Hangers

No. 226 hangers are designed for flush mounting inside the trough permitting
dust-tight or weather-proof operation. This type hanger allows for minimum
STYLE 226
obstruction of material flow in high capacity conveyors. Available with friction type
bearing.

No. 216 hangers are designed for heavy duty applications. This hanger is flush
mounted inside the trough permitting dust tight or weather proof operation.
STYLE 216
Hard iron or bronze bearings are normally furnished; however, the hanger can be
furnished with other bearings.

No. 220 hangers are designed for mount on top of the trough flanges and may be
used where dust-tight or weather proof operation is not required. This type hanger
STYLE 220
allows for minimum obstruction of material flow in high capacity conveyors.
Available with friction type bearing.

No. 230 hangers are designed for heavy duty applications where mounting on
STYLE 230 top of the trough flanges is required. Hard iron or bronze bearings are normally
furnished; however, other bearings are available.

No. 316 hangers are designed for heavy duty use in conveyors where abnormal
heat requires unequal expansion between the screw and conveyor trough. Hard
STYLE 316
iron or bronze bearings are normally furnished; however, this hanger can be
furnished with other bearings.

No. 326 hangers are designed to permit minimum obstruction of material flow and
are used in conveyors where abnormal heat requires unequal expansion between
STYLE 326
the screw and the conveyor trough. Hard iron or bronze bearings are normally
furnished, but other type bearings are available.

H-91
 Hangers

No. 60 hangers are furnished with a heavy duty, permanently lubricated and sealed,
self aligning ball bearing which permits temperatures up to 245º F. and will allow
STYLE 60
for up to 4º shaft misalignment. This hanger is mounted on top of the trough
flanges. Grease fitting can be furnished if specified.

No. 70 hangers are furnished with a heavy duty, permanently lubricated and sealed,
self aligning ball bearing which permit temperatures up to 245º F. and will allow
STYLE 70
for up to 4º shaft misalignment. This hanger is mounted inside the trough. Grease
fittings can be furnished if specified.

No. 30 hangers are designed for side mounting within the conveyor trough on the
STYLE 30 noncarrying side and permit a minimum of obstruction of material flow. Available
with friction type bearing.

No. 216F hangers are designed for heavy duty applications and are mounted inside
STYLE 216F of flared trough. Hard iron or bronze bearings are normally furnished; however,
other bearings are available.

The No. 19B hanger is similar in construction to the No. 18B except they are
mounted on top of the trough angles. Built-in ledges provide supports for the ends
STYLE 19B of the cover. They are streamline in design and permit free passage of the material.
They are regularly furnished with Arguto oil impregnated wood, hard iron, bronze,
or other special caps can be furnished.

Air-Purged hangers are recommended when handling dusty and abrasive materials
which contribute to shutdowns and hanger bearing failures. Air-swept hangers
are available for 9"-24" conveyors. They should not be used when handling hot
materials (over 250º F) or wet sticky materials or when handling non abrasive
materials when an inexpensive hanger will do the job satisfactorily. In service,
AIR-PURGED air-purged hangers deliver relatively trouble-free operation. They help solve noise
HANGER nuisance problems, and they help reduce power requirement because of the low
coefficient of fraction. Maximum trough loading should not exceed 15%. The air, at
approximately 1-1/4 PSI enters the housing at the top, passes over and around the
bearing, and is dissipated around the coupling shaft on both sides of the housing.
Thus the bearing is protected from dust and the material in the trough at all times.
Only 3 to 7 cu. ft. of air per minute is required to keep each hanger bearing clean.
H-92
 Hangers

Style 220 L

F
C

Pipe Tap 1/8"

Pipe Tab 1/8"
D

Conveyor couplings are used to join individual lengths of

conveyor screws and allow for rotation within the hanger M MSLOT
Slot

bearing. Mild steel couplings are normally furnished; Bolts

Bolts E
E B

however induction hardened bearing area couplings may

be furnished where highly abrasive materials are being
conveyed. Jig drilling allows for ease of installation. K

