TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY

Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in

Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
QUESTION BANK
Name of the Department : Electrical and Electronics Engineering

Subject Code & Name : EE8701 & HIGH VOLTAGE ENGINEERING

Year & Semester : IV & VII

UNIT I OVER VOLTAGES IN ELECTRICAL POWER SYSTEMS

PART – A
1. What are the different types of over voltages?
Lightning over voltages, Switching over voltages, and power frequency over voltages (temporary over
voltage).

2. Explain the various regions of the cloud.

The upper regions of the cloud are positively charged, whereas the lower region and the base are
predominantly negative except the local region near the base and the head which is possible.

3. What is back flash over?

When a direct lightning strike occurs on a tower, the tower has to carry huge impulse currents. If the
tower footing resistance is considerable, the potential of the tower rise to a large value, steeply with
respect to the line and consequently a flash over may take place along the insulator strings. This is
known as back flash over

4. State the parameters and the characteristics of the lightning strokes.

Amplitude of the current, the rate of rise, the probability distribution of them and the wave shapes of
the lightning voltages and currents.

5. How are attenuation and distortion caused?

Attenuation is caused due to the energy loss in the line and distortion is caused due to the inductance
and capacitance of the line.

6. State the factors influence the lightning induced voltages on transmission lines.
The ground conductivity, the leader strokes current and the corona.

7. State the attenuation and distortion of traveling waves.

The decrease in the magnitude of the wave as it propagates along the line is called attenuation. The
elongation or change of wave shapes that occur is called distortion.

8. When over voltages are generated in EHV system?

Over voltages are generated in EHV systems when there is a sudden release of internal energy stored

1
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
either in the electrostatic form or in the electromagnetic form.

9. What are the uses of shunt reactors?

Shunt reactors are (i) Used to limit the voltage rise due to the ferranti effect (ii)Used to reduce surges
caused due to sudden energizing.

10. What is a ground wire?

The Ground wire is a conductor run parallel to the main conductor of the transmission line supported
on the same tower and earthed at every equally and regularly spaced towers. It is run above the main
conductor of the line.

11. What is an expulsion gap?

Expulsion gap is a device, which consists of a spark gap together with an arc quenching device, which
extinguishes the current arc when the gap breaks over due to over voltage.

12. What is a protector tube?

It is a device, which consists of a rod or spark gap in air formed by the line conductor and its high
voltage terminal. It is mounted underneath the line conductor on a tower.

13. How is the insulation level and the protective safety margin arrived?
Selecting the risk of failure, the statistical safety factor and by firing the withstand level of any
equipment or apparatus corresponding to 90% or95% of the withstand voltage.

14. Mention the various insulation levels in a substation?

The bus bar insulation is the highest to ensure the continuity of supply in a substation. The circuit
breakers, isolators, instrument and relay transformers are given the next lower limiting level. The
power transformers are the costliest and sensitive devices and the insulation level for it is the lowest.

15. What are the various types of surge arresters used for EHV and UHV systems?
Silicon carbide arresters with spark gaps, Silicon carbide arresters with current limiting gaps and the
gapless metal oxide arresters.

16. Write the equation of surge admittance and surge impedance of the transmissionline.

where α is the attenuation constant and β is the wavelength constant.

17. Define Isokeraunic level or thunderstorm days.

It is defined as the number of days in a year when the thunder is heard or recorded in a particular
location. Often it does not distinguish between theground strokes and the cloud-to-cloud strokes.

18. A transmission line surge impedance 250 ohms is connected to a cable of surge impedance of

2
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
50 ohms at the other end, if the surge of 400 kV travels along the line to the junction point, find
the voltage build at the junction.
V”=V(2*Z2/Z1+Z2), where V=400 kV , Z1=250 ohms, Z2=50 ohms V”=400,000*(2(50)/(250+50)),
V”=133.33kV.

19. Define Lightning phenomenon.

Lightning phenomenon is a peak discharge in which charge accumulated in the cloud discharges into a
neighboring cloud or on the ground.

20. List some sources causing switching surges.

Sudden switching off of loads, short circuits and fault clearances, disconnection of unloaded
transformers, reactors.

21. What is stepped leader stroke?

Due to insufficient build of charge at the head of leader stroke comes to a halt after progressing about
50 meter and again after a short interval the streamer starts out repeating its performance with different
branches by a series of jumps.It is called as stepped leader.

