EBARA Submersible Wastewater Pumps DMLEU

Contents
Project: Model: Chk’d: Date:
Model
80DMLEU62.2 100DMLEU63.7 150DMLEU65.5
80DMLEU63.7 100DMLEU65.5 150DMLEU67.5
80DMLEU65.5 100DMLEU67.5 150DMLEU611
80DMLEU67.5 100DMLEU611 150DMLEU615
80DMLEU611 100DMLEU615 150DMLEU622
80DMLEU615 100DMLEU622
80DMLEU622

Section Page

Specifications 2-138
Selection Chart 2-141
Performance Curves 2-142
Dimensions 2-146
Sectional View 2-150
QDC Information 2-278
Motor Data 2-153
motor electrical specifications
cable data
wiring diagrams
motor electrical data

EBARA Fluid Handling

www.pumpsebara.com 2-136
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Model Designation
Project: Model: Chk’d: Date:

80 DMLE U 6 1.5 4

DISCHARGE SIZE – mm
80mm – 3"
100mm – 4"
150mm – 6"

MODEL TYPE
DMLE– submersible sewage pump

GEOGRAPHIC DESIGNATION
U – U.S.A. market

HERTZ
6 - 60

RATED KW
2.2 – 3HP 11 – 15HP
3.7 – 5HP 15 – 20HP
5.5 – 71/2HP 22 – 30HP
7.5 – 10HP

PHASE
none – three phase

VOLTAGE
2 - 208/230
4 - 460

EBARA Fluid Handling

www.pumpsebara.com 2-137
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Specifications
Project: Model: Chk’d: Date:
Model DMLEU
Specifications

Standard Optional

Size 3, 4, 6 inch

Range of HP 3 to 30HP

Range of Performance Capacity: 55 to 1345 GPM

Head: 12 to136 feet
Limitation
Maximum Water Temperature 104°F (40°C)
Synchronous Speed 1800 RPM
Materials
Casing Cast Iron
Impeller Cast Iron
Shaft 403 Stainless Steel
Motor Frame Cast Iron
Fastener 304 Stainless Steel
Mechanical Seal Double Mechanical Seal
Material – Upper Side Carbon/Ceramic
Material – Lower Side Silicon Carbide/Silicon Carbide
Impeller Type Non-clog single channel enclosed
Bearing Pre-lubricated Ball Bearing
Motor Air-filled, dry submersible, Class F Insulation
Three Phase 208/230 or 460V
Service Factor 1.15
Motor Protection Built-in Auto cut (3HP model)
Thermal Detector – Klixons
Mechanical seal leak detector – internal oil probe
Accessories Submersible cable 33 ft. 66 ft.
QDC System

EBARA Fluid Handling

www.pumpsebara.com 2-138
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Specifications
Project: Model: Chk’d: Date:
A. General:
Provide submersible sewage pumps suitable for continuous duty operation underwater without loss of watertight
integrity to a depth of 65 feet. If mounted on a guide rail system, design shall be such that the pump will be auto-
matically connected to the discharge piping when lowered into place on the discharge connection. The pump shall
be easily removable for inspection or service, requiring no bolts, nuts, or other fasteners to be disconnected, or the
need for personnel to enter the wet well. The motor and pump shall be designed, manufactured, and assembled by
the same manufacturer.

B. Manufacturer:
EBARA International Corporation

C. Pump Characteristics:
Pumps shall conform to the following requirements:

Number of units
Design flow (gpm)
Design TDH (ft)
Minimum shut off head (ft)
RPM 1800
Maximum HP
Minimum efficiency at design (%)
Minimum power factor at design (%)
Voltage/HZ 208/230V, 460V / 60
Phase

D. Pump Construction:
All major parts of the pumping unit(s) including casing, impeller, motor frame and discharge elbow shall be manufactured
from gray cast iron, ASTM A-48 Class 30. Castings shall have smooth surfaces devoid of blow holes or other casting
irregularities. Casing design shall be centerline discharge with a large radius on the cut water to prevent clogging.
Units shall be furnished with a discharge elbow and 125 lb. flat face ANSI flange. All exposed bolts and nuts shall
be 304 stainless steel. All mating surfaces of major components shall be machined and fitted with NBR O-rings
where watertight sealing is required. Machining and fitting shall be such that sealing is accomplished by automatic
compression of O-rings in two planes and O-ring contact is made on four surfaces without the requirement of specific
torque limits. Internal and external surfaces are prepared to SPPC-VISI-SP-3-63 then coated with a zinc-chromate
primer. The external surfaces are then coated with a Modified epoxy resin (Product name: Metal Grip Black_Mod)
by air spray.

Impeller shall be single vane enclosed design. The impeller design shall include back pump out vanes to reduce the
pressure and entry of foreign materials into the mechanical seal area. The inlet edge of the impeller vanes shall be
angled toward the impeller periphery so as to facilitate the release of objects that might otherwise clog the pump.
Impellers shall be direct connected to the motor shaft with a slip fit, key driven, and secured with an impeller bolt.
The unit shall include a replaceable casing wear ring at the pump suction to maintain working clearances and
hydraulic efficiencies.

Double mechanical seals operating in an oil bath shall be provided on all units. The oil filled seal chamber shall be
designed to prevent over-filling and include an anti-vortexing vane to insure proper lubrication of both seal faces.
Lower face materials shall be silicon carbide vs. silicon carbide, upper faces carbon vs. ceramic, NBR elastomers,
and 304SS hardware. Seal system shall not rely on pumping medium for lubrication.

