COLOR TELEVISION RECEIVER

Chassis : K15A
Model : CM19001X/KMT

COLOR TELEVISION RECEIVER CONTENTS

1. Precautions

2. Specifications

3. Disassembly and Reassembly

4. Alignment and Adjustments

5. Troubleshooting

6. Exploded Views and Parts List

7. Electric Parts List

8. Block Diagram

9. PCB Layout

10. Wiring Diagrams

11. Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd.DEC. 2001

Printed in Korea
AA81-00063A
 Precautions

1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.

1-1 Safety Precautions

1. Be sure that all of the built-in protective

devices are replaced. Restore any missing (READING SHOULD
NOT BE ABOVE
protective shields. DEVICE
LEAKAGE
CURRENT 0.5mA)
UNDER TESTER
TEST
2. When reinstalling the chassis and its TEST ALL
assemblies, be sure to restore all protective EXPOSED METAL
SURFACES
devices, including: nonmetallic control knobs
2-WIRE CORD
and compartment covers.
ALSO TEST WITH
PLUG REVERSED
3. Make sure that there are no cabinet openings (USING AC ADAPTER EARTH
PLUG AS REQUIRED) GROUND
through which peopleÑparticularly
childrenÑmight insert fingers and contact
dangerous voltages. Such openings include
Fig. 1-1 AC Leakage Test
the spacing between the picture tube and the
cabinet mask, excessively wide cabinet
6. Antenna Cold Check:
ventilation slots, and improperly fitted back
With the unitÕs AC plug disconnected from the
covers.
AC source, connect an electrical jumper across
the two AC prongs. Connect one lead of the
If the measured resistance is less than 1.0
ohmmeter to an AC prong. Connect the other
megohm or greater than 5.2 megohms, an
lead to the coaxial connector.
abnormality exists that must be corrected
before the unit is returned to the customer.
7. X-ray Limits:
The picture tube is especially designed to pro-
4. Leakage Current Hot Check (Figure 1-1):
hibit X-ray emissions. To ensure continued
Warning: Do not use an isolation
X-ray protection, replace the picture tube only
transformer during this test. Use a leakage-
with one that is the same type as the original.
current tester or a metering system that
Carefully reinstall the picture tube shields and
complies with American National Standards
mounting hardware; these also provide X-ray
Institute (ANIS C101.1, Leakage Current for
protection.
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
8. High Voltage Limits:
High voltage must be measured each time ser-
5. With the unit completely reassembled, plug
vicing is done on the B+, horizontal deflection
the AC line cord directly into the power
or high voltage circuits. Correct operation of
outlet. With the unitÕs AC switch first in the
the X-ray protection circuits must be
ON position and then OFF, measure the
reconfirmed whenever they are serviced.
current between a known earth ground (metal
(X-ray protection circuits also may be called
water pipe, conduit, etc.) and all exposed
Òhorizontal disableÓ or Òhold-downÓ.)
metal parts, including: antennas, handle
brackets, metal cabinets, screwheads and
Heed the high voltage limits. These include
control shafts. The current measured should
the XÐray Protection Specifications Label, and
not exceed 0.5 milliamp. Reverse the power-
the Product Safety and X-ray Warning Note on
plug prongs in the AC outlet and repeat the
the service data schematic.
test.

Samsung Electronics 1-1

Precautions

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified 15. Observe the original lead dress, especially
limits by close-tolerance, safety-related near the following areas: Antenna wiring,
components and adjustments. If the high sharp edges, and especially the AC and high
voltage exceeds the specified limits, check voltage power supplies. Always inspect for
each of the special components. pinched, out-of-place, or frayed wiring. Do
not change the spacing between components
10. Design Alteration Warning: and the printed circuit board. Check the AC
Never alter or add to the mechanical or power cord for damage. Make sure that leads
electrical design of this unit. Example: Do not and components do not touch thermally hot
add auxiliary audio or video connectors. Such parts.
alterations might create a safety hazard. Also,
any design changes or additions will void the 16. Picture Tube Implosion Warning:
manufacturerÕs warranty. The picture tube in this receiver employs
Òintegral implosionÓ protection. To ensure
11. Hot Chassis Warning: continued implosion protection, make sure
Some TV receiver chassis are electrically that the replacement picture tube is the same
connected directly to one conductor of the AC as the original.
power cord. If an isolation transformer is not
used, these units may be safely serviced only 17. Do not remove, install or handle the picture
if the AC power plug is inserted so that the tube without first putting on shatterproof
chassis is connected to the ground side of the goggles equipped with side shields. Never
AC source. handle the picture tube by its neck. Some
Òin-lineÓ picture tubes are equipped with a
To confirm that the AC power plug is inserted permanently attached deflection yoke; do not
correctly, do the following: Using an AC try to remove such Òpermanently attachedÓ
voltmeter, measure the voltage between the yokes from the picture tube.
chassis and a known earth ground. If the
reading is greater than 1.0V, remove the AC 18. Product Safety Notice:
power plug, reverse its polarity and reinsert. Some electrical and mechanical parts have
Re-measure the voltage between the chassis special safety-related characteristics which
and ground. might not be obvious from visual inspection.
These safety features and the protection they
12. Some TV chassis are designed to operate with give might be lost if the replacement compo-
85 volts AC between chassis and ground, nent differs from the originalÑeven if the
regardless of the AC plug polarity. These units replacement is rated for higher voltage,
can be safely serviced only if an isolation wattage, etc.
transformer inserted between the receiver and
the power source. Components that are critical for safety are
indicated in the circuit diagram by shading,
13. Some TV chassis have a secondary ground ( ) or ( ! ).
system in addition to the main chassis ground. Use replacement components that have the
This secondary ground system is not same ratings, especially for flame resistance
isolated from the AC power line. The two and dielectric strength specifications.
ground systems are electrically separated by A replacement part that does not have the
insulating material that must not be defeated same safety characteristics as the original
or altered. might create shock, fire or other hazards.

14. Components, parts and wiring that appear to

have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or overheat-
ing, and correct any potential hazards.

1-2 Samsung Electronics

 Precautions

1-2 Servicing Precautions

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between
the servicing and safety precautions, always follow the safety precautions.
Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the 5. Check the insulation between the blades of the
cabinet. Follow them. AC plug and accessible conductive parts
(examples: metal panels, input terminals and
2. Always unplug the unitÕs AC power cord from earphone jacks).
the AC power source before attempting to: (a)
Remove or reinstall any component or 6. Insulation Checking Procedure: Disconnect the
assembly, (b) Disconnect an electrical plug or power cord from the AC source and turn the
connector, (c) Connect a test component in power switch ON. Connect an insulation
parallel with an electrolytic capacitor. resistance meter (500V) to the blades of the AC
plug.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or The insulation resistance between each blade
tape is sometimes used. The internal wiring is of the AC plug and accessible conductive parts
sometimes clamped to prevent contact with (see above) should be greater than 1 megohm.
thermally hot components. Reinstall all such
elements to their original position. 7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
4. After servicing, always check that the screws, its assemblies) unless all solid-state heat sinks
components and wiring have been correctly are correctly installed.
reinstalled. Make sure that the portion around
the serviced part has not been damaged. 8. Always connect a test instrumentÕs ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrumentÕs ground lead last.

Samsung Electronics 1-3

Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (Òsolid stateÓ) devices 5. Use only a grounded-tip soldering iron when
are easily damaged by static electricity. Such soldering or unsoldering ESDs.
components are called Electrostatically
Sensitive Devices (ESDs); examples include 6. Use only an anti-static solder removal device.
integrated circuits and some field-effect Many solder removal devices are not rated as
transistors. The following techniques will Òanti-staticÓ; these can accumulate sufficient
reduce the occurrence of component damage electrical charge to damage ESDs.
caused by static electricity.
7. Do not remove a replacement ESD from its
2. Immediately before handling any semicon protective package until you are ready to
ductor components or assemblies, drain the install it. Most replacement ESDs are
electrostatic charge from your body by packaged with leads that are electrically
touching a known earth ground. Alternatively, shorted together by conductive foam,
wear a discharging wrist-strap device. (Be aluminum foil or other conductive materials.
sure to remove it prior to applying powerÑ
this is an electric shock precaution.) 8. Immediately before removing the protective
material from the leads of a replacement ESD,
3. After removing an ESD-equipped assembly, touch the protective material to the chassis or
place it on a conductive surface such as circuit assembly into which the device will be
aluminum foil to prevent accumulation of installed.
electrostatic charge.
9. Minimize body motions when handling
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such
can generate electrical charges that damage as brushing clothes together, or lifting a foot
ESDs. from a carpeted floor can generate enough
static electricity to damage an ESD.

