PRODUCT DATA SHEET
SikaBond® DV
Economical Water Resistant Bonding Agent And Mortar Admixture
DESCRIPTION
FEATURES
SikaBond® DV is a synthetic rubber emulsion that is
used as admixture for cementitious bonding bridges SikaBond® DV is simply added to the mixing water to
and high quality site-mix mortars. improve the following properties:
Suitable for use in hot and tropical climatic conditions. ▪ adhesion
▪ shrinkage
USES ▪ water resistance
▪ abrasion resistance
SikaBond® DV is used as bonding agent and site-mix ▪ chemical resistance
mortar admixture for the following applications: SikaBond® DV is non-corrosive, ready to use and does
▪ Thin layer patching mortars not re-emulsify, even under highly alkaline conditions.
▪ Renders
▪ Floor screeds CERTIFICATES AND TEST REPORTS
▪ Concrete repair mortars
▪ Abrasion resistant linings ▪ SikaBond® DV is certified according "Low Emitting
▪ Tile fixing mortars Materials as per Al Sa'fat - Dubai Green Building Eval-
▪ Masonry mortars uation System" by Dubai Central Laboratory (DCL)
▪ Bonding slurry for fresh to old concrete certificate No. CL17020432
▪ SikaBond® DV follows the requirements of ASTM
C1059 for Type II for bonding fresh to hardened con-
crete, when applied as a bonding slurry.
PRODUCT INFORMATION
Composition Styrene Butadiene Rubber
Packaging 20 L pails, 25 L pails and 200 L drums
Shelf life 12 months minimum from production date
Storage conditions Store in a dry area in original packaging and at temperatures between +5°C
and +35°C. Protect from direct sunlight, heat and moisture.
Appearance and colour White liquid
Density ~1.00 kg/l (+25°C)
Total chloride ion content Nil (EN 934-2)
Product Data Sheet
SikaBond® DV
March 2024, Version 04.02
020301010010000121
1/3
APPLICATION INFORMATION
Recommended dosage BONDING SLURRY FOR FRESH TO OLD CONCRETE:
SikaBond® DV : Ordinary Portland Cement (OPC) = 1 : 2
Note: Trial mixes must be performed to establish the exact dosage rate required.
For optimum results, always ensure that the correct SikaBond® DV : Water ratio is
used.
MORTARS AND RENDERS:
Trial mixes must be performed to establish the exact dosage rate required.
For optimum results, always ensure that the correct SikaBond® DV : Water
ratio is used. Depending on the application and performance required,
SikaBond® DV may be added to the clean mixing water within the range of
1:1 to 1:2. For all applications, apart from sprayed on renders, a bonding
bridge should be brushed into the prepared surface.
Mortar thickness Aggregate size
< 2 mm 0 - 0.5 mm
2 - 5 mm 0 - 1.0 mm
5 - 15 mm 0 - 3.0 mm
> 15 mm 0 - 7.0 mm
Note: The above mixes are for guidance only and based on the use of sharp, well
graded aggregates and dry sand.
BASIS OF PRODUCT DATA APPLICATION INSTRUCTIONS
All technical data stated in this Data Sheet are based SUBSTRATE QUALITY / PRE-TREATMENT
on laboratory tests. Actual measured data may vary
due to circumstances beyond our control. Concrete surfaces should be clean, sound, rough and
free from oil, grease, cement laitance and all loosely
IMPORTANT CONSIDERATIONS adhering particles. The surface should be in a satur-
ated surface dry condition (SSD).
▪ Never use pure SikaBond® DV or SikaBond® DV-wa- Rust, scale, dust and other loose and deleterious ma-
ter mix directly onto the substrate. Always mix with terials which reduces bond or contributes to corrosion
cement and aggregate (optionally, for mortars or shall be removed.
renders). MIXING
▪ The standard rules of good practice for production
and placing of bonding bridge, repair and adhesive BONDING SLURRY:
mortars must be observed when using SikaBond®
DV. Refer to relevant standards. Mix together with fresh cement to a homogeneous
▪ Fresh applied mortar must be cured properly espe- brushable slurry consistency. The resulting bonding
cially at high temperatures in order to prevent plastic slurry should be brushed well onto the prepared sur-
and drying shrinkage. Use Sika® Antisol® WB product face.
as a curing agent or apply curing by polyethylene MORTARS AND RENDERS:
sheet and wet hessian. Mixing can be done in any suitable concrete mixer,
▪ Higher dosages can be used depending on the mix
such as a pan mixer. First add the cement and aggreg-
design, raw materials, climatic conditions and mortar
ate into the mixer and mix to a uniform consistency.
requirements.
▪ Trial mixes must be performed to establish the exact Then add the required quantity of SikaBond® DV and
dosage rate required. mix slowly for at least 2 minutes. Apply by steel trowel
▪ We recommend to perform trial mixes to establish and finish with a wooden float.
the required performance when combining Sika-
Bond® DV with other products.
ECOLOGY, HEALTH AND SAFETY
User must read the most recent corresponding Safety
Data Sheets (SDS) before using any products. The SDS
provides information and advice on the safe handling,
storage and disposal of chemical products and con-
tains physical, ecological, toxicological and other
safety-related data.
Product Data Sheet
SikaBond® DV
March 2024, Version 04.02
020301010010000121
2/3
LOCAL RESTRICTIONS
Note that as a result of specific local regulations the
declared data and recommended uses for this product
may vary from country to country. Consult the local
Product Data Sheet for exact product data and uses.
LEGAL NOTES
The information, and, in particular, the recommenda-
tions relating to the application and end-use of Sika
products, are given in good faith based on Sika's cur-
rent knowledge and experience of the products when
properly stored, handled and applied under normal
conditions in accordance with Sika's recommenda-
tions. In practice, the differences in materials, sub-
strates and actual site conditions are such that no war-
ranty in respect of merchantability or of fitness for a
particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
mendations, or from any other advice offered. The
user of the product must test the product’s suitability
for the intended application and purpose. Sika re-
serves the right to change the properties of its
products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request.
Sika Gulf B.S.C. (c) Sika UAE LLC Sika Saudi Arabia Limited Sika LLC - Oman
Tel: +973 177 38188 Sika MB Construction Chemicals LLC Riyadh / Jeddah / Dammam / Rabigh Master Builders Solutions LLC
Email: info@bh.sika.com Sika International Chemicals LLC Tel: +966 11 217 6532 (part of Sika)
Sika Kuwait Cons. Mat. & Paints Co WLL Tel: +971 4 439 8200 Email: info@sa.sika.com Tel. +968 22 826 500
Tel: +965 22 282 296 Email: info@ae.sika.com Web: gcc.sika.com Email: info@om.sika.com
Email: sika.kuwait@kw.sika.com Web: gcc.sika.com Web: gcc.sika.com
Web: gcc.sika.com
SikaBondDV-en-AE-(03-2024)-4-2.pdf
Product Data Sheet
SikaBond® DV
March 2024, Version 04.02
020301010010000121
3/3
