mini Camera Alarm Clock Operation Manual
The device is surveillance equipment only applicable to legal
purposes. If the device is used for illegal purposes,
all legal liabilities and consequences thereof shall be irrelevant to our
company.
1. APP download and installation; IOS/ANDRIOID (search the APP
name "LOOKCAMPro")
2. Scan the QR code to download and install the APP (Figure 2)
(All the authorities prompted upon APP download shall be enabled)
3. Camera indicator status;
Yellow indicates that the device is charging (off when fully charged)
Red indicates WiFi/AP peer-to-peer mode (slow blinking means the host is providing
a hotspot/account)
Blue indicates connection to the internet (fast blinking indicates linkage in progress,
permanent lighting indicates linkage completion)
(If you don't know the exact status, simply reset the camera to switch it to the
peer-to-peer mode)
Precautions: the resetting must be done when the red light is fast blinking or slow blinking,
otherwise it will not be functioning. Press and hold the reset key for 5 sec or so, to light off all the
camera's indicators. Then the camera will restart in merely 30 sec.
4. APP operation.
1. Peer-to-peer connection of the mobile phone to the camera
Enter the WI-FI signal option of the mobile settings, find the camera's signal (the
signal refers to the camera's UID/model, unique to each camera) and connect it. It is
as shown in the picture
Open the mobile APP (LOOKCAMPro), enter the camera, as shown in the following
picture.
2. Remotely set the camera as follows
(select the WiFi network to be connected, enter the password (it must be correct) and
complete, then wait till the camera completes its restart, which takes about 40 sec.
The camera will become online from the offline status, at that point the indicator will
be permanently on in blue light. Upon successful connection, online video can be
viewed remotely. (default password is 6666)
5. Specification and parameters
Resolution Ratio 4K/2K/1080P/720P
Video Format MP4
Frame Number 25
Visual Angle 90/150 degree
Motion Detection Camera Straight line 6 --10meters
Shooting
Minimal Illumination 1LUX
Video Duration Over 1 Hours
Compressed Format H.264
Recording Range 5㎡
Consumption 380MA/3.7V
Storage Temperature -20-80 degree centigrade
Operating Temperature -10-60 degree centigrade
Operation Humidity 15-85%RH
Memory Card Type TF card
Player Software VLCPlayer/SMPlayer
Mobile Phone Operating Android/iOS
System
Q&A.
1. Remote surveillance is lagging. Please select the appropriate video resolution
according to the actual network environment.
2. SD card storage failure or failure in memory card reading. Before using the SD
card for the first time, the SD card must be formatted.
3. Failure of network connection. After resetting, please first connect the wifi signal
of the camera before further configuration. The camera network supports 2.4G WiFi
but not 5.8G WiFi, so please select the correct connection method.
4. APP remote view of SD card videos is lagging. The decoding capacity of
different mobiles is varied. Please adjust the camera's recording to the resolution
appropriate to your mobile phone.
5. I forget the password. Please press and hold the reset key of the camera for 5 sec
to restore the factory setting.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecti
on against harmful interference in a residential installation. This equipment generates, uses an
d can radiate radio frequency energy and, if not installed and used in accordance with the instru
ctions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is e
ncouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two co
nditions: (1) This device may not cause harmful interference, and (2) this device must accept an
y interference received, including interference that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible for compliance co
uld void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment must be installed and operated in accordance with provided instructions and the
antenna(s) used for this transmitter must be installed to provide a separation distance of at least
20 cm from all persons and must not be co-located or operating in conjunction with any other ant
enna or transmitter. End-users and installers must be provide with antenna installation instructio
ns and transmitter operating conditions for satisfying RF exposure com