EBARA Fluid Handling

www.pumpsebara.com 2-139
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Specifications
Project: Model: Chk’d: Date:
E. Motor Construction:
The pump motor shall be an air filled induction type with a squirrel cage rotor, shell type design, built to NEMA
MG-1, Design B specifications. Stator windings shall be copper, insulated with moisture resistant Class F insulation,
rated for 311°F. The stator shall be dipped and baked in Class F varnish and heat shrunk fitted into the stator housing.
Rotor bars and short circuit rings shall be manufactured of cast aluminum. Motor shaft shall be one piece AISI403
material, rotating on two permanently lubricated ball bearings designed for a minimum B-10 life of 60,000 hours.
Motor service factor shall be 1.15 and capable of up to 20 starts per hour. The motor shall be designed for continuous
duty pumping at a maximum sump temperature of 104°F. Voltage and frequency tolerances shall be a maximum 10 / 5%
respectively. For 3 HP units, motor protection shall be provided by an auto-cut device located directly over the windings
to provide protection from single phasing, low voltage, phase imbalance, locked rotor, and no load or run dry conditions.
Motor over temperature protection shall be provided by miniature thermal protectors embedded in the windings. An
electrical probe shall be provided in the oil chamber for detecting the presence of water. The probe shall be mounted
internally to the motor housing. A solid state device mounted in the pump control panel or in a separate enclosure
shall send a low voltage, low amperage signal to the probe. If water enters the oil chamber, the probe shall close an
electrical circuit and energize a warning device. Motor shall be non-overloading over the entire performance curve
and be able to operate at full load intermittently while unsubmerged without damage to the unit.

Power cable jacket shall be manufactured of an oil resistant chloroprene rubber material, designed for submerged
applications. Cable shall be watertight to a depth of a least 65'. Cable entry shall be composed of a one piece,
vulcanized, three way mechanical sealing system with a thick molded shoulder with increasing cable diameters to
resist fatigue from bending forces. The molded shoulder, acts as the primary and secondary sealing points. This
system shall also prevent leakage into the motor housing due to capillary action through the insulation if the cable is
damaged or cut. A metallic plate shall be utilized to clamp the entry system to the motor housing.

F. Guide Rail system:

Design shall include two (2) 304SS schedule 40 guide rails sized to mount directly to the quick discharge connector,
QDC, at the floor of the wet well and to a guide rail bracket at the top of the wetwell below the hatch opening, (refer
to project drawings). Intermediate guide brackets are recommended for rail lengths over 15 feet.

Guide rails are not part of the pump package and shall be supplied by others.

The QDC shall be manufactured of cast iron, ASTM A48 Class 30. It shall be designed to adequately support the
guide rails, discharge piping, and pumping unit under both static and dynamic loading conditions with support legs
that are suitable for anchoring it to the wetwell floor. The face of the inlet QDC flange shall be perpendicular to the
floor of the wetwell. The discharge flange of the QDC shall conform to ANSI B16.1 Class 125.

The pump design shall include an integral self-aligning sliding bracket. Sealing of the pumping unit to the QDC shall
be accomplished by a single, linear, downward motion of the pump. The entire weight of the pump unit shall be guided
to and wedged tightly against the inlet flange of the QDC, making metal to metal contact with the pump discharge
forming a seal without the use of bolts, gaskets or O-rings.

A stainless steel lifting chain of adequate length for removing and installing the pump unit is recommended. The chain
shall have a round link with a 2-1/4'' inside diameter every two feet. This link will allow for a sliding pinch bar through
the link to pick the chain, more than once if necessary, at multiple intervals during pump removal and installation.

EBARA Fluid Handling

www.pumpsebara.com 2-140
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Selection Chart
Project: Model: Chk’d: Date:
Model DMLEU
Selection chart

m ft. 60 Hz (Synchronus Speed: 1800 RPM)

50
40 140
120 80DMLE622
30 100 80DMLE615
90 100DMLE622
80 80DMLE611
100DM
20 70 80DMLE67.5 LE615
60

15
0D
80DMLE65.5 100DMLE611
Total Head

50

ML
E6
15

22
0D
100
40 DM

M
LE6

LE
80DMLE63.7 7.5

61
10

5
100D

15
9 30 MLE

0D
65.5

ML
8

E6
150
7

11
DM
6 20

LE6
150
80DMLE62.2 100DMLE63.7

7.5
DM
5

LE6
5.5
4
3 10

2
50 100 200 300 400 500 600 800 1000 1400 2000 USGPM

0.1 0.2 0.3 0.4 0.5 1.0 2 3 4 5 6 7 8 9 10 m 3/min.

Capacity

EBARA Fluid Handling

www.pumpsebara.com 2-141
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Performance Curves
Project: GPM: TDH: EFF: HP: Chk’d: Date:

80DMLE62.2 (3HP) Synchronous Speed: 1800 RPM 3 inch Discharge

80CML62.2 (3 HP) Synchronous Speed: 1800 RPM 3 Inch Discharge
100 50
Curve No: F8-0132447
90 Solid Dia 3"
LM80

80 40
158 mm Impeller

70
Total Head (Ft)

EFFICIENCY
Efficiency (%)

60 30

50

40 20

Brake Horsepower (BHP)

30

20 10
BHP 3
10 2
1
0 0 0
0 50 100 150 200 250 300 350 400 450 500

Capacity USGPM

80, 100DMLE63.7 (5HP) Synchronous Speed: 1800 RPM 3, 4 inch Discharge

80,100CML63.7 (5 HP) Synchronous Speed: 1800 RPM 3, 4 Inch Discharge
100 70
Curve No: F8-0132448-9
90 Solid Dia 3"
LM80
60
183 mm Impeller
80

