JT701D User Manual

V1.3

Shenzhen Joint Technology Co.,Ltd

March 10, 2025

1 / 38
 Contents
Contents ...................................................................................................................................................................................................................2
Copyright and Disclaimer .................................................................................................................................................................................. 4
Warranty Policy Statement ................................................................................................................................................................................ 4
Brief Introduction .................................................................................................................................................................................................. 4
Product Functions .................................................................................................................................................................................................5
Product Specification ...........................................................................................................................................................................................8
Standard and optional accessories .............................................................................................................................................................. 10
Appearance .......................................................................................................................................................................................................... 11
Front view .................................................................................................................................................................................................... 11
Rear view ...................................................................................................................................................................................................... 12
Interior view of Back cover .................................................................................................................................................................... 12
Bottom View Instructions ....................................................................................................................................................................... 13
First Use ..................................................................................................................................................................................................................13
Power On and Off / Charge and Full ................................................................................................................................................. 13
Install the Micro-SIM Card .................................................................................................................................................................... 14
Instruction of double sim card working logic ........................................................................................................................15
Definition of LED and Buzzer ................................................................................................................................................................15
LED Status...........................................................................................................................................................................................15
Buzzer and Blue LED .......................................................................................................................................................................16
Wake Up Source ........................................................................................................................................................................................17
Preparation before configuration ........................................................................................................................................................18
Micro-USB configure cable and connect to computer via USB port ............................................................................18
Open JT701D Assistant tool .........................................................................................................................................................18
Check the communication connection .................................................................................................................................... 19
Basic Configuration .................................................................................................................................................................................. 19
Query firmware version, device ID and battery power ...................................................................................................... 19
Terminal timing ................................................................................................................................................................................ 19
Power switch control ...................................................................................................................................................................... 19
Restore factory setting ...................................................................................................................................................................20
Main IP/ Domain name, port, APN, APN account configuration ................................................................................... 20
Sleep mode-wake up upload interval and sleep configuration ..................................................................................... 20
Tracking mode ..................................................................................................................................................................................21
Vibration Detection Value ............................................................................................................................................................ 21
Working Mode Description ................................................................................................................................................................... 21
Standby mode ...................................................................................................................................................................................21
Deep sleep mode-low battery ....................................................................................................................................................22
Tracking mode ..................................................................................................................................................................................22
Reference Working Hours ......................................................................................................................................................................22
Unlock and lock ......................................................................................................................................................................................... 23
Remote static password unlock ..................................................................................................................................................23
RFID Authorization card unlock ..................................................................................................................................................23
Lock .......................................................................................................................................................................................................24
SMS function related configuration ................................................................................................................................................... 24
Authorize mobile phone VIP number and enable VIP number to receive SMS alarm .......................................... 24
2 / 38
 Turn on the phone or SMS to wake up the device ............................................................................................................. 25
Configure time difference-SMS alarm ..................................................................................................................................... 25
RFID Authorization card configuration ............................................................................................................................................. 25
Query and add authorization card ............................................................................................................................................25
Delete authorization card ............................................................................................................................................................. 26
Delete all authorization cards ......................................................................................................................................................26
Geo fence function configuration ....................................................................................................................................................... 26
Alarm configuration ................................................................................................................................................................................. 27
Alarm type and conditions ........................................................................................................................................................... 27
Configure Alarm channel switch ................................................................................................................................................ 28
Edit command configuration interface ..............................................................................................................................................28
Product peripherals -JT126 temperature and humidity sensor ...............................................................................................29
JT126 Introduction ...........................................................................................................................................................................29
JT126 Technical parameters .........................................................................................................................................................29
JT126 Power on and power off ...................................................................................................................................................30
Bind JT126 temperature and humidity sensor with JT701D .............................................................................................30
Unbind JT126 temperature and humidity sensor from JT701D ......................................................................................30
Product Peripherals -JT709 Bluetooth slave lock ..........................................................................................................................31
JT709 Introduction ...........................................................................................................................................................................31
JT709 Technical parameters .........................................................................................................................................................31
Bind JT709 with JT701D .................................................................................................................................................................32
Unbind JT709 from JT701D ..........................................................................................................................................................32
To use the device in Jointech Cloud platform ......................................................................................................................................... 34
Login .............................................................................................................................................................................................................. 34
Manage your asset in the platform .................................................................................................................................................... 34
Device and its Peripherals’ installation ....................................................................................................................................................... 34
JT701D’s installation .................................................................................................................................................................................34
JT126 Temperature & Humidity sensor’s installation. ................................................................................................................. 35
JT709 Bluetooth Slave Lock’s installation ......................................................................................................................................... 36
Device Maintenance .......................................................................................................................................................................................... 37
Trouble Shooting ................................................................................................................................................................................................37
Contact us ............................................................................................................................................................................................................. 38

