Subnetting Implementation in Cisco Packet
Tracer
Steps to Configure and Verify Three Router Connections in Cisco Packet
Tracer:
Step 1: First, open the Cisco packet tracer desktop and select the devices given below:
S.N
O Device Model-Name Qty.
1. PC pc 6
2. Switch PT-Switch 3
3. Router PT-Router 3
IP Addressing Table for PCs
Devic Subnet
S.NO e IPv4 Address Mask Default-Gateway
1. pc0 192.168.1.2 255.255.255.0 192.168.1.1
2. pc1 192.168.1.3 255.255.255.0 192.168.1.1
3. pc2 192.168.2.2 255.255.255.0 192.168.2.1
4. pc3 192.168.2.3 255.255.255.0 192.168.2.1
5. pc4 192.168.3.2 255.255.255.0 192.168.3.1
6. pc5 192.168.3.3 255.255.255.0 192.168.3.1
Then, create a network topology as shown below the image.
Use an Automatic connecting cable to connect the devices with others.
Step 2: Configure the PCs (hosts) with IPv4 address and Subnet Mask according to
the IP addressing table given above.
To assign an IP address in PC0, click on PC0.
Then, go to desktop and then IP configuration and there you will IPv4
configuration.
Fill IPv4 address and subnet mask.
Assigning IP address using the ipconfig command.
Or we can also assign an IP address with the help of a command.
Go to the command terminal of the PC.
Then, type ipconfig <IPv4 address><subnet mask><default gateway>(if needed)
Example: ipconfig 192.168.1.2 255.255.255.0 192.168.1.1
Repeat the same procedure with other PCs to configure them thoroughly.
Step 3: Configure router with IP address and subnet mask.
IP Addressing Table Router
S.NO Device Interface IPv4 Address Subnet mask
FastEthernet0/0 192.168.1.1 255.255.255.0
router0
1. Serial2/0 11.0.0.1 255.0.0.0
Serial 2/0 11.0.0.2 255.0.0.0
router1
2. Serial 3/0 12.0.0.1 255.0.0.0
FastEthernet0/0 192.168.3.1 255.255.255.0
router 3
3. Serial2/0 12.0.0.2 255.0.0.0
To assign an IP address in router0, click on router0.
Then, go to config and then Interfaces.
Then, configure the IP address in FastEthernet and serial ports according to IP
addressing Table.
Fill IPv4 address and subnet mask.
Repeat the same procedure with other routers to configure them thoroughly.
Step 4: After configuring all of the devices we need to assign the routes to the routers.
To assign static routes to the particular router:
First, click on router0 then Go to CLI.
Then type the commands and IP information given below.
CLI command : ip route <network id> <subnet mask><next hop>
Static Routes for Router0 are given below:
Router(config)#ip route 192.168.2.0 255.255.255.0 11.0.0.2
Router(config)#ip route 11.0.0.0 255.0.0.0 11.0.0.2
Router(config)#ip route 192.168.3.0 255.255.255.0 11.0.0.2
Router(config)#ip route 12.0.0.0 255.0.0.0 11.0.0.2
Static Routes for Router1 are given below:
Router(config)#ip route 192.168.1.0 255.255.255.0 11.0.0.1
Router(config)#ip route 11.0.0.0 255.0.0.0 11.0.0.1
Router(config)#ip route 192.168.3.0 255.255.255.0 12.0.0.2
Router(config)#ip route 12.0.0.0 255.0.0.0 12.0.0.2
Static Routes for Router2 are given below:
Router(config)#ip route 192.168.1.0 255.255.255.0 12.0.0.1
Router(config)#ip route 11.0.0.0 255.0.0.0 12.0.0.1
Router(config)#ip route 12.0.0.0 255.0.0.0 12.0.0.1
Router(config)#ip route 192.168.2.0 255.255.255.0 12.0.0.1
Step 5: Verifying the network by pinging the IP address of any PC. We will use the
ping command to do so.
First, click on PC0 then Go to the command prompt
Then type ping <IP address of targeted node>
As we can see in the below image we are getting replies which means the
connection is working very fine
Example : ping 192.168.2.2
A simulation of the experiment is given below we are sending PDU from PC0 to
PC3 and PC2 to PC4:
