Parking on 2 levels with pit

Kipparker N 3000 comfort S/D

The classic even more user friendly

with less platform inclination

Made in Germany
Areas of application

residential buildings, single garages above ground and prefabricated garages

Both platforms
free space 135 25 free space for gate
are inclined 140 115 25 free space for gate

Load per platform

max. 2000kg 90

Load per wheel

max. 500kg
295

295

200 (210)
to GaVo
,5°
pprox. 4
incline a
Dimensions in cm
entrance 300 max. 1%
10 10

slope
,5°
pprox. 6

min 18, B 25
incline a

155
150

concrete
wall opening 10 x 10 for
hydraulic and electrical lines
300
in case of intermadiate walls 530 (525 available on request)
2% incline to DIN 1045-1
drainage channel 10 x 10
+3 with collecting pit 50 x 50 x 20
• Tolerances to construction dimensions 0.

• Optionally: 155 cm pit at front; 160 cm pit at rear (pit edge), 295cm inside height

Vehicle Data

8 162 65 55 90 8 162 115

10
25 20 15
HO HU
46
150* 46
154* 14
56
22 60 20 56 22 27
38 14
38 60
90 max. 290 120
90 max. 290 120
500 500

max. car width 190cm, max. load per platform 2000kg, max. load of wheel 500kg

*HO platform above *HU platform below

Height of the car in HO is 150 cm. HO is not suitable Height of the car in HU is 154cm. Neither the
for station wagons, low clearance cars or tuned cars standard or the extra height version is suitable
(spoilers or roker rail). In the extra height version with for station wagons, low clearance cars or tuned
310 cm inside height station wagons can park in the cars (spoilers or roker rail). For these vehicles we
above level. recommend the parking systems Liftparker N 4400
and N 4600 with horizontal accessible platforms.

Note: The total car height including roof rail and antenna fixture must not exceed the mentioned max. height.
Width dimensions • Garages
All dimensions are minimum dimensions. All dimensions in cm. Tolerances to the German Norm VOB part C (DIN
18330, 18331) and DIN 18202 are to be considered.
Note: Dimensions do not include the dimensions of the hydraulic unit. Dimensions of the hydraulic unit and the
switch cabinet shown in page 4 below, are to be considered in the planning.

partition walls

S - system S - system D - system S - system

A1 driving lane according

A1 A1
to local requirements
S-system for 2 cars D-system for 4 cars D- and S-system for 6 cars

width A1 260 270 280 width A1 490 500 510 520 530 width A1 750 780 810

width* 230 240 250 width* 460 470 480 490 500 width* 460/230 470/240 480/250
* gives clear platform width * gives clear platform width * gives clear platform width

building pillars inside of the pit

S S
D D D E D E
min. 15 min. 15 min. 15
max.
max. 100 max. 100
100 driving lane

B1 B2 B1 B2 B1 B2 according to
local requirements
S-system for 2 cars D-system for 4 cars D- and S-system for 6 cars

width B1 255 265 275 width B1 485 495 505 515 525 width B1 745 775 805

width B2 250 260 270 width B2 475 485 495 505 515 width B2 735 765 795

width* 230 240 250 width* 460 470 480 490 500 width* 230+460 240+480 250+500
* gives clear platform width * gives clear platform width * gives clear platform width

building pillars in front of the pit

S S D D
D S D S

min. 20 min. 20 min. 20

driving lane
according to
C1 C2 C1 C2 C1 C2
local requirements
S-system for 2 cars D-system for 4 cars D- and S-system for 6 cars

width C1 250 260 270 width C1 480 490 500 510 520 width C1 740 770 800

width C2 240 250 260 width C2 470 480 490 500 510 width C2 730 760 790

width* 230 240 250 width* 460 470 480 490 500 width* 230+460 240+480 250+500

* gives clear platform width * gives clear platform width * gives clear platform width
Features in the scope of delivery