3 / 38
Copyright and Disclaimer
Copyright ©Shenzhen Joint Technology Co.,Ltd. User can read and photocopy this document, but without the

permission of Jointech, please do not modify this document or quote design pictures of products in this document.

All the contents in this document are currently accurate. However, due to the continuous iteration and update

of products, we may update the manual from time to time. The manual you are reading reflects the basic functions

and technical indicators of the product at the time the product manual was written. We strive to give a complete

and clear description as much as possible so that you can easily use our products. There may be inaccurate

technical expressions of some content. We will correct and update the manual content in time based on customer

suggestions and feedback. This manual is subject to update without notice.

The user needs to install and fix the product, charge the battery according to the specifications, and dispose of

the waste parts and batteries of the product in accordance with local policies and regulations. Jointech is not

responsible for any loss, injury, environmental pollution, etc. caused by using or quoting this product.

Warranty Policy Statement

The warranty period is 12 months from the date of delivery.

Any defects, malfunctions and damages caused by improper use, unauthorized disassembly and alteration of

the product are not applicable to this warranty policy.

The warranty period is limited to repairing defects or replacing defective parts.

Repairing or replacing parts under the terms of this warranty period does not extend the warranty period.

Brief Introduction
JT701D is a mobile asset monitoring and management product based on JT701 electronic smart lock. The

product currently supports 2G/4G communication mode with a built-in battery of 15000mAH. JT701D have been

optimized and improved in low power consumption, peripheral expansion, and functional design. The working

modes are diversified. According to the demand of power consumption, deep sleep mode and tracking mode are

added to the existing dormant mode. The default 50 RFID authorization cards will be expanded to 500 RFID

4 / 38
authorization cards. In terms of security, a control unlocking channel has been added. For example, user can

specify whether they can unlock via SMS, RFID authorization card, serial port, Bluetooth, cellular network and

other channels. In terms of peripheral expansion, JT701D can support 10 JT126 wireless temperature and

humidity sensors to work at the same time, or 10 JT709 Bluetooth sub-locks to work at the same time. It has a

key-free design, RFID/remote unlocking; large-capacity battery, long working hours; built-in wireless module,

real-time online monitoring; built-in GPS module, global positioning tracking; security monitoring, illegal unlocking

alarm and other functions. It is suitable for remote monitoring of containers, flatbed trucks, box-type trucks, etc.

Product Functions
Hardware/Firmware
Main Functions Function Description
Functions
Hardware Functions Based on 2G/4G network communication
GPS + LBS positioning
Dual SIM card Support two Micro-SIM cards, dual
card single standby mode work. The
device will automatically select the
SIM card for network registration.
Lock rope status detection Check the insertion and unplug
status of the lock rope.
Lock rope length can be customized Default 35 cm.
Buzzer and indicator light In different operating scenarios,
different buzzers and indicators
provide sound and light prompts;
LED lights support satellite
positioning, communication status,
power status, and charging status
indication.
DC 5 /12V 2A charging DC 5V /2 A about 8 hours can be full
battery.
Serial port/Micro-USB configuration, Serial port, can be used for firmware
upgrade, debugging upgrade,parameter configuration and
debugging. Micro-USB interface, can
be used for charging and parameter
configuration, reading swiping card
event and location data (customized
function).
Internal battery 15000mAH Rechargeable lithium battery.

