Scribd
Upload
12 views2 pages

E Track 4G

The document provides detailed specifications and pin diagrams for the POWERAMR IoT Gateway, including power requirements, CPU, memory, modem capabilities, and I/O ports. It also outlines LED status indicators for device operation and SIM card installation instructions. The product features surge protection, various communication protocols, and is designed for a wide operating temperature range.

Uploaded by

aaquib
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
12 views2 pages

E Track 4G

The document provides detailed specifications and pin diagrams for the POWERAMR IoT Gateway, including power requirements, CPU, memory, modem capabilities, and I/O ports. It also outlines LED status indicators for device operation and SIM card installation instructions. The product features surge protection, various communication protocols, and is designed for a wide operating temperature range.

Uploaded by

aaquib
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

POWERAMR IOT GATEW AY CONNECTION

PIN DIAGRAM
Pin No. Pin Name Description
1 +12V DC IN - Input voltage: 9V~30V/1A.
2 GND Ground Pin
3 D+ RS485 Data+
4 D- RS485 Data-
5 DI-1 Digital Input / 0 TO 5 V INPUT
6 DI-2 Digital Input / 0 TO 5 V INPUT
7 AI+ Signal FOR 4- 20 M AMP
8 AI- Common Loop- No Connection

Specifications- E Track 4G

CPU ARM Cortex

SRAM 64 Kbytes

System Flash Memory 256 Kbytes

Data Log Flash Memory 64MB (17000 Records Offline)

WDT(watchdog) Yes

RTC Onboard RTC

Protection 2 KV Surge Protection on RS 485

Modem LTE LTE FDD: Max 150Mbps (DL)/Max 50Mbps (UL)


LTE TDD: Max 130Mbps (DL)/Max 30Mbps (UL)

GPRS/Edge EDGE: Max 296Kbps (DL)/Max 236.8Kbps (UL)


GPRS: Max 107Kbps (DL)/Max 85.6Kbps (UL)

Serial ports RS232 Utility port RS-232: TxD, RxD, GND (use for device configuration and debug)

RS485 RS-485: D+, D- (use for communication with other devices)

Slaves Maximum 8 Nos of Slave can be connected

Baud Rate Supports 2400,4800,9600,19200,38400,57600,115200

I/O Port Analog Inputs 2 Nos of ( 0-5 V) and 1 No Analog Port ( 4-20 m amp)

Protocol Transmit Protocol TCP/ HTTP/ MQTT/SSL

Power Operating Voltage 12VDC to 24VDC

Mechanical Casing Plastic Casing

Dimensions (W x L x H) 85mm x 100mm x 30mm

Environmental Operating Temperature -25 C +55 C

Ambient Relative Humidity 5 ~ 95% RH, non-condensing

Certification CE SIEMIC CE2200


LED Status
LED NAME DESCRIPTION
GREEN POWER Light when Power on the device
LED Status Connection State

Flashing (ON for 100ms and OFF for SIM Card not found
100ms)

Flashing (ON for 500ms and OFF for Searching for GSM Network
500ms)
RED GSM
Flashing (ON for 0.1s and OFF for
2.9s) Once at every 3sec GSM Network Registered

Flashing twice at every 3sec GPRS IP Connected

Flashing 5times GPRS IP Sending data

LED OFF GSM Fault


GREEN COM TX Blink on data transmission in RS485 port
YELLOW COM RX Blink on data reception in RS485 port

SIM Card Installation

Push Yellow Nob Pull the SIM Tray

Place the SIM card In tray Inside Place the SIM Tray in SLOT and Push the Tray

We pursue a policy of continuous research and product development, Specifications and features are subject to change without notice

Logics PowerAMR Pvt Ltd http://poweramr.com Contact +91 8076963066

You might also like