Conveyor Coupling Part M Weight

B C D E F H K L
Diameter Size Number* Slot Each
4 1 4CH2202 3 5/8 3 1/2 3/16 1/4 6 1/2 2 1 1/2 7 1/4 5/16 × 3 /4 5
6 1 1/2 6CH2203 4 1/2 4 1/2 3/16 3/8 8 3/4 2 1/2 2 9 3/4 7/16 × 1 1/16 7
1 1/2 9CH2203 6 1/8 4 1/2 1/4 3/8 12 1/4 2 1/2 2 13 1/2 9
9 7/16 × 1 1/16
2 9CH2204 6 1/8 4 1/2 1/4 3/8 12 1/4 2 1/2 2 13 1/2 11
1 1/2 10CH2203 6 3/8 4 1/2 1/4 3/8 13 1/4 2 1/2 2 14 1/2 10
10 7/16 × 1 1/16
2 10CH2204 6 3/8 4 1/2 1/4 3/8 13 1/4 2 1/2 2 14 1/2 12
2 12CH2204 7 3/4 5 3/8 1/2 15 3/4 2 1/2 2 17 1/2 16
12 2 7/16 12CH2205 7 3/4 5 3/8 1/2 15 3/4 2 1/2 3 17 1/2 9/16 × 1 5/16 21
3 12CH2206 7 3/4 5 3/8 1/2 15 3/4 2 1/2 3 17 1/2 28
2 7/16 14CH2205 9 1/4 5 1/2 1/2 17 3/4 2 1/2 3 19 1/2 26
14 9/16 × 1 5/16
3 14CH2206 9 1/4 5 1/2 1/2 17 3/4 2 1/2 3 19 1/2 33
16 3 16CH2206 10 5/8 5 1/2 1/2 19 3/4 2 1/2 3 21 1/2 9/16 × 1 5/16 39
3 18CH2206 12 1/8 6 1/2 5/8 22 1/4 3 1/2 3 24 1/2 41
18 11/16 × 13/16
3 7/16 18CH2207 12 1/8 6 1/2 5/8 22 1/4 3 1/2 4 24 1/2 49
3 20CH2206 13 1/2 6 1/2 5/8 24 1/4 3 1/2 3 26 1/2 43
20 11/16 × 13/16
3 7/16 20CH2207 13 1/2 6 1/2 5/8 24 1/4 3 1/2 4 26 1/2 51
24 3 7/16 24CH2207 16 1/2 6 5/8 5/8 28 1/4 3 1/2 4 30 1/2 11/16 Hole 57
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

Style 226 Pipe Tap

1/8"
No. 226 hangers are designed for flush mounting M SLOT
inside the trough permitting dust-tight or weather-
Bolts E
proof operation. This type hanger allows for minimum
obstruction of material flow in high capacity
conveyors. Also available with friction type bearing.
Conveyor Coupling Part M Weight
A B C D E F H K
Diameter Size Number* Slot Each
4 1 4CH2262 5 3 5/8 3 1/2 3/16 1/4 11/16 2 1 1/2 5/16 × 5/16 5
6 1 1/2 6CH2263 7 4 1/2 4 1/2 3/16 3/8 3/4 2 1/2 2 7/16 × 1 1/16 7
1 1/2 9CH2263 10 6 1/8 4 1/2 1/4 3/8 1 9
9 2 1/2 2 7/16 × 1 1/16
2 9CH2264 10 6 1/8 4 1/2 1/4 3/8 1 11
1 1/2 10CH2263 11 6 3/8 4 1/2 1/4 3/8 1 10
10 2 1/2 2 7/16 × 1 1/16
2 10CH2264 11 6 3/8 4 1/2 1/4 3/8 1 12
2 12CH2264 13 7 3/4 5 3/8 1/2 1 1/4 2 16
12 2 7/16 12CH2265 13 7 3/4 5 3/8 1/2 1 1/4 2 1/2 3 9/16 × 1 5/16 21
3 12CH2266 13 7 3/4 5 3/8 1/2 1 1/4 3 28
2 7/16 14CH2265 15 9 1/4 5 1/2 1/2 1 3/8 26
14 2 1/2 3 9/16 × 1 5/16
3 14CH2266 15 9 1/4 5 1/2 1/2 1 3/8 33
16 3 16CH2266 17 10 5/8 5 1/2 1/2 1 3/8 2 1/2 3 9/16 × 1 5/16 39
3 18CH2266 19 12 1/8 6 1/2 5/8 1 1/2 3 41
18 3 1/2 11/16 × 1 11/16
3 7/16 18CH2267 19 12 1/8 6 1/2 5/8 1 1/2 4 49
3 20CH2266 21 13 1/2 6 1/2 5/8 1 1/2 43
20 3 1/2 4 11/16 × 1 11/16
3 7/16 20CH2267 21 13 1/2 6 1/2 5/8 1 1/2 51
24 3 7/16 24CH2267 25 16 1/2 6 5/8 5/8 1 5/8 3 1/2 4 11/16 × 1 11/16 57
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