22. State the sources which determine the wave shape of switching surges.
 De-energizing of transmission lines, cables, shunt capacitor, banks,etc.
 Disconnection of unloaded transformers, reactors, etc.
 Energization or reclosing of lines and reactive loads,
 Sudden switching off of loads.
 Short circuits and fault clearances.
 Resonance phenomenon like ferro-resonance, arcing grounds, etc.

23. Write down the causes of power frequency over voltages.

The main causes for power frequency and its harmonic over voltages are,
 Sudden loss of loads,
 Disconnection of inductive loads or connection of capacitive loads,
 Ferranti effect, unsymmetrical faults, and
 Saturation in transformer

24. Classify the lightning strokes.

 Cloud to cloud lightning
 Cloud to air lightning
 Intra cloud lightning
 Cloud to ground lightning
 Bolt from the blue
 Ribbon lightning

25. Why a simple spark gap cannot offer full protection against over voltages?

3
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
The spark over voltage of a rod gap depends on the atmospheric conditions. There is no current limiting
device provided so as to limit the current after spark over, and hence a series resistance is often used.
Without a series resistance, the sparking current may be very high and the applied impulse voltage
suddenly collapses to zero thus creating a steep step voltage, which sometimes proves to be very
dangerous to the apparatus to be protected, such as transformer or the machine windings.
PART –B & C
1. What are the causes for switching and power frequency over voltages? How are they
controlled in power system?
2. Explain with suitable figure the principles and functioning of (i) Expulsion Gap
(ii)Protector Tube.
3. Write short a note on (i) Rod gaps as protective devices (ii) Ground wires for protection of
overhead lines.
4. What are the mechanisms by which lightning strokes develop and induce over voltages on
overhead power lines? Give the mathematical models for lightning discharges and explain
them.
5. Explain the different theories of charge formation in clouds.
6. An underground cable of inductance 0.150 mH/km and of capacitance 0.2 µF/km is
connected to an overhead line having an inductance of 1.2 mH/km and capacitance of 0.006
µF/km. Calculate the transmitted and reflected voltage and current waves at the junction, if a
surge of 200 kV travels to the junction, (i) along the cable, and (ii)along the overhead line.
7. A long transmission line is energized by a unit step voltage 1.0 V at the sending end and is
open circuited at the receiving end. Construct the Bewley lattice diagram and obtain the value of
the voltage at the receiving end after a long time. Take the attenuation factor α = 0.8.Discuss the
step by step procedure for constructing Bewley”sLattice diagram with an example.
8. Draw the cross sectional view of valve type lightning arrester and explain its operation with
V-I characteristics.
9. What are the requirements of a ground wire for protecting power conductors against direct
lightning stroke? Explain how they are achieved in practice.
10. Explain the characteristics of switching surges with typical waveforms. Explain
why a steep fronted surge waveform are more vulnerable to insulation?
11. What are the different method employed for the lightning protection of overhead lines?
UNIT II
DIELECTRIC BREAKDOWN
PART A
1. Mention the gases used as the insulating medium in electrical apparatus?
Most of the electrical apparatus use air as the insulating medium, and in a few cases other gases such as nitrogen, carbon
dioxide, Freon and sulphur hexafluoride.

2 .What is breakdown voltage?

4
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
The maximum voltage applied to the insulation at the moment of breakdown is called the breakdown
voltage
.
3. What is ionization?
The process of liberating an electron from a gas molecule with a simultaneous production of a positive ion is called
ionization.

4. What is a Townsend’s first ionization coefficient?

Townsend’s first ionization coefficient is the average number of ionizing collisions made by an electron per centimeter travel
in the direction of the field.

5. What is a Townsend’s secondary ionization coefficient?

The Townsend’s secondary ionization coefficient is defined as the net number of secondary electrons produced per
incident, positive ion, photon, excited particle or meta- stable particle.

6. What are electro negative gases?

The gases which are highest breakdown strength due to attachment of free electrons to neutral atoms or molecules to form
negative ions, thus removing free electrons that would otherwise led to breakdown is called as electro negative gases.

7. Define an attachment coefficient.

An attachment co-efficient is defined as the number of attaching collusions made by one electron drifting one centimeter
in the direction of the field.

8. What is meant by time lag?

The time difference between the application of a voltage sufficient to cause breakdown and the occurrence of breakdown
itself is called as time lag.
9. Mention some of the applications of liquiddielectrics.
They are used as impregnants in high voltage cables and capacitors, and for filling up of transformers, circuit breakers. They
are also used as heat transfer agents in transformers and as arc quenching media in circuit breakers.