1-4 Samsung Electronics

 Specifications

2. Specifications

2-1 Specifications

Television System 14"/20"/21" NTSC COLOR TV SIGNAL

Power Consumption 14" : 57 WATTS NOMINAL,

20" : 70 WATTS NOMINAL
21" : 75 WATTS NOMINAL,

Picture Tube 14" : A34KQV42X

20" : A48KRD82X (H)
21": : A51KQJ63X (H)

Power Requirement AC 120V, 60Hz /AC 100 ~ 240, 50Hz, 60Hz

Operating System REMOCON SYSTEM (SZM354ET)

Tuning Ranges VHF CH : 2-13, UHF CH : 14-69, CABLE CH : 1,14-125

Antenna Input Impedance 75 ohm UNBALANCED TYPE FOR VHF/UHF

Intermediate Frequency PICTURE 45.75MHz, SOUND 41.25MHz,

COLOR SUB CARRIER 42.17MHz

Speaker Impedance Single: 8 ohm 3W

Dual : 8 ohm 3W x 2
Dual : 16 ohm , 3W x 2 (CT-33H1, CT-50H1)

Samsung Electronics 2-1

 Disassembly and Reassembly

3. Disassembly and Reassembly

3-1 Back Cover Removeal

Fig. 3-1

1. After removing the screws, pull the cabinet backwards.

Samsung Electronics 3-1

Disassembly and Reassembly

3-2 Main Board Removal

Fig. 3-2 Fig. 3-3

1. Separate the socket board from the CRT neck.

2. Remove the Anode Cap from the CRT.

3. Remove the main board by pulling it with both hands.

Warning: The FBT is charged with high voltage.

Before removing the Anode Cap, discharge the voltage
through one of the heat sinks on the main board.

3-2 Samsung Electronics

 Disassembly and Reassembly

3-3 Speaker Removal

1. Loosen the screws and remove the speakers.

Fig. 3-4

Samsung Electronics 3-3

Disassembly and Reassembly

3-4 CRT Removel

Fig. 3-5

1. Spread a soft mat on the floor. Place the TV set face down.

2. Remove the 4 nuts mounting the CRT to the front cabinet.

3. Lift the CRT.

4. Caution: Because of the high vacuum and large surface area of the
picture tube, be careful while handling it:
(1) Always lift the picture tube by grasping it firmly around the face-
plate, (2) Never lift the tube by its neck. (3) Do not scratch the picture
tube or apply excessive pressure. Fractures of the glass may cause an
implosion.

3-4 Samsung Electronics

 Alignment and Adjustments

4. Alignment and Adjustments

4-1 Service Mode Adjustments

4-1-1 Service Mode Menus

Since there are no VRs in the K15A chassis, all

adjustments after parts replacement must be
done in the Service Mode. Service Mode
adjustments are necessary when either the
EEPROM (IC902) or the CRT is replaced.

4-1-2 Entering the Service Mode

Press the following transmitter keys

while in STAND-BY mode:

MUTE—>1—>8—>2—>POWER
“Factory Mode Menu” is displayed Change the data with “Volume +, - “ keys.

ADJUSTMENT <---selected (violet)

VCO 71
PATTERN
OPTION
RESET

Enter Service Mode using the Volume Return to the Service mode by pressing
+,- keys. Service Mode Menu: MENU.

AGC XX RC XXX AGC XX RC XXX

VCO XX GC XXX VCO XX GC XXX
SBT XX BC XX SBT XX BC XX
SCT XX VA XX SCT XX VA XX
SCR XX VS XX SCR XX VS XX
STT XXX HS XX STT XXX HS XX
GG XXX SS XX GG XXX SS XX
BG XXX SVC : MUTE BG XXX SVC : MUTE

Select a mode to be adjusted, using the chan- Return to the Factory mode via the MENU
nel down key. Example: VCO. key.

AGC XX RC XXX ADJUSTMENT

VCO XX GC XXX PATTERN
OPTION
SBT XX BC XX
RESET
SCT XX VA XX
SCR XX VS XX Press POWER to enter the Stand-by mode.
STT XXX HS XX
GG XXX SS XX
BG XXX SVC : MUTE

Samsung Electronics 4-1

Alignment and Adjustments

4-1-3 Adjustment in Option Mode 4-1-4 Service Mode Adjustments

This adjustment is necessary whenever the

EEPROM is replaced. Input data (as marked
ADJUSTMENT
on the back cabinet).
PATTERN
ADJUSTMENT OPTION
PATTERN RESET
OPTION
RESET 1. The Pattern Adjustment is done only in the
factory. Do not attempt to readjust it.
Select “SET OPTION” by pressing the
Channel ▼ key twice. 2. Refer to 4-2 for other adjustments.

ADJUSTMENT 3. Set OPTION data.

PATTERN
OPTION
RESET

Press the Volume +, - keys to enter the set 4-1-5 Service Mode Adjustment Ratings
Option mode.
Initalized
No Item Function Range MICOM Data
BYTE 0 : 0 0
1 AGC RF AGC Adjustment 0~63 50

Press MENU to go back to the factory mode. 2 VCO PIF VCO Adjustment 0~127 63

3 SCT SUB-CONTRAST Adjustment 0~63 48

ADJUSTMENT
PATTERN 4 SCR SUB-COLOR Adjustment 0~27 13
OPTION 5 STT SUB-TINT Adjustment 0~27 7
RESET
6 RC RED-CUT OFF Adjustment 0~255 0

7 GC GREEN-CUT OFF Adjustment 0~255 0

Select RESET with channel ▼ key. 8 BC BLUE-CUT OFF Adjustment 0~255 0

9 SVC Input a Horiz line pattern

ADJUSTMENT
PATTERN 10 GG GREEN-GAIN Adjustment 0~255 127
OPTION 11 BG BLUE-GAIN Adjustment 0~255 127
RESET
12 SBT SUB-BRIGHTNESS Adjustment 0~63 31

13 VA VERTICAL SIZE Adjustment 0~63 39

Press volume + key.
14 VS VERTICAL CENTER Adjustment 0 0
POWER 15 HS HORIZONTAL Phase Adjustment 0~31 15
OFF
16 SS SUB-SHARPNESS Adjustment 0~31 4

Note : The initial MICOM data values take

effect when IC902 is replaced.

4-2 Samsung Electronics

 Alignment and Adjustments

4-2 Alignment and Adjustment

4-2-1 General Alignment Instructions 4-2-5 IC902 Replacement

1. Usually, a color TV needs only slight
1. When IC902 is replaced, all values are reset to
touch-up adjustment upon installation. Check
“Initialized MICOM Data” and readjustment
the basic characteristics such as picture height,
is necessary.
focus and a horizontal and vertical sync.
2. Press the POWER button 10 seconds after
2. Observe the picture and check for good back
plug-in.
and white details. There should be no
objectionable color shading: If color shading is
3. To enter the Service Mode, refer to Fig. 4-1
present, demagnetize the receiver. If color
(Service Mode Adjustment).
shading persists, perform purity and
convergence adjustments described below.

3. To protect against shock hazard, use an

4-2-6 PIF VCO Adjustment
isolation transformer.
1. Use a Pattern Generator or an off-air signal.
4-2-2 Power Supply Check
2. Open pin 11 of Micom (IC901) or one side of
lead pin for R237.
Check the following:
A: Power plug is connected; “Stand-by” mode
3. Adjust VCO in the service mode to set IC101
B: Power On when “Power ON” button is pressed
Pin 44 (AFT) to 2.5V ± 0.4V.
C: Power On by FBT Each supply is marked on
its lead-in wire. ( )
4. Connect the opened site.

4-2-3 Focus Adjustment

4-2-7 RF-AGC Adjustment
Adjust the focus control on the FBT for well
defined scanning lines.
1. Input a PHILLIPS pattern.

