective overalls
: Good quality gloves, goggles and face mask

Application equipment : Brush or Squeegee

Application - points of note

Fosroc operates a policy to encourage the use, where possible, of approved or licensed applicators.
This ensures that repairs are completed satisfactorily so that the long term performance of the
materials is assured. For contractors who wish to apply the materials themselves Fosroc is also able
to offer technical assistance and training, either on-site or at its Training Centre in Dubai.

Al Gurg Fosroc
LLC
Post Box 657, Dubai telephone: fax: email:
United Arab Emirates (+9714) 2039699 (+9714) 2859649 agf@fosroc.com

www.fosroc.com Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai
 constructive solutions

Section B : Application Method

1.0 Preparation

1.1 The concrete surface should be fresh and free of surface water. Please ensure that there is
no formations of bleed water prior to commencing application.

2.0 Application

2.1 Use brush or squeege for applying Concure DPM.

2.2 Stir the material well before commencing application. By stirring, there should be an even
dispersal of the pigment.

2.3 Two coats should be applied, with the first coat allowed to dry prior to commencing
application of the second coat. Apply the second coat at right angle to the first coat
application.

2.4 Care should be taken that the surface is not trafficked until the membrane dries completely
and the concrete attains it’s trafficable strength.

3.0 Overcoating

3.1 Where the substrate is to receive a plaster or render, the second coat of Concure DPM
membraned must be gritted with clean and dry sand.

3.2 Damaged areas of Concure DPM can be readily overcoated.

3.3 Allow 48 hours prior to commencing plastering, rendering or laying of flooring screed.

4.0 Cleaning

4.1 Cleaning with water will remove the Concure DPM from the tools and equipment.

4.2 Once Concure DPM has hardened, clean the tool’s and equipment’s with Fosroc Solvent
102.

Section C : Approval and variations

This method statement is offered by Fosroc as a ‘standard proposal’ for the application of Concure
DPM. It remains the responsibility of the Engineer to determine the correct method for any given
application.

Where alternative methods are to be used, these must be submitted to Fosroc for approval, in
writing, prior to commencement of any work. Fosroc will not accept responsibility or liability for
variations to the above method statement under any other condition.

Page 2 of 2
MSDS
Revision date: 21/06/2016 Revision: 1

SAFETY DATA SHEET

CONCURE DPM

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name CONCURE DPM

Product number 1201000AE1, 1201002AE1

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Curing agent.

1.3. Details of the supplier of the safety data sheet

Supplier Al Gurg Fosroc LLC
PO Box 657
Dubai
United Arab Emirates
+ 971 4 2858606

1.4. Emergency telephone number

Emergency telephone +97142039699 (08:00 to 16:30) // +971506258232 (16:30 to 08:00)GMT+4

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification
Physical hazards Not Classified

Health hazards Elicitation - EUH208 Asp. Tox. 1 - H304

Environmental hazards Not Classified

Classification (67/548/EEC or -
1999/45/EC)

2.2. Label elements

Pictogram

Signal word Danger

Hazard statements H304 May be fatal if swallowed and enters airways.

EUH208 Contains FORMALDEHYDE. May produce an allergic reaction.

Precautionary statements P301+P310 IF SWALLOWED: Immediately call a POISON CENTER/doctor.

P331 Do NOT induce vomiting.
P405 Store locked up.
P501 Dispose of contents/container in accordance with national regulations.

1/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

Contains DISTILLATES (PETROLEUM), HYDROTREATED LIGHT; KEROSINE - UNSPECIFIED,

FORMALDEHYDE

2.3. Other hazards

This product does not contain any substances classified as PBT or vPvB.

SECTION 3: Composition/information on ingredients

3.2. Mixtures

DISTILLATES (PETROLEUM), HYDROTREATED LIGHT; 60-100%

KEROSINE - UNSPECIFIED
CAS number: 64742-47-8 EC number: 265-149-8

Classification
Asp. Tox. 1 - H304

FORMALDEHYDE <1%
CAS number: 50-00-0 EC number: 200-001-8

Classification
Acute Tox. 4 - H302
Acute Tox. 3 - H311
Acute Tox. 3 - H331
Skin Corr. 1B - H314
Eye Irrit. 2 - H319
Skin Sens. 1 - H317
Carc. 2 - H351

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation Move affected person to fresh air at once. Get medical attention. Move affected person to
fresh air and keep warm and at rest in a position comfortable for breathing. When breathing is
difficult, properly trained personnel may assist affected person by administering oxygen.