10. Name some examples of liquid dielectrics.

Petroleum oils, Synthetic hydrocarbons, halogenated hydrocarbons, silicone oils and fluorinated hydrocarbons.

11. What are pure liquids? Giveexamples.

They are chemically pure and do not contain any other impurity even in traces of 1in 109 and are structurally
simple. Examples are n-hexane, n-heptane and other paraffin hydrocarbons.

12. What are the different types of solid insulatingmaterials?

Organic materials: paper, wood and rubber, Inorganic materials: Mica, glass and porcelain Synthetic polymers:
Persplex, PVC, epoxy resins.

13. State the properties of gooddielectrics

Low dielectric loss, high mechanical strength, should be free from gaseous inclusions and moisture and be resistant to
thermal and chemical deterioration.

5
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
14. State and explain Paschen’s law.
The Townsends breakdown criterion for gases is given by γ(eαd-1) = Where α, γ are the Townsends co- efficient and are
functions of (E/p).

15. What do you mean by “Intrinsic strength‟of a solid dielectric?

When voltage is applied for a short time of the order of 10-8 , the electric strength of the solid material increases rapidly to
an upper limit. This is called Intrinsic strength.

16. Define treeing and tracking.

Treeing is the formation of a continuous conducting path across the surface of the insulation mainly due to surface erosion
under voltage application. Insulation failure occurs when carbonized tracks bridge the distance between the electrodes. This
phenomenon is called tracking.

17. What is meant by corona discharges?

In non-uniform fields, the increase in voltage cause breakdown in the gas at points with highest electric field
intensity(sharp points), or where the electrodes are curved or on transmission lines. This form of discharge is called as
corona discharge.

18. What are the properties required for a gaseous dielectric for HV application?
Generally , the preferred properties of a gaseous dielectric for high voltage applications are:
 High dielectric strength
 Thermal stability and chemical inactivity towards materials ofconstruction
 Non-flammable and physiological inertness, and environmentallynon-hazardous
 Low temperature of condensation
 Arc extinguishing ability
 Good heat transfer
 Commercially available at moderate cost.

19. What are commercial liquid dielectrics and how are they different from pure liquid dielectrics?
 Pure liquids are those which are chemically pure and do not contain any other impurity even in traces of 1 in 109,
and are structurally simple.
Examples of such simple, pure liquids are n-hexane , n-heptane and other paraffin hydrocarbons.
 Commercial liquids which are insulating liquids like oils which are not chemically pure.
 Normally consist of mixtures of complex organic molecules which cannot be easily specified or reproduced in a
series of experiments.

20. What is meant by “Penning effect”?

Penning Effect is a form of chemi-ionization, an ionization process involving reactions between neutral atoms or
molecules. The process is named after the Dutch physicist Frans Michel Penning who first reported it in 1927. The
Penning effect is put to practical use in applications such as gas-discharge neon lamps and fluorescent lamps, where the lamp is
filled with a Penning mixture to improve the electrical characteristics of the lamps.

21. What are the factors which affect the breakdown in gaseous dielectrics?
If the applied voltage are large , the current flowing through the insulation increases very sharply and an electrical
breakdown occurs. The factors which affect the breakdown in gaseous dielectrics are,

6
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
 Low dielectric strength
 Thermal and chemical instability
 Flammability and hazardous
 Bad heat transfer
PART –B & C
1. What are the Electro negative gases? Why is the break down strength higher in these gases compared to that
in other gases? Explain the streamer theory of break down in air at atmospheric pressure.
2. Discuss the various mechanisms of vacuum break down.
3. Explain the theories that explain break down in commercial liquid dielectrics.
4. Explain the Townsends criterion for a spark.
5. What do you understand by intrinsic strength of solid dielectrics? Explain different mechanisms by which breakdown occurs
in solid dielectrics in practice.
6. State the criteria for sparking potential and hence obtain the relation between sparking potential and (pd) values
(Paschen‟s Law). Discuss on the nature of variations of sparking potential with (pd) values.
7. A solid dielectric specimen of dielectric constant of 4.0 shown in the figure has an internal void of thickness 1 mm.
The specimen is 1 cm thick and is subjected to a voltage of 80 kV (rms). If the void is filled with air and if the
breakdown strength of air can be taken as 30 k V (peak)/cm, find the voltage at which an internal
discharge canoccur.