4-2-4 Fail Safe Circuit Check (FS) (OPTION) 2. Set the input signal to 60 dB.

1. The failsafe check must be the final step in 3. Enter into the AGC in the service mode.
servicing.
4. Adjust AGC until color bar noise disappears.
2. Turn the power switch ON and adjust
customer controls for normal operation.

3. Temporarily short pin X to pin R on the main

board (RX06, RX04) with a jumper wire.
Raster will disappear.

4. The TV must remain in this state even after

removing the jumper wire. This shows that
the failsafe circuit is working properly.

5. To recover picture and sound, temporarily

turn off the TV and allow the failsafe circuit
more than 30 seconds to reset. Then switch
power ON to produce normal picture and
sound.

Samsung Electronics 4-3

Alignment and Adjustments

4-2-8 Sub-Contrast Adjustment 4-2-10 Sub-Color Adjustment

1. Input a gray scale pattern. Use a pattern 1. Do sub-color adjustment after the Sub-
generator (PM5518). Contrast and Sub-Tint adjustments.

2. Short D208 to switch off the ABL feed-back. 2. D208 should still be shorted. The ABL should
still be switched OFF.
3. Check CN201 R-OUT with an oscilloscope.
3. Input a color bar pattern. Use a pattern gen-
4. Set RC, BC, GC data to 0 in the Service Mode. erator (PM5518).

5. Adjust SCT to 2.40 ± 0.1Vp-p 4. Check CN201 R-OUT (use an oscilloscope).

5. Ensure that the RC, GC and BC data are 0.

BG are 140 and GG should be 90.

6. Adjust SCR to 2.4 ± 0.1Vp-p (black and

red levels).
2.5V_+ 0.1Vpp
7. Remove the short across D208 and restore
ABL.

6. Remove the short across D208 and restore

ABL.
2.4V _+ 0.1Vpp

4-2-9 Sub-Tint Adjustment

1. Input a rainbow pattern.

2. Check CN201 B-OUT with an oscilloscope.

3. Adjust STT in the service mode until the 6th

peak is the highest and the 5th and 7th peaks
have equal heights.

6
5 7 8
4
3 9
2 10
1

4-4 Samsung Electronics

 Alignment and Adjustments

4-2-11 White Balance Adjustment 4-2-13 Vertical Size Adjustment

1. Input a lion head pattern.

4-2-11 (A) LOW-LIGHT ADJUSTMENTS
2. After the vertical center adjustment, enter into
1. Input either a lion head or “pure white” color the service mode.
pattern.
3. Adjust VA so that the each top and bottom of
2. Operate the receiver for 30 minutes. the screen is 4.0. If the top and bottom values
are different, adjust VA so that the sum of the
3. Check the data in the service mode: two values is 8.0.
RC, GC, BC are 0 and SB is 16;
Steps BG are 90 and GG are 140.
4-2-14 Horizontal Size Adjustment
4. Enter the horizontal line mode by pressing
the MUTE key. 1. Receive a lion head pattern.

5. Adjust the screen VR on the FBT until a dim 2. Enter into the service mode.
colored line (red,green or blue) appears on the
screen. 3. Adjust HS to symmetrized right and left.

6. After pressing the MUTE key, go to RC,BC or

▼
GC with channel , ▼ keys. After putting a 4-2-15 When CRT Is Replaced
dim colored line (red, green or blue) in the
horizontal line with MUTE key, adjust color Do the following adjustments after the basic
▼
with volume ,▼ keys. purity and convergence adjustments.

7. Exit the horizontal line via the MUTE key. 1. White Balance

2. Sub-brightness
4-2-11 (B) HIGH-LIGHT ADJUSTMENTS
3. Vertical Size
1. Input a high-light pattern
4. Horizontal Size
2. Adjust GG,BG in the Service Mode.
5. Fail safe (should be the final step).
3. Recheck in low light.

4-2-12 Sub-Brightness Adjustment

1. Input a Toshiba pattern.

2. Warm up the receiver for 10 minutes.

3. Enter the Service Mode and set SB to the point

where the 5th point is brighter in the gray
scale.

5 4 3 2 1

Samsung Electronics 4-5

 MEMO

4-6 Samsung Electronics

 Troubleshooting

5. Troubleshooting

5-1 No Power

No Power

OFF ON
Check LED when AC Check IC802.
code is plugged.
Abnormal

Abnormal Check Normal

Check/Replace
Fuse. IC802, R812, D856.

Check and Replace Check

D807 ~D810 IC801* Pin 1
Oscillation.

Abnormal

Abnormal (0 ~ 15V) Check

IC801 Pin 3 B+.

Check/Replace
D806, Q401, Q801, Normal (15~20V)
D802, D814*

Abnormal (0V) Check IC801* Normal (0.5 ~ 3V)

Pin 4 Voltage

Check/Replace Check/Replace
PC802, DZ807 DZ802, DZ803, D806

Samsung Electronics 5-1

Troubleshooting

5-2 No Sound

No Sound

Check
Normal Connector CN601 Abnormal
and CN701.

Check
Abnormal Waveform of Normal Check CN601 and CN701
IC601 Pin 1. Connector
Soldering and A/V PCB.

Check Abnormal Check

Normal Normal
Waveform of IC201 Waveform of IC601 and Ok
Pin 52. IC602 Pins 4.

Abnormal
Check Normal
Waveform of IC201
Pin 1. Check Normal (approx. 12V)
Voltage of IC601 and IC602
Pin 5.
Abnormal
Abnormal
Check
Volume O.K
SIF (L201).
Up. Check Power Replace IC601
12V Line Voltage. and IC602.
NG

Check/Replace
IC201.

5-2 Samsung Electronics

 Troubleshooting

5-3 Horizontal Line Appears

Single Horizontal Line

Normal (24V) Check Abnormal

24V-C Voltage.

Check Check
Abnormal NG
Waveform of IC201 FBT Pin 2 (24V)
Pins 22,24. Oscillation.

Normal
Check Whether O.K
a horizontal line appears in Normal
the service mode.. Check R409 Check/Replace
Open. FBT.

NG Open

Check/Replace Check/Replace Check/Replace

IC201. IC301. R409.

Samsung Electronics 5-3

Troubleshooting

5-4 No Signal

No Signal

Abnormal Check
each tuner terminal Normal
voltage.

Check voltage Check

Abnormal tuner SCL,SDA Normal
line.
waveform.

Normal Check
Check tuner IF terminal
Micom IC901. waveform.

Abnormal
Check
IC201 Pins 7,8
waveform.
Replace tuner.

Normal
Check IC201 Pin 41
waveform level.
Check
whether AGC and Abnormal
Normal (2Vp-p) AFTadjustment are normal in
the service mode.

Check Normal
IC201 Pin 43 waveform
level. Readjust AGC
Check and AFT.
Abnormal IC201 Pin 47
Normal (1Vp-p) waveform level.

Check Normal (2Vp-p)

Abnormal IC201 Pins 19,20, 21
waveform level.
Check IC201
Normal (3~5Vp-p) Pin 37 waveform
level.