Scope of supply
S/D-systems with 2 platforms, 2 columns, 2 hydraulic
cylinders and hydraulic block

Width of parking space

Width of parking space 230cm and depth of pit 155/150cm
1 key switch as standard
2 emergency stop

Safety devices
Key switch • synchronizing device for safe operation even with
Key switch incl. emergency stop, dead man´s unequal load distribution on the platform
control type with brief operating instructions • entering wedge for easy drive-in and parking
and wiring to hydraulic unit. • locking device prevents lowering by pipe breakage
• fixation of the car parking systems and hydraulic
unit with HD-anchors, wiring and impact dowels
• railings to avoid risk of falling onto the platform,
insofar as necessary
Note: Safety guards against shearing and squeezing
have priority and must be provided by the Buyer.

Protection against corrosion

Corrosion protection version „Classic“ of driving plates
by continuous line-galvanizing to DIN EN 10142/10143.
Hydraulic unit Corrosion protection version „Classic Plus“ of driving
Hydraulic unit “Silencio“ with tubing and plates by line-galvanizing to DIN EN 10142/10143
wiring to the installation. The oil submerged (depending on the market specific needs zinced and
motor “Silencio“ is extremely quiet and smooth powder coated sheet metal included in the scope of
running. The motor-pump assembly is sound supply).
absorbent.

Location
• between or behind two systems in the pit
on a 2 m high support, see picture above
• if there is no space between or behind the
systems – wall-mounted
• single systems: power supply placed directly
on the lower platform, in the front left side

Dimensions incl. switch cabinet

• 1 – 2 systems: 65 cm x 25 cm x 60cm
• 3 – 5 systems: 115cm x 25 cm x 60 cm
Driving plates
The hydraulic unit can be used for up to 5 Driving plates as trapezoidal sheet plates as standard,
Car Parking Systems. options see “Extra Equipment“.
Extra Equipment and Options

Width of parking space

• button lifting Width of parking space 240cm and 250cm is recommended
• button lowering for even more vehicle comfort
• emergency stop
• key switch with
key interlock
Vehicle weight
Optional vehicle weight: 2500kg – not by inclined parking
Berlin control system/Fire brigade spaces. We recommend to use for these vehicles our
Interlocked key switch, removal of the key solutions Liftparker N 4400 and N 4600 with horizontal
only in the upper basic position. accessible platforms.

Additional sound insulation

• structure-borne noise package to comply with DIN 4109
and adherence to sound insulation-measure Rw ´57
• sound insulatin hood to minimize airborne sound

Hydraulic
• HVLP-oil for high fluctuations in temperature

Installation of garage gates

• ramp when door facing is not available to install the door
slide rail, pit length must be 535cm, at the minimum
Driving plates
Alu-bulb-plate in the walking area even more Protection against corrosion
user friendly when walking and driving. • Corrosion protection version „Premium“ of driving
plates by individual piece-galvanizing to DIN ISO 1461
• Corrosion protection version „Premium Plus“ of driving
plates by individual piece-galvanizing to DIN ISO 1461
and coating of the top surfaces

Tips
• We recommend a maintenance contract.
• Attendance and cleaning according to recommendations
or in regular intervals.

Catwalks
Positioning on the left side of the parking
space even more comfortable, when walking
to the driver´s door. 1,5 mm zinced sheet,
surface area coined. The catwalks are screwed
to the driving plates, available with corrosion
protection version „Classic“ or „Classic Plus“.
Dimensions approx. 350 cm x 31/41cm (L x W)
Interfaces to be performed by the Buyer

Foundation
Foundation works exactly to size, clean and dry is to be completed by the start of the installation. Bonded anchors
for high foundation requirements shall be provided if neccessary, available also as option.