8. Explain composite dielectrics and how the breakdown occurs in it?

9. Explain Thermal break down in solid dielectrics? Derive an expression for critical thermal breakdown
voltage(Vc) and critical electric field (Ec) for the same. State clearly the assumption made.
10. A certain dielectric can be considered to be represented by the equivalent circuit shown in figure. What is the
maximum voltage that can be applied across the dielectric, if partial discharges in air to be avoided? State any
assumptions made.

UNIT III GENERATION OF HIGH VOLTAGES AND HIGH CURRENTS

PART A
1.What does the selection of BIL level for lines depend?
Atmospheric conditions, lightning activity, insulation, pollution and acceptable outage of the line.
2. What are the disadvantages of half wave rectifier circuit?

7
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
 Low dc output power and lower efficiency.
 Higher ripple voltage & ripple current.
 Higher ripple factor.
 Low transformer utilization factor.
 The input supply current waveform has a dc component which can result in dc saturation of
the transformer core.
3. What are the classifications of high voltages?
High dc, high ac of power frequency, high ac of high frequency and impulse voltages.
4. What is regulation?
The change of average voltage across the load from the no load theoretical value expressed as a
percentage of no load is called regulation.
5.What is a tesla coil?
The high frequency resonant transformer is called as a tesla coil.
6.What are the uses of high frequency high voltages?
They are required for rectifier dc power supplies. Also it is used for testing electrical apparatus for
switching surges.
7.Mention the advantages of high frequency transformers.
Saving in cost and size, pure sine wave output, uniform distribution of voltage across the winding coils
due to subdivision of coil stack into number of units.
8. Mention the specifications of standard impulse wave.
By defining the rise of front time and tail time 1.2/50µs, 1000 KV (standard value), fall time to 50%
peak value of50𝜇s and a peak value of 1000 kV.
9. Mention the circuits to produce impulse waves.
In the laboratory with a combination of a series R-L-C circuit under over damped conditions or by the
combination of 2 R-C circuits.
10. Name the multi test sets used for high voltage testing.
Ac testing transformers, dc units, impulse voltage units.
11. What is transient voltage?
It is an oscillatory wave or a damped oscillatory wave of frequency ranging for few Hundred hertz to
few kilohertz.
12. What are the components of a multistage impulse generator?
Dc charging unit, charging resistors, generator capacitors and spark gaps, wave shaping resistors and
capacitors, triggering system, voltage dividers and gas insulated impulse generators.
13. Define the duration of the wave.
It is defined as the total time of the wave during which the current is at least 10% of its peak value.
14. How are impulse currents of large value produced?
A bank of capacitors connected in parallel are charged to a specified value and are discharged through
a series R-Lcircuit.
15. Explain Deltatron circuit.
A combination of Cockcroft Walton type voltage multiplier with cascaded transformer dc rectifier is
developed for very high voltages but limited output currents having high stability, small ripple factor
and fast regulation. This type of circuit is called deltatron circuit.

8
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
16. Mention the advantage of trigatron gap?
It requires much smaller voltage for operation compared to the three-electrode gap.
17. What are the components of a trigatron gap?
It consists of a high voltage spherical electrode of suitable size, an earthed main electrode of spherical
shape and a trigger electrode through the main electrode.
18. What are drawbacks of single stage circuit for the generation of very high impulse voltage?
For higher voltage requirements a single unit construction becomes difficult and costly due to
insulation problems. Erection and transportation becomes difficult.

19. What is a cascaded transformer?

Input of the first transformer unit is supplied from a motor generator or from a voltage regulator. The
primary winding is supplied from a source. The high voltage winding of the first unit is connected to
the tank of the second unit. The rating of the excitation winding is almost identical with that of primary
winding voltage.
20. Give some merits of vande Graff generator.
 Very high DC voltage can be generated easily.
 Ripple free output.
 Precision and flexibility of control.
 Stability of voltage can be achieved with suitable stabilizing devices.

21. Give any twomethods of switching surge generation in laboratory.

 By changing the tail time constants of impulse generator.
 By connecting primary and secondary windings of power transformer in series.

