Case 2: FIT AP Connect the Ethernet cable to your PC/Laptop and the LAN DATA

Hardware Connection Configuration

Safety Instructions Overview LED Indicators Installation Work Mode FIT mode means that the AP is centrally controlled and managed IN port of your PoE converter, then you can start the configuration
by the WAVLINK AC (Wireless Access Point Controller). If it work of the device.
Always read the safety instructions carefully. A1. Fasten the main body holder. 1. Connection
This AP supports two work modes: FAT mode and FIT mode. as a Fit AP, which is typically responsible only for data 2.Technically speaking, the product web UI will guide you to the
Keep this Quick Start Guide for future reference. transmission and basic radio frequency management. All network A2. Plug the device into the holder. 1.1 Via Wireless
ON The device is powered on. Here is a brief introduction to the two work modes: login page once you have connected to the device successfully
Keep this equipment away from humidity. decisions, configurations, security, and traffic control operations are A3. Connect one end of an Ethernet cable to “ PoE” port of PoE
POWER Case 1: FAT AP in your first time, but if it doesn't, please manually input
If any of the following situation arises, get the equipment OFF The device is not receiving electrical power. handled by the WAVLINK AC Controller. converter.
- FAT mode means that the AP can be independently configured 192.168.10.1 or waplogin.link in the address bar of your
checked by a service technician: Fit APs are typically used in an AC+AP network architecture and A4. Connect one end of an Ethernet cable to “LAN DATAIN” port
ON The Ethernet port is connected. and has a separate management interface, just like a regular browser on PC/laptop or phone, the default password is admin.
• The equipment has been exposed to moisture. wireless AP. can only be utilized with the WAVLINK wireless access point of PoE converter, and connect the other end to a “LAN” port
• The equipment has been dropped and damaged. WAN/LAN OFF The Ethernet port is disconnected. of your Router.
- FAT mode is primarily used in small networks that do not use controller, as shown in the diagram below.
• The equipment has obvious sign of breakage. A5. Plug the Power Adapter into the power outlet.
QUICK START GUIDE
Flashing Transferring data to/from a network device. an AC Controller. Router
• The equipment has not been working well or you cannot get A6. Push the “ON/OFF” button on the PoE converter to power on.
it work according to Quick Start Guide. 5
Turn on your Wi-Fi, search SSID of this product on your wireless
devices (smart phone, tablet computer, laptop, etc.) and connect
AC600 Dual Band Outdoor 2.4G/5G 2.4G/5G
to it.
Copyright Statement
Router/AP/Repeater No part of this publication may be reproduced in any form by
Wi-Fi Signal 4
PoE switch
Wavlink Wireless Access
any means without the prior written permission. 2 4G/5G RP- SMA Antenna Connectors POWER LED Point Controller Wi-Fi:On
6
Other trademarks or brand names mentioned herein are Wi-Fi Signal LED Reset Button Not connected
Turn Wi-Fi Off
3
trademarks or registered trademarks of their respective WAVLINK-N_XXXX
Wi-Fi LED WAN/LAN Port (PoE) LED Mode 7 Connections are available
companies. WAVLINK-AC_XXXX
WAN/LAN LED Grounding Terminal Here are several typical work modes for Fat AP:
Wireless Network Connection
2
AP/Router ON ON ON Wi-Fi signal output power 100%. 8 AP1 AP2 AP3 WAVLINK-N_XXXX Join Other Network....
Disclaimer AP/Router Mode WAVLINK-AC_XXXX Create Network....
Information in this document is subject to change without notice. ON ON ON Better reception: signal 81%~100%. FIT mode is ideal for larger networks with broader coverage, a
Basic Info 1 A1 A2 Connect automatically Connect Open Network Preferences... 3.Select your Country/Region and Time Zone. For your network
The manufacturer does not make any representations or higher number of users, and a need for efficient network
ON ON OFF Good reception: signal 60%~80%. For Windows users For Mac users security, we suggest that you set a new login password.
warranties (implied or otherwise) regarding the accuracy and performance and enhanced security.
Repeater
completeness of this document and shall in no event be liable for Official Website: www.wavlink.com ON Pass RJ45 cable through Spin 2.4G/5G antenna into the 1.2 Via Cable
OFF OFF Weak reception: signal below 0~59%.
any loss of profit or any commercial damage, including but not 5G SSID: WAVLINK-AC_XXXX the spiral cover. 2.4G/5G external RP-SMA
limited to special, incidental, consequential, or other damage. 2.4G SSID: WAVLINK-N_XXXX Flashing OFF OFF Disconnected. connector.
Pass RJ45 cable through
Default IP: 192. 168.10.1
the rubber seal. Screw up the holder. Router/Modem AP/Router
www.wavlink.com/en_us/AERIAL-HD2 Pro Login: waplogin.link Repeater Mode
A6 A5
Default Password: admin Pass RJ45 cable through Plug the rubber seal into the A4
Scan the QR code or load the link for A3
Technical Support: support@wavlink.com the holder. holder.
Quick Start Guide downloading Connect the RJ45 cable to PoE
Screw up the spiral cover. Converter
RJ45 port. 4
3

AERIAL-HD2 Pro 1

Po E
2
Note: The three colored bars in “Admin Password” area
Router Repeater
Converter indicates the strength of the login password.
01 02 03 04 05 06 07 08 09

4. Mode Selection 4.2 Repeater Mode Manual Input: 4.3 Router Mode 4. Click on to locate the firmware file.
This product has 3 modes. 1. Click on “Switch mode”, Please choose “Repeater Mode”. 1. Manually add the wireless network you want to relay, enter the 1. Click on“Switch mode”. Please choose“Router Mode”. 5. Click on “Upload” and choose “Apply”, and wait for the firmware Lightning and ESD Protection FAQ GNU (General Public License Notice)
4.1 AP Mode(LAN Bridge) 2. After scanning, please make sure the Wi-Fi you want to select device information, and click “Next” . 2. Before configuring. please make sure your upper router has upgrade process to complete. Lightning and ESD Protection is important for safety, so proper Q1. What can I do if I can not access the Internet? This product includes software codes developed by third
is listed, and click “Next”, if it isn't, please click“Rescan”. connected to the WAN port of this product. The system will Option II grounding is extremely important for outdoor devices. - Make sure your Internet works normally, please contact your
The system selects AP mode by default, there is no need to parties.These software codes are subiect to either the GNU
guide you to select the WAN Type. As for the Encryption Mode, To reduce potential damage from lightning strikes and ESD, ISP(Internet Service Provider) if it doesn't. General Public License (GPL), V June 1991 or the GNU Lesser
select the AP mode manually. Click on“Next” . 1.Log in to 192.168.10.1 or waplogin.link, then choose “Advanced”
we recommend you to select WPA2-PSK. For you network please use a suitable grounding wire to connect the grounding - Initiate your browser, enter 192.168.10.1 or http://waplogin.link, General Public License (LGPL)V February 1999.You can
1.Log in to 192.168.10.1 or waplogin.link. and select “Firmware Update”.
security, we suggest you create a Password. terminal to the grounding facility before installing this product. then set up the following quick start guide. copydistribute,and/or modify in accordance with the terms.
2.Click on “Check New Version” to find the latest version.
And the grounding wire should meet the local installation - Reboot your device and try it again. and conditions of GPL or LGPL.
3.Click on “Download and Upgrade”, and wait for the firmware
requirements. You should use screws to secure the grounding Q2. Why can't I visit the web UI by inputting the IP address The source code should be complete, if you want us to provide
upgrade process to complete.
wire to the grounding terminal. 192.168.10.1 or waplogin.link? any additional source code files under GNU General Public
- If you can't log in to the IP address or URL in AP Mode, please License (GPL), please contact us in these matters.We are
check the IP address arranged by the upstream router, then try to committed to meeting the requirements of the GNU Genera
restart the process. Public License (GPL). You are welcome to contact our local
- Make sure you have connected to the WiFi of the Wavlink device. office to get the corresponding software and licenses. Please
- Please try to clean the cache of the browser. inform us of your contact details(full address) and the product
Firmware Upgrade - Try to log in the management page via another browser. code.We will send you a software package with the software
3. Enter the password for the wireless network you have selected.
Set the wireless network encryption mode and password for this 2.Set the wireless network encryption mode and password for this
If you need to update firmware, please proceed as the following
- Try to log in the management page via other devices.
Q3. What can I do if I forget my administration management
and license for free.
The respective programs are distributed WITHOUT ANY
Thank you
for purchasing
steps: password? WARRANTY; without even the implied warranty of MERCHANT
2. You can change the SSID or use the default one, as for the device. Click “Save”. device. Click “Save”. Grounding Terminal
Option I - While the device is powered on, press and hold the Reset Button ABILITY Or FITNESS FOR A PARTICULAR PURPOSE
Encryption Mode, the default is WPA2-PSK. For your network 1. Download the latest firmware file from Wavlink website.
WAVLINK product!
until all the LEDs turn on momentarily. The default password is Please refer to the GNU General Public License website for
security, please set a new password according to the rule. 2. Extract the firmware from the downloaded file.
Which WAN Type am I supposed to choose? admin. further informmation.
Then click on“Save” and wait for the setting process to 3. Log in to waplogin.link or 192.168.10.1, then choose
complete. If you use DSL line and you are only provided an account name http://www.gnu.org/licenses/old-licenses/lgpl-2.0.htm
and a password by your ISP, choose PPPoE. “Advanced” and select “Firmware Update”. http://www.gnu.org/licenses/gpl.html
If you use cable TV or fiber cable, choose DHCP (Dynamic IP).
If you are provided information such as IP address, Subnet At the end of its serviceable life, this product
Note: After updating firmware, please Reset The Device And should not be treated as household or general
Mask and Default Gateway, choose Static IP. Clear Your Browser Cache. waste. It should be handed over to the applicable Official website: www.wavlink.com
collection point for the recycling of electrical and
What is firmware upgrade and why do I need it? electronic equipment,or returned to the supplier for Technical support: support@wavlink.com
Firmware contains fixed for bugs and new features, please keep disposal.
Wi-Fi Password Management the latest firmware to improve the experience of using the product.
Please do not use the wrong firmware, otherwise, it will damage
When you need to change your Wi-Fi password, please click on your device and void the product warranty.
“Wireless”. For more details, please visit our website www.wavlink.com
Our Technical Support: support@wavlink.com

10 11 12 13 14 15 16 17 18