70 50
EFFICIENCY
Total Head (Ft)
Efficiency (%)

60 80DMLE63.7
40

50

30
40 100DMLE63.7
Brake Horsepower (BHP)

30 20

20 BHP 5
4
10
3
10
2
1
0 0 0
0 100 200 300 400 500 600 700

Capacity USGPM

EBARA Fluid Handling

www.pumpsebara.com 2-142
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Performance Curves
Project: GPM: TDH: EFF: HP: Chk’d: Date:

80, 100, 150DMLE65.5 (7.5HP) Synchronous Speed: 1800 RPM 3, 4, 6 inch Discharge
80,100, 150CML65.5 (7-1/2 HP) Synchronous Speed: 1800 RPM 3, 4, 6 Inch Discharge
100 80
Curve No: F8-0132450-1-2
90 183 mm Impeller Solid Dia 3"
70 LL1000

80
60
70
80DMLE65.5 EFFICIENCY
Total Head (Ft)

50
Efficiency (%)

60

50 40
100DMLE65.5

40

Brake Horsepower (BHP)

30
150DMLE65.5
30 BHP 7.5
20
20 5.0

10
10 2.5

0 0 0.0
0 100 200 300 400 500 600 700 800 900

Capacity USGPM

80, 100, 150DMLE67.5 (10HP) Synchronous Speed: 1800 RPM 3, 4, 6 inch Discharge
3, 4, 6 Inch Discharge
100 90
Curve No: F8-0132453-4-5
90 213 mm Impeller Solid Dia 3"
80
LL100

80
70
80DMLE67.5
70
60
EFFICIENCY
Total Head (Ft)
Efficiency (%)

60
50
50
100DMLE67.5
40
40 10
Brake Horsepower (BHP)

30 8
30 150DMLE67.5
BHP 6
20
20
4
10 10
2

0 0 0
0 100 200 300 400 500 600 700 800 900 1000

Capacity USGPM

EBARA Fluid Handling

www.pumpsebara.com 2-143
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Performance Curves
Project: GPM: TDH: EFF: HP: Chk’d: Date:

80, 100, 150DMLE611 (15HP) Synchronous Speed: 1800 RPM 3, 4, 6 inch Discharge
80,100,150CML611 (15 HP) Synchronous Speed: 1800 RPM 3, 4, 6 Inch Discharge
100 110
Curve No: F8-0132456-7-8
90 100 240 mm Impeller Solid Dia 3"
LL100
90
80 80DMLE6711

80
70
70
Total Head (Ft)

EFFICIENCY
Efficiency (%)

60
100DMLE611
60
50
50
40 150DMLE611

Brake Horsepower (BHP)

40
30
30 BHP
15
20
20 10

10 10 5

0 0 0
0 200 400 600 800 1000 1200

Capacity USGPM

80, 100, 150DMLE615 (20HP) Synchronous Speed: 1800 RPM 3, 4, 6 inch Discharge
80,100,150CML615 (20 HP) Synchronous Speed: 1800 RPM 3, 4, 6 Inch Discharge
100 140
Curve No: F8-0132459-60-1
90 Solid Dia 3"
259 mm Impeller LL100
120
80
80DMLE615
70 100
EFFICIENCY
Total Head (Ft)
Efficiency (%)

60 100DMLE615
80

50

60
40 150DMLE615
Brake Horsepower (BHP)

30 25
40
BHP 20
20 15
20
10
10
5
0 0 0
0 200 400 600 800 1000 1200 1400
Capacity USGPM

EBARA Fluid Handling

www.pumpsebara.com 2-144
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Performance Curves
Project: GPM: TDH: EFF: HP: Chk’d: Date:

80, 100, 150DMLE622 (30HP) Synchronous Speed: 1800 RPM 3, 4, 6 inch Discharge
3, 4, 6 Inch Discharge
100 160
Curve No: F8-0132462-3-4
90 292 mm Impeller Solid Dia 3"
140 LL100

80 80DMLE622
120
70 100DMLE622
EFFICIENCY
100
Total Head (Ft)

60
Efficiency (%)

50 80
150DMLE622
40
60

Brake Horsepower (BHP)

30 BHP 30
40 25
20 20
15
20
10 10
5
0 0 0
0 200 400 600 800 1000 1200 1400 1600

Capacity USGPM

EBARA Fluid Handling

www.pumpsebara.com 2-145
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Dimensions
Project: Model: Chk’d: Date:
Model DMLEU f
80DMLEU, 3 to 30HP e
ø
100DMLEU, 5 to 30 HP
150DMLEU, 7.5 to 30HP

t
(n) QTY - (h) HOLES
C.O.L.
t Flange (ANSI 125 PSI F.F)
inch
ø e f t n h
3 6 71/2 3
/4 4 3
/4
4 71/2 9 15
/16 8 3
/4
6 91/2 11 1 8 3
/4
mm
ø e f t n h
80 150 185 19 4 19
100 175 210 20 8 19
150 240 280 22 8 19