Ingestion Do not induce vomiting. Never give anything by mouth to an unconscious person. Do not
induce vomiting. If vomiting occurs, the head should be kept low so that vomit does not enter
the lungs. Give plenty of water to drink. Get medical attention immediately. Move affected
person to fresh air and keep warm and at rest in a position comfortable for breathing.

Skin contact Remove contaminated clothing. Wash skin thoroughly with soap and water. Get medical
attention promptly if symptoms occur after washing.

Eye contact Remove any contact lenses and open eyelids wide apart. Remove any contact lenses and
open eyelids wide apart. Continue to rinse for at least 15 minutes. Continue to rinse for at
least 15 minutes and get medical attention.

4.2. Most important symptoms and effects, both acute and delayed
General information Get medical attention promptly if symptoms occur after washing.

4.3. Indication of any immediate medical attention and special treatment needed
Notes for the doctor Treat symptomatically.

2/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media The product is not flammable. Use fire-extinguishing media suitable for the surrounding fire.

5.2. Special hazards arising from the substance or mixture

Specific hazards Non-flammable and non-explosive

5.3. Advice for firefighters

Protective actions during Fight fire with normal precautions from a reasonable distance.
firefighting

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Wear personal protective clothing and equipment, see Section 8.

6.2. Environmental precautions

Environmental precautions Do not discharge into drains or watercourses or onto the ground.

6.3. Methods and material for containment and cleaning up

Methods for cleaning up Wear suitable protective equipment, including gloves, goggles/face shield, respirator, boots,
clothing or apron, as appropriate. Absorb in vermiculite, dry sand or earth and place into
containers. Avoid the spillage or runoff entering drains, sewers or watercourses.

6.4. Reference to other sections

Reference to other sections See Section 11 for additional information on health hazards.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions Avoid spilling. Provide adequate ventilation. Avoid inhalation of vapours. Use approved
respirator if air contamination is above an acceptable level. Avoid skin and eye contact.

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Store in tightly-closed, original container in a dry, cool and well-ventilated place.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure Controls/personal protection

8.1. Control parameters

Occupational exposure limits
FORMALDEHYDE
Long-term exposure limit (8-hour TWA): WEL 2 ppm 2,5 mg/m³
Short-term exposure limit (15-minute): WEL 2 ppm 2,5 mg/m³
WEL = Workplace Exposure Limit

FORMALDEHYDE (CAS: 50-00-0)

DNEL Workers - Inhalation; Long term systemic effects: 9 mg/m³

8.2. Exposure controls

3/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

Protective equipment

Appropriate engineering Provide adequate general and local exhaust ventilation.

controls

Eye/face protection The following protection should be worn: Chemical splash goggles.

Hand protection Use protective gloves.

Other skin and body Wear appropriate clothing to prevent any possibility of liquid contact and repeated or
protection prolonged vapour contact.

Hygiene measures Do not smoke in work area. Wash hands at the end of each work shift and before eating,
smoking and using the toilet. Promptly remove any clothing that becomes contaminated.
Wash promptly with soap and water if skin becomes contaminated. Use appropriate skin
cream to prevent drying of skin. When using do not eat, drink or smoke.

Respiratory protection No specific recommendations. Respiratory protection may be required if excessive airborne
contamination occurs.

SECTION 9: Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

Appearance Liquid

Colour Brown to black

Odour not significant

Odour threshold Not applicable.

pH 12

Melting point Not available.

Initial boiling point and range Not determined.

Flash point Not available.

Evaporation rate Not determined.

Evaporation factor Not determined.

Flammability (solid, gas) Not determined.

Upper/lower flammability or Not determined.

explosive limits

Other flammability Not determined.

Vapour pressure Not determined.

Vapour density Not determined.

Relative density 1.01

Bulk density Not determined.

Solubility(ies) Soluble in water

Partition coefficient Not determined.

Auto-ignition temperature Not determined.

4/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

Decomposition Temperature Not determined.

Viscosity 20-25 P @ 25°C

Explosive properties Not considered to be explosive.

Explosive under the influence Not considered to be explosive.

of a flame

Oxidising properties Not determined.

9.2. Other information

Other information No additional information.

