"EUROPE" compact cylinders Series 1500
General
This series of cylinders is available in two versions with different threaded fixing holes.
The first one includes cylinders from Ø 32 to Ø 100 called "ISO" with fixing holes same as cylinders ISO 6431 -
VDMA 24562. Cylinders from Ø 20 to Ø 100 called "UNITOP", parts of second series, are mainly according to
standard UNITOP RU - P/6 - P/7. Cylinders Ø 12 and Ø 16 non standard, are interchangeable with similar products
available on the market. The ISO version uses all fixing devices of series 1320 with exception of intermediate
trunnion, while for cylinders Ø 12, Ø 16 and for "UNITOP" version are available fixing devices as flanges, foot, male
and female clevis made with aluminium or steel. For use of magnetic sensors see directions on next page.
Construction characteristics
Body anodised aluminium
Heads from Ø12 to Ø25 aluminium alloy UNI 9006/1 anodised
from Ø32 to Ø100 UNI 5076 aluminium die-casting and painted (cataphoresis)
Piston rod bushing sintered bronze
Piston rod from Ø12 to Ø25 stainless steel
froml Ø32 to Ø100 C43 chromed (on request stainless steel for all bores)
from Ø12 to Ø25 plated zinc steel
Piston
dal Ø32 al Ø100 aluminium alloy 2011 UNI 9002/5
Seals PUR (on request HNBR)
Spring zinc plated steel for springs
Fixing screws zinc plated steel
Technical characteristics
Fluid filtered air, with or without lubrication
Maximum working pressure 10 bar
Working temperature -30°C - +80°C with standard seals (magnetic or non magnetic piston)
-5°C - +80°C with HNBR seals (magnetic piston)
-5°C - +120°C with HNBR seals (non magnetic piston)
4
Please follow the suggestions below to ensure a long life for these cylinders:
•use clean and lubricated air
•correct alignment during assembly with regard to the applied load so as to avoid radial components
or bending the rod.
•avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder
cannot absorb, especially if used as a limit stop (in this case use mechanical stop device)
•evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.)
Please note: air must be dried for applications with lower temperature.
Use hydraulic oils H class (ISO Vg32) for correct continued lubrication.
Our Technical Department will be glad to help.
Standard strokes for single acting cylinders Standard strokes for double acting cylinders
Ø12 10 mm max. Ø12 and Ø16 from 5 to 40mm every 5mm
from Ø16 to Ø100 25 mm max. Ø20 and Ø25 from 5 to 50mm every 5mm
Ø32 - Ø100 from 5 to 80mm every 5mm
Maximum suggested strokes Maximum suggested strokes with non-rotating device
Ø12 and Ø16 100 mm from Ø12 to Ø25 40 mm
Ø20 and Ø25 200 mm from Ø32 to Ø100 80 mm
Ø32 and Ø40 300 mm
Ø50 and Ø63 400 mm Minimum and maximum springs load
Ø80 and Ø100 500 mm
Bore 12 16 20 25 32 40 50 63 80 100
Longer strokes may be utilised if there is no
radial loads on piston rod considering Min. load (N) 3,9 4,4 4,9 9,8 12,3 16,7 27,5 37,3 59,4 101,3
there isn't adjustable cushioning system.
Max. load (N) 9,3 17,7 18,1 25,5 34,3 44,1 51,0 63,8 99,4 141,9
Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice. 4.130
Series 1500 "EUROPE" compact cylinders
BASIC version PL PL
double and single acting EE
Sensor slot detail
type “B”
MM
5.2
SW
TG
KF
E1
RT
E
DT
3.3
AF LB TG
6.6
BG E
WH ZA+stroke
for bores from Ø 12 to Ø 25
ZJ+stroke
use sensors codes
1580._, MHS._, MRS._ only
PL
Sensor slot detail
type “A” EE PL
16.2
12
5.5
2.5
MM
SW
E1
KF
TG
E
DT
RT
Sensor slot detail
type “B”
LB TG
for bores from Ø 32 to Ø 50 5.2
use sensors codes AF BG E
3.3
1500._, RS._, HS._ (slot A) WH ZA+stroke
1580._, MHS._, MRS._ 6.6
ZJ+stroke
(slot B and slot A with adapter code 1380.01F)
PL PL
EE
Sensor slot detail
type “A”
16.2
MM
SW
TG
E1
KF
E
12
5.5
2.5
RT
DT
for bores from Ø 63 to Ø 100
use sensors codes LB
TG
1500._, RS._, HS._ and AF BG
WH ZA+stroke E
1580._, MHS._, MRS._
ZJ+stroke
4
(with adapter code 1380.01F)
PUSH/PULL rod version
double and single acting
WH ZA+stroke WH+stroke
Tandem with opposite rods
WH U+stroke+stroke1 WH
Tandem push with common rods
WH U+2stroke
4.131 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice.