Dimensions: inch
OUTPUT PUMP & MOTOR WEIGHT
PHASE SIZE MODEL Lb
ø kW HP A B C D E F H J L1
80DMLEU62.2 2.2 3 21 125/8 147/8 63/16 111/4 113/4 265/16 81/4 11 176
80DMLEU63.7 3.7 5 21 125/8 147/8 63/16 111/4 113/4 285/8 81/4 11 192
80DMLEU65.5 5.5 7.5 253/16 15 1713/16 73/8 143/16 131/8 327/16 101/16 123/16 260
3 80DMLEU67.5 7.5 10 253/16 15 1713/16 73/8 143/16 131/8 327/16 101/16 123/16 271
80DMLEU611 11 15 287/8 1715/16 203/16 811/16 169/16 133/4 3615/16 123/8 1215/16 346
80DMLEU615 15 20 287/8 1715/16 203/16 8 /16
11
16 /16
9
133/4 3615/16 123/8 1215/16 359
THREE
80DMLEU622 22 30 309/16 199/16 21 95/8 175/16 145/16 403/16 133/16 131/16 492
100DMLEU63.7 3.7 5 2211/16 125/8 169/16 63/16 123/8 125/16 285/8 81/4 11 196
100DMLEU65.5 5.5 7.5 2511/16 15 185/16 73/8 143/16 131/8 327/16 101/16 123/16 267
4 100DMLEU67.5 7.5 10 2511/16 15 185/16 7 /8
3
14 /16
3
131/8 327/16 101/16 123/16 276
100DMLEU611 11 15 293/8 1715/16 2011/16 811/16 169/16 133/4 3615/16 123/8 1215/16 353
100DMLEU615 15 20 293/8 1715/16 2011/16 8 /16
11
16 /16
9
133/4 3615/16 123/8 1215/16 366
100DMLEU622 22 30 311/8 199/16 217/16 95/8 175/16 145/16 403/16 133/16 131/16 498
150DMLEU65.5 5.5 7.5 281/16 15 2011/16 73/8 153/16 141/2 327/16 101/16 123/16 280
6 150DMLEU67.5 7.5 10 281/16 15 2011/16 73/8 153/16 141/2 327/16 101/16 123/16 291
150DMLEU611 11 15 313/4 1715/16 231/16 8 /16
11
17 /2
1
153/16 3615/16 123/8 1215/16 366
150DMLEU615 15 20 313/4 1715/16 231/16 811/16 171/2 153/16 3615/16 123/8 1215/16 379
150DMLEU622 22 30 337/16 199/16 2313/16 9 /8
5
18 /16
5
1511/16 403/16 133/16 131/16 511

Dimensions: mm
OUTPUT PUMP & MOTOR
PHASE SIZE
ø MODEL WEIGHT
kg
kW HP A B C D E F H J L1
80DMLEU62.2 2.2 3 534 320 378 157 285 298 668 210 279 80
80DMLEU63.7 3.7 5 534 320 378 157 285 298 727 210 279 87
80DMLEU65.5 5.5 7.5 640 381 453 188 360 334 824 255 310 118
80 80DMLEU67.5 7.5 10 640 381 453 188 360 334 824 255 310 123
THREE
80DMLEU611 11 15 734 455 513 221 420 350 938 315 329 157
80DMLEU615 15 20 734 455 513 221 420 350 938 315 329 163
80DMLEU622 22 30 777 497 533 245 440 363 1021 335 332 223
100DMLEU63.7 3.7 5 577 320 420 157 315 313 727 210 279 89
100DMLEU65.5 5.5 7.5 653 381 465 188 360 334 824 255 310 121
100 100DMLEU67.5 7.5 10 653 381 465 188 360 334 824 255 310 125
100DMLEU611 11 15 746 455 525 221 420 350 938 315 329 160
100DMLEU615 15 20 746 455 525 221 420 350 938 315 329 166
100DMLEU622 22 30 790 497 545 245 440 363 1021 335 332 226
150DMLEU65.5 5.5 7.5 713 381 525 188 385 369 824 255 310 127
150 150DMLEU67.5 7.5 10 713 381 525 188 385 369 824 255 310 132
150DMLEU611 11 115 806 455 585 221 445 385 938 315 329 166
150DMLEU615 15 20 806 455 585 221 445 385 938 315 329 172
150DMLEU622 22 30 850 497 605 245 465 398 1021 335 332 232

EBARA Fluid Handling

www.pumpsebara.com 2-146
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Dimensions
Project: Model: Chk’d: Date:
Model DMLEU with Quick Discharge Connector
80DMLEU62.2
80DMLEU63.7
100DMLEU63.7

Minimum manhole dimensions

in door frame installation 23/16 193/8 (492)
(56)

279/16 (700)
F
Guide pipe support
f
19/16 (40)

e
51/2 (140) Bolt 2– /2 x 1 /16 ø
1 3
Guide pipe 1''
(12x30)
23/8 (60)

t
(n) QTY - (h) HOLES
115/16 (50)
23/4 (70)

Flange (ANSI 125 PSI F.F)

23/4 (70) inch
C.O.L.
t ø e f t n h m
Guide pipe length

3 6 71/2 3
/4 4 3
/4 61/2
4 71/2 9 15
/16 8 3
/4 711/16
4 - 9/16 (15)Holes 415/16 (125)
mm
m
ø e f t n h m
P.C 39/16 (90) 215/16 (75) 80 150 185 19 4 19 165
.D.
61
/8 ( 100 175 210 20 8 19 195
155
)
11 / (285)

0)
3 (8
67/8 (175)
4
1

(20)
/16
13

Bolt 2 – 5/8 (16)

/8 (10)
3 39/16 215/16 /8 (10)
3

315/16 (100)
(90) (75)

Dimensions: inch
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb
PHASE ø MODEL
kW HP MODEL F L1 L6 PUMP Q.D.C.
80DMLEU62.2 2.2 3 LM80 125/8 11 1
/4 176 37
THREE 3
80DMLEU63.7 3.7 5 LM80 125/8 11 1
/4 192 37
4 100DMLEU63.7 3.7 5 LM80 125/8 11 1
/4 196 37