5 / 38
 Acceleration sensor Motion and vibration detection.
Lora wireless gateway (optional) Used for peripheral JT126 wireless
temperature and humidity sensor
and JT709 Bluetooth sub-lock
communication.
Bluetooth unlock (optional) The mobile APP connects to the
device via Bluetooth, unlocked by the
Bluetooth channel.
display screen (optional) The display screen shows the QR
code, and the mobile phone scans
the QR code to unlock.
Firmware Functions Real time location query The current device location can be
queried through SMS commands.
Location tracking GPS+LBS
Remote password unlock Static password unlock, static
password remains unchanged, the
user needs to remember this
password.
Dynamic password unlock The dynamic password is actively
reported by the terminal. The
platform needs to record the dynamic
password and send the dynamic
password through the platform to
unlock. After each locking the device,
the password is updated and
reported to the platform to notify the
platform to update the password.
Dynamic password associated fence In the custom fence, the platform
unlock sends a dynamic password to
unlock.
RFID authorization card unlock Use authorized RFID card, swipe
card to unlock
RFID authorization card associated fence The authorized RFID card can only
unlock be unlocked inside the fence.
Support the configuration of 500 Used to configure 500 RFID cards
authorized RFID cards for unlocking with authorized unlocking
10 polygonal Geo-fences A fence can support up to 50 location
nodes
Automatically lock Insert the lock rope and lock
automatically.
Lock and unlock report and statistics Platform statistics are required, with
the lock record as the starting point;
the unlock record after the lock is
closed as the end point. One record

6 / 38
 is one trip.
Support 5 authorized VIP numbers VIP mobile phone number can
support SMS command sending,
SMS alarm receiving, etc.
Support 10 alarms The alarm can be sent to the VIP
Steel string cut, mobile phone number via short
Swipe unauthorized RFID card message or sent to the platform via
Unlocking cellular network.
Wrong password for 5 consecutive times (such as GPRS/3G/4G network).
Enter Geo-fence
Exit Geo-fence
Low battery
Motor stuck lock
Open Back cover
Vibration
Mileage statistics In the tracking mode, the mileage is
accumulated continuously; in the
other modes, the mileage is
accumulated with poor accuracy and
is not recommended for reference
Blind area supplementary report : The Swipe card reports and the
Minimum of 23,000 caches for location location data are saved in the same
and Swipe card reports area of flash.
Remote firmware upgrade Support
Deep sleep mode Deep sleep mode: It is only allowed
Tracking mode to swipe the card to unlock, charge,
Standby mode restart the power switch to wake up,
and the Cellular communication
module doesn’t work and send
data. If the current battery level is
less than 5%, it will enter deep sleep
mode, and the user can configure the
remaining power percentage for
entering deep sleep;
Tracking mode: the device works
continuously and does not enter
sleep ;
Standby mode: sleep by default;
When the wake-up condition is
detected, the preset data upload time
interval works, and when there is no
other wake-up event, it sleeps.

