4.
Installation instructions 6
5. Power Wires connection 7
6. Device Parameter Settings 8
6.1 Initialization 8
6.2 Set password 8
6.3 Authorization 9
6.4 Single Locating 9
6.5 Auto continuous track 10
6.6 Voice Surveillance 10
6.7 Overspeed alarm 10
6.8 Geo-fence 11
6.9 ACC ON alarm 11
6.10 Time Zone Setting 11
6.11 GPRS setting 12
6.13 IP and Port setting 12
6.14 Cut oil or circuit (optional) 12
6.15 Recover oil or circuit 13
6.16 Power failure alarm (optional) 13
6.17 Check device setting parameters 13
6.18 Web platform GPS tracking software 13
◆Quick using
1）Proper insert GSM SIM card, connect to power supply 12V/24V, Must
turn on small switch inside SIM card hole.
2）Put device outside, around 45-90s three lights will keep lighting on
stands for device can work normally.
3）Dialing device number, it will hang up and reply tracking message with
valid Long and lat to show location.
4）Track online system need set two SMS as below:
SMS 1: #IP#123456#116.205.4.114#8169#
SMS2: #apn#123456#APN of operator#APN user name#APN password#
5）Login platform to track in real time(please contact supplier).
◆Installation attentions
NOTE: device front side towards the sky.
Installation: if the windscreen glued by metal thermal insulation layer or
heating layer, it will reduce the GPS receive signal and lead to GPS work
disorder.
1. Summary
Working Based on existing GSM/GPRS network and GPS satellites, this
product can locate and monitor any remote targets by SMS or GPRS.
2. Main functions
· GSM quad-band frequency;
· Real time tracking by SMS/GPRS;
· Real time voice monitoring;
· Overspeed alarm/ACC anti-theft alarm ;
· Connect relay to control vehicle oil or circuit (optional);
· Built-in backup battery to realize power cut alarm(optional);
3. Specs.
Content Specs.
Dim. 84 mm x47.5 mm x 15 mm
Weight 50g
Network GSM/GPRS/GPS
Band 850/900/1800/1900 Mhz
GPS chip MT3336
GSM module MT6260D
GPS sensitivity -159dBm
GPS accuracy 5m
Cold status 45s-90s
Time To First Fix Warm status 35s
Hot status 1s
Work voltage 12V-24V
Storage Temp. -40°C to +85°C
Operation Temp. -20°C to +45°C
Humidity 15%--95%
4. Installation instructions
4.1 Preparation
Choose a GSM SIM card insert into device.
Notice: Please insert SIM card before turning the device power
switch to on; The SIM card need open the GPRS function; Please make
sure SIM card with full balance.
4.2 Installation
The device is hidden type installation, we suggest the device installing by
professional institution. Please pay attention to the following points:
4.2.2 The device has built-in GSM and GPS antenna, make sure the
receive side upward and there is no metal shielding.
4.2.3 Recommended installation place: ①The hidden place in the board
below the front windscreen; ② The hidden place around former
dashboard (nonmetal material for skin); ③The hidden place in the board
below the back windscreen.
Notice: If the windscreen glued by metal thermal insulation layer or
heating layer, it will reduce the GPS receive signal and lead to GPS work
disorder, then please change the installation place.
4.3 Device light description
Light Signal working status
Red light Power Stable light on
Yellow light GSM signal Stable light on
Blue GPS signal Stable light on
Note: the three lights must be stable lighting on represent device can work
normally. Device will enter sleep mode with lights off around 5 minutes, it will
wake up if make a call to device number.
5. Power Wires connection
1. Red wire connects to vehicle power anode +
2. Black wire connects to vehicle power cathode -
3. Yellow wire connects to oil pump or circuit control wires
4. Green wire connects to ACC ignition wire
6. Device Parameter Settings
6.1 Initialization
Send SMS “#begin#password#” to the tracker, it will reply “begin ok”.
(Default password:123456).
For example, send SMS “#begin#123456# ”, If succeeded, it will
reply“begin ok”.
6.2 Set password
6.2.1Setup: Send SMS: “#password#old password#new password#” to
the unit to change the password.
For Example, send SMS: “#password#123456#666888#” to device, it
will reply SMS: “password OK”.
6.2.2 Make sure the new password is in 6 digits arabic numbers, or the
device cannot recognize the password.
6.2.3 Resume original password: send SMS: “#resume#” to the device, it
will reply SMS: “resume password, password is 123456”.
6.3 Authorization
6.3.1 Setup: send SMS“#admin#password#cell phone number#” to set
up authorized number, device will reply “admin ok”.
6.3.3 Delete authorization: send SMS“#noadmin#password#authorized
number#”to delete the authorized number, device will reply “no admin
ok”.
6.4 Single Locating
6.4.1 If there is no authorized number, any number dials up the device
number, it will report tracking message; If already set authorized number,
then it will not respond when an unauthorized number calls it.
6.4.2 Dialing tracking: make a call to device number, it will hang up and
reply a real-time tracking message as below picture:
6.4.3 SMS tracking: send SMS“#smslink#123456#”, it will reply a
real-time tracking message as below picture:
6.5 Auto continuous track
6.5.1 Setup time interval: Send SMS “#at#time interval#sum#0#” to the
device. Remark: device must be connected to tracking software.
For example, to set 30s time interval to upload data to platform, send
SMS: “#at#30#sum#0#” to device.
6.5.2 Cancel: Send SMS “#noat#password#” to the device, it will stop
sending data to platform.
6.6 Voice Surveillance
6.6.1 The command to switch between Track and Monitor are “tracker”
and “monitor
6.6.2. The default mode is “tracker mode” (Tracking status).
6.6.3. Send SMS “#monitor#password#” to the device, and it will reply
“monitor ok!” and switch to “monitor” mode. Then use mobile phone to
dial the device number, it will get through and enter voice listening
function.
6.6.4. Send SMS “#tracker#password#” to the device, it will reply
“tracker ok!” and restore to “track” mode.
6.7 Overspeed alarm
6.7.1 Set up: Send SMS:“#speed#password#speed number in 3 digits#”
to the device (suppose the speed is 80km/h), EG, send SMS
“#speed#123456#080#”, and it will reply “speed ok ”. When the car
moves exceeding 80 km/h, the unit will send SMS alert “speed alarm” to
the authorized number.
6.7.2 Cancel: send SMS “#nospeed#password#” to deactivate the
overspeed alarm. It will reply “cancel speed ok”.
6.8 Geo-fence
Set up geo-fence for the unit to restrict its movement within a district.
The device will send message to the authorized number automatically
when it exceed the district.
6.8.1 Setup:When the unit stays immobile in a place based on GPS
located, send SMS: “#stockade#password#semidiameter#”to unit to set
the restricted district. In case of breach, it will send SMS “stockade! +
Geo-info” to the authorized number.
For example, Send SMS: “#stockade#123456#3#”, “3” represents 300
meters.
6.8.2 Cancel: Send SMS: “#nostockade#password#” to deactivate this
function, it will reply “no stockade ok”.
6.9 ACC ON alarm
6.9.1 Send SMS"#ACC#ON#" to device to start illegal start alarm
function, when vehicle ignition on, device will reply "ACC!!" to the
authorized number.
6.9.2 Send SMS"#ACC#OFF#"to device to cancel the function.
6.10 Time Zone Setting
Remark: UTC+8 is default time zone.
6.10.1 Send SMS “#timezone#password#E or W#time zone
number#time zone munites#”. If set OK, it will reply “time zone ok”.
For example, if in UTC-6, send SMS “#timezone#123456#W#6#00#”. If
in UTC+5.30, send SMS “#timezone#123456#E#5#30#”.
6.11 GPRS setting
User must send SMS via cell phone to set IP, port and APN before
starting GPRS.
6.12.1 Setting APN
6.12.1.1 APN standards for Access Point Name and differs from country
to country. For more information about the local APN, inquiry from your
local GPRS network operator.
6.12.1.2 Send SMS “#apn#password#APN content#APN user
name#APN password#” via a cell phone and if succeeded, the tracker
will return the message “set APN OK”.
E.g. send SMS command “#apn#123456#cmnet#”.
Notes: CMNET is the APN content of China Mobile (it has no APN user
name and password). If there is no APN user name and password, then no
need to write APN user name and password.
6.13 IP and Port setting
6.13.1 Send SMS “#IP#password#ip address#port number#”. If
succeeded, “set ip address and port ok” will be returned by SMS.
E.g, Send SMS command “#IP#password#116.205.4.114#8169#” to the
device (116.205.4.114 is IP, 8169 is port )
6.14 Cut oil or circuit (optional)
Send SMS “#stopoil#password#” to device, it will reply “stop oil
ok”, cut oil successfully.
Send SMS “#stopelec#password#” to device, it will reply “stop
electricity ok”, cut circuit successfully.
6.15 Recover oil or circuit
Send SMS “#supplyoil#password#” to device, it will reply “supply oil
ok”, recover oil successfully.
Send SMS “#supplyelec#password#” to device, it will reply “supply
electricity ok”, recover circuit successfully.
6.16 Power failure alarm (optional)
Built-in backup battery to realize power failure alarm, it will send SMS
“cut power alert!” to the authorized number.
6.17 Check device setting parameters
Send SMS “TCP” to device, device will reply SMS as below :
“ IP+port+APN+GPRS setting(A: GPS valid, V:GPS invalid)”
6.18 Web platform GPS tracking software
Web based platform www.secumore1818.com, Use IMEI login, default
password 123456.
Web platform features as below:
◆ Real time tracking
◆ History trace replay
◆ Platform disable oil or recover oil
◆ Multiple user fleet management
◆ Detect vehicle alarms and status
◆ Support Andriod & IOS APP tracking
7 Faults & Solution
Faults Solution
Its failed to read SIM card, need re-install SIM card; after inserting
yellow light flashing
SIM card, then turn on power
GPS not located, check if working outside not in room; install
blue light flashing
place has no metal cover
Lights will enter sleep after stable lighting on 5 minutes and not
Three light turn off effect GPS working, when calling device again will wake up
lights
Send SMS“TCP”check IP port is correct or not, GPS located
Can’t track online
show“A”, V means GPS not located.
Device has no reply Check if already existing admin number; SIM card has balance
Guarantee Card
User Name Phone
Address
Model No IMEI No
Purchase Date Invoice No
Seller Name
Address
Seller Contact
1.Within warranty period, if any damage caused by the product's own quality, user can br
purchasing invoice and warranty card to supplier to arrange repair.
2.Those machines that has refitted or added other functions by user own will not be acce
repair.
3.Attempt to disassemble the product can damage it and void your warranty.
4.This card and the purchasing invoice are both considered as a receipt for repair, please res
carefully.
