Service Data Vickers®
Piston Pumps & Motors
Variable Inline Piston Units
PVB10-(F)**(Y)-30/31-*(*)(L)-1*
PVB15-(F)**(Y)-30/31-*(*)(L)-1*
MPVB10-(F)UD(Y)-30/31-*-10
Revised 2/98 I-3268-S
Compensator S/A Parts
Included in start-up
Pressure Range Compensator Spring valve (E) S/A 942157
(psi) S/A
312171 Plug
(C)350-3000 (10) 942158 239371
350-2000 (15) 263492 ‘‘O’’ Ring
(CM) 350-1500 942159 265693 248773 Pin 1276 Screw (4 req’d)
356986 Spool 293548 Body
(Torque to 25-35 lb. ft.)
O 244956 Gasket
262331 ‘‘O’’ Ring
154005 ‘‘O’’ Ring
113000 Plug 244956 Gasket
293547 Spool
354858 Body 312384 Spring
10358 Screw (4 req’d) 248829 Rod
189128 Screw (4 req’d) 7074 Plug
(Torque to 60-70 lb. in.)
NOTE
173792 ‘‘O’’ Ring Compensator and start-up valve shown
360430 Plug for L.H. shaft rotation. For R.H. rotation
Parts included in (40205 Plug - units, rotate both valves 180.
Compensator S/A F6 Models)
O CAUTION Control Pintle
CAUTION Position compensator gasket with (See Table)
Do not use back-up
small end of teardrop hole pointing 166360 ‘‘O’’ Ring
washer with new
in direction of compensator
spherical washer.
adjusting plug.
RETAINING WASHER SPRING THRUST CYLINDER ROTATING
MODEL RING WASHER BLOCK GROUP KIT
THESE PARTS ARE INCLUDED IN ROTATING GROUP KIT
PVB10-**(Y)-3*-**-1*
321703 938276
MVB10-**(Y)-3*-**-1* 247294
93509 245223 241954
PVB15-**(Y)-3*-**-1* 938273
260860
F6-PVB15-**(Y)-3*-**-1* 403858 938277
12016 Bearing
Yoke
(See table
on next
page)
1306 Screw (2 req’d)
(Torque to 75-80 lb. ft.)
PIN SPHERICAL SHOE PISTON S/A SWASH ROTATING
MODEL (3 REQ’D) WASHER PLATE KIT PLATE GROUP KIT
THESE PARTS ARE INCLUDED IN ROTATING GROUP KIT
PVB10-**(Y)-3*-**-1*
942207 938276
MVB10-**(Y)-3*-**-1* 248812 423324 275961 239077
PVB15-**(Y)-3*-**-1* 938273
941887
F6-PVB15-**(Y)-3*-**-1* 938277
NOTE Pintles
Type ‘C’ & ‘CM’ Compensator Control Parts Models
shown. See back page for manual controls. Control Other
Refer to Parts Drawing I-3243-S for ‘CVP’ Handwheel 269657
Pressure Limiting & Load Sensing Compensator Lever 269658 265425
Control. Compensator 265425
Eaton Hydraulics, Incorporated 2000
All Rights Reserved
113000 Plug Valve Plate (See table)
Included in Valve Plate S/A
942237 Piston Rod S/A Rotation plate shown for R.H.
317162 Gasket (CW) shaft rotation. Locate
1276 Screw on opposite side of valve for
(4 req’d) 227401
L.H. (CCW) rotation.
(Torque to Screw
25-35 lb. ft.)