Replace IC201. Check CRT PCB (180V)

and heater Voltages. Normal (1Vp-p)

5-4 Samsung Electronics

 Exploded Views & Parts List

6. Exploded Views & Parts List

6-1 CM19001X/KMT

No Code No Description;Specification Q’ty Remark

1 AA92-30161J ASSY-CABINET,FRONT;CM19001X,20F2R1-HIPS 1 A/FRNT
AA64-00150B CABINET-FRONT;-,20R1,BK708P EGH,HIPS,VO, 1 F/C
1-1 BADGE BRAND 1 BADGE
1-2 KNOB POWER 1 KP
1-3 SPRING-CS 1 SPRING
1-4 AA61-40113A STOPPER-PCB;-,ABS,HB,NTR. 1 STOPER
1-5 AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL 1 CLW/HS
1-6 INDICATOR-LED 1 IL
1-7 WINDOW REMOCON 1 WR
1-8 SCREW-TAPTITE 1 WR+CF
1-9 KNOB-CONTROL 1 KC
1-10 SCREW-TAPTITE 1 KC+CF
1-11 6002-000512 SCREW-TAPPING;RH,+,2,M4,L12,ZP 2 SPK+CF
1-12 AA96-10141A ASSY-SPEAKER;3W,8OHMX1,700 1 A/SPK

2 AA03-10029W CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT. 1 CRT

2-1 AA27-20004B COIL-DEGAUSSING;-,20,5.7ohm,30T,L2170,E 1 D-COIL
2-2 AA60-10050R SCREW-ASSY;WC,HH,+M5,L31.5,SWR 4 CRT+CF
2-3 3704-001090 SOCKET-CRT;9P,15.24PI,26.5PI,SN 1 V999

3 AA64-00154B CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,- 1 B/C

3-1 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR 4 CB+CF

4 AA96-20129A ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P, 1 PWR/AC

Samsung Electronics 6-1

 MEMO

6-2 Samsung Electronics

 Electric Parts List

7. Electric Parts List

7-1 CM19001X/KMT

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

ASSY-PCB,MAIN(COM) 3
3
D809
D808
0402-001111
0402-001111
DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
3 D807 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
1 A/MAIN AA94-10133T ASSY-PCB,MAIN(COM);CM19001X/KMT 3 D805 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20
3 D814 0402-000534 DIODE-RECTIFIER;RG10V,400V,1.5
2 A/SUBM AA97-01633A ASSY-SUB MATERIAL;SOLVENTES Y SOLDADURAS 3 D802 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5
3 0204-000442 SOLVENT;CH3-CH5H-CH396%IM-1000 3 D803 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
3 0202-000008 SOLDER-WIRE;S63S-D3.0,S63A,D3,63/37 3 D405 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
3 0204-001024 FLUX;DF-96TVS,-,20%,- 3 D301 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
3 0202-000187 SOLDER-WIREFLUX;-,RS60S,D1.2,6 3 D403 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
2 Q601 0502-000242 TR-POWER;KSA614,PNP,-80V,-55V, 3 D404 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,40
2 Q401 0502-001115 TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8 3 DZ806 0403-001318 DIODE-ZENER;MTZJ4.3B,4.17-4.43V,500mW,DO
2 PC802 0604-001038 PHOTOCOUPLER;TR,130-260%,200MW 3 DZ903 0403-001319 DIODE-ZENER;MTZJ4.7C,4.68-4.93V,500mW,DO
2 IC902 1103-001107 IC-EEPROM;24C020,256X8BIT,DIP,8P,300MIL 3 D205 0403-001319 DIODE-ZENER;MTZJ4.7C,4.68-4.93V,500mW,DO
2 IC802 1203-000576 IC-S/WREGU;TDA8139SIP7POUT-9.5 3 D906 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 IC201 1204-001259 IC-VIDEOSYSTEM;TA1282N,DIP,56P 3 DZ803 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 C804 2201-000446 C-CERAMIC,AC;CK45PE400V332-M(T 3 DZ901 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 C801 2401-000818 C-ELECTROLYTIC;CE04W200V220M 3 DZ902 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 X901* 2801-003224 CRYSTAL-UNIT;32.768KHZ,20PPM,2 3 D905 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 X202 2802-000172 RESONATOR-CERAMIC;503.5KHZ,0.5 3 D102 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 V999 3704-001090 SOCKET-CRT;9P,15.24PI,26.5PI,SN 3 D855 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 CN603 3711-002642 POST-HEADER;67094-003(AUTO) 3 D856 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 JA701 3722-000162 JACK-PIN;2P,3.4MM,-,SN 3 D902 0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
2 IC901 AA13-30020A IC-MCU;-,Z8933412PSC-R3757,16BIT,SDIP 3 DZ807 0403-000510 DIODE-ZENER;MTZJ6.2B,6.2V,5.96-6.27V,500
2 L205* AA26-10004C TRANS-IF;-,7MG,VIF,0.37UH,7MM, 3 DX01 0403-000510 DIODE-ZENER;MTZJ6.2B,6.2V,5.96-6.27V,500
2 L201 AA26-10004K TRANS-IF;-,7MG,SIF,-,7MM,100PF 3 DZ802 0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO
2 T801 AA26-20007L TRANS-SWITCHING;120V,125/12.5,UL/CSA,EAE 3 D704 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
2 T401 AA26-50001B HORIZ.DRIVE;-,7.1MH,102UH,10-2 3 D701 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
2 L401 AA27-30001B COIL-LINEARITY;-,195UH,QIC1010 3 D210 0403-000720 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500
2 L801 AA29-30002F FILTER-LINENOISE;-,6MH,2.45A,- 3 D302 0403-001211 DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D
2 CN501 AA39-20109A LEAD-CONNECTOR,ASSY;-,YBNH025- 3 D299 0403-001211 DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D
2 TU01 AA40-00045A TUNER-F/S;TECC1070PG32A(S),NTSC,TR,181CH 3 D804 0403-001211 DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D
2 RM901 AA32-00008A MODULE REMOCON;SRV-19M,38KHZ,800,MESH,V, 3 D201 0403-001316 DIODE-ZENER;MTZJ3.0A,2.85-3.07V,500mW,DO
2 L/PQS AA68-01018A LABEL-PQS,-,50mmX,13,-,WHITE,- 3 D101 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,
2 T444 AA26-30001Y TRANS-FRYBACK;-,FSV-20A001,20,125V 3 QX01 0501-000283 TRANSISTOR;KSA539-Y(TAPG)/YTAM
2 IC601 AA96-50410B ASSY-H/S;LA62-30191B,LA4425 3 Q402 0501-000369 TRANSISTOR;KSC2331-Y(TAPG)
3 1201-001298 IC-POWER AMP;4425,SIP,5P,9.5MIL,MONO,45D 3 Q151 0501-000436 TR-SMALLSIGNAL;KTC3197,NPN,30V
3 6006-001035 SCREW-ASSY,MAC;WSP,PH,3ML8ZPC,YEL 3 Q503 0501-002014 TR-SMALLSIGNAL;KSC2330-RNPN
3 AA62-30191B HEAT-SINK,PS;-,SPC-1,T1.0,-,LA4425,-,FP- 3 Q502 0501-002014 TR-SMALLSIGNAL;KSC2330-RNPN
3 6021-000222 NUT-HEXAGON;2C,M3,ZPC(YEL),SM20C1 3 Q501 0501-002014 TR-SMALLSIGNAL;KSC2330-RNPN
2 IC801 AA96-50395A ASSY-H/S;-,-,AA62-30190A,KA3S0765R,- 3 Q903 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
3 1203-001493 IC-PEM CONTROLLER;3S0765RF,TO3PF-5L,5,21 3 Q602 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
3 AA62-30190A -,SECC-CA,T1.0,-,-,-,Cr03 A 3 Q203 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
3 AA61-11028A BRACKET-IC;SECC,T1.0,-, 3 Q202 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
3 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP 3 Q201 0501-002183 TR-SMALL SIG;KTC9014,NPN,625MW,TO-92,100
2 IC301 AA96-50075A ASSY-H/S;-,VERT,AA62-30032A,KA2131 3 QU01 0504-000123 TR-DIGITAL;KSR1010,NPN,300MW,1
3 1204-000475 IC;KA2131 3 DZ801 1405-000152 VARISTOR;560V,2500A,14X8.5MM,T
3 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZP 3 R302 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,
3 AA62-30032A HEAT SINK-PS/-,SPC-1,T1.0-,FT-2V- 3 R503 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
2 PWR/AC AA96-20129A ASSY-POWER,CORD;-,EP2/YES,H/C300,ME301P, 3 R502 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
3 AA39-10007Y POWER-CORD;-,EP2/YES,SPT-2 18AWGx2C,2.4m 3 R501 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
3 AA61-20284A HOLDER P CORD;PP,VO,BLK,KE-002 3 R159 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
2 A/AUTO AA94-05248A ASSY-PCB,MAIN(AUTO);K15A(C),19,S/V KMT 3 R158 2001-000007 R-CARBON;3KOHM,5%,1/8W,AA,TP,1
3 D904 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R926 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
3 D903 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R822 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,T
3 D806 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R416 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,T
3 D601 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R702 2001-000085 R-CARBON(S);100KOHM,5%,1/2W,AA
3 D207 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R242 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
3 D202 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R206 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
3 D203 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R205 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
3 D204 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R204 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
3 D206 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R152 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP
3 D901 0401-000005 DIODE;1N4148,100V,300mA,,1V,8nS,TAPING 3 R929 2001-000232 R-CARBON;1.3KOHM,5%,1/8W,AA,TP
3 DX02 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 3 R908 2001-000232 R-CARBON;1.3KOHM,5%,1/8W,AA,TP
3 D402 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 3 R228 2001-000258 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m
3 D401 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 3 R229 2001-000258 R-CARBON;1.8Kohm,5%,1/8W,AA,TP,1.8x3.2m
3 D208 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 3 R235 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP
3 D103 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 3 R509 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,
3 D810 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20

7-1
Electric Parts List

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

3 R903 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R401 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm

3 R904 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R223 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R922 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R154 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R923 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R603 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,
3 R155 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R602 2001-000786 R-CARBON;47KOHM,5%,1/8W,AA,TP,
3 R211 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R156 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1
3 R212 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R901 2001-000793 R-CARBON;47OHM,5%,1/8W,AA,TP,1
3 R507 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 RX08 2001-000837 R-CARBON;51KOHM,5%,1/8W,AA,TP,
3 R508 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP, 3 R213 2001-000837 R-CARBON;51KOHM,5%,1/8W,AA,TP,
3 R930 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R907 2001-000995 R-CARBON;820OHM,5%,1/8W,AA,TP,
3 R932 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R910 2001-000995 R-CARBON;820OHM,5%,1/8W,AA,TP,
3 R933 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R853 2001-001054 R-CARBON(S);1.6KOHM,5%,1/2W,AB,TP,2.4X6.
3 R937 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 RU07 2001-001062 R-CARBON(S);10MOHM,5%,1/2W,AA,
3 R927 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R806 2001-001071 R-CARBON(S);12KOHM,5%,1/2W,AA,
3 R237 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R807 2001-001071 R-CARBON(S);12KOHM,5%,1/2W,AA,
3 R605 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R615 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4
3 R911 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R852 2001-001088 R-CARBON(S);1KOHM,5%,1/2W,AA,TP,2.4X6.4
3 R921 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R444 2001-001099 R-CARBON/METALFILM;RD1/2T2.7K-
3 R916 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R207 2001-001111 R-CARBON(S);240OHM,5%,1/2W,AA,
3 R917 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R403 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,
3 R918 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP, 3 R824 2001-001125 R-CARBON(S);300KOHM,5%,1/2W,AA
3 R215 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP, 3 R404 2001-001136 R-CARBON(S);36OHM,5%,1/2W,AA,T
3 R214 2001-000331 R-CARBON;12KOHM,5%,1/8W,AA,TP, 3 R808 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA
3 RU06 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP 3 R801 2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA
3 RX01 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP 3 R614 2001-001152 R-CARBON/METALFILM;RD1/2T47K-J
3 R234 2001-000405 R-CARBON;180OHM,5%,1/8W,AA,TP, 3 R823 2001-001178 R-CARBON(S);680OHM,5%,1/2W,AA,
3 RX02 2001-000411 R-CARBON;18KOHM,5%,1/8W,AA,TP, 3 R701 2001-001187 R-CARBON(S);75OHM,5%,1/2W,AA,T
3 R931 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 R417 2001-001410 R-CARBON;RD1/2T(S)430-J43R
3 R902 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 R515 2002-001006 R-COMPOSITION;4.7KOhm,5%,1/2W,AA,TP,3.7X
3 R611 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 RH01 2002-001006 R-COMPOSITION;4.7KOhm,5%,1/2W,AA,TP,3.7X
3 R301 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 RH02 2002-001006 R-COMPOSITION;4.7KOhm,5%,1/2W,AA,TP,3.7X
3 R241 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 RU01 2002-001010 R-COMPOSITION;1.8MOHM,5%,1/2W,AA,TP,3.7X
3 R201 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 R805 2002-001013 R-COMPOSITION;4.7MOhm,5%,1/2W,AA,TP,3.7X
3 R905 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 R304 2003-000436 R-METALOXIDE(S);1.5OHM,5%,1W,A
3 R938 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 R405 2003-000540 R-METALOXIDE(S);1KOHM,5%,2W,AD
3 R230 2001-000429 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm 3 R504 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
3 R925 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP 3 R504A 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
3 R924 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP 3 R505 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
3 R604 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP 3 R505A 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
3 R952 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 3 R506 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
3 R906 2001-000472 R-CARBON;2.7KOHM,5%,1/8W,AA,TP 3 R506A 2003-000784 R-METAL OXIDE(S);7.5KOHM,5%,2W,AF,TP,3.7
3 R227 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP 3 R407 2003-000994 R-METALOXIDE(S);33KOHM,5%,2W,AF,TP,3.9X1
3 R226 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP 3 R309 2003-001043 R-METALOXIDE(S);510OHM,5%,1W,A
3 R988 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP 3 R802 2003-002119 R-METAL OXIDE(S);36KOHM,5%,1W,AF,TP,2.5X
3 R402 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP, 3 R928 2001-000864 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R210 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP, 3 RU10 2001-000924 R-CARBON;680ohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R209 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP, 3 R305 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
3 R208 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP, 3 R239 2001-000947 R-CARBON;7.5KOHM,5%,1/8W,AA,TP
3 RX05 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP, 3 R233 2001-000011 R-CARBON;75Kohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R920 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP, 3 R919 2001-000977 R-CARBON;8.2Kohm,5%,1/8W,AA,TP,1.8x3.2m
3 R236 2001-000548 R-CARBON;270KOHM,5%,1/8W,AA,TP 3 R102 2001-001000 R-CARBON ;82Kohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R157 2001-000568 R-CARBON;27OHM,5%,1/8W,AA,TP,1 3 R411 2004-001373 R-METAL,FILM;RM1/2T100K-F
3 R914 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1 3 R412 2004-001373 R-METAL,FILM;RM1/2T100K-F
3 R610 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1 3 RX04 2004-001376 R-METAL(S);11KOHM,1%,1/2W,AA,T
3 R240 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1 3 R408 2004-001390 R-METAL(S);1KOHM,2%,1/2W,AA,TP
3 R253 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP 3 R854 2004-001983 R-METAL;2.49KOHM,1%,1/2W,AA,TP,2.4X6.4
3 R252 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP 3 RX03 2004-001987 R-METAL;4.3KOHM,1%,1/2W,AA,TP,
3 R251 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP 3 R303 2001-000908 R-CARBON ;62Kohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R218 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP 3 R308 2001-000908 R-CARBON ;62Kohm,5%,1/8W,AA,TP,1.8x3.2mm
3 R512 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP, 3 R821 2004-004089 R-METAL;123KOHM,1%,1/2W,AA,TP,2.5X6.5
3 R511 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP, 3 R809 2008-000205 R-FUSIBLE(S);10OHM,5%,1/2W,AF,
3 R510 2001-000628 R-CARBON;300OHM,5%,1/8W,AA,TP, 3 R410 2008-000206 R-FUSIBLE(S);1OHM,5%,1/2W,AF,T
3 R231 2001-000660 R-CARBON;33KOHM,5%,1/8W,AA,TP, 3 R812 2008-000252 R-FUSIBLE(S);0.47OHM,10%,1/2W,
3 R517 2001-000666 R-CARBON;33OHM,5%,1/8W,AA,TP,1 3 R257 2008-000252 R-FUSIBLE(S);0.47OHM,10%,1/2W,
3 R514 2001-000666 R-CARBON;33OHM,5%,1/8W,AA,TP,1 3 R409 2008-000253 R-FUSIBLE(S);0.47OHM,5%,1W,AF,
3 R513 2001-000666 R-CARBON;33OHM,5%,1/8W,AA,TP,1 3 R518 2008-000266 R-FUSIBLE(S);1OHM,5%,2W,AF,TP,
3 R219 2001-000674 R-CARBON;360OHM,5%,1/8W,AA,TP, 3 R819 2008-001011 R-FUSIBLE(S);0.18OHM,10%,2W,AF
3 R940 2001-000708 R-CARBON;39OHM,5%,1/8W,AA,TP,1.8X3.4MM 3 C802 2201-000119 C-CERAMIC,DISC;100NF,+80-20%,50V,5MM,TAP
3 R951 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 3 C907 2201-000119 C-CERAMIC,DISC;100NF,+80-20%,50V,5MM,TAP
3 R915 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 3 C908 2201-000193 C-CERAMIC,DISC;10PF,0.25PF,50V
3 R703 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 3 C213 2201-000193 C-CERAMIC,DISC;10PF,0.25PF,50V
3 R203 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 3 C201 2201-000292 C-CERAMIC,DISC;1NF,10%,50V,Y5P
3 R202 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 3 C216 2201-000354 C-CERAMIC,DISC;20PF,5%,50V,NPO
3 R153 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP 3 C823 2201-000370 C-CERAMIC,DISC;220PF,10%,50V,Y5P,TP
3 R306 2001-000766 R-CARBON;43KOHM,5%,1/8W,AA,TP, 3 C444 2201-000441 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
3 R222 2001-000773 R-CARBON;470KOHM,5%,1/8W,AA,TP 3 C445 2201-000441 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
3 RU02 2001-000780 R-CARBON;470ohm,5%,1/8W,AA,TP,1.8x3.2mm 3 CX04 2201-000556 C-CERAMIC,DISC;470PF,10%,500V,

7-2
 Electric Parts List

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

3 C411 2201-000556 C-CERAMIC,DISC;470PF,10%,500V, 3 C102 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2

3 C408 2201-000556 C-CERAMIC,DISC;470PF,10%,500V, 3 C110 2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5
3 C406 2201-000556 C-CERAMIC,DISC;470PF,10%,500V, 3 C412 2401-000927 C-AL;22UF,20%,250V,GP,13X20MM,
3 C302 2201-000556 C-CERAMIC,DISC;470PF,10%,500V, 3 C914A 2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5
3 C909 2201-000573 C-CERAMIC,DISC;47PF,5%,50V,NPO 3 C601 2401-000962 C-AL;22uF,20%,50V,GP,TP,5x11,5
3 C807 2201-000599 C-CERAMIC,DISC;560PF,10%,500V, 3 C905 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
3 C212 2201-000982 C-CERAMIC,DISC;10NF,+80-20%,50 3 C311 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
3 C805 2201-000991 C-CERAMIC,HIC;CK45(T)B2KV561-K 3 C207 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
3 C403 2201-000991 C-CERAMIC,HIC;CK45(T)B2KV561-K 3 C205 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
3 C236 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C202 2401-001333 C-ELECTROLYTIC;CE04WTAPG50V0.4
3 C303 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C654 2401-002463 C-ELECTROLYTIC;CE04WTAPG16V470M-M(SG)-VE
3 C915 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C407 2401-001429 C-ELECTROLYTIC;CE04WTAPG50V470
3 CX01 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C821 2401-001486 C-AL;47UF,20%,160V,HR,13X20MM,5MM,T
3 C229 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C901 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
3 C101 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C813 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
3 C104 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C232 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
3 C151 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C231 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
3 C153 2202-000127 C-CERAMIC,MLC-AXIAL;10NF,+80-2 3 C203 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
3 C237 2202-000791 C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP 3 CU03 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
3 C705 2202-000183 C-CERAMIC;CKOAX7R16VT222-MEP05 3 C851 2401-001585 C-AL;47uF,20%,50V,WT,8*11.5mm,5mm,T
3 C703 2202-000183 C-CERAMIC;CKOAX7R16VT222-MEP05 3 C817 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1
3 C612 2202-000279 C-CERAMIC,MLC-AXIAL;47PF,5%,50 3 C812 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1
3 C611 2202-000279 C-CERAMIC,MLC-AXIAL;47PF,5%,50 3 C215 2401-001840 C-AL;100UF,20%,16V,GP,TP,6.3X1
3 C235 2202-000279 C-CERAMIC,MLC-AXIAL;47PF,5%,50 3 C809 2401-001998 C-AL;1000UF,20%,25V,GP,TP,10X20
3 C904 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50 3 C820 2401-001998 C-AL;1000UF,20%,25V,GP,TP,10X20
3 C902 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50 3 C409 2401-001998 C-AL;1000UF,20%,25V,GP,TP,10X20
3 C501 2202-000863 C-CERAMIC;CKOAX7R50VT561-KUP050561 3 C306 2401-002458 C-AL;1000UF,20%,35V,GP,16X25MM
3 C503 2202-000825 C-CERAMIC,MLC-AXIAL;680PF,10%,50V,Y5P,TP 3 C221 2401-002462 C-ELECTROLYTIC;CE04WTAPG16V33M
3 C502 2202-000862 C-CERAMIC;CCOASL50VT391-JUP050 3 L206 2701-000111 INDUCTOR-AXIAL;100UH,10%,2.5X3
3 C218 2301-000395 C-FILM,PEF;18nF,5%,50V,TP,6.5x12.5x3.5mm 3 L208 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3.
3 C204 2301-000188 C-FILM,PEF;1NF,5%,100V,10.5X12 3 L902 2701-000114 INDUCTOR-AXIAL;10UH,10%,2.5X3.
3 C822 2301-000192 C-FILM,PEF;1NF,5%,50V,5.3X10MM 3 L999 2701-000115 INDUCTOR-AXIAL;10UH,10%,2.8X7M
3 C808 2301-000016 C-FILMPEF;22NF,5%,100V,TP,7.2X 3 L301 2701-000116 INDUCTOR-AXIAL;10UH,10%,4.2X9.
3 C301 2301-000016 C-FILMPEF;22NF,5%,100V,TP,7.2X 3 L602 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3.
3 C401 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9 3 L203 2701-000158 INDUCTOR-AXIAL;22UH,10%,2.5X3.
3 C410 2301-000224 C-FILM,PEF;22NF,5%,50V,7.4X3.9 3 L503 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM
3 C234 2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm 3 L502 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM
3 C603 2301-000289 C-FILM,PEF;5.6NF,5%,50V,6.5X5. 3 L501 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2.5X3.4MM
3 C912 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5 3 L901 2701-000197 INDUCTOR-AXIAL;5.6UH,10%,2.5X3
3 C852 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5 3 L204 2701-000207 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
3 C308 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5 3 L202 2701-000207 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
3 C305 2301-000310 C-FILM,PEF;68NF,5%,50V,8.0X8.5 3 L102 2701-000207 INDUCTOR-AXIAL;56UH,5%,2.5X3.4
3 C803 2301-001397 C-FILM,PPF;2.2nF,5%,1.2kV,TP,15x8.5x13.5 3 L152 2701-000202 INDUCTOR-AXIAL;560NH,10%,2.5X3
3 C313 2305-000470 C-FILM,MPEF;68NF,5%,100V,-,5MM 3 L402 2701-001032 INDUCTOR-AXIAL;100UH,10%,5X14MM
3 C230 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 L810 2701-001032 INDUCTOR-AXIAL;100UH,10%,5X14MM
3 C605 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 X201 2801-000226 CRYSTAL-UNIT;3.579545MHZ,20PPM
3 C701 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 L803 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-
3 CU02 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 L811 2901-000299 FILTER-EMIBEAD;BL02RN2-R65T2DB
3 C209 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 Z601 2903-000135 FILTER-CERAMIC;BP,4.5MHZ
3 C210 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 Z201 2903-001022 FILTER-CERAMIC;TR,4.5MHZ
3 C211 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 L802 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6.
3 C222 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 L804 3301-000287 CORE-FERRITEBEAD;AA,3.5X1.0X6.
3 C227 2305-000665 C-FILM;104J, 60V,5MM TAPING 3 SW905 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
3 C405 2305-000704 C-M,POLYESTER;CFS922MTAPG250V1 3 SW904 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
3 C206 2305-001011 C-FILM,MPEF;22NF,5%,100V,3.5X12.5X7.5MM, 3 SW903 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
3 C404 2306-000193 C-FILM,MPPF;360NF,5%,200V,-,7. 3 SW902 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
3 C609 2401-000133 C-AL;1000UF,20%,16V,GP,13X20MM 3 SW901 3404-000244 SWITCH-TACT;15V,20MA,90-170GF,
3 C806 2401-000262 C-AL;100UF,20%,160V,GP,16X25MM,5MM, 3 F801B 3602-000114 FUSE-HOLDER;-,-,30MOHM
3 C309 2401-000360 C-AL;100UF,20%,50V,GP,8X11MM,5 3 F801A 3602-000114 FUSE-HOLDER;-,-,30MOHM
3 C702 2401-000471 C-AL;10UF,20%,50V,BP,6X11MM,5M 3 J155 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C816 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J159 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C903 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J199 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C911 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J203 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 CX02 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J152 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 CX03 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J151 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C108 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J150 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C220 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J149 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C225 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J503 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C233 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J502 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C310 2401-000480 C-AL;10UF,20%,50V,GP,5X11MM,5M 3 J501 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C312 2401-000553 C-AL;1UF,10%,50V,GP,5X11MM,5MM 3 J450 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C304 2401-000553 C-AL;1UF,10%,50V,GP,5X11MM,5MM 3 J445 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C226 2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM 3 J206 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C219 2401-000603 C-AL;1UF,20%,50V,GP,5X11MM,5MM 3 J204 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C651 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2 3 J123 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C604 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2 3 J120 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 C214 2401-000660 C-ELECTROLYTIC;CE04WTAPG50V2.2 3 J118 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A