22. Define the front and tail times of impulse wave.

Rise or Front time: It is the time required for the response to raise from 10 to 90% or 0 to 100% of
the final value at the very first instance. Rise time for standard impulse wave of 1.2/50 μ s,1000 kV =
1.2 μ s.
Fall or Tail time : Fall time is the time to reach 50% peak value of 50 μ s. Fall time for standard
impulse wave of 1.2/50 μ s,1000 kV = 50% peak value of 50μ s.
23. Mention the necessity of generating high dc voltage.
The generating high dc voltage is necessary for,
 Research work in applied physics
 Charging of impulse generators
 Insulation tests on cables and capacitors
 Rectifiers are used to get HVDC up to 100 kV and 100mA

24. What are the advantages of series resonant circuit?

 It gives an output of pure sine wave.
 Power requirements are less.(5 to 10% of total KVA required)
 No high power arcing and heavy current surges occur if the test object fails , a resonance
ceases at the failure of the test object.
 Cascading is also possible for very high voltages.
 Simple and compact test arrangement.
 No repeated flashovers occur, in case of partial failure of test objects.

9
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
25. How is the circuit inductance controlled and minimized in the impulse current generator?
If the series resistance R\ is increased, the wave front oscillations are damped, but the peak value of
the voltage is also reduced. Thereby circuit inductance can be controlled and minimized in the impulse
current generator.
PART B & C
1. Why is Cock croft –Walton circuit preferred for voltage multiplier circuits? Explain its
working with a schematic diagram when it is unloaded and loaded. Derive an expression for total
voltage drop and total ripple voltage of n-stage voltage multiplier circuit and hence deduce the
condition for optimum number of stages.
2. i) Mention the necessity of generating high DCvoltages.
ii) Describe with a neat sketch the working of a Van De Graff generator. What are the factors
that limit the maximum voltage obtained?
3. What is the principle of operation of a resonant transformer? How is it advantages over the
cascade- connected transformer? Explain the basic principle of operation of an electrostatic
generator.
4. How are damped high frequency oscillation obtained from a Tesla coil? Explain.
5. Give the Marx circuit arrangement for multistage impulse generators. How is the basic
arrangement modified to accommodate the wave time control resistances?
6. Explain the different methods of producing switching impulses in test laboratories. Draw the
typical impulse current generator circuit and explain its operation and applications.
6. A Cockcroft-Walton type voltage multiplier has eight stages with capacitances, all equal to
0.05 pF. The supply transformer secondary voltage is 125 kV at a frequency of 150 Hz. If the
load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the
optimum number of stages for minimum regulation or voltage drop.
7. Explain tripping and control of impulse generators with Trigatron gap arrangements. How
are the wavefront and wavetail time controlled in impulse generator circuits?
8. What is a cascaded transformer? Explain why cascading is done? Describe with neat
diagram, a 3-stage cascaded transformer.
9. A six stage impulse generator designed to generate the standard waveform (1.2/50 s) has a
per stage capacitance of 0.06 𝜇F to be used to test transformers with an equivalent winding to
earth capacitance of 1nF. A peak output voltage of 550kV is required for testing the
transformer. The wavefront time is to be defined based on 30% and 90% values. With the aid of
appropriate calculations select the values of the resistive elements in the circuit to produce the
required waveform. State any assumptions made.

UNIT IV MEASUREMENT OF HIGH VOLTAGES AND HIGHCURRENTS

PART-A
1. Mention the techniques used in impulse current measurements. Hall generators, Faraday
generators and current transformers.
2.Mention the problems associated with bifilar strip design.
The shunt suffers from stray inductance associated with resistance element and its potential leads are
linked to a small part of the magnetic flux generated by the current that is measured.
3.Mention the different ways in which the stray effect is reduced in resistance shunt? Bifilar flat
strip design, Co-axial tube or park’s shunt design and Co-axial squirrel cage design.

10
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC

4.State the advantages of Sphere gaps?