H-93
 Hangers

Style 216 A

Pipe Tap
Pipe Tab1/8"
1/8"
C
H

No. 216 hangers are designed for heavy duty M MSLOT

Slot

applications. This hanger is flush mounted inside BoltsBoltsEE D

B

the trough permitting dust tight or weather

proof operation. Hard iron or bronze bearings
are normally furnished; however, the hanger
can be furnished with other bearings. K

Conveyor Coupling Part M Weight

A B C D E F H K
Diameter Size Number* Slot Each
6 1 1/2 6CH2163 7 4 1/2 4 1/2 3/16 3/8 3/4 2 1/2 2 7/16 × 1 1/16 5
1 1/2 9CH2163 10 6 1/8 4 1/2 1/4 3/8 1 2 1/2 2 7
9 7/16 × 1 1/16
2 9CH2164 10 6 1/8 4 1/2 1/4 3/8 1 2 1/2 2 9
1 1/2 10CH2163 11 6 3/8 4 1/2 1/4 3/8 1 2 1/2 2 8
10 7/16 × 1 1/16
2 10CH2164 11 6 3/8 4 1/2 1/4 3/8 1 2 1/2 2 10
2 12CH2164 13 7 3/4 5 3/8 1/2 1 1/4 2 1/2 2 14
12 2 7/16 12CH2165 13 7 3/4 5 3/8 1/2 1 1/4 2 1/2 3 9/16 × 1 5/16 18
3 12CH2166 13 7 3/4 5 3/8 1/2 1 1/4 2 1/2 3 21
2 7/16 14CH2165 15 9 1/4 5 1/2 1/2 1 3/8 2 1/2 3 23
14 9/16 × 1 5/16
3 14CH2166 15 9 1/4 5 1/2 1/2 1 3/8 2 1/2 3 25
16 3 16CH2166 17 10 5/8 5 1/2 1/2 1 3/8 2 1/2 3 9/16 × 1 5/16 28
3 18CH2166 19 12 1/8 6 1/2 5/8 1 1/2 3 1/2 3 34
18 11/16 × 1 11/16
3 7/16 18CH2167 19 12 1/8 6 1/2 5/8 1 1/2 3 1/2 4 44
3 20CH2166 21 13 1/2 6 1/2 5/8 1 1/2 3 1/2 3 36
20 11/16 × 1 11/16
3 7/16 20CH2167 21 13 1/2 6 1/2 5/8 1 1/2 3 1/2 4 47
24 3 7/16 24CH2167 25 16 1/2 6 5/8 5/8 1 5/8 3 1/2 4 11/16 × 1 11/16 53
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

Style 230 Pipe Tap

1/8"
No. 230 hangers are designed for heavy duty M SLOT
Bolts E
applications where mounting on top of the trough flange
is required. Hard iron or bronze bearings are normally
furnished; however, other bearings are available.