SECTION 10: Stability and reactivity

10.1. Reactivity
Reactivity No dangerous reactions known if used as directed.

10.2. Chemical stability

Stability Stable at normal ambient temperatures.

10.3. Possibility of hazardous reactions

Possibility of hazardous Hazardous reactions will not occur under normal transport or storage conditions.
reactions

10.4. Conditions to avoid

Conditions to avoid Avoid contact with the following materials: Acids. Oxidising agents.

10.5. Incompatible materials

Materials to avoid Avoid contact with strong oxidising agents.

10.6. Hazardous decomposition products

Hazardous decomposition Fire creates: Toxic gases/vapours/fumes of: Carbon monoxide (CO). Carbon dioxide (CO2).
products

SECTION 11: Toxicological information

11.1. Information on toxicological effects

Acute toxicity - dermal
ATE dermal (mg/kg) 187,500.0

Acute toxicity - inhalation

ATE inhalation (gases ppm) 437,500.0

Inhalation Prolonged inhalation of high concentrations may damage respiratory system.

Ingestion Harmful: may cause lung damage if swallowed. Pneumonia may be the result if vomited
material containing solvents reaches the lungs.

Skin contact Product has a defatting effect on skin. May cause allergic contact eczema.

Eye contact May cause severe eye irritation.

Toxicological information on ingredients.

FORMALDEHYDE

Acute toxicity - oral

5/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

Acute toxicity oral (LD₅₀ 800.0

mg/kg)

Species Rat

ATE oral (mg/kg) 800.0

Acute toxicity - dermal

ATE dermal (mg/kg) 300.0

Acute toxicity - inhalation

Acute toxicity inhalation 31.7

(LC₅₀ gases ppmV)

Species Rat

ATE inhalation (gases 700.0

ppm)

SECTION 12: Ecological Information

12.1. Toxicity
Ecological information on ingredients.

FORMALDEHYDE

Acute toxicity - fish LC₅₀, 24 hours: 31.8 mg/l, Freshwater fish

Acute toxicity - aquatic EC₅₀, 48 hours: 5.8 mg/l, Freshwater invertebrates

invertebrates

12.2. Persistence and degradability

Persistence and degradability Not determined.

12.3. Bioaccumulative potential

Bioaccumulative potential Not available.

Partition coefficient Not determined.

12.4. Mobility in soil

Mobility Not available.

12.5. Results of PBT and vPvB assessment

Results of PBT and vPvB This product does not contain any substances classified as PBT or vPvB.
assessment

12.6. Other adverse effects

Other adverse effects Not available.

SECTION 13: Disposal considerations

13.1. Waste treatment methods

Disposal methods Dispose of waste to licensed waste disposal site in accordance with the requirements of the
local Waste Disposal Authority.

SECTION 14: Transport information

6/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

General The product is not covered by international regulations on the transport of dangerous goods
(IMDG, IATA, ADR/RID).

Road transport notes Not classified.

Rail transport notes Not classified.

Sea transport notes Not classified.

Air transport notes Not classified.

14.1. UN number
Not applicable.

14.2. UN proper shipping name

Not applicable.

14.3. Transport hazard class(es)

No transport warning sign required.

14.4. Packing group

Not applicable.

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

No.

14.6. Special precautions for user

Not applicable.

14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulations Rivers (Prevention of Pollution) Act 1961.
Control of Pollution (Special Waste) Regulations 1980 (as amended).
The Chemicals (Hazard Information and Packaging for Supply) Regulations 2009 (SI 2009
No. 716).

Guidance Workplace Exposure Limits EH40.

Introduction to Local Exhaust Ventilation HS(G)37.
CHIP for everyone HSG228.
Approved Classification and Labelling Guide (Sixth edition) L131.

15.2. Chemical safety assessment

Not available.

SECTION 16: Other information

Revision comments NOTE: Lines within the margin indicate significant changes from the previous revision.

Revision date 21/06/2016

Revision 1

7/8
Revision date: 21/06/2016 Revision: 1

CONCURE DPM

SDS number 23938

Hazard statements in full EUH208 Contains FORMALDEHYDE ...%. May produce an allergic reaction.
H302 Harmful if swallowed.
H304 May be fatal if swallowed and enters airways.
H311 Toxic in contact with skin.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H331 Toxic if inhaled.
H351 Suspected of causing cancer.

8/8
Test report
Job reference