They are used for voltage measurements. They are suitable for all types of waveforms from d.c to
impulse voltages of short times. They are used for radio frequency a.c voltage peak measurements upto
1 MHz.
5. State the advantages of magnetic potential transformers.
They are simple in construction and designed for any voltage. For very high voltages cascading of the
transformers are possible.
6. How is an electric field is measured?
It is measured by introducing a small fixed capacitance probe into the field area and measuring the
induced charge on it.
7.Mention the devices used to measure the d.c electric field strength.
Variable capacitor probe and a vibrating plate capacitor.
8. Give the advantages of generating voltmeters
No source loading by the meter. No direct connection to high voltage electrode. Scale is linear and
extension of range is easy.
9. How is an electric field is measured?
It is measured by introducing a small fixed capacitance probe into the field area and measuring the
induced charge on it.
10. Explainthe porosity test on insulators.
The insulator is broken and immersed in a 0.5 % alcohol solution under a pressure of 13800 kN/sq.m
for 24 hours. The broken insulator is taken out and further broken. It should not show any sign of
impregnation.
11. Why is the cable meant for a.c system to be tested with dc supply?
Cables are tested for power frequency ac and dc voltages. During manufacture the entire cable is
passed through a higher voltage test and the rated voltage to check the continuity of cable. High
voltage dc of 1.8 times the rated dc voltage of negative polarity for 30 minutes is applied and cable is
set to have no failure.
12. What is the effect of nearbyearthed objects on the measurements using sphere gaps?
The spark over voltage is reduced due to the presence of nearby earthed objects.
Voltage reduction, ∆V=mlog ( B) +C
D
Where, B – diameter of earthed enclosing cylinder, D – diameter of the spheres C – gap distance
between spheres, m,c – constants
13. Define CVT.
CVT meant for capacitive voltage transformer. It is used for measurement, relaying applications and
sometimes for carrier communications.
14. Explain the basic principleof Hall generator.
It is based on the principle of hall effect. Whenever electric current flows through a metal plate
located in a magnetic field perpendicular to it, Lorentz forces will deflect the electrons in the metal

11
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
structure in a direction normal to the direction of both currents and magnetic field. The charge
displacement generates an emf. This is called Hall voltage. VH α BI/d
15. List some advantages of Faraday generator.
 There is no electric connection between the source and the device.
 No thermal problems even for large currents of several kilo amperes.
 There is no insulation problem, as the signal transmission is through an optical system.
16. Give the advantages of electrostatic voltmeter.
The electrostatic voltmeter is (i)compact and smaller in size (ii) it has high input impedance, therefore
no need to have meter protection additionally (iii) the range of the meter can be easily changed by
changing gap separation.
17. What is the effect of dust particles on the measurement using sphere gaps?
Field configuration may change will leads to incorrect measurement. Therefore the surface of the
sphere should be free from dust, grease, or any other coating.
18. List out the limitations of generating voltmeters.
 Need calibration.
 Careful construction is needed.
 Any disturbance due to position and mounting of the electrodes make the calibration invalid.

20. Give the procedure for dc and ac peak voltage measurement using sphere gap.
A uniform field spark gap will always have a spark over voltage within a known tolerance under
constant atmospheric conditions. Hence a spark gap can be used for measurement of the peak value of
the voltage, if the gap distance is known. A spark over voltage of 30 kV (peak) at 1 cm spacing in air
at 2O0C and 760 torr pressure occurs for a sphere gap or any uniform field gap. But experience has
shown that these measurements are reliable only for certain gap configurations. Normally, only sphere
gaps are used for voltage measurements.
21. What are the different types of resistive shunts used for impulse current measurements?
(a) Bifilar flat strip design,(b) coaxial tube or Park's shunt design, and(c) coaxial squirrel cage design
22. What are the drawbacks of series resistance micro ammeter technique in HVAC
measurements?
The drawbacks of this technique are (i)power dissipation and source loading, (ii) temperature effects
and long time stability, (iii)voltage dependence of resistive elements, and (iv) sensitivity to
mechanical stresses.
23. How the stray effect of capacitance potential divider is minimized for impulse
measurements?
The effect to residual and lead inductances becomes pronounced when fast rising impulses of less than
one microsecond are to be measured. The residual inductances damp and slow down the fast rising
pulses. Secondly, the layout of the test objects, the impulse generator, and the ground leads also
require special attention to minimize recording errors.
24. What is the principle behind the operation of generating voltmeter?
A generating voltmeter is a variable capacitor electrostatic voltage generator which generates current
proportional to the applied external voltage. The device is driven by an external synchronous or
constant speed motor and does not absorb power or energy from the voltage measuring source.
25. What are the differences between a high voltage testing transformer and a power
transformer?