7-3
Electric Parts List

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

3 J117 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J087 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A

3 J115 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J109 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J114 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J108 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J113 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J107 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J112 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J106 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J145 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J105 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J144 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J103 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J142 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J102 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J140 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J101 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J137 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J074 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J134 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J073 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J130 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J071 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J124 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J070 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU94 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J069 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU91 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J067 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JF01 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J064 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J504 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J061 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU10 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J082 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU04 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J081 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU03 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J080 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU02 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J079 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 RX07 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J075 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 R413 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J076 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JX01 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J077 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JWK04 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J078 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JWK01 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 JAW01 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 JU95 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 JAW02 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J803 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 JAW03 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J802 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 J808 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J612 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 JWU02 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A
3 J604 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 02VER AA41-11037C PCB-MAIN;K15A,1L,FR-1,245x245x1.6T,-,-
3 J603 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY814 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J153 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY811 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J999 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY809 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J902 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY804 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J901 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY815 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J807 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY830 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J806 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY824 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J805 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY822 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J111 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY821 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J050 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY816 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J049 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY802 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J047 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY413 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J045 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY412 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J043 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY411 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J041 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY410 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J036 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY409 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J059 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY408 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J058 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY406 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J056 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY405 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J055 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY401 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J054 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY414 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J053 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY801 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J052 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY602 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J051 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY601 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J023 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY415 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J022 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY418 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J017 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY419 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J016 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY501 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J015 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY402 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J014 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY403 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J011 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EY803 AA60-40011A EYELET;-,ID2.0,OD2.8,-,-,BST
3 J010 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EL801 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP
3 J034 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EL802 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP
3 J033 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EL301 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP
3 J030 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EL302 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP
3 J029 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 EL404 AA60-40011B EYELET;-,ID2.2,OD3.2,-,-,BSP
3 J027 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT801 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J026 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT802 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J025 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT803 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J024 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT804 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J100 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT805 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J099 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT301 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J093 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT302 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J091 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT401 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J089 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT402 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO
3 J088 3812-000219 WIRE-SO,COPPER;TA0.6SN/52M/M(A 3 GT501 AA60-40014A PIN-GT,ASSY;1P,-,-,AUTO

7-4
 Electric Parts List

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

3 R811 2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AB,

3 R813 2008-001058 R-FUSIBLE(S);0.18OHM,10%,1W,AF
3 C810 2305-000412 C-FILM,MPEF;470NF,5%,63V,-,5MM
ASSY-LABEL
3 Q801 1203-001217 IC-POST,ADJUSTREG;431,T0-92,3P,4.58MIL,P
3 R307 2001-000864 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm 1 A/LABL AA90-01002A ASSY-LABEL;K-MART,K15A,19,USA
3 L/LINE AA68-01544A LABEL;LINE,ALL MDL COMMON
3 C505 2201-000723 C-CERAMIC,DISC;4.7nF,20%,3KV,Y5U,TP,16x5 2 BOX AA68-01542A LABEL;(UNIBOX),PAPER WHT ALLMD
3 R816 2001-001134 R-CARBON(S);360OHM,5%,1/2W,AA,TP,2.4X6.4 2 L/RAT AA68-00373A LABEL-RATING;ART-PAPER,CM19001,K-MART,W
3 R817 2001-001134 R-CARBON(S);360OHM,5%,1/2W,AA,TP,2.4X6.4 2 L/QMS AA68-01554A LABEL;QMS,UARCOWHITEPAPER#1343
3 R818 2001-001134 R-CARBON(S);360OHM,5%,1/2W,AA,TP,2.4X6.4 2 L/WARN AA68-01618A LABEL-WARNING;WHTPAPER100
3 R406 2003-001024 R-METALOXIDE(S);150OHM,5%,2W,A 2 L/IND AA68-00524A LABEL-INDICATOR;A/P 90(G),CXJ1352X/XAA,U
3 R406A 2003-001024 R-METALOXIDE(S);150OHM,5%,2W,A 2 L/SET AA68-01568A LABEL;SET,A48KRD82X,SAMS.23-28KV
3 R104 2003-000592 R-METALOXIDE(S);22OHM,5%,2W,AD
3 R105 2003-000592 R-METALOXIDE(S);22OHM,5%,2W,AD
3 R106 2003-000664 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M ASSY-CRT
3 R107 2003-000664 R-METAL OXIDE(S);330HM,5%,2W,AF,TP,4X12M
3 R101 2001-000812 R-CARBON;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2mm
1 A/CRTP AA94-50014M ASSY-CRT;A48KRD82X(H),+38OMG ,20
3 R814 2001-001135 R-CARBON(S);36KOHM,5%,1/2W,AA,
3 R815 2004-001408 R-METAL(S);91KOHM,1%,1/2W,AA,T
2 CRT AA03-10029W CRT-COLOR;A48KRD82X(H),+380MG,SEMI-TINT.
3 C815 2401-000223 C-AL;100NF,20%,50V,LL,5X11MM,5MM,TP
2 D-Y AA27-50004W DEFL-YOKE;-,DSE-1992LL(1H),20’/A48KRD82X
3 R803 2003-002008 R-METAL OXIDE(S);18KOHM,5%,2W,AF,TP,3.9X
2 C-Y AA27-00002A MAGNET-CONVERGENCE;JH291-SC-OB,29.1M
3 R804 0403-001330 DIODE-ZENER;MTZJ30A,26.99-28.39V,500mW,D
2 SPACER AA63-60028A SPACER-DY;-,NEOPRENE,-,BLK,V0W
3 Q902 0501-000389 TRANSISTOR;KSC815-Y(TAPG)/YTAM
2 TAPE 0203-000432 TAPE-ACETATE;ACETATET0.25W19WH
3 J096 2001-000019 R-CARBON(S);10ohm,5%,1/2W,AA,TP,2.4x6.4m
3 C910 2201-000558 C-CERAMIC,DISC;470PF,10%,50V,Y
3 RU03 2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,
3 C906 2201-000863 C-CERAMIC,DISC;680PF,10%,50V,Y ASSY-TBC,WIRE
2 F801 3601-000144 FUSE-FERRULE;125V,4A,SLOWBLOW,
2 C402 2306-000255 C-FILM;CF922P1.6KVT742-HBUP 1 A/TBC AA98-70014B ASSY-TBC,WIRE;20,NTSC,1P
2 SF101 2904-001241 FILTER-SAWAV;M1871M45.75MHz,SIP5K,14.4dB
2 SW906 3404-000295 SW-TACT,V;KPT1122R1KEYSTT=0.3M
2 P801 1404-001156 THERMISTOR-PTC;9OHM,+30%/-20%,220VRMS,27
2 NT801 1404-001045 THERMISTOR NTC;4.7OHM,15%,2900K,35.0MW,T
ASSY-ACCESSORY
2 C814 2306-000212 C-FILM,MPPF;470NF,20%,250V,-,22.5MM,BK
2 H-COVE AA64-01355B INLAY-COVER;K15A,PVC SHEET V0,T0.4,-,BLK 1 A/ACCS AA97-20009P ASSY-ACCESSORY;CM19001X/KMT
2 R599 2008-001093 R-FUSIBLE(S);22OHM,5%,1/2W,AC,BK,2.5X6.5
2 JU96 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,- 2 PE-BAG AA69-01195A BAG PE;CL29A6W8X,HDPET0.012,93/4X151
2 I/B AA68-00282A MANUAL-USERS;K15B,ENG,-,FOLDING,W/P 100G