Conveyor Coupling Part M Weight

B C D E F H K L
Diameter Size Number* Slot Each
6 1 1/2 6CH2303 4 1/2 4 1/2 3/16 3/8 8 3/4 2 1/2 2 9 3/4 7/16 × 1 1/16 6
1 1/2 9CH2303 6 1/8 4 1/2 1/4 3/8 12 1/4 2 1/2 2 13 1/2 8
9 7/16 × 1 1/16
2 9CH2304 6 1/8 4 1/2 1/4 3/8 12 1/4 2 1/2 2 13 1/2 10
1 1/2 10CH2303 63/8 4 1/2 1/4 3/8 13 1/4 2 1/2 2 14 1/2 9
10 7/16 × 1 1/16
2 10CH2304 63/8 4 1/2 1/4 3/8 13 1/4 2 1/2 2 14 1/2 11
2 12CH2304 7 3/4 5 3/8 1/2 15 3/4 2 1/2 2 17 1/2 15
12 2 7/16 12CH2305 7 3/4 5 3/8 1/2 15 3/4 2 1/2 3 17 1/2 9/16 × 1 5/16 20
3 12CH2306 7 3/4 5 3/8 1/2 15 3/4 2 1/2 3 17 1/2 25
2 7/16 14CH2305 9 1/4 5 1/2 1/2 17 3/4 2 1/2 3 19 1/2 24
14 9/16 × 1 5/16
3 14CH2306 9 1/4 5 1/2 1/2 17 3/4 2 1/2 3 19 1/2 29
16 3 16CH2306 10 5/8 5 1/2 1/2 19 3/4 2 1/2 3 21 1/2 9/16 × 1 5/16 35
3 18CH2306 12 1/8 6 1/2 5/8 22 1/4 3 1/2 3 24 1/2 34
18 1 1/16 × 13/16
3 7/16 18CH2307 12 1/8 6 1/2 5/8 22 1/4 3 1/2 4 24 1/2 47
3 20CH2306 13 1/2 6 1/2 5/8 24 1/4 3 1/2 3 26 1/2 40
20 1 1/16 × 13/16
3 7/16 20CH2307 13 1/2 6 1/2 5/8 24 1/4 3 1/2 4 26 1/2 49
24 3 7/16 24CH2307 16 1/2 6 5/8 5/8 28 1/4 3 1/2 4 30 1/2 1 1/16 Holes 55
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

H-94
 Hangers

Style 316 Pipe Tap

1/8"
No. 316 hangers are designed for heavy duty use in
conveyors where abnormal heat requires unequal Bolts E
expansion between the screw and conveyor trough. Hard
iron or bronze bearings are normally used; however,
this hanger can be furnished with other bearings.

Style 326
No. 326 hangers are designed to permit minimum obstruction of material flow and are used in
conveyors where abnormal heat requires unequal expansion between the screw and the conveyor
trough. Hard iron or bronze bearings are normally used, but other type bearings are available.
Conveyor Coupling Part Number
A B C D E F H K
Diameter Size Style 316* Style 326*
6 1 1/2 6CH3163 6CH3263 7 4 1/2 6 3/16 3/8 3/4 4 1/2 2
1 1/2 9CH3163 9CH3263 10 6 1/8 6 3/16 3/8 1 4 1/2 2
9
2 9CH3164 9CH3264 10 6 1/8 6 3/16 3/8 1 4 1/2 2
1 1/2 10CH3163 10CH3263 11 6 3/8 6 3/16 3/8 1 4 1/2 2
10
2 10CH3164 10CH3264 11 6 3/8 6 3/16 3/8 1 4 1/2 2
2 12CH3164 12CH3264 13 7 3/4 6 1/2 1/4 1/2 1 1/4 5 2
12 2 7/16 12CH3165 12CH3265 13 7 3/4 6 1/2 1/4 1/2 1 1/4 5 3
3 12CH3166 12CH3266 13 7 3/4 6 1/2 1/4 1/2 1 1/4 5 3
2 7/16 14CH3165 14CH3265 15 9 1/4 6 1/2 1/4 1/2 1 3/8 5 3
14
3 14CH3166 14CH3266 15 9 1/4 6 1/2 1/4 1/2 1 3/8 5 3
16 3 16CH3166 16CH3266 17 10 5/8 6 1/2 1/4 1/2 1 3/8 5 3
3 18CH3166 18CH3266 19 12 1/8 7 1/4 5/8 1 5/8 5 1/4 3
18
3 7/16 18CH3167 18CH3267 19 12 1/8 7 1/4 5/8 1 5/8 5 1/4 4
3 20CH3166 20CH3266 21 13 1/2 7 1/4 5/8 1 5/8 5 1/4 3
20
3 7/16 20CH3167 20CH3267 21 13 1/2 7 1/4 5/8 1 5/8 5 1/4 4
24 3 7/16 24CH3167 24CH3267 25 16 1/2 7 1/4 5/8 1 3/4 5 1/4 4
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