Dimensions: mm
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE ø MODEL
kW HP MODEL F L1 L6 PUMP Q.D.C.
80DMLEU62.2 2.2 3 LM80 320 279 7 80 17
THREE 80
80DMLEU63.7 3.7 5 LM80 320 279 7 87 17
100 100DMLEU63.7 3.7 5 LM80 320 279 7 89 17

EBARA Fluid Handling

www.pumpsebara.com 2-147
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Dimensions
Project: Model: Chk’d: Date:
Model DMLEU with Quick Discharge Connector
80DMLEU Minimum manhole
dimensions in door
100DMLEU frame installation
33/8 (85)

27 /16 (700)
F
9
Guide pipe support
Bolt 2–5/8 x 13/16
911/16 (246)
(16x30)
5 /8 (150)
7
Guide pipe 11/2''
315/16 (100)
23/4 (70)

65/16 (160)

C.O.L.
Guide pipe length

t f
e
ø
81/4 (210) 75/16 (185)

t
4 / (105) 41/8 (105)
1
8
P.C

4 – 3/4 (19)Holes
(n) QTY - (h) HOLES
.D.
6
7 8
/(
17

Flange (ANSI 125 PSI F.F)

5)

107/16 (265)

inch
ø4
(100 ø e f t n h
9 /16 (240)

)
D

3 6 71/2 3
/4 4 3
/4
7

4 71/2 9 15
/16 8 3
/4
Bolt 4 – 5/8 (16) mm
7 /16 (180)
1 ø e f t n h
19/16 811/16 315/16 80 150 185 19 4 19
Dimensions: inch (40) (220) (100) 100 175 210 20 8 19

SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb

PHASE ø MODEL
kW HP MODEL A D F L1 L6 DM PUMP Q.D.C.
80DMLEU65.5 5.5 7.5 LL100 243/4 143/8 15 123/16 11/4 311/2 260 101
80DMLEU67.5 7.5 10 LL100 243/4 143/8 15 123/16 11/4 311/2 271 101
3 80DMLEU611 11 15 LL100 283/8 143/8 17 /16
15
1215/16 9
/16 393/8 346 101
80DMLEU615 15 20 LL100 283/8 143/8 1715/16 1215/16 9
/16 393/8 359 101
80DMLEU622 22 30 LL100 301/8 143/8 19 /16
9
131/16 1
/2 393/8 492 101
THREE
100DMLEU65.5 5.5 7.5 LL100 243/4 143/8 15 123/16 11/4 311/2 267 101
100DMLEU67.5 7.5 10 LL100 243/4 143/8 15 123/16 11/4 311/2 276 101
4 100DMLEU611 11 15 LL100 283/8 143/8 1715/16 1215/16 9
/16 393/8 353 101
100DMLEU615 15 20 LL100 283/8 143/8 1715/16 1215/16 9
/16 393/8 366 101
100DMLEU622 22 30 LL100 301/8 143/8 199/16 131/16 1
/2 393/8 498 101
Dimensions: mm
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE ø MODEL
kW HP MODEL A D F L1 L6 DM PUMP Q.D.C.
80DMLEU65.5 5.5 7.5 LL100 628 365 381 310 31 800 118 46
80DMLEU67.5 7.5 10 LL100 628 365 381 310 31 800 123 46
80 80DMLEU611 11 15 LL100 721 365 455 329 15 1000 157 46
80DMLEU615 15 20 LL100 721 365 455 329 15 1000 163 46
80DMLEU622 22 30 LL100 765 365 497 332 12 1000 223 46
100DMLEU65.5 5.5 7.5 LL100 628 365 381 310 31 800 121 46
100DMLEU67.5 7.5 10 LL100 628 365 381 310 31 800 125 46
THREE 100 100DMLEU611 11 15 LL100 721 365 455 329 15 1000 160 46
100DMLEU615 15 20 LL100 721 365 455 329 15 1000 166 46
100DMLEU622 22 30 LL100 765 365 497 332 12 1000 226 46

EBARA Fluid Handling

www.pumpsebara.com 2-148
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Dimensions
Project: Model: Chk’d: Date:
Model DMLEU with Quick Discharge Connector
150DMLEU
Minimum manhole
dimensions in door
frame installation
33/8 (85)

279/16 (700)
F
Guide pipe support
Bolt 2–5/8 x 13/16
911/16 (246)
(16x30)
57/8 (150) Guide pipe 11/2''
315/16 (100)
23/4 (70)

65/16 (160)

C.O.L.
Guide pipe length

91/4 (235) 75/16 (185)

4 /8 (105) 41/8 (105)

1
P.C

4 – 3/4 (19)Holes
.D.
6
7 8
/(
175
)

f
107/16 (265)

ø4
e
(100 ø
97/16 (240)

)
D

t
Bolt 4 – 5/8 (16)
(n) QTY - (h) HOLES
7 /16 (180)
1

19/16 811/16 315/16

Flange (ANSI 125 PSI F.F)
(40) (220) (100) inch
ø e f t n h
6 91/2 11 1 8 3
/4
mm
ø e f t n h
150 240 280 212 8 19

Dimensions: inch
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT Lb
PHASE MODEL
ø kW HP MODEL A D F L1 L6 DM PUMP Q.D.C.
150DMLEU65.5 5.5 7.5 LL100 243/4 153/4 15 123/16 11/4 311/2 280 101
150DMLEU67.5 7.5 10 LL100 243/4 153/4 15 123/16 11/4 311/2 291 101
THREE 6 150DMLEU611 11 115 LL100 283/8 153/4 1715/16 1215/16 9
/16 393/8 366 101
150DMLEU615 15 20 LL100 283/8 153/4 1715/16 1215/16 9
/16 393/8 379 101
150DMLEU622 22 30 LL100 301/8 153/4 199/16 131/16 1
/2 393/8 511 101