Device wake-up source Premise: the device is dormant

7 / 38
 Reboot the device (it’s not configurable) After starting up, wake up for 10
minutes, and sleep when there is no
other wake-up source;
Vibration wake After detecting the vibration, wake up
(can be configured to close) for 10 minutes, during which there is
no other wake-up source, then sleep;
Back cap opened (cannot be configured After detecting that the Back cap is
to close) opened, wake up for 10 minutes,
during which there is no other
wake-up source, then sleep;
Lock rope inserted and unplugging When the lock rope is inserted and
(cannot be configured to close) unplugged, wake up for 10 minutes,
during which there is no other
wake-up source, then sleep;
Connect to external power Detect external charging, wake up
(cannot be configured to close) and work for 10 minutes, during
which there is no other wake-up
source, then sleep;
Swipe RFID card Detect swiping RFID card, wake up
(cannot be configured to close) and work for 10 minutes, during
which there is no other wake-up
source, then sleep;
Short message, wake-up call Detect the short message or dialing
(can be configured to close) sent by the VIP mobile phone
(Default VIP number, non-VIP number number, then wake up and work for
can be configured) 10 minutes, during which there is no
other wake-up source, then sleep;
RTC timed wake-up Wake up at a preset time interval and
(cannot be configured to close) upload a piece of data, then sleep;
Lora gateway (optional) Lora gateway detects the peripheral
(cannot be configured to close) request to send data, wakes up for
10 minutes, during which there is no
other wake-up source, then sleeps;

Product Specification
Parameters Description
Dimension( L x W x H ) 195mm*114mm*37mm
Weight 700g（Including standard accessories）
Shell material Engineering Plastic

8 / 38
Built-in battery Rechargeable 15000mAH lithium battery
Working temperature -20℃ ~ 60℃
Storage temperature -40℃ ~ 80℃
Relative humidity 5%~95%
Waterproof and
IP67
dustproof grade
Average sleep current 2G :
Enable SMS wakeup：3.3 mA
Turn off SMS wakeup：382uA
4G :
Enable SMS wakeup：Average current 3.173mA.
Turn off SMS wakeup：Average current 1.584mA.
Average working current 2G : 42.1mA
4G : 38.1mA
GNSS/Cellular module
Built-in
antenna
GNSS Module Ublox-MAX-7Q
Cold start positioning time：29 seconds
Hot start positioning time：1 second
Warm start positioning time：28 seconds
Cellular module 2G Module GSM/EDGE 850/900/1800/1900Mhz
communication 4GModule TDD-LTE B38/B40/B41
frequency band FDD-LTE B1/B3/B5/B7/B8/B20
WCDMA/HSDPA/HSPA+ B1/B5/B8
GSM/GPRS/EDGE 900/1800 MHz
4GFull band 4G LTE band：
B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19
/B20/B25/B26/B28/B34/B38/B39/B40/B41/B66
UMTS/HSPA+: B1/2/B4/B5/B6/B8/B19
GSM/GPRS/EDGE: 850/900/1800/1900MHz
SIM card Micro-SIM card, dual card

Lora Gateway Frequency：433MHz

(optional) Receiving sensitivity：-148dBm
Maximum transmit power：17dBm
Maximum transmission rate：300kBps
Transmission distance：＞150m (open environment)

Bluetooth gateway Support Bluetooth 5.0

(optional) Bluetooth frequency : 2.4GHz ±30KHz
Bluetooth communication distance : 2-10 meter
Bluetooth antenna signal strength : ＞4 dBm

9 / 38
Standard and optional accessories
Standard Optional
Name Picture
accessories accessories
Lock body
(standard configuration)

Lock body Same as above picture

●
(Lora gateway)
Cable (length of 35 cm)

RFID Cards (two units)

●

Micro-USB
Configuration/charging
●
cable

Serial port configuration

cable
●

Serial port upgrade

cable
●

Charging adapter and

matching charging
●
cable

Powerful magnet
●

10 / 38
 JT126 Temperature and
humidity sensor
●

JT709 Bluetooth
sublock

Appearance

Front view

①RFID card swiping sensing area

②Indicator light
Blue light GPS - GPS positioning status indication
Green light GSM - Cellular network communication status indication
Yellow light LVS - Low battery indication
Red light / Green light CHG - Charge status and battery full status indication
③Cable: the default length is 35 cm, and the length can be customized;
Insert the lock body to lock automatically.

11 / 38
Rear view

No powerful magