WIDE MOUTH

SLOW JUICER

'LIFE TASTES GOOD' M6 WIDE MOUTH

A GLOBAL COMPANY
KUVINGS
MANUAL
• After you read this manual,
keep in the place you can reach easily.
• The color of product may vary.
• Household use only.
B77.JM6.ⓜ.1-131014M

Downloaded from www.Manualslib.com manuals search engine

 IMPORTANT SAFEGARDS

When using electrical appliances, basic safety precautions should always be followed
including the following:

1. Read all instructions.

2. To protect against risk of electrical shock do not put motor or base of unit in water or other liquid.
3. Close supervision is necessary when any appliance is used by or near children.
4. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Return appliance to the nearest authorized service facility for examination,
repair or electrical or mechanical adjustment.

CONTENTS 7.
8.
9.
The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.
Do not use outdoors.
Do not let cord hang over edge of table or counter.
10. Always make sure juicer cover is clamped securely in place before motor is turned on. Do not unfasten clamps
03 Important Safeguards while juicer is in operation.
11. Be sure to turn switch to OFF position after each use of your juicer. Make sure the motor stops completely
04 Safety Warning before disassembling.
12. Do not put your fingers or other objects into the juicer opening while it is in operation. If food becomes lodged
06 Parts in opening, use food pusher or another piece of fruit or vegetable to push it down. When this method is not
08 How to Assemble possible turn the motor off and disassemble juicer to remove the remaining food.
13. Do not use the appliance if the rotating sieve is damaged.
10 How to Operate 14. When a separable pulp container is provided, Do not operate without the pulp container in place.
12 Tips on Operation 15. Please do not alter the appliance in anyway.
16. Do not use the appliance for anything other than its intended purpose as described in the manual.
13 Tips on Ingredient 17. The appliance should be used for limited period of time.
14 Ingredients Preparation
18 How to Disassemble and Clean
20 How to Clean Silicone Parts
ㆍThis appliance is for household use only. Please carefully follow the instructions in the manual.
21 How to Use the Cleaning Tool (The appliance cannot be covered under the manufacture warranty if the product is abnormally or commercially used.)
ㆍSave the instruction manual for future reference
22 OPTIONAL | How to Use the Mincer ㆍIf the appliance is given away as a gift, please include the manual with the product.
24 OPTIONAL | How to Use the Blank Strainer
26 OPTIONAL | How to Use the smoothie strainer
The following precaution is provided to ensure the safety of the user. Please carefully read through the pre-
28 Troubleshooting Q&A cautions and exercise a degree of care when using the appliance.
30 Specifications Warning : Warns risk of death of severe injuries.
Caution : Warns risk of injuries or appliance damage.

Read all Instructions Before Use Prohibited

Follow instruction
Unplug from the outlet

Do not disassemble
Must take action

Be cautious of electric shock

Downloaded from www.Manualslib.com manuals search engine

 SAFETY WARNING SAFETY WARNING

Do not plug multiple power cords on a single outlet during operation. Do not put the parts in the dishwasher or extremely hot water.
→ It may cause and explosion or fire. →The parts may wear faster.

Do not touch the power cord with wet hands. Do not repair, disassemble the base, or customize the appliance.
→ It may cause electrical shock. → The appliance may not operate properly causing fire, electrical shock, or injury.

Do not use the appliance on an uneven surface.

Do not leave the appliance unattended. Unplug the power cord from the →It may cause a malfunction if the appliance tips over.
outlet when not in use.

Keep away from children and store the appliance in a safe place.
Use a dry towel to clean the power cord if it is dirty or wet. →If may cause injury.
→It may cause electrical shock or file

Please do not store or operate the appliance nearby heating appliance.

→ The appliance may become discolored or deformed.
Do not drop the appliance nor inflict strong force to the appliance.
→It may damage or break the appliance.
Do not use any hazardous chemicals to clean the appliance or spray flam-
mable sprays near the appliance.
→It may change the color of the appliance or could result in a fire.
Do not unplug by pulling off the power cord cable.
→It may damage the power cord and cause electrical shock.
To protect the power cord, please do not aggressively bend or put heavy
object on top of the power cord.
→It may cause short circuit or even fire.

Do not put your finger or other objects into the feeding tube while it is in
operation. Operating the juicer without ingredients can cause damage to the screw.
→If may cause injury.

4 5

Downloaded from www.Manualslib.com manuals search engine

 PARTS
* The products illustrated/photographed in this booklet may vary slightly from the actual product.

Pusher
Align
1. Feeding Tube
5. Smart Cap
Detachable +

2. Drum Lid Align the dots ● and slide

the pusher in.

3. Juicing Bowl 6. Base +

STEP 1
Top-set Assembly

Align the red dots ● on each part and

assemble in the order shown. Once
+ assembled, turn the drum lid clockwise
to close.
4. Pulp Cup 7. Juice Cup

8. Rotation Wiper 9. Strainer 10. Juicing Screw

+
STEP 2
Top-set and base assembly

Place the drum lid on the juicing bowl.

Align the down arrow ▼on the drum lid
11. Pusher 12. Cleaning Brush 13. Rotating Brush + with the OPEN mark on the base and
turn to the CLOSE position.

6 7

Downloaded from www.Manualslib.com manuals search engine

 HOW TO ASSEMBLE

STEP 1 Top-set Assembly STEP 2 Top-set and Base Assembly

For easy assembly hold the drum lid
Check Before • Wash the parts before first use. TIP by grabbing the feeding tube and turn 6 Open/Close mark on the top-set.
Operating • Ensure that the compression silicone and silicone ring are assembled properly. clockwise as shown in the illustration.

Firmly insert the compression silicone Place the juicing screw into the strainer.
1 into the slot below the pulp spout. 3 Turn and press down on it until it clicks
into place.

Open

Note | The Juicer may leak if not assembled Note | The juicing screw needs to be locked in
properly. place in order to close the drum lid.
Close

Assemble the strainer into the rotation Place the drum lid on to the juicing bowl
2 wiper then place this assembly in to the 4 aligning the red dot ● on the drum lid
Note | Juicer will not operate if parts are not
assembled properly.
juicing bowl ensuring the red dot ● on with the red dot ● on the juicing bowl.
the strainer is aligned with the red dot ● Turn clockwise to close, aligning the red
on the juicing bowl. dot ● on the drum lid with the close
mark . 5 Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
7 Place the pulp cup under the pulp
spout and place the juice cup under the
lid with the OPEN mark on the base juice spout as shown in the illustration.
and turn to the CLOSE position.

Detachable

8 9

Downloaded from www.Manualslib.com manuals search engine

 HOW TO OPERATE

STEP 1 After preparing the ingredients, plug the power cord into a wall outlet. STEP 3 Insert the prepared ingredients one piece at a time.
Note | • Fibrous leafy vegetables (celery, kale, etc.):
Note | • Do not touch the power cord with wet hands. It may cause electrical shock,
short-circuit, or fire. » Separate each stem. Cut the outer stems that are thick and tough to 4 inches long or
less.
• Check the safety of the wall outlet. » Bundle up the leafy vegetables as inserting into the juicer. Alternate between leafy
parts and stems.
• Before extracting, remove hard seeds or pits in ingredients.
STEP 2 Press the FORWARD button to operate. • When juicing frozen fruits with small seeds, ensure that even the seeds are completely
thawed.
Note | • Forward: Pulls down and slowly masticates the ingredients. • Insert the ingredients one piece at a time.
• Reverse: Pushes the ingredients back up to dislodge them. Tip | • Align the dots ● and slide the pusher in.
• After inserting ingredients, use the pusher when it is necessary. Too much use of the
If the ingredients become jammed in the screw and the drum lid does not open, press the OFF pusher may affect the juice quality.
button. Then press and hold the REVERSE button until the ingredients become dislodged.
» Intermittently use the pusher for soft ingredients like tomatoes and apples. Constant
Repeat REVERSE - OFF - FORWARD as often as needed to achieve the desired result.
use of pusher for soft ingredients may affect the juice quality.

STEP 4 Use the smart cap to make mixed juices,

stop juice from dripping, or rinse between
If the juicer stops during operation: different juices.
Smart cap
Tip | • Juicing with the smart cap closed creates various mixed juice creations when
Switch the button to OFF position then press and FORWARD : Pulls down the food different fruits and vegetables, milk, banana, beans etc. are selected.
hold the REVERSE button until the ingredients OFF : Stops the operation
become dislodged. • After juicing, close the smart cap to stop the juice from dripping, especially when
REVERSE : Pushes the food back up
Repeat REVERSE - OFF - FORWARD as needed. disassembling the juicing bowl off the base.
• When making different juices quickly rinse away any leftover flavors by running a
glass of water in the juicer with the smart cap closed.
Note | • Leave the smart cap open when juicing ingredients that create excessive foam
during extraction, (e.g. apples, celery).
2 4
• Pay close attention when operating with the smart cap closed. Juice may overflow
1 3
if the juice collected in the juicing bowl exceeds its capacity marked on the bowl.

OFF ▶ REVERSE ▶ OFF ▶ FORWARD STEP 5 After juice and pulp are completely extracted, switch the unit OFF.
Note | • If the remaining ingredients in the juicing bowl have not been extracted
Note | • REVERSE: Pushes the ingredients back up to dislodge them. completely, the drum lid may not open easily. After each extraction, run the juicer
The REVERSE button only works while holding down the switch. for an additional 30 seconds to let the juicer extract the remaining pulp.
• Switch OFF ensuring that the juicer comes to a complete stop. Then press REVERSE. • When the drum lid is stuck, press the REVERSE - OFF - FORWARD button in this
Hold the REVERSE button for 2-3 seconds and release. Repeat as needed. Let the order; switching back and forth 2 or 3 times to dislodge the ingredients. Then
juicer stop completely before using the REVERSE button to prevent malfunction. place hands on top of the drum lid and firmly press down while simultaneously
• If the juicer does not work after these steps, disassemble and clean the parts turning the drum lid counter clockwise to open.
before operating the juicer again. » Depending on the ingredients, pour water down the feeding tube to rinse out
the interior of the juicing bowl and then attempt to remove the drum lid.

10 11

Downloaded from www.Manualslib.com manuals search engine

 TIPS ON OPERATION TIPS ON INGREDIENTS

1. Operating the juicer without ingredients can cause damage to the screw. Juicer damage due to owner negligence or from not following the instructions in the owner’s manual will void
the warranty service.
2. Do not continuously operate the juicer for more than 30 minutes.
This can damage the motor from overheating.
After continuous use, let the juicer rest for 30 minutes to cool down before starting another DO NOT put the following ingredients into the juicer:
session.
3. Do not put fingers or other objects into the feeding tube. Always use provided
Peach, nectarines, apricot, plum, mango, etc.
pusher when needed. Hard seeds Remove hard seeds from the ingredients
If other objects are inserted into the feeding tube during operation, such materials can get stuck
before juicing.
and damage the juicer parts and/or cause injury.
4. Do not put dried or hard ingredients like whole grains, fruits with hard seeds or ice
Hard or Pineapple, melon, mango, orange, etc.
into the juicer. inedible
These may damage the juicer parts (e.g. juicing bowl, juicing screw, and strainer). Peel the skins from the ingredients before juicing.
skins
• Beans or grains can be used if soaked overnight or boiled.
• Fruits with pits and hard seeds (e.g. nectarines, peaches, mangoes and cherries) must be pitted Frozen strawberry, blueberry, raspberry, etc.
Frozen
before juicing. Completely thaw frozen fruits before juicing.
fruits or ice
Do not use ice.
• When using frozen fruits with small seeds such as grapes, completely thaw before inserting
them into the juicer.
Sesame seed, butter, margarine, etc.
5. Do not use ingredients containing excessive amounts of vegetable oil or animal fat. Vegetable/ Do not extract ingredients containing vegetable
Do not use the juicer to extract vegetable oil from ingredients. animal oil or animal oil. This can reduce performance and
If vegetable/animal oil gets on the juicing screw, it may reduce performance and even damage even damage the juicer.
the part.
6. Do not reinsert the extracted pulp into the juicer. This can cause the juicer to stop or Coconut, sugarcane, whole grains, etc.
Others Do not extract ingredients with no water
cause the drum lid not to open.
content.
7. After juicing ingredients with seeds like grapes, thoroughly clean all the crevices on
the bottom of the juicing screw.

Experience the best quality juice by understanding each ingredient’s characteristics

and knowing the optimal way of handling the ingredients.

The Slow Juicer is an innovative product that uses a patented slow-

speed masticating technology to efficiently extract the juice from
ingredients. The juicer is designed to obtain the best result from
ingredients with firm composition and with high water content.
For best result, each ingredient should be prepared and extracted
depending on its characteristics and properties.

12 13

Downloaded from www.Manualslib.com manuals search engine

 INGREDIENTS PREPARATION

Before • Before Operating: If the juicer is jammed or if the drum lid does not open, How to Use • Juicing with the smart cap closed allows mixed juice creations with different
Operating: press the REVERSE button and hold until it becomes dislodged. the Smart fruits, vegetables and liquids.
Repeat REVERSE-OFF-FORWARD as needed. Cap: • After juicing, close the smart cap to block excess juice from dripping,
• Continue operating the juicer until all the ingredients in the juicing bowl are especially when disassembling the juicing bowl off the base.
extracted. The drum lid may not open easily if there is a lot of pulp remaining • When making different juices quickly rinse away any leftover flavors by
in the juicer. running a glass of water in the juicer with the smart cap closed.
• Every ingredient yields different amounts of juice. • Leave the smart cap open when juicing ingredients that create excessive
foam during extraction (e.g. apples, celery).
• Pay close attention when operating the juicer with the smart cap closed. Juice
Juice Yield: • For the optimal extraction and maximum juice yield, cut the ingredients may overflow if the juice collected in the juicing bowl exceeds its capacity
following the guidelines given in this section. marked on the juicing bowl.
• Insert ingredients slowly monitoring how the ingredients are extracted.
The juice yield may vary depending on the juicing speed.
Adjusting • Depending on the ingredient, you may get extra pulp in the juice when
the amount juicing continuously.
of pulp in • To reduce the amount of pulp, disassemble the top-set and wash frequently.
Soft fruits and vegetables (e.g. oranges, tomatoes):
| (E.g. apples, oranges & tomatoes)
the juice:

Hard fruits and vegetables (e.g. carrots, potato, beets & spinach):
1-4 wedges

- Peel the skin off oranges, and for tomatoes and

apples, take out the stem.
- If the ingredients are larger than the feeding 1/2 - 1 inch
tube, cut the ingredients into pieces that will fit into 6 inch
the feeding tube.
- Fruits with seeds must be pitted before extraction.
Cut to 1-4 wedges then slowly insert the ingredients 1 inch
down the feeding tube.
Hard fruits and Soak in cold water To increase the juice
PREPARATION TIPS:
vegetables may put prior to juicing and yield, juice fruits and
• Cut 1-4 wedges. excess strain onto the cut to appropriate vegetables with high
motor and cause it to sizes. water content.
EXTRACTION TIPS: stall.
• Slowly insert the ingredients one piece at a time.
• Use the pusher to push the ingredients down the feeding tube. (The pusher also helps prevent juice
from spraying out of the feeding tube when extracting ingredients with high water content) PREPARATION TIPS:
• Leave the smart cap open when juicing ingredients that create excessive foam during extraction. • Slice the ingredients 1 inch thick or cut 1 inch wide and 2-6 inches long.
(Foam can accumulate if operated with the smart cap closed. ) • Soak hard ingredient like carrots and ginger in cold water prior to juicing.
• It is recommended that the extracted juice be consumed within 48 hours after extracting. Depending EXTRACTION TIPS:
on the density of the ingredients the extracted juice can gradually show layers over time.
• Slowly insert the ingredients one at a time.
• If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.
• Pace the juicing speed ensuring each ingredient is thoroughly extracted.
• When an ingredient is being masticated by the juicing screw, the squeezed ingredient may splash juice
through the feeding tube. Use the pusher to block out the juice splash when juicing • To maximize the juice yield, juice with ingredients with high water content.

14 15

Downloaded from www.Manualslib.com manuals search engine

 INGREDIENTS PREPARATION

Ingredients with small seeds (e.g. raspberry, pomegranate, grape):

| (E.g. apples, oranges & tomatoes)
Fibrous and/or tough leafy ingredients (e.g. celery, kale, pineapple):
| (E.g. apples, oranges & tomatoes)
Slowly insert ingredients with small seeds to prevent the seeds from clogging the strainer. Fibrous ingredients like celery and kale should be cut into small lengths before juicing

4 inches

Insert ingredients slowly For best result, juice with When juicing leafy If leafy ingredients It’s best to juice with
to minimize the amount ingredients with higher ingredients like celery and wrap around the ingredients with higher
of leftover seeds in the amount of fluid(e.g. apple, kale, do not collect more juicing screw, open amount of fluid, like
strainer. pear) than 500g per session. For the lid and remove apples or carrots.
best result, disassemble the fibers before
Carrots, apples : fibrous
and wash the top-set continue juicing.
ingredients = 9:1
before juicing again.
[recommended ratio]

PREPARATION TIPS: PREPARATION TIPS:

• When juicing frozen ingredients(e.g. raspberry, strawberry), make sure they are completely thawed. • Soak fibrous ingredients in cold water for about 30 minutes before cutting them.
• Thoroughly rinse ingredients like grapes. Take the grapes off and discard the stem. • Separate each stem. Cut the outer stems that are thick and tough to 4 inches lon g or less.
• For pomegranate, discard the skin and juice only the inner part EXTRACTION TIPS:
EXTRACTION TIPS: • One at a time, slowly insert the prepared ingredients.
• Depending on the size of the grape, insert 3~5 grapes at a time while monitoring the extraction result. • Insert more ingredients after the previously inserted ingredients have been completely extracted.
• Thaw frozen ingredients like pomegranate and raspberry then insert about 1 tablespoon (5g) at a time. ① Roll leaves in spiral as inserting into the juicer.
• Frozen ingredients usually lose significant amount of fluid from thawing. When juicing, mix milk or ② Insert the leafy part of the ingredients first then alternate between leafy parts and stems.
yogurt to balance the fluid lost. ③ For ingredients like wheatgrass, grab a handful and insert in a bundle.

Caution | • The fibers from tough ingredients like celery can wrap around the juicing screw and affect
juicer’s performance. Cut the stems that are thick and tough to 4 inches long or less.
• Foam can build up from juicing fibrous ingredients. Use strainer to remove the foam before
Caution | If the lid does not open due to excessive amount of small seeds left in the juicing bowl, serving.
continuously run the juicer for 30 second to extract any leftover seeds. If the lid is still stuck, repeat • For ingredients like pineapple, slice off the rind of the pineapple and cut around the fibrous
REVERSE - OFF- FORWARD until the ingredients become dislodged. Then twist the lid to open while core. Cut the flesh of the pineapple to smaller pieces.
pushing downwards on the lid with palms(depending on the ingredient, pour some water down
• Recommended amount of juicing per session is 500g. When juicing more than 500g, wash the
the feeding tube for quick rinsing to help dislodging). top-set before continue juicing.

16 17

Downloaded from www.Manualslib.com manuals search engine

 HOW TO DISASSEMBLE AND CLEAN
* The products illustrated/photographed in this booklet may vary slightly from the actual product.

1
1 Switch OFF and unplug the power cord 4 Remove the juicing screw, strainer and
6 Under running water, clean the outside Quick Rinsing
from the wall outlet. rotation wiper unit from the juicing bowl. of the juicing screw with a dish scrub. Use
Clean with provided brush. the tip of the cleaning brush to push out With the smart cap closed, fill the
Note | • Extract all the remaining pulp in the
juicing bowl before stopping the juicer. any residue in the crevices on the bottom 1 juicing bowl with water and turn on
of the juicing screw. the juicer.
• For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
• When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in
this order, switching back and forth 2 to
3 times to dislodge. Then place hands
on top of the drum lid and firmly press
down simultaneously turning the drum
lid counter clockwise to open.

Turn the drum lid counter clockwise to

2 open.
Note | • Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean- Tip | • Thoroughly clean the juicing screw
up difficult. The excess build up can cause ensuring that the juicing screw is clean
poor performance in future uses. without any residue.
• For easier disassembly, place the top- • Completely dry before using. Let it run for a moment. Open the
set in the sink and run the water through
from the top of the top-set.
Note | • After juicing ingredients with seeds, make 2 smart cap and let the water run out
sure to thoroughly clean the bottom of the juicing bowl.
• Thoroughly dry the bottom of the juicing crevice of the juicing screw. If this area
screw where it connects to the metal isn’t properly cleaned, it can affect the
cylinder shaft on the base. balance between the juicing screw and
the strainer and damage the parts.

Place the juicing bowl under running Clean the base with a soft damp towel
Note | • When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
5 water and unplug the compression 7 and dry.
the appliance by grabbing the base or silicone to clean the pulp spout.
handle.

Turn the top-set counter clockwise and

3 lift off the base.

Tip | • It is not necessary to completely

clean the juicer in between making
multiple juices during a single juicing
session.
• When finished with juicing, always
disassemble and clean thoroughly
Tip | • Soak the juicing bowl in a solution of Note | • If the towel is dripping wet, make sure between juicing sessions to prevent
warm water with baking soda or little bit to squeeze out the excess liquid before residue buildup.
of bleach to clean the excess build up. using it on the juicer.

18 19

Downloaded from www.Manualslib.com manuals search engine

 HOW TO CLEAN SILICONE PARTS HOW TO USE THE CLEANING TOOL
* The products illustrated/photographed in this booklet may vary slightly from the actual product.

Tip | Clean the rotation wiper under running water. Tip | The cleaning tool makes clean-up quick and easy.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the compression Completely dry after cleaning.
silicone and silicone ring are firmly inserted.
Note | Use the included cleaning brush to remove hard to reach bits after using the cleaning tool.
Note | If the compression silicone and silicone ring are not firmly inserted, juice may leak from the
bottom of the juicing bowl.

Silicone Brush 1
1 Hold the cleaning tool with one hand and insert
Pull out the silicone brush from the strainer into the cleaning tool.
the rotation wiper to clean. Note | Insert the strainer until you hear a click.
After cleaning, insert into the slot
with the tail pointing down as
shown in the illustration.

Compression Silicone Under running water, rotate the cleaning

Unplug to clean.
2 tool and the strainer in opposite directions to
After cleaning, firmly insert into clean.
the slot below the pulp spout.

Silicone Ring Thoroughly rinse the inside and outside of

3 the strainer under running water.
Remove the silicone ring from the
juicing bowl to clean.
After cleaning, push in the silicone
ring with the smaller surface facing
down.

Smart Cap After cleaning, remove the strainer from the

Remove from the juice spout
4 cleaning tool. Dry before storing.
to clean.
After cleaning, attach the smart
cap to the smart cap silicone on
the juice spout.

20 21

Downloaded from www.Manualslib.com manuals search engine

 OPTIONAL | HOW TO USE THE MINCER
* Dissemble is opposite of Assemble.

1
1 Insert screw in the Mincer Bowl and close with 1
3 Switch the lever side to side to adjust for different ingredients.
Mincer lid. Lid
Lever Position 1
① Insert and push down the juicing screw into the Chopping into small pieces
work bowl
Lever Position 2
② Align the dots ●on the lid and the work bowl.
Chopping into bigger pieces (Moist ingredients) Lever
While the dots ●are aligned, place the lid on the Juicing Screw
work bowl to combine the parts. *same part from
Solw juicer
③ After the lid has been correctly placed on the work
bowl, twist the lid clockwise until it locks onto the Disassembling the lever unit:
work bowl. (Align symbol with●symbol)
Work Bowl
1. Place the lever in between position 1 and 2 to be
vertically upright.
2. Slide the lever unit down by pressing from the top,
then remove the lever unit by pushing inwards.

Tip | • The lever unit can be disassembled for cleaning.

• After washing, please dry the lever before reassembly.
• Before using, make sure the lever is in the 1 or 2
position ‫⯹݌‬
(depending on the ingredients used).
ᩕฝ

1
2 Place the Mincer onto the base CAUTION

• Only use the pusher when pushing ingredients in.

• Do not adjust the lever during operation.
• While operating, do not try to pull ingredients out with fingers, utensils, etc.
• Hard vegetables or fruits like carrots should be cut into small pieces and fed slowly.
MINCER
• Do not use hard nuts, seeds, ice, frozen fruits. Frozen fruits must be completely thawed
and pitted before using.
• It may cause a malfunction if grains(beans, rice, etc.) are not boiled or soaked overnight
before using.
• When using fish or meat, completely remove the bones, tendons, fat, skin from the
ingredient before using.
Base Place the lid on the work bowl. Align the down • Leafy vegetables(scallions, chives, etc.) are not suitable for this product.
arrow ▼ on the lid with the OPEN mark on
the base and turn to the CLOSE position.

22 23
‫⯹݌‬
ᩕฝ

Downloaded from www.Manualslib.com manuals search engine

 OPTIONAL | HOW TO USE THE BLANK STRAINER
* Dissemble is opposite of Assemble.

Before use, make sure the silicone cover is correctly in place.

1
1 To assemble the top set, place the juicing screw
CAUTION
and the blank strainer in the juicing bowl and
close the lid. Lid
The blank strainer is used only with frozen ingredients. Depending on the different
ingredients, allow the frozen items to thaw for 5 to 20 minutes before use. Slowly
① Insert the blank strainer into the juicing bowl
while aligning the red dots ● of the blank strainer
process a smaller amount per batch.
and the juicing bowl.
Juicing Screw
② Insert the juicing screw into the blank strainer * use the same
with a twisting motion. juicing screw from
the Solw Juicer
③ Place the lid onto the juicing bowl by aligning the
red dots ● of the lid and the juicing bowl. Then,
rotate the lid clockwise until the lid is secured. Blank Strainer

※ Do not use ice or process ingredients containing vegetable or animal oil.

