Cisco Catalyst 9400 Series Switches Hardware Installation Guide
First Published: 2017-09-20
Last Modified: 2024-03-19
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Safety Warnings
Network Equipment-Building System (NEBS) Statements
telecommunications equipment in the United States. It is not a legal or regulatory requirement, but rather an
industry requirement.
The following NEBS statements apply to the Cisco Catalyst 9400 Series Switches:
Warning Statement 7003—Shielded Cable Shielded Cable Requirements for Intrabuilding Lightning Surge
The intrabuilding port(s) of the equipment or subassembly must use shielded intrabuilding cabling/wiring that
is grounded at both ends.
The following port(s) are considered intrabuilding ports on this equipment:
RJ45 copper Ethernet Ports
Note Statement 7004—Special Accessories Required to Comply with GR-1089 Emission and Immunity
Requirements
To comply with the emission and immunity requirements of GR-1089, shielded cables are required for the
following ports:
Ethernet Ports
Warning Statement 7005—Intrabuilding Lightning Surge and AC Power Fault
The intrabuilding port(s) of the equipment or subassembly must not be metallically connected to interfaces
that connect to the outside plant (OSP) or its wiring. These interfaces are designed for use as intrabuilding
interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed
OSP cabling. The addition of primary protectors is not sufficient protection to connect these interfaces
metallically to OSP wiring.
This statement applies to the intrabuilding ports listed below:
RJ45 copper Ethernet Ports
Cisco Catalyst 9400 Series Switches Hardware Installation Guide
3
Product Overview
Catalyst 9407R Switch
Feature Description
Fan tray assembly The switch supports a single front and rear serviceable and hot-swappable fan tray with 8 fans.
Supported model number (add = for spare)—C9404-FAN
See Fan Tray Assembly Overview, on page 17 and Fan Tray LEDs, on page 169.
Power supplies The chassis supports up to four field-replaceable AC-input and DC-input power supply modules.
Supported model numbers (add = for spare):
• C9400-PWR-2100AC
• C9400-PWR-3200AC
• C9400-PWR-3200ACT
• C9400-PWR-3200DC
See Power Supply Module Overview, on page 20 and Power Supply LEDs, on page 170.
Backplane With C9400-SUP-1, the backplane bandwidth is 80 Gbps.
With C9400-SUP-1XL, C9400-SUP-1XL-Y, and C9400X-SUP-2, the backplane bandwidth is 240
Gbps for each payload module slot.
With C9400X-SUP-2XL, the backplane bandwidth is 480 Gbps for each payload module slot.
RFID Tag Has a built-in, front-facing, non-removable, passive RFID tag that uses Ultra High Frequency
(UHF) RFID technology and requires an RFID reader with compatible software. For more
information, see Radio Frequency Identification (RFID) on Cisco Catalyst 9000 Family Switches.
Catalyst 9407R Switch
The Catalyst 9407R Switch is a seven-slot modular chassis, with two redundant supervisor module slots, five
line card slots with up to 240 front panel ports, one non-redundant fan tray assembly, and a provision to
accommodate up to eight power supply modules.
Front View of the Catalyst 9407R Switch
The figure shows a front view of the chassis, with the major components identified:
Cisco Catalyst 9400 Series Switches Hardware Installation Guide
9
Product Overview
Catalyst 9407R Switch
1 Chassis handholds 5 Supervisor module slots (3 and 4)
2 Power supply modules 6 Chassis Radio Frequency ID (RFID)
3 Line card slots (1,2, 5,6, and 7) 7 System ground
4 Fan tray assembly 8 Chassis model number
Rear View of the Catalyst 9407R Switch
The figure shows a rear view of the chassis, with the major components identified:
Cisco Catalyst 9400 Series Switches Hardware Installation Guide
10
Product Overview
Catalyst 9407R Switch
1 Access to remove fan tray from the rear 2 Blue beacon LED on the rear panel of the fan
tray (always matches the blue beacon on the
front panel of the fan tray)
Table 2: Catalyst 9407R Switch Features
Feature Description
Product ID Chassis model number (add = for spare)—Cisco Catalyst 9400 Series 7 Slot Chassis(C9407R)
Chassis Has seven horizontal slots. Slots are numbered 1 (top) to 7 (bottom).