A
Air-Purged Hanger H

Air purged hangers are B - Bolt Size

recommended when handling D
T
dusty and abrasive materials which Standard
contribute to shut-downs and hanger Coupling
bearing failures. They should not be Drilling
L
used when handling hot materials
(over 250°F) or wet sticky materials
or when handling nonabrasive Conveyor Part Shaft Weight
A B C D F H L T
materials when an inexpensive Diameter Number Diameter (lb)
9 9CHAPH3 1 1/2 15
hanger will do the job satisfactorily. 9CHAPH4 2 20
10 3/8 4 1/2 6 1/8 1 1/4 1 2 1/4
Maximum trough loading should 12CHAPH4 2 30 2
not exceed 15%. The air, at 12 12CHAPH5 2 7/16 52 13 1/2 5 7 3/4 1 1/4 1 1/4 3 1/4
approximately 11/4 PSI, enters the 12CHAPH6 3 68 3
housing at the top, passes over and 14CHAPH5 2 7/16 60
14 15 1/2 5 9 1/4 1 1/4 1 3/8 3 3/8
14CHAPH6 3 74
around the bearing, and is dissipated
16 16CHAPH6 3 77 17 1/2 5 10 5/8 1 1/4 1 3/8 3 3/8
around the coupling shaft on both 18 18CHAPH6 3 91 19 5/8 6 12 1/8 1 3/4 1 5/8 3 1/2
sides of the housing. Only 3 to 7 cu. 20CHAPH6 3 105 3
20 21 5/8 6 13 1/2 1 3/4 1 5/8 1/2
ft. of air per minute is required to 20CHAPH7 3 7/16 140 4
keep each hanger bearing clean. 24 24CHAPH7 3 7/16 155 25 5/8 6 16 1/2 1 3/4 1 5/8 4 1/2
H-95
 Hangers

Style 30
No. 30 hangers are designed for side mounting
within the conveyor trough on the non-carrying
side and permit a minimum of obstruction of
material flow. Available with friction type bearing.

Conveyor Coupling Part Weight

A B C D E F G H
Diameter Size Number* Each
6 1 1/2 6CH303 3 1/2 4 1/4 1 1/2 3/8 5/16 3 1/8 1/2 2 3
1 1/2 9CH303 5 5 7/8 1 1/2 3/8 3/8 4 1/4 1/2 2 6
9
2 9CH304 5 5 7/8 1 1/2 1/2 3/8 4 1/4 1/2 2 8
1 1/2 10CH303 5 1/2 6 3/8 1 1/2 3/8 1/2 4 3/8 3/4 2 8
10
2 10CH304 5 1/2 6 3/8 1 1/2 1/2 1/2 4 3/8 3/4 2 9
2 12CH304 6 1/2 7 1/2 1 1/2 1/2 1/2 5 1/2 3/4 2 12
12 2 7/16 12CH305 6 1/2 7 1/2 2 1/2 1/2 5 1/2 3/4 3 18
3 12CH306 6 1/2 7 1/2 2 5/8 1/2 5 1/2 3/4 3 20
2 7/16 14CH305 7 1/2 9 2 1/2 5/8 6 7/8 7/8 3 20
14
3 14CH306 7 1/2 9 2 5/8 5/8 6 7/8 7/8 3 22
16 3 16CH306 8 1/2 10 3/8 2 5/8 5/8 8 1 3 32
3 18CH306 9 1/2 11 7/8 2 3/4 5/8 8 1 1/4 3 30
18
3 7/16 18CH307 9 1/2 11 7/8 3 3/4 5/8 8 1 1/4 4 33
3 20CH306 10 1/2 13 1/4 2 3/4 5/8 10 1/4 1 1/4 3 32
20
3 7/16 20CH307 10 1/2 13 1/4 3 3/4 5/8 10 1/4 1 1/4 4 38
24 3 7/16 24CH307 12 1/2 16 1/4 3 3/4 3/4 12 3/4 1 1/2 4 46
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

Style 216F AA CC
HH
FF Pipe Tap 1/8"
Pipe Tap 1/8"

No. 216F hangers are designed for M Slot

M Slot

heavy duty applications and are DD Bolts

Bolts E E
mounted inside of flared trough. BB
Hard iron or bronze bearings are
normally furnished; how­ever,
other bearings are available.
KK