When using the blank strainer, It may cause a malfunction.
always leave the Smart Cap open. ※ Remove hard seeds from the ingredients and peel the skins from the ingredients
Juicing Bowl before juicing.

1
2 Place the assembled top set onto the base.

HOW TO CLEAN THE SILICONE COVER

Top Set
The silicone cover is removable for cleaning.
After cleaning, place the silicone cover on
as shown in the picture.

TIP | Carefully place the silicone cover

by aligning grooves and wedges.
Align the arrow ▼ from the lid with the
Base OPEN sign from the base and rotate the
topset clockwise until the arrow ▼ from
the lid is in CLOSE position.

24 25

Downloaded from www.Manualslib.com manuals search engine

 OPTIONAL | HOW TO USE THE SMOOTHIE STRAINER
* Dissemble is opposite of Assemble.

CAUTION
1
1 To assemble the top set, place the juicing screw and
Lid
the smoothie strainer in the juicing bowl and close When using frozen ingredients, make sure to thaw your frozen ingredients for about 5 to
the lid. 20 minutes before use.
① Insert the rotation wiper and the smoothie strain- (The required period to thaw the ingredients will depend on how long the ingredients were
er into the juicing bowl while aligning the red in the freezer and the temperature it was kept in.)
dots ● of the smoothie strainer and the juicing
bowl. Juicing Screw
② * use the same
Insert the juicing screw into the smoothie strainer juicing screw from
with a twisting motion. the Solw Juicer
③ Place the lid onto the juicing bowl by aligning the
red dots ● of the lid and the juicing bowl. Then, Smoothie
rotate the lid clockwise until the lid is secured. Strainer
When making smoothie, add milk or other types of liquid between ingredients.
when using the smoothie strainer, make sure the Check the consistency of the smoothie by looking through the juicing bowl, and add more liquid as needed.
smart cap is closed to make the better smoothie. Rotation Wiper
※ Please do not insert ingredients like ice, meat, oil or fat based ingredients.
These ingredients may damage the components.
Juicing Bowl ※ Please remove hard or thick seeds, pits, or peel before use.

1
2 Place the assembled top set onto the base.

HOW TO CLEAN THE SILICONE WIPERS

The silicone wipers are removable for cleaning. After cleaning, place the silicone wipers back
onto the frame as shown in the picture.
Top Set

Align the arrow ▼ from the lid with the

Base OPEN sign from the base and rotate the Tail
topset clockwise until the arrow ▼ from
the lid is in CLOSE position.
TIP | Insert into the slot with the tail pointing down.