Dimensions: mm
SIZE OUTPUT Q.D.C. PUMP & MOTOR WEIGHT kg
PHASE MODEL
ø kW HP MODEL A D F L1 L6 DM PUMP Q.D.C.
150DMLEU65.5 5.5 7.5 LL100 628 400 381 310 31 800 127 46
150DMLEU67.5 7.5 10 LL100 628 400 381 310 31 800 132 46
THREE 150 150DMLEU611 11 115 LL100 721 400 455 329 15 1000 166 46
150DMLEU615 15 20 LL100 721 400 455 329 15 1000 172 46
150DMLEU622 22 30 LL100 765 400 497 332 12 1000 232 46

EBARA Fluid Handling

www.pumpsebara.com 2-149
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Sectional View
Project: Model: Chk’d: Date:
80DMLE62.2

811
811 2
1
120 904
5
817
876
120
4
115
802 4
849
801 2

814
830

907 120
6

120 849
3 1
135 120 115
2 1 3
115 816
2
115 909 909
1 1 2

174 193 117

2
120
211 2

039 111

135 275
1
016
117
1
001
107

120 021
7
080

PART NO. FOR PART NO. FOR

NO. PART NAME MATERIAL 1 UNIT NO. PART NAME MATERIAL 1 UNIT
909-2 ELECTRODE HOLDER PVC 1 120-7 BOLT SUS304 4
909-1 ELECTRODE SUS304 1 120-6 BOLT SUS304 3
907 BEARING COVER SPCC 1 120-5 BOLT SUS304 2
904 LIFTING HANGER SS400 1 120-4 BOLT SUS304 4
876 AUTO CUT — 1 120-3 BOLT SUS304 4
849-2 BALL BEARING — 1 120-2 BOLT SUS304 8
849-1 BALL BEARING — 1 120-1 BOLT SUS304 4
830 SHAFT SUS403 1 117-2 SEAL WASHER NBR/304 1
817 OPPOSITE SIDE BRACkET FC200 1 117-1 FLANGE GASkET — 1
816 POWER SIDE BRACkET FC200 1 115-4 O-RING NBR 1
814 MOTOR FRAME FC200 1 115-3 O-RING NBR 1
811-2 SUBMERSIBLE CABLE — 1 115-2 O-RING NBR 1
811-1 SUBMERSIBLE CABLE — 1 115-1 O-RING NBR 1
802 STATOR — 1 111 MECHANICAL SEAL — 1
801 ROTOR — 1 107 WEARING RING CAC406 1
275 IMPELLER BOLT SUS304 1 080 BUSHING SS400 1
211 AIR VENT VALVE C3604 1 039 kEY SUS420J2 1
193 OIL PLUG SUS304 1 021 IMPELLER FC200 1
174 DISCHARGE PIPE FC200 1 016 MECHANICAL SEAL COVER FC200 1
135-2 WASHER SUS304 4 001 CASING FC200 1
135-1 WASHER SUS304 1

EBARA Fluid Handling

www.pumpsebara.com 2-150
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Sectional View
Project: Model: Chk’d: Date:
5 to 10 HP
80DMLE 811
2
100DMLE 811
1
150DMLE 120 904
5
817

120
856 4
115
802 4
849
801 2

830 814

907 120
6

120 849
3 1

135 120 115

2 1 3

115 816
2
115 909 909
1 1 2

174 193 117

2
120
211 2

039 111

135 275
1
117 016
1
001
107

120 021
7
080

PART NO. FOR PART NO. FOR 1

NO. PART NAME MATERIAL 1 UNIT NO. PART NAME MATERIAL UNIT
909-2 ELECTRODE HOLDER PVC 1 120-7 BOLT SUS304 4
909-1 ELECTRODE SUS304 1 120-6 BOLT SUS304 3
907 BEARING COVER SPCC 3 120-5 BOLT SUS304 2
904 LIFTING HANGER SS400 1 120-4 BOLT SUS304 4
856 THERMAL PROTECTOR — 2 120-3 BOLT SUS304 4
849-2 BALL BEARING — 1 120-2 BOLT SUS304 8
849-1 BALL BEARING — 1 120-1 BOLT SUS304 4
830 SHAFT SUS403 1 117-2 SEAL WASHER NBR/304 1
817 OPPOSITE SIDE BRACkET FC200 1 117-1 FLANGE GASkET — 1
816 POWER SIDE BRACkET FC200 1 115-4 O-RING NBR 1
814 MOTOR FRAME FC200 1 115-3 O-RING NBR 1
811-2 SUBMERSIBLE CABLE — 1 115-2 O-RING NBR 1
811-1 SUBMERSIBLE CABLE — 2 115-1 O-RING NBR 1
802 STATOR — 1 111 MECHANICAL SEAL — 1
801 ROTOR — 1 107 WEARING RING CAC406 1
275 IMPELLER BOLT SUS304 1 080 BUSHING SS400 1
211 AIR VENT VALVE C3604 1 039 kEY SUS420J2 1
193 OIL PLUG SUS304 1 021 IMPELLER FC200 1
174 DISCHARGE PIPE FC200 1 016 MECHANICAL SEAL COVER FC200 1
135-2 WASHER SUS304 4 001 CASING FC200 1
135-1 WASHER SUS304 1