173792 ‘‘O’’ Ring
185638 Snap Ring
INCLUDED IN
MODEL VALVE PLATE S/A
154129 ‘‘O’’ Ring PVB10-RD(Y)-3*-H/M-10 942160
Valve Plate (See Table) PVB10-LD(Y)-3*-H/M-10 942161
186580 Plug
MVB10-UD(Y)-3*-H/M-10 942162
PVB15-RD(Y)-3*-H/M-10 942163
MODEL YOKE HOUSING SCREW ROTATION PVB15-LD(Y)-3*-H/M-10 942164
PLATE
PVB10-RS(Y)-3*-C(*)-11 942165
PVB1*-*D(Y)-3*-H/M-10 325689 308327 227401 195060 PVB10-LS(Y)-3*-C(*)-11 942166
PVB1*-*S(Y)-3*C(*)/CM-11 342743 357652 227407 404751 F6-PVB15-RS(Y)-3*-C(*)-11 942167
MVB10-*D(Y)-3*-H/M-10 325689 308327 F6-PVB15-LS(Y)-3*-C(*)-11 942168
F6-PVB15-*S(Y)-3*-C*(*)-11 342743 398719 227407 404751
317239 Spring
278634 Spring
(Compensator
Models only)
250535 Seat 227401 Screw (2 req’d) 284397 Bearing
164432 Instruction Plate 119982 Retaining Ring
343573 Shaft Seal 120428 Retaining Ring
(Assemble with spring
227401 Screw (2 req’d) toward inside of unit.)
Nameplate 274382 Retainer
Model Shaft Key
*VB*-***-3* 261478 22971
*VB*-***Y-3* 270369 58303 Foot Bracket Kit FB-B-10
(Used on *VB*-(F) Models Only)
(Includes screws)
12016 Bearing 199740 Screw (2 req’d)
(Used on *VB*-(F) Models only)
167237 Pin (2 req’d)
12016 Bearing
Other Pintle F6 Model Shaft Seal Arrangement
(See table) (Replaces seal, retainer, and bearing shown above.)
199815 ‘‘O’’ Ring 398717 Face Seal Ring
166360 ‘‘O’’ Ring (Face chamfer toward bearing.)
Used on 246462 Cover 398716 Face Seal 402006 Spacer
Hand Wheel
and Lever 12278 Screw (2 req’d)
Models only.
F3 equivalent Included in
919686 Seal Kit 919682 Seal Kit
292496 Bearing
192672 ‘‘O’’ Ring
398718 Wave Washer Included in 920242
Shaft Seal Kit
Model Code
1 2 3 4 5 6 7 8 9 10 11 12 13
1 Seals 6 Rotation 10 Control Type
F3 - Multi-fluid capability
Viewing from shaft end C- 250-3000 psi (20 USgpm)
(Viton seals)
F6 - Soluble oil fluids R - Right hand (CW) 250-2000 psi (29 USgpm)
L - Left hand (CCW) CM - Pressure compensated
2 Model U - Either direction (Motors only) (Intermediate range)
(250-1500) psi 2* USgpm units
M - Motor
CVP- Pressure limiter/load sensing
P - Pump 7 Swash Plate Movement H - Handwheel
3 M - Lever
Model Type D - Both sides of center
Variable displacement, inline S - One side of center 11 Compensator Variations
piston unit (Refer to I-3260-S for more
8 Shaft detailed information.)
4 Flow rating @ 1800 rpm
Y - Long shaft (Standard) C - Adjustable maximum stop
10 - 10 USgpm (Omit for short shaft) D - Dual range (Electric control -
15 - 15 USgpm 115 volts - 60 cycle)
9 Pump Design Number DH - Dual range (Hyd. control)
5 Mounting E - Start-up valve
F - Foot bracket
(Omit for flange mount) 12 Control Options
L - Left hand location
Viewing shaft end
(Omit for right hand location.)
13 Control Design Number
Manual Lever Control Model Handwheel Control Model
*VB-*-(*)**(*)-3*-M(*)(*)-10 *VB-*-(*)**(*)-3*-H(*)(*)-10
233744 Lever n 239557 Handwheel
n 328753 Gear
Included in Drive S/A
Lever Kit 941360 n 226754 Rollpin
n 327585
Thumb
99782 Lockwasher
Screw
1450 Nut 1234 Screw
n Included in
938523 S/A
For satisfactory service life of these components, use full flow filtration to provide fluid which meets ISO cleanliness code 16/13
or cleaner. Selections from pressure, return, and in-line filter series are recommended.
Printed in U.S.A.