Conveyor Coupling Part Weight M

A B C D E F H K
Diameter Size Number* Each Slot
6 1 1/2 6CH216F3 14 7 7 1/2 1/4 3/8 7/8 6 2 9 7/16 × 3/4
1 1/2 9CH216F3 14
9 18 9 9 3/16 3/8 1 7 2 7/16 × 15/16
2 9CH216F4 17
2 12CH216F4 2 24
12 2 7/16 12CH216F5 22 10 9 3/8 1/2 1 1/4 7 28 9/16 × 15/16
3
3 12CH216F6 32
2 7/16 14CH216F5 31
14 24 11 9 3/8 1/2 1 1/8 7 3 9/16 × 15/16
3 14CH216F6 34
16 3 16CH216F6 28 11 1/2 9 1/2 5/8 1 1/4 7 3 38 11/16 × 1
3 18CH216F6 3 52
18 31 12 1/8 10 1/2 5/8 1 1/2 8 11/16 × 15/16
3 7/16 18CH216F7 4 61
3 20CH216F6 3 55
20 34 13 1/2 10 1/2 5/8 1 1/2 8 11/16 × 15/16
3 7/16 20CH216F7 4 64
24 3 7/16 24CH216F7 40 16 1/2 10 5/8 5/8 1 5/8 8 4 71 11/16 × 15/16
*Refer to Page H-99 for bearings. For hangers with oil pipe add –0 to part number

H-96
 Hangers

Style 60
No. 60 hangers are furnished with a
heavy duty, permanently lubricated
and sealed, self-aligning ball bearing M Slot
which permits temperatures up to Bolts E
245º F. and will allow for up to 4º shaft
misalignment. This hanger is mounted
on top of the trough flanges. Grease
fitting can be furnished if specified.
Conveyor Coupling Part Weight
A B C D E F H J M Slot
Diameter Size Number* Each
6 1 1/2 6CH603 9 3/4 4 1/2 4 1/2 3/16 3/8 8 3/4 1 11/16 2 7 7/16 × 11/16
1 1/2 9CH603 13 1/2 6 1/8 4 1/2 1/4 3/8 12 1/4 1 11/16 2 1/2 8 7/16 × 11/16
9
2 9CH604 13 1/2 6 1/8 4 1/2 1/4 3/8 12 1/4 1 3/4 2 1/2 9 7/16 × 11/16
1 1/2 10CH603 14 1/2 6 3/8 4 1/2 1/4 3/8 13 1/4 1 11/16 2 1/2 9 7/16 × 15/16
10
2 10CH604 14 1/2 6 3/8 4 1/2 1/4 3/8 13 1/4 1 3/4 2 1/2 10 7/16 × 15/16
2 12CH604 17 1/2 7 3/4 5 3/8 1/2 15 3/4 1 3/4 2 1/2 12 9/16 × 15/16
12 2 7/16 12CH605 17 1/2 7 3/4 5 3/8 1/2 15 3/4 1 63/64 2 1/2 20 9/16 × 15/16
3 12CH606 17 1/2 7 3/4 5 3/8 1/2 15 3/4 2 11/16 2 1/2 30 9/16 × 15/16
2 7/16 14CH605 19 1/2 9 1/4 5 1/2 1/2 17 3/4 1 63/64 2 1/2 21 9/16 × 15/16
14
3 14CH606 19 1/2 9 1/4 5 1/2 1/2 17 3/4 2 11/32 2 1/2 32 9/16 × 15/16
16 3 16CH606 21 1/2 10 5/8 5 1/2 1/2 19 3/4 2 11/32 2 1/2 35 9/16 × 15/16
18 3 18CH606 24 1/2 12 1/8 6 1/2 5/8 22 1/4 2 11/32 3 1/2 40 11/16 × 1 11/16
20 3 20CH606 26 1/2 13 1/2 6 1/2 5/8 24 1/4 2 11/32 3 1/2 45 11/16 × 1 11/16
24 3 7/16 24CH607 30 1/2 16 1/2 6 5/8 5/8 28 1/4 2 31/64 3 1/2 58 11/16 × 1 11/16
*For hangers with oil pipe add –0 to part number