26 27

Downloaded from www.Manualslib.com manuals search engine

 TROUBLESHOOTING Q&A

When there is no power to the juicer: The drum lid will not close: During juicing, the juicer stopped: Is it possible to juice ingredients with
• Check if the power cord is properly plugged in. • Make sure the juicing screw is pushed all the • Check the power cord and make sure it is tough fiber?
• Check if the drum lid and the juicing bowl are way in to the strainer in order for the drum lid plugged in correctly. • Ingredients like celery or ginger contain long
properly assembled. to close properly. • Check that all the parts are correctly assembled. fibers that may wrap around the juicing screw
• Check if the top-set and the base are properly • If the juicing screw is not properly in position, • If too many ingredients are inserted at one and affect the juicer’s performance. When
assembled. the drum lid may not close. time, this can cause the juicer to stop. juicing fibrous ingredients, do not collect more
• Juicer will not operate if parts are not • When the juicer stops because there are too than 1 lb. of juice. After collecting this quantity
assembled properly. many ingredients inserted in it, press the or less, clean the top-set completely before
Odd noise from the juicer:
REVERSE - OFF - FORWARD button in this order, juicing again.
• Check if the parts are assembled correctly.
Low juice yield: Try reassembling the parts and listen for the switching back and forth 2 to 3 times.
odd noise. • The reverse setting will push the ingredients Discoloration of the plastic parts:
• Different ingredients hold different amounts of
• Do not start the juicer unless there are up, and the forward setting will pull the • After juicing, if the juicer is not cleaned right
fluid that will yield different amounts of juice.
ingredients and/or liquid in it. ingredients down. away, the remaining pulp inside the top-set
• If the ingredients are not fresh, they may
• Operating the juicer without ingredients can • If the juicer stops due to the overload can dry up which can make disassembling and
contain reduced amounts of fluid, which will
cause damage to the screw. protection, let the juicer cool for 30 minutes to cleaning hard. This can also affect the juicer’s
yield less juice.
• If the juicer is operated without ingredients or 2 hours before juicing again. performance and color.
• Check if the compression silicone is firmly
liquid, the noise level can increase and also can • If there are hard seeds within the ingredients, • Ingredients that are rich in carotenoids such
inserted.
lead to damage. remove them before juicing. Hard seeds can as carrots and spinach may dye plastic parts.
• If the ingredient itself has low water content, it damage the juicer. When the parts are dyed with carotenoids, rub
may help to soak it in water before juicing. • The friction noise from the juicing screw and
the strainer will disappear when ingredients vegetable oil in to the dyed areas and use mild
• If juicing ingredients with small seeds, after a detergent to clean.
few servings, it may reduce the juice yield. For are inserted into the juicer. Layers of separation in the juice:
• If the noise occurs when ingredients are • Vegetable oil should only be used during
best result, disassemble and wash the top-set • Depending on the density of the ingredients,
inserted into the juicer, check the size of the clean-up for parts that are discolored. Do not
in between juicing. the extracted juice may show layers of different
ingredients. Do not insert anything over 1 inch use vegetable oil on the juicing screw or the
• If there is seed residue on the bottom of the juices. It is different from separation due to
in thickness. strainer. If vegetable oil or oil from animal fat
strainer, this can affect juicer performance and oxidation caused by juicing with a high-speed
gets on the juicing screw or the strainer, this
the overall juice yield. • Depending on the type of ingredients, the juicer. can affect the juicer’s performance and may
dimensions can be smaller.
result in damaged parts.
• The noise can occur if the juicer is operated on The drum lid is stuck:
There is too much pulp in the juice: • The silicone pieces on the top-set can be
an uneven or slanted surface. Place the juicer
• When continuously juicing, and depending on • After juicing, let the juicer operate for another detached to be thoroughly cleaned.
on a horizontally flat surface when operating.
the ingredient, the juice may contain a lot of 30 seconds to extract the remaining pulp.
fine pulp. • If there is too much pulp in the top-set, this Using for purposes other than juicing:
The extracted pulp is very moist: can cause the drum lid to not open. In this
• To reduce the fine pulp, clean the top-set • This juicer is designed to juice ingredients like
frequently and extract the pulp. • During the very beginning of extraction, the situation, press the REVERSE OFF - FORWARD
fruits and vegetables.
• Use a mesh strainer and put the juice through pulp can be more moist. button in this order, switching back and forth 2
to 3 times. • Do not use the juicer for extracting vegetable oil.
it to collect the unwanted pulp. • Depending on the ingredient’s condition, the
extracted pulp can be affected; especially • Pour water down the feeding tube to rinse out • Do not juice ingredients with high contents of
• If the strainer and the screw are damaged vegetable/ animal oil.
and affecting the juicer’s performance, it is when the ingredient is not fresh, the juice can the insides and then try opening the drum lid.
be extracted with the pulp. • If vegetable/animal oil gets on the juicing
recommended the parts be replaced. screw or the strainer, this can affect the
*The lifetime of each part may vary depending Juice dripping down the body of the base: performance of the juicer and could result in
on length and method of use and ingredients During operation, the juicing bowl shakes. • If the compression silicone on the bottom of damaged parts.
extracted. • The juicing screw and the strainer are set up to the juicing bowl is not plugged in correctly, the
• If too many ingredients are inserted at the crush and squeeze the ingredients. It is normal juice may seep out on to the juicer base. Before
same time, it may cause the juicer to stop for the juicing screw and the strainer to vibrate. assembling the parts, check and make sure the
frequently. This can lead to pulpy juice. Insert • If the ingredient contains strong fiber, the compression silicone is plugged in correctly.
the ingredients slowly and few at a time. vibration from the top-set may be stronger.

28 29

Downloaded from www.Manualslib.com manuals search engine

 SPECIFICATIONS

Product Juicer

Model NS-621CBS2

Voltage AC220-240V, 50/60Hz

Power Consumption 240W

Maximum Use Less than 30 min

Weight 6.4kg
Dimension 228 x 208 x 449 (mm)
Manufacturer NUC Electronics Co., Ltd.
Type Low speed compression

30

Downloaded from www.Manualslib.com manuals search engine