EBARA Fluid Handling

www.pumpsebara.com 2-151
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Sectional View
Project: Model: Chk’d: Date:
15 to 30HP
80DMLE
100DMLE
150DMLE 904

120
811 4
1
849
811 2
2
115
817 4

120 856
4

802 814

801
849
830 1
115
907 120 3
6
909 909 120
2 1 3

117 193
2
115 816
2
120 111
1
120 135
115 2 2
1

174
016
211

135 275 039

1
117 001
1
021
080

120 107
7

PART NO. FOR PART NO. FOR 1

NO. PART NAME MATERIAL 1 UNIT NO. PART NAME MATERIAL UNIT
909-2 ELECTRODE HOLDER PVC 1 120-7 BOLT SUS304 4
909-1 ELECTRODE SUS304 1 120-6 BOLT SUS304 3
907 BEARING COVER SPCC 3 120-5 BOLT SUS304 2
904 LIFTING HANGER SS400 1 120-4 BOLT SUS304 6
856 THERMAL PROTECTOR — 2 120-3 BOLT SUS304 4
849-2 BALL BEARING — 1 120-2 BOLT SUS304 4
849-1 BALL BEARING — 1 120-1 BOLT SUS304 8
830 SHAFT SUS403 1 117-2 SEAL WASHER NBR/304 1
817 OPPOSITE SIDE BRACkET FC200 1 117-1 FLANGE GASkET — 1
816 POWER SIDE BRACkET FC200 1 115-4 O-RING NBR 1
814 MOTOR FRAME FC200 1 115-3 O-RING NBR 1
811-2 SUBMERSIBLE CABLE — 1 115-2 O-RING NBR 1
811-1 SUBMERSIBLE CABLE — 2 115-1 O-RING NBR 1
802 STATOR — 1 111 MECHANICAL SEAL — 1
801 ROTOR — 1 107 WEARING RING CAC406 1
275 IMPELLER BOLT SUS304 1 080 BUSHING SS400 1
211 AIR VENT VALVE C3604 1 039 kEY SUS420J2 1
193 OIL PLUG SUS304 1 021 IMPELLER FC200 1
174 DISCHARGE PIPE FC200 1 016 MECHANICAL SEAL COVER FC200 1
135-2 WASHER SUS304 4 001 CASING FC200 1
135-1 WASHER SUS304 1

EBARA Fluid Handling

www.pumpsebara.com 2-152
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Data
Project: Model: Chk’d: Date:
Models DMLEU
Three Phase
3 to 30HP
!"#$"%&%'$()'*%'+,-.)
!"#$$%&"'($ 60HZ
)*+, 208/230V

-'.$/0'1$%2'1345 671/71 +& 8 9 :; <* <9 =* 8*

>? =@= 8@: 9@9 :@9 << <9 ==
&"'($ 8 8 8 8 8 8 8
&A0$( B B B B B B B
CA01( C =*DE=8* =*DE=8* =*DE=8* =*DE=8* =*DE=8* =*DE=8* =*DE=8*
F./$#$( F <*@8EG@D <)@=E<9@B =8@:E=8@* 8*@BE=G@D B=@DEB<@= 9:@)E9B@) :D@)E:8@=
H/$$I .34J< <:**E<:=* <:**E<:=* <:=9E<:B* <:89E<:9* <:B9E<:9* <:9*E<:)* <:)9E<::*
K4(70'13A4%L0'(( M M M M M M M
L'/'N31A# H1'#1 OM P P P P P P P
274 OM P P P P P P P
-A%QA'I%!$(1 F./$#$( F 8@99EB@BB 9@B8E)@DB G@*GE<<@)B <<@=9E<B@98 <8@B)E<:@)B <:@<8E==@=* =<@=DE=)@G:
?'11( ? )9*E:9* :9*E<<** <=**E<B** <=**E<B9* <<:9E<)** <:D*E=<9* <D**E=<**
2$(3(1'4N$%'1%=*RL S <@DG *@G:9 *@9*= *@89B *@=9: *@<)B *@*D8
<**T%QA'I F./$#$( F <*@8EG@D <)@=E<9@B =8@:E=8@* 8*@BE=G@D B=@DEB<@= 9:@)E9B@) :D@)E:8@=
UVV3N3$4NW T ))@)DE)B@)D )G@G)E)G@*8 :=@DGE:<@<8 ::@BDE:B@G* D*@BDE:D@=) D*@=8E:G@=: D)@B9ED)@)8
&AX$#%M'N1A# T DG@8=ED)@=D G*@=BED:@=D DD@=GEDB@<8 DD@<9EDB@<= DD@B<ED9@B) DG@DDED)@D* DG@DBED:@BG
H/$$I .34J< <:*=E<:=< <:*:E<:=D <:8=E<:B8 <:B8E<:99 <:BDE<:9: <:9BE<:)8 <:):E<::8
QAN>$I%2A1A#%!A#Y7$ T <DBE=<G =*9E=B9 =8=E=:D =8:E=D: <98E<DB <)DE=*< <BBE<:8
H1'#1345%L7##$41 F BD@BE98@* DD@:EG:@D <9*@:E<))@) =*G@GE==G@) =B*@8E=)B@) 8:9@*EB<8@D 9=D@)E9DB@B
-7.Z$#%H1'#ƚ(%&$#%+A7# =* =* =* =* =* =* =*
[$(354%H1'4I'#I \UL8:
CA01'5$%!A0$#'4N$ T J<*%1A%)T ]<*T ]<*T ]<*T ]<*T ]<*T ]<*T
M#$Y7$4NW%!A0$#'4N$ T ]9T ]9T ]9T ]9T ]9T ]9T ]9T