Style 70
No. 70 hangers are furnished with a
heavy duty, permanently lubricated
and sealed, self aligning ball bearing Bolts E
M Slot
which permits temperatures up to
245º F. and will allow for up to 4º
shaft misalignment. This hanger is
mounted inside the trough. Grease
fitting can be furnished if specified.
Conveyor Coupling Part Weight
A B C D E F G H M Slot
Diameter Size Number* Each
6 1 1/2 6CH703 7 4 1/2 4 1/2 3/4 3/8 3/16 1 11/16 1 1/2 7 7/16 × 11/16
1 1/2 9CH703 10 6 1/8 4 1/2 1 3/8 1/4 1 11/16 1 3/4 8
9 7/16 × 11/16
2 9CH704 10 6 1/8 4 1/2 1 3/8 1/4 1 3/4 1 3/4 9
1 1/2 10CH703 11 6 3/8 4 1/2 1 3/8 1/4 1 11/16 1 3/4 9
10 7/16 × 11/16
2 10CH704 11 6 3/8 4 1/2 1 3/8 1/4 1 3/4 1 3/4 10
2 12CH704 13 7 3/4 5 1 1/4 1/2 3/8 1 3/4 2 1/8 12
12 2 7/16 12CH705 13 7 3/4 5 1 1/4 1/2 3/8 1 63/64 2 1/8 20 9/16 × 15/16
3 12CH706 13 7 3/4 5 1 1/4 1/2 3/8 2 11/32 2 1/8 30
2 7/16 14CH705 15 9 1/4 5 1 3/8 1/2 1/2 1 63/64 2 1/4 21
14 9/16 × 15/16
3 14CH706 15 9 1/4 5 1 3/8 1/2 1/2 2 11/32 2 1/4 32
16 3 16CH706 17 10 5/8 5 1 3/8 1/2 1/2 2 11/32 2 1/4 35 9/16 × 15/16
18 3 18CH706 19 12 1/8 6 1 1/2 5/8 1/2 2 11/32 2 1/2 40 11/16 × 13/16
20 3 20CH706 21 13 1/2 6 1 1/2 5/8 1/2 2 11/32 2 1/2 45 11/16 × 13/16
24 3 7/16 24CH707 25 16 1/2 6 1 5/8 5/8 5/8 2 11/32 2 5/8 58 11/16 Holes
*For hangers with oil pipe add –0 to part number

H-97
 Hangers

Style 19B P
Size of Pipe
The No. 19-B Hanger is similar in
construction to the No. 18-B except
they are mounted on top of the
trough angles. Built-in ledges provide
supports for the ends of the cover.
They are streamlined in design and
permit free passage of the material. H
Size of Bolts
Top half is furnished with bronze
bearing. Bottom half­can be
supplied in oil impregnated wood,
hard iron, or other special caps
may be furnished on request.

Conveyor Coupling Part

A B C D F H J P Weight
Diameter Size Number
6 1 1/2 6CH19B3 9 7/8 4 1/2 1 7/8 7/8 8 3/4 9/16 6 1/2 1/8 8.5
1 1/2 9CH19B3 13 1/2 6 1/8 1 3/4 1 12 1/4 9/16 9 1/2 1/8 13.0
9
2 9CH19B4 13 1/2 6 1/8 1 3/4 1 12 1/4 9/16 9 1/2 1/8 15.5
1 1/2 10CH19B3 14 1/2 6 3/8 1 3/4 1 13 1/4 9/16 10 1/2 1/8 14.0
10
2 10CH19B4 14 1/2 6 3/8 1 3/4 1 13 1/4 9/16 10 1/2 1/8 14.0
2 12CH19B4 17 7 3/4 2 1 1/4 15 3/4 9/16 12 1/2 1/8 24.0
12 2 7/16 12CH19B5 17 7 3/4 2 1/8 15/6 15 3/4 9/16 12 1/2 1/8 24.5
3 12CH19B6 17 7 3/4 2 1/8 15/6 15 3/4 9/16 12 1/2 1/8 24.5
2 7/16 14CH19B5 19 1/4 9 1/4 3 1 1/2 17 3/4 9/16 14 1/2 1/8 37.0
14
3 14CH19B6 19 1/4 9 1/4 3 1 1/2 17 3/4 9/16 14 1/4 1/8 37.0
16 3 16CH19B6 21 1/4 10 5/8 3 1 3/4 19 3/4 11/16 16 1/2 1/8 45.0
18 3 18CH19B6 23 3/4 12 1/8 3 1 5/8 22 1/4 11/16 18 1/2 1/8 48.5
20 3 7/16 20CH19B7 26 1/4 13 1/2 4 1 1/2 24 1/4 13/16 20 1/8 60.0