ASSY-CABINET,(COM)
REMOCON
1 A/BACK AA92-10046G ASSY-CABINET,(COM);CM19001X/KMT
1 RMT AA59-00066A REMOCON;-,TM52,SZM354EP,25,L/GRAY,E/X,
2 CB+CF 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
2 STAPLE AA60-40006A PIN-STAPLE;-,-,-,H18,33X17.8X2
2 C/RIG AA69-00155A CUSHION-RIGHT;EPS,FOAMED,C=0.02,20F2
2 C/LEFT AA69-00155B CUSHION-LEFT;EPS,FOAMED,C=0.02,20F2
2 PE-BAG AA69-01208A BAG;SHEET,19-20,W42,L50,FOAM,OEM
2 AC-TAP 0203-001279 TAPE-OPP MASKING;#232,T0.14,W15,L50000,Y
2 TAPE-D 0203-001279 TAPE-OPP MASKING;#232,T0.14,W15,L50000,Y
2 BXTAPE 0203-001295 TAPE-OPP MASKING;1242,T0.06,W100,L91.4M,
2 B/C AA64-00154B CABINET-BACK;-,20F2 R1,-,HIPS,V0,BLK,-,-
2 PCK AA69-01172A PACKING CASE;CM19001,CBSW,KRFT-LNR,275,K
2 L/RAT AA68-00373A LABEL-RATING;ART-PAPER,CM19001,K-MART,W
2 AC+BC AA65-30008A CLAMP-CORD;-,PE,HB,BLK,-,-
2 CLW/HS AA65-30018A CLAMP-WIRE;-,NYLON6.6,-,-,DATL

ASSY-CABINET,FRONT
1 A/FRNT AA92-30161J ASSY-CABINET,FRONT;CM19001X,20F2R1-HIPS

2 SPK+CF 6002-000512 SCREW-TAPPING;RH,+,2,M4,L12,ZP

2 STOPER AA61-40113A STOPPER-PCB;-,ABS,HB,NTR.
2 A/SPK AA96-10141A ASSY-SPEAKER;3W,8OHMX1,700
3 SPK 3001-001020 SPEAKER;3W,8ohm,90dB,140Hz
3 L/SPK AA39-20501C LEAD CONNECTOR-ASSY;-,67096-003,REC,3(2)
2 D-COIL AA27-20004B COIL-DEGAUSSING;-,20,5.7ohm,30T,L2170,E
2 F/C AA64-00150B CABINET-FRONT;-,20R1,BK708P EGH,HIPS,VO,
2 CRT+CF AA60-10050R SCREW-ASSY;WC,HH,+M5,L31.5,SWR
2 CDCOIL AA61-00734A HOLDER;25POLYVINYL,DEGAUSSING,CHLORI
2 CWIRFC AA65-30105A CLAMP-WIRE;NYLON 66N,VO,NTR,15MM
2 S/CRT AA60-00038A SPACER-CRT;PS,SHEET,T1.0,BLK,OD22,ID10.

7-5
 MEMO

7-6 Samsung Electronics

 Block Diagram

8. Block Diagram

IC601

TU01* SOUND-AMP
2.5W x 1CH
TUNER SAW LA4425
TELH9-212A M1859M

DUAL
IC902 IC201

EEPROM 1CHIP
KS24C020 IF/V/C/D
KA2163B R.G.B
CRT

I2C BUS
Q401*
IC901*
H-TR
KSC5368
MICOM
SZM-354ET
EXT IN EXT IN
VIDEO AUDIO T444*
VERTICAL-AMP
KA2131
F.B.T
D807 ~ D810
T801* 14" : FSV14A001
20" : FSV20A001
SWITCHING (125V) 21" : FSV20A001
TRANS

S:125V,12.5V (12.5V)
IC802
(5V)
IC801* MICOM
PC802 MULTI-REGULATOR
SPS CONTROL KA7631
KA3SO680 PHOTO 1CHIP
KA3S0765 COULPER (9V)

Samsung Electronics 8-1

 PCB Layout

9. PCB Layout

9-1 PCB-MAIN
Loc. No. X Y Loc. No. X Y
DIODE IC
D101 53 150 IC201 100 164
D102 56 130 IC301 50 132
D103 71 141 IC601 146 225
D201 135 196 IC602 168 221
D202 96 105 IC801 155 10
D203 96 107 IC802 141 97
D204 96 110 IC901 215 153
D205 123 92 IC902 219 178
D206 114 95 ICK01 69 213
D207 114 97 TRANSISTOR
D208 115 74 Q151 61 183
D210 99 105 Q201 107 129
D299 99 212 Q202 101 140
D301 32 139 Q203 99 144
D302 31 146 Q401 24 85
D401 85 99 Q402 63 118
D402 70 98 Q501 24 197
D403 59 74 Q502 32 197
D404 72 53 Q503 12 195
D405 81 38 Q601 145 203
D407 58 105 Q602 132 223
D601 124 213 Q801 100 29
D701 130 136 Q902 119 226
D702 227 203 Q903 87 115
D703 210 238 QL01 80 237
D704 85 159 QL03 115 226
D802 104 11 QLK1 106 229
D803 150 23 QU01 197 173
D804 92 183 QU10 195 115
D805 168 42 QX01 112 113
D806 150 27
D807 186 51
D808 193 54
D809 186 67
D810 196 66
D814 99 60
D855 157 100
D856 147 101
D901 160 119
D902 163 110
D903 171 130
D904 132 96
D905 231 179
D906 157 131
DL01 105 219
DL02 108 219
DU01 211 118
DX01 116 107
DX02 111 101
DZ801 215 20
DZ802 179 30
DZ803 178 24
DZ806 157 17
DZ807 150 20
DZ901 231 83
DZ902 231 156
DZ903 203 124

Samsung Electronics 9-1

 Wiring Diagram

10. Wiring Diagram

CRT PCB
CRT PCB
SPEAKER
S B B
G G G
CN601
S R R
G 9V 9V
GND GND
180V 180V
GND GND
HT HT
CN201 CN501
CN501

MAIN ASSY

A/V ASSY
CRT CN401 V1 V1
H1 H1 R+ R+
H2 H2 R- R-
V1 V1 V0 V0
V2 V2 GND GND
AI AI
A0 A0
CN701 CN702

Samsung Electronics 10-1

 Schematic Diagrams

11. Schematic Diagrams

11-1 MAIN 1/4

: Power Line
: Signal Line

Samsung Electronics 11-1

Schematic Diagrams

11-2 MAIN 2/4

TP13 TP14
IC201 30PIN IC201 32PIN

TP15 TP16
IC201 37PIN IC201 41PIN

TP18

TP16 TP17 TP18

TP21 TP14 IC201 43PIN IC201 45PIN
TP20

TP13
TP19 TP15
TP17 TP19 TP20
IC201 47PIN IC201 49PIN

TP2 TP12
TP5 TP12 TP21
TP6 IC201 28PIN IC201 53PIN

TP4 TP10
TP11
TP1

TP7
TP9
TP3 TP8
TP10 TP11
IC201 25PIN IC201 27PIN

TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9

IC201 2 PIN IC201 4 PIN IC201 7PIN IC201 19PIN IC201 20PIN IC201 21PIN IC201 22PIN IC201 23PIN IC201 24PIN

: Power Line
: Signal Line

11-2 Samsung Electronics

 Schematic Diagrams

11-3 MAIN 3/4

TP24

TP24
TP25
IC801 1 PIN

TP26

TP25

TP27
TP27
T444 10 PIN

TP26

: Power Line
Si l Li

Samsung Electronics 11-3

Schematic Diagrams

11-4 MAIN 4/4

: Power Line
: Signal Line

11-4 Samsung Electronics