Foundation plan F1
F1
F2 F2
single-system double-system F3 F3
F1 13 kN 30 kN F4 F4
F2
F2 +/- 2 kN +/- 2 kN F3
F6
F3 2 kN 7 kN
F5 F5
F4 8 kN 15 kN
F5 F4 F1
F5 10 kN 10 kN
F6 F6
F6 +/- 5 kN +/- 10 kN
10 10

The pit must be executed in compliance with the designated forces. The forces and loads are transfered to the
foundation by bearing plates with an area of 150cm². The bearing plates are fixed with metal expansion anchors.
The drill hole depth is approx. 14 cm. All walls in the pit below the entrance level must be of concrete.

Electrical Data General costumers duties

• supply line to main switch 5 x 2,5mm² or according • level surface (L x W) 50cm x 20cm to attach the
to local requirements, fuse protection 3 x 16 amp, control panel, close to the system, outside the
slow platform area
• lockable main switch, near to hydraulic unit but • safeguarding according to DIN EN 294
outside of the pit, completed at the beginning of • lighting according to DIN 67528, illumination of
installation, height approx. 180 cm above entrance parking lots and buildings for parking
level (color requirements to EN 60204-1, 10.7.4, • at the edge of the pit a 10cm wide, yellow-black
color red) marking according to ISO 3864
• capacity of the hydraulic unit: 400volt, 50 hz, • wall opening 10cm x 10cm for hydraulic and
threephase motor 3,0 kW electrical lines in case of intermadiate walls
• electrical potential equalisation (foundation • compliance with installation requirements as per
grounding steel-construction to VDE 0100 T410) quotation

lockable main switch safeguarding to DIN EN 294 marking pit edge

Width dimensions • Garages with doors

single system for 2 cars

TA = seat-engaging surface for doors

The dimensions must be agreed with

S - system S - system S - system the door manufacturer on site.

TA
TA

LB LB LB ST ST

DB DB DB

width of parking space door entrance width DB reveal LB pillar ST

5 5
230 237 12 25
5
240 250 12 25

250 250 15 30

double system for 4 cars

D - system D - system D - system

driving lane
LB LB LB ST ST
according to the
DB DB DB local requirements

width of parking space door entrance width DB reveal LB pillar ST

460 460 15 30
5
470 475 12 25

480 475 17 5 35
5
490 500 12 25

500 500 15 30
Electric Installation

2
Installation diagram 1

7 12 10

8 9
11

13

11

4
5
14 15
14

Technical modifications reserved. Modifications in the scope of supply reserved to the manufacturer. Version 21112007 · NK
Item Performance Quantity Designation Location Frequency

1 on site 1 fuse or automatic circuit in the feed cable 1 per hydr. unit
3 x 16 amp slow to DIN VDE 0100 part 430

2 on site 1 supply line 5 G 2,5 mm² or feed cable to 1 per hydr. unit
according to local requirements main switch

3 on site 1 lockable main switch near to hydraulic unit 1 per hydr. unit

4 on site each foundation earth connector corner pit floor/

10 m rear wall

5 on site 1 potential equalisation to DIN EN 60204 from foundation earth 1 per hydr. unit
connector to the system

6 Nussbaum 1 hydraulic unit with 3-phaze motor 230/400volt, 50 hz 3 kW

7 Nussbaum 1 supply line 5 G 2,5 mm² with from main switch 1 per hydr. unit
marked wires and protective conductor to hydraulic unit

8 Nussbaum 1 control line 2 x 1

9 Nussbaum 1 control element with emergency stop

10 Nussbaum 1 control line 4G1

11 Nussbaum 1 control line 4G1

12 Nussbaum 1 control line 2 x 1

13 Nussbaum 1 hydraulic valve lifting and lowering

14 Nussbaum 1 hydraulic valve lifting and lowering by installation in ranks

15 Nussbaum 1 control element for each further system

The items 6 – 15 are included in the scope of supply, unless otherwise specified in the offer/order.

Otto Nußbaum GmbH & Co. KG · Korker Str. 24 · 77694 Kehl-Bodersweier

Tel.: +49(0)78 53/8 99-0 · Fax: +49(0)78 53/ 899-114 · www.nussbaum-parking.de