12
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
A high voltage testing transformer (a)gives an output of pure sine wave, (b) power requirements are
less (5 to 10% of total kVA required),(c) no high-power arcing and heavy current surges occur if the
test object fails, as resonance ceases at the failure of the test object,(d) cascading is also possible for
very high voltages,(e) simple and compact test arrangement, and(f) no repeated flashovers occur in
case of partial failures of the test object and insulation recovery. It can be shown that the supply
source takes Q number of cycles at least to charge the test specimen to the full voltage.
Power transformers are generally used in transmission network for stepping up or down the voltage
level. It operates mainly during high or peak loads and has maximum efficiency at or near full load.
26. What are the advantages of generating voltmeter?
i) No source loading by the meter,
ii)No direct connection to the high voltage electrode,
iii)Scale is linear and extension of range is easy, and
iv) A very convenient instrument for electrostatic devices such as Van de Graaff
generator andparticle accelerators.
PART B & C
1. Explain with neat diagram the principle of operation of an electrostatic voltmeter. Discuss its
advantages and limitations for high voltage measurements.
2. Explain the different methods of high d.c, a.c and impulse current measurement with their
relative merits demerits.
3.(i) Give the schematic arrangement of an impulse potential divider with an oscilloscope
connected for measuring impulse voltages. Explain the arrangement used to minimize the errors.
(ii) What are the requirements of a digital storage oscilloscope for impulse and high frequency
measurement in HV test circuits?
4. A Rogowski coil is to be designed to measure impulse currents of 10 kA having a rate of
change of current of 1010A/s .The current is read by a VTVM as a potential drop across the
integrating circuit connected to the secondary. Estimate the values of mutual inductance,
resistance, and capacitance to be connected, if the meter reading is to be 10 V for full-scale
deflection.
5. i) Enumerate digital peak voltmeter.
ii) What is CVT? Explain how CVT can be used for high voltage ac measurement.
6. Describe the construction, principle of operation of a Generating voltmeter and give its
applications and limitations.
7. Discuss and compare the performance of resistance, capacitance and mixed R-C potential
dividers for measurement of impulse voltages. Draw the simplified equivalent circuit of
resistance potential divider and discuss its step response.
8. Describe the construction of uniform field spark gap and discuss its advantages and
disadvantages for high voltage measurements. Explain the procedure for peak value
measurement of high voltage DC,AC and impulse voltage using standard sphere gap. Explain
the parameters and factors that influence the sphere gap measurement.
9. Explain in detail various techniques for the measurement of high DC voltages.
10. With neat sketch, explain in detail the various methods used to measure the RMS and peak
values of high AC voltages.

13
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
UNIT V HIGH VOLTAGE TESTING & INSULATIONCOORDINATION
PART - A
1. What is a surge diverter?
It is a non-linear resistor in series with a spark gap kept at line terminals in the substations.
2. Define creeping distance.
It is the shortest distance on the contour of the external surface of the insulator unit.
3. What is the importance of radio interference voltage measurements for extra high voltage
power apparatus?
In the power apparatus it produces unwanted electrical signals in radio and high frequency ranges. It
is important to see that the noise generated should be reduced. For this purpose this measurement is
important.
4. Define withstand voltage.
The voltage which has to be applied to a test object under specified conditions in a withstand test is
called the withstand voltage.
5. Define an isolator.
It is a disconnector or a mechanical switching device, which provides in the open position an isolating
distance in accordance with special requirements.
6. Define partial discharge.
An electrical discharge that only partially bridges the dielectric between the conductors. Examples are
surface discharge, internal discharge
7. Define a circuit breaker.
It is a switch, which automatically interrupts the circuit when a critical current ovrvoltage rating is
exceeded.
8. What is the function of surge arrester?
They are capable of discharging 10 to 20 KA of long duration surges and 100 to250 KA of short
duration surge currents.
9. State the consequences of RIV.
When the noise meter measurements are stated the information regarding the specification of meters
used in the band pass characteristics and the open circuit the detector characteristics has to be
mentioned.
10. What do you mean by radio interference?
The power apparatus produces unwanted signals in the radio and high frequency ranges.These are
called radio interference.
11. Mention the characteristics of the spray used in wet flashover test.
The characteristics of the spray are
Precipitation rate : 3 ± 10% (mm/min)
Direction : 45° to the vertical
Conductivity of water : 100 micro Siemens ± 10%
Water temperature : ambient ±15°C