H-98
 Screw Conveyor Hanger
Bearing Selection Application

Maximum Material
Styles Self Some Suggested
Bearing Material Operating FDA Comments
Available Lube Uses
Temperature (°F) Complaint

Grain, Feed,
WOOD 160° 220, 216, 19B – Yes Good general purpose.
Fertilizer

Material USDA approved. Does

UHMW 225° 220, 216 Yes Yes Food
not swell in water.
Chemical,
MARTIN HARD IRON 500° 220 – Yes Cement, Requires Hardened Shaft
Aggregate
Requires hardened shaft. Can
Lime, Cement,
CAST HARD IRON 500° 220, 216, 19B – – be noisy. Lubrication required
Salt, Gypsum
in some applications.
Chemical,
CERAMIC1 1,000° 220, 216 Yes – Requires hardened shafts.
Cement, Food
Chemical,
Requires Stellite insert in
STELLITE 1000° 220, 216 – – Cement,
shaft.
Aggregate
FOOD GRADE Food, Grain,
300° 220 Yes Yes For dry application.
ENGINEERED NYLON Fertilizer
Chemical,
NYLATRON GS 250° 220, 19B – Yes Handling, Grain, Very low load capacity.
Feed
Grain, Feed, High quality bearings. High
MARTIN BRONZE 850° 220 – Yes
Processing load capacity.
Grain, Feed,
Recommended for non-
MARTIN HDPE 200° 220 Yes Yes Chemical
abrasive applications
Handling
Grain, Chemical,
MARTIN URETHANE 200° 220 – Yes Good general purpose.
Fertilizer
C­hemical, Requires hardened shaft. Can
MARTIN WHITE IRON 500° 220 – – Cement, be noisy. Lubrication required
Aggregate in some applications.
Fiberglass fabric. Good for
GATKE 400° 220, 216 – – Chemical
higher speeds.
Registered Trademark
ERTALYTE® 200° 220, 216 Yes – Food of Quadrant Engineering
Products
Non-abrasive
BALL BEARING 180° 60, 70 – – General purpose use.
applications
1
Higher temperature ceramics are available.

H-99
 Hanger
Bearings

Hanger Types Shaft Diameter Part Number Bearing

1 1/2 CHB2163*

216 2 CHB2164*

230 2 7/16 CHB2165*

316 3 CHB2166*

3 7/16 CHB2167*

*H — Hard Iron *W — Wood *BR –­ Bronze *U — UHMW *G — Gatke *ER – Ertalyte® *C — Ceramic * ST — Stellite * UR - Urethane
*Oil hole is furnished on hard iron and bronze standard.

Hanger Types Shaft Diameter Part Number Bearing

1 CHB2202*

220 1 1/2 CHB2203*

226 2 CHB2204*

326 2 7/16 CHB2205*

30 3 CHB2206*

3 7/16 CHB2207*

*H — Cast Hard Iron with oil hole *W — Wood *N — Nylatron *P – HDPE *G — Gatke *ER – Ertalyte®
*MHI — Martin Hard iron (oil impregnated) *MCB — Melamine (Furnished Less Flanges) *C – Ceramic *WN – White Nylon *WI – White Iron
*MBR — Martin Bronze (oil impregnated) *U — UHMW *UR – Urethane

Hanger Types Shaft Diameter Part Number Bearing

1 1/2 CHB603

2 CHB604
60 Ball Bearing
2 7/16 CHB605
70 Ball Bearing
3 CHB606

3 7/16 CHB607

Note: New style bearings are available with slinger shield one side.

Hanger Types Shaft Diameter Part Number Bearing

1 1/2 CHB18B3*

2 CHB18B4*
18B
2 7/16 CHB18B5*
19B
3 CHB18B6*

3 7/16 CHB18B7*

*W—Wood *H—Hard Iron *N—Nylatron *G—Gatke

Note: Furnished as bottom cap only.
Ertalyte® is Registered Trademarks of Quadrant Engineered Plastic Products.

H-100