"EUROPE" compact cylinders Series 1500
W+stroke+stroke1
Opposed tandem with common rod
ZA+stroke Z ZA+stroke1
WH U+stroke+stroke1
Tandem push with independent rods
stroke
stroke1
Ordering code
Basic version push/pull Tandem version
15_ _. Ø . stroke . _ _ . _ 15_ _. Ø . stroke .(stroke1) . _
1 = Double acting (magnetic)
2 = Front spring (magnetic)
3 = Rear spring (magnetic) A = Tandem with opposite rods female thread
4 = Double acting (non magnetic) E = Tandem with opposite rods male thread
5 = Front spring (non magnetic) L = Tandem opposite rods with non rotating device on both sides
6 = Rear spring (non magnetic) C = Tandem push with common rods female thread
01 = Basic version - female piston rod G = Tandem push with common rods male thread
02 = Basic version - male piston rod H = Tandem push with common rods, push-pull version rod female threads
03 = Push / pull version - female piston rod N = Tandem push with common rods with non rotating device
04 = Push / pull version - male piston rod D = Opposed tandem with common rod
05 = Push / pull version - bored male piston rod B = Tandem push with independent rods female thread
06 = Push / pull version - bored female piston rod F = Tandem push with independent rods male thread
07 = Non - rotating version M =Tandem push with independent rods with non rotating device
08 = Push / pull version with non rotating device on P = Tandem push/pull with independent rods - female thread
one side - female piston rod * Q = Tandem push/pull with independent rods - male thread
09 = Push / pull version with non rotating device 1 = Chromed rod C43 (from Ø12 to Ø25 stainless steel)
on one side - male piston rod * 2 = Stainless steel rod(from Ø32 to Ø100)
1 = Chromed rod C43 (from Ø12 to Ø25 stainless steel)
6 = ISO (Ø32 - Ø100)
2 = Stainless steel rod(from Ø32 to Ø100)
4
7 = ISO HNBR (Ø32 - Ø100)
6 = ISO (Ø32 - Ø100) 8 = UNITOP (Ø12 - Ø100)
7 = ISO HNBR (Ø32 - Ø100) * for single acting version, 9 = UNITOP HNBR (Ø12 - Ø100)
8 = UNITOP (Ø12 - Ø100) the spring is on the
9 = UNITOP HNBR (Ø12 - Ø100) anti-rotation side
Table of dimensions Bore 12 16 20 25 32 40 50 63 80 100
AF 6 8 10 10 12 12 12 12 16 20
BG 19 19 20 20 17.5 17.5 19.5 19.5 23.5 24.5
DT 6 6 8 8 10 9 10.5 10.5 14 14
E 29 29 36 40 48 57 67 80 102 122
E1 30 30 37.5 41.5 49.5 58.5 69 82 105 125
EE M5 M5 M5 M5 G 1/8" G 1/8" G 1/8" G 1/8" G 1/8" G 1/4"
KF M3 M4 M5 M5 M6 M6 M8 M8 M 10 M12
LB 3.5 3.5 4,8 4.8 5,5 5.5 6.5 6.5 8.5 8.5
MM 6 8 10 10 12 12 16 16 20 25
PL 8 8 8 8 8 8 8 8 8.5 10.5
RT M4 M4 M5 M5 M6 M6 M8 M8 M 10 M 10
SW 5 7 8 8 10 10 13 13 17 22
TG ISO / / / / 32.5 38 46.5 56.5 72 89
TG UNITOP 18 18 22 26 32 42 50 62 82 103
U 76 76 76 79 89 91 91 100 112 133
W 85 85 85 90 101 104 106 115 128 153
WH 4.5 4.5 4.5 5.5 6 6.5 7.5 7.5 8 10
Z 9 9 9 11 12 13 15 15 16 20
ZA
* 38 38 38 39.5 44.5 45.5 45.5 50 56 66.5
ZJ
Weight *
stroke 0
42.5
88
42.5
90
42.5
140
45
170
50.5
210
52
320
53
460
57.5
690
64
1390
76.5
2290
gr. every 5 mm 8 8 12 13 15 19 25 31 50 66
* These dimensions increase of 10 mm for cylinders ø 12 front spring version.
Tabular weights above refer to Basic Versions. The weights of Tandem versions are approximately double those shown.
Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice. 4.132
Series 1500 "EUROPE" compact cylinders
Basic version male piston rod Push - pull version male rod
AM WH AM WH WH+stroke AM
KK
KK
ZA + stroke ZA+stroke
Push - pull version bored male piston rod Push - pull version bored female piston rod
AM WH WH+stroke AM
WH ZA+stroke WH+stroke
AF
D
KF
D
KK
ZA+stroke
Maximum allowed stroke = ZB (see table)
Non-rotating version
4 MF
L1 ZA+stroke C*
B
F
C*
B
A
FB
MN
* = Distance between rods centres
Bore 12 16 20 25 32 40 50 63 80 100
A 28.5 28.5 35.5 39.5 45 55 65 80 100 120
AF 6 8 10 10 12 12 12 12 16 20
AM 16 20 22 22 22 22 24 24 32 40
B 9.9 9.9 12 15.6 19.8 23.3 29.7 35.4 46 56.6
C 18 18 22 26 34 40.5 49 59.5 77 94
D 2.3 3.2 3.8 3.8 4.5 4.5 6 6 8 10
F 3 3 4 5 5 5 6 6 8 10
FB M3 M3 M4 M5 M5 M5 M6 M6 M8 M 10
KF M3 M4 M5 M5 M6 M6 M8 M8 M 10 M 12
KK M6X1 M8X1.25 M10X1.25 M10X1.25 M10X1.25 M10X1.25 M12X1.25 M12X1.25 M16X1.5 M20X1.5
L1 10.5 10.5 12.5 13.5 16 16.5 19.5 19.5 22 24
MF 6 6 8 8 10 10 12 12 14 14
MN 5 5 6 6 8 8 10 10 12 12
WH 4.5 4.5 4.5 5.5 6 6.5 7.5 7.5 8 10
ZA 38 38 38 39.5 44.5 45.5 45.5 50 56 66.5
ZB 20 25 50 50 50 50 75 75 80 80
4.133 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice.