12. How is impulse with-stand voltage test conducted?

14
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
This test is done by applying standard impulse voltage of specified value under dry conditions with
both positive and negative polarities of the wave. If five consecutive waves do not cause a flashover
or puncture, the insulator is deemed to have passed the test. If two applications cause flashover, the
object is deemed to have failed. If there is only one failure, additional ten applications of the voltage
wave are made. If the test object has withstood the subsequent applications, it is said to have passed
the test.
13. Define 50% flashover.
It is the voltage, which has the 50 % flashover when applied to test object.
14. Define 100 % flash over.
The voltage that causes a flashover at each of its application under specified conditions when applied to
test objects as specified.
15. State two standard tests to be conducted on HVTransformers.
Induced over voltage test and partial discharge test
16. List out various tests to be carried out on insulator and give a brief account of each test.
High voltage test include power frequency test and impulse tests. These tests are carried out on all
insulators. (i) 50% dry impulse flashover test (ii) impulse withstand test (iii) dry flashover & dry one
minute test (iv) wet flashover test (v) temperature cycle test(vi) electromechanical test (vii) porosity
test(ix)puncture test (x) mechanical routine test.
17. What are significance of power factor test?
High voltage schering bridge is used to perform dielectric power factor test on the cable sample. The
power factor is measured for different values of voltages eg 0.5,1,1.5,2 times of rated operating
voltages. The maximum value of power factor at normal working voltage does not exceed a specified
voltage at a series of temperatures ranging from 15 to 650C .
18. Find and locate the fault during impulse testing of transformer.
Fault can be located by any one of the following methods:
General observation, voltage oscillogram method, neutral current method, and transformer surge current
methods.
19. Define 100 % flash over.
The voltage that causes a flashover at each of its application under specified conditions when applied to
test objects as specified.
20. What is the type and routine test?
The type test is conducted on the sample to test the quality of the material with which the component is
made. Routine test is conducted on the equipment or component periodically to check the deterioration
in the quality during operation.
21. Define Disruptive discharge voltage.
This is defined as the voltage which produces the loss of dielectric strength of an insulation. It is that
voltage at which the electrical stress in the insulation causes a failure, which includes the collapse of
voltage and passage of current. In solids, this causes a permanent loss of strength, and in liquids or
gases only temporary loss may be caused. When a discharge takes place between two electrodes in a
gas or a liquid or over a solid surface in air, it is called flashover. If the discharge occurs through a
solid insulation it is called puncture.
22. Distinguish between flashover and puncture.

15
 TAGORE INSTITUTE OF ENGINEERING AND TECHNOLOGY
Deviyakurichi-636112, Attur (TK), Salem (DT). Website: www.tagoreiet.ac.in
Approved by AICTE, New Delhi and Affiliated to Anna University, Chennai

Accredited by NAAC
When a discharge takes place between two electrodes in a gas or a liquid or over a solid surface in air, it
is called flashover. If the discharge occurs through a solid insulation it is called puncture.
23. Define safety margin as applied to insulation coordination.
The Safety margin is defined by selecting the risk of failure, the statistical safety factor and by firing
the withstand level of any equipment or apparatus corresponding to 90% or 95% of the withstand
voltage.
24. What is BIL?
It is defined as the minimum insulation impulse withstands voltage of any power equipment or
apparatus. The BIL of a power system is usually chosen as 25% to 30% more than the protective level
Offered by the protective devices.

25. Calculate the correction factor for atmospheric conditions, if the laboratory temperature is
37oC, the atmospheric pressure is 750 mmHg and the wet bulb temperature is 27oC.
Air density correction factor, d= 0.296b for 27oC, Atmospheric pressure in mbar, b = 999.91mbar,
T=37oC then d= 0.954
26. What are the tests need to be conducted on the power transformer.
i) induced overvoltage test
ii) Partial discharge test
iii) Impulse voltage test
PART –B & C
1. What are the different power frequency tests done on insulators? Mention the procedure for
testing.
2. What are the significance of power factor tests and partial discharge tests on bushings? How
are they conducted in testing laboratory?
3. Explain the method of impulse testing of high voltage transformers. What is the procedure
adopted for locating the failure.
4. Why is synthetic testing advantages over the other testing methods for short circuit tests? Give
the layout for synthetic testing.
5. Explain the importance of RIV measurements for EHV power apparatus. Explain, with a neat
schematic diagram, one method of measuring RIV of Transmission line hardware.
6. Explain the various tests conducted in high voltage cables.
7. Describe the various tests to be carried out on a circuit breaker.
8. Explain the different aspects of insulation design and insulation co-ordination adopted for
EHV systems.

16