EBARA Fluid Handling

www.pumpsebara.com 2-153
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Data
Project: Model: Chk’d: Date:
Models DMLEU
Three Phase
3 to 30HP
60HZ
460V

Model ZDLX (DL) ZDLX (DL) ZDLX (DL) ZDLX (DL) ZDLX (DL) ZDLX (DL) ZDLX (DL)
HP 3 5 71/2 10 15 20 30
Output
kW 2.2 3.7 5.5 7.5 11 15 22
Phase 3 3 3 3 3 3 3
Name-
Plate Poles 4 4 4 4 4 4 4
Rating
Volts V 460 460 460 460 460 460 460
Amperes A 4.9 7.7 11.5 14.9 20.6 27.3 36.6
Speed min–1 1720 1720 1740 1750 1750 1760 1770
Insulation Class F F F F F F F
Start — — — — — — —
Capacitor µF
Run — — — — — — —
No Load Amperes A 2.22 3.42 5.82 7.27 8.82 11.1 13.48
Test Watts 750 1100 1400 1450 1600 2150 2100
Resistance at
OHMS Ω 6.953 3.592 1.842 1.248 0.863 0.549 0.289
20°C
Current Amp. 4.9 7.7 11.5 14.9 20.6 27.3 36.6
100% Efficiency % 64.68 69.03 71.13 74.9 78.26 79.27 86.63
Load Power Factor % 86.28 87.28 84.13 84.12 85.46 86.8 87.49
Speed min–1 1721 1728 1743 1755 1757 1763 1773
Locked Rotor Torque % 222 248 278 287 184 201 173
Starting Current A 26.5 48.9 83.3 114.8 132.3 206.9 292.2
Number Starts Per Hour 20 20 20 20 20 20 20
Design Standard JEC37
Voltage Tolerance % -10 to +6% ±10% ±10% ±10% ±10% ±10% ±10%
Frequency Tolerance % ±5% ±5% ±5% ±5% ±5% ±5% ±5%

EBARA Fluid Handling

www.pumpsebara.com 2-154
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Specification
Project: Model: Chk’d: Date:

Power Cable Specification

OUTPUT DETAILS OF CONDUCTOR
INSULATOR SHEATH CONDUCTOR
PHASE VOLTAGE GAUGE NUMBER Q’TY/DIA. OF CABLE O.D.
DIAMETER THICkNESS THICkNESS RESISTANCE
V mm2 OF COND. WIRE mm
HP kW mm mm mm at 20 Ω/km
PCS/mm

3 2.2 THREE 208/230/460 2 4 37/0.26 1.8 0.8 1.8 11.8 9.79

4 37/0.26 1.8 0.8 1.8 11.8 9.79

5 3.7 THREE 208/230/460 2
3 37/0.26 1.8 0.8 1.8 10.9 9.79
4 45/0.32 2.5 0.8 2 13.9 5.24
71/2 5.5 THREE 208/230/460 3.5
3 45/0.32 2.5 0.8 1.9 12.6 5.24
4 45/0.32 2.5 0.8 2 13.9 5.24
10 7.5 THREE 208/230/460 3.5
3 45/0.32 2.5 0.8 1.9 12.6 5.24
4 45/0.32 2.5 0.8 2 13.9 5.24
15 11 THREE 208/230/460 3.5
3 45/0.32 2.5 0.8 1.9 12.6 5.24
4 70/0.32 3.1 1 2.1 16.5 3.37
20 15 THREE 208/230/460 5.5
3 70/0.32 3.1 1 2 15 3.37
4 88/0.45 4.9 1 2.4 22 1.43
30 22 THREE 208/230/460 14
3 88/0.45 4.9 1 2.3 20 1.43

Sensor Cable Specifications

OUTPUT DETAILS OF CONDUCTOR
INSULATOR SHEATH CONDUCTOR
PHASE VOLTAGE GAUGE NUMBER Q’TY/DIA. OF CABLE O.D.
DIAMETER THICkNESS THICkNESS RESISTANCE
V AWG OF COND. WIRE mm
HP kW mm mm mm at 20 Ω/km
PCS/mm
3 2.2
THREE 208/230/460 #16 2 50/0.18 1.25 0.8 1.7 9.6 15.1
5-30 3.7-22 4 11 1.8 11.1

EBARA Fluid Handling

www.pumpsebara.com 2-155
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Wiring Diagram P

Project: Model: Chk’d: Date:

Output 3HP
208/230V

EBARA Fluid Handling

www.pumpsebara.com 2-156
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Wiring Diagram P
Project: Model: Chk’d: Date:

Output 3HP
460V

EBARA Fluid Handling

www.pumpsebara.com 2-157
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Wiring Diagram P
Project: Model: Chk’d: Date:

Output 5, 7.5, 15, 20, 30HP

208/230V

EBARA Fluid Handling

www.pumpsebara.com 2-158
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
Motor Wiring Diagram P
Project: Model: Chk’d: Date:

Output 5, 7.5, 15, 20, 30HP

460V

EBARA Fluid Handling

www.pumpsebara.com 2-159
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
P
Motor Wiring Diagram
Project: Model: Chk’d: Date:

Output 10HP
208/230V

EBARA Fluid Handling

www.pumpsebara.com 2-160
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13
EBARA Submersible Wastewater Pumps DMLEU
P
Motor Wiring Diagram
Project: Model: Chk’d: Date:

Output 10HP
460V

EBARA Fluid Handling

www.pumpsebara.com 2-161
(803) 327-5005 • (803) 327-5097 (fax) rev. 01/13