Cisco Catalyst 9400 Series Switches Hardware Installation Guide
11
Product Overview
Catalyst 9407R Switch
Feature Description
Supervisor modules Supports 1+1 supervisor module redundancy for integrated resiliency. Supported model numbers
(add = for spare):
• Cisco Catalyst 9400 Series Supervisor 1 Module (C9400-SUP-1)
• Cisco Catalyst 9400 Series Supervisor 1XL Module ( C9400-SUP-1XL)
• Cisco Catalyst 9400 Series Supervisor 1XL-Y 25G Module (C9400-SUP-1XL-Y)
• Cisco Catalyst 9400 Series Supervisor 2 Module (C9400X-SUP-2)
• Cisco Catalyst 9400 Series Supervisor 2XL Module (C9400X-SUP-2XL)
Supervisor modules:
• Must be installed in slots numbered 3 and 4 only.
• Have minimum software release version requirements. Refer to your software release notes
for this information.
See Cisco Catalyst 9400 Series Supervisor Module Installation Note.
Line Cards Accomodates five line cards. Supported model numbers (add = for spare):
• Cisco Catalyst 9400 Series 12-Port 40G/100G Module (C9400-LC-12QC)
• Cisco Catalyst 9400 Series 24-Port SFP Module (C9400-LC-24S)
• Cisco Catalyst 9400 Series 24-Port SFP/SFP+ Module (C9400-LC-24XS)
• Cisco Catalyst 9400 Series 24-Port 10G/25G Module (C9400-LC-24XY)
• Cisco Catalyst 9400 Series 48-Port Gigabit Ethernet UPOE+ 10/100/1000 Module
(C9400-LC-48H)
• Cisco Catalyst 9400 Series 48-Port UPOE+ 100 Mbps/1G/2.5G/5G Multigigabit Module
(C9400-LC-48HN)
• Cisco Catalyst 9400 Series 48-Port UPOE+ 100 Mbps/1G/2.5G/5G/10G Multigigabit Module
(C9400-LC-48HX)
• Cisco Catalyst 9400 Series 48-Port Gigabit Ethernet POE/POE+ Module (C9400-LC-48P)
• Cisco Catalyst 9400 Series 48-Port SFP Module (C9400-LC-48S)
• Cisco Catalyst 9400 Series 48-Port 10/100/1000 Module (C9400-LC-48T)
• Cisco Catalyst 9400 Series 48-Port 100 Mbps/1G/2.5G/5G/10G Multigigabit Module
(C9400-LC-48TX)
• Cisco Catalyst 9400 Series 48-Port UPOE 10/100/1000 Module (C9400-LC-48U)
• Cisco Catalyst 9400 Series 48-Port UPOE Multigigabit Module (C9400-LC-48UX)
• Cisco Catalyst 9400 Series 48-Port SFP/SFP+ Module (C9400-LC-48XS)
See Cisco Catalyst 9400 Series Line Card Installation Note.
Cisco Catalyst 9400 Series Switches Hardware Installation Guide
12
Product Overview
Catalyst 9410R Switch
Feature Description
Fan tray assembly The switch supports a single front and rear serviceable and hot-swappable fan tray with 12 fans.
Supported model number (add = for spare)—C9407-FAN
See Fan Tray Assembly Overview, on page 17 and Fan Tray LEDs, on page 169.
Power supplies The chassis supports up to eight field-replaceable AC-input and DC-input power supply modules.
Supported model numbers (add = for spare):
• C9400-PWR-2100AC
• C9400-PWR-3200AC
• C9400-PWR-3200ACT
• C9400-PWR-3200DC
See Power Supply Module Overview, on page 20 and Power Supply LEDs, on page 170.
Backplane With C9400-SUP-1, the backplane bandwidth is 80Gbps.
With C9400-SUP-1XL and C9400-SUP-1XL-Y, the backplane bandwidth is 120 Gbps for each
payload module slot.
With C9400X-SUP-2, the backplane bandwidth is 240 Gbps for each payload module slot.
With C9400X-SUP-2XL, the backplane bandwidth is 480 Gbps for each payload module slot.
RFID Tag Has a built-in, front-facing, non-removable, passive RFID tag that uses Ultra High Frequency
(UHF) RFID technology and requires an RFID reader with compatible software. For more
information, see Radio Frequency Identification (RFID) on Cisco Catalyst 9000 Family Switches.
Catalyst 9410R Switch
The Catalyst 9410R Switch is a ten-slot modular chassis, with two redundant supervisor module slots, eight
line card slots with up to 384 1-Gigabit Ethernet front panel ports, one non-redundant fan tray assembly, and
a provision to accommodate up to eight power supply modules.
Front View of the Catalyst 9410R Switch
The figure shows a front view of the chassis, with the major components identified:
Cisco Catalyst 9400 Series Switches Hardware Installation Guide
13
