Am2d 1212DZ
Am2d 1212DZ
FEATURES:
Models
Single output
Input Voltage Output Voltage Output Current Isolation Efficiency
Model
(V) (V) max (mA) (VDC) (%)
AM2D-0503SZ 4.5-5.5 3.3 400 1000 72
AM2D-0505SZ 4.5-5.5 5 400 1000 78
AM2D-0507SZ 4.5-5.5 7.2 278 1000 80
AM2D-0509SZ 4.5-5.5 9 222 1000 80
AM2D-0512SZ 4.5-5.5 12 167 1000 82
AM2D-0515SZ 4.5-5.5 15 134 1000 82
AM2D-0518SZ 4.5-5.5 18 111 1000 82
AM2D-0524SZ 4.5-5.5 24 83 1000 82
AM2D-1203SZ 10.8-13.2 3.3 400 1000 65
AM2D-1205SZ 10.8-13.2 5 400 1000 77
AM2D-1207SZ 10.8-13.2 7.2 278 1000 80
AM2D-1209SZ 10.8-13.2 9 222 1000 80
AM2D-1212SZ 10.8-13.2 12 167 1000 82
AM2D-1215SZ 10.8-13.2 15 134 1000 82
AM2D-1218SZ 10.8-13.2 18 111 1000 80
AM2D-1224SZ 10.8-13.2 24 83 1000 80
AM2D-2403SZ 21.6-26.4 3.3 400 1000 72
AM2D-2405SZ 21.6-26.4 5 400 1000 79
AM2D-2407SZ 21.6-26.4 7.2 278 1000 80
AM2D-2409SZ 21.6-26.4 9 222 1000 80
AM2D-2412SZ 21.6-26.4 12 167 1000 80
AM2D-2415SZ 21.6-26.4 15 134 1000 82
AM2D-2418SZ 21.6-26.4 18 111 1000 82
AM2D-2424SZ 21.6-26.4 24 83 1000 82
Models
Single output (continued)
Input Voltage Output Voltage Output Current Isolation Efficiency
Model
(V) (V) max (mA) (VDC) (%)
AM2D-2415SH30Z 21.6-26.4 15 134 3000 82
AM2D-2418SH30Z 21.6-26.4 18 111 3000 82
AM2D-2424SH30Z 21.6-26.4 24 83 3000 80
Models
Dual separated output
Input Voltage Output Voltage Output Current Isolation Efficiency
Model
(V) (V) max (mA) (VDC) (%)
AM2D-050303DZ 4.5-5.5 3.3 / 3.3 200 / 200 1000 73
AM2D-050505DZ 4.5-5.5 5/5 200 / 200 1000 78
Input Specifications
Parameters Nominal Typical Maximum Units
5 4.5-5.5
Voltage range 12 10.8-13.2 VDC
24 21.6-26.4
Filter Capacitor
Turn on Transient process time 25 ms
Start up time 200 ms
5 Vin 0-7
Absolute Maximum Rating 12 Vin 0-15 VDC
24 Vin 0-28
Peak Input Voltage time 100 ms
Isolation Specifications
Parameters Conditions Typical Rated Units
Tested I/O voltage 3 sec 1000, 3000, 4000 and 5200 VDC
Resistance > 1000 MOhm
Capacitance 60 pF
Output Specifications
Parameters Conditions Typical Maximum Units
Voltage accuracy ±3 %
Voltage balance Dual output ±1 %
Short Circuit protection Momentary (1sec).
Line voltage regulation (Single) For 1.0% of Vin ±1.2 %
Line voltage regulation (Dual) For 1.0% of Vin ±1.2 %
Load voltage regulation (Single) Load 20~100% ±10 %
Load voltage regulation (Single)
Load 20~100% ±20 %
3.3V output model
General Specifications
Parameters Conditions Typical Maximum Units
Switching frequency 100% load 85 KHz
o
Operating temperature -40 to +75 C
o
Storage temperature -55 to +125 C
o
Max Case temperature +95 C
Cooling Free air convection
Humidity 90 %
Case material Plastic UL94-VO
Weight 2.5 g
Dimensions (L x W x H) 0.76 x 0.24 x 0.37 inch 19.50 x 6.00 x 9.50 mm
MTBF >688 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC)
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified
Safety Specifications
Parameters
Agency approvals CE (Except dual separated models)
EN55022 (Radiated Emissions) class B
Standards EN55024 (Noise Immunity), IEC61000-4-2(ESD)
IEC61000-4-3 (Radiated immunity)
Dimensions
19.50
(0.76) 6.00
(0.24)
PRINTED
FACE
9.50 10.00
(0.37) (0.39)
0.50
(0.02) 2.54 3.05
(0.10) (0.12)
15.20
(0.60)
0.50
(0.02)
6.00
(0.24) 0.50
(0.02)
0.25
(0.01)
1.25
(0.05)
Derating
Free Air Convection
75º C
100
80
Output Power (%)
40
20
0
85
- 40 - 20 0 20 40 60 80 100
Ambient Temperature º C
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer
controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary
based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C,
humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all
internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for
release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications
which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at
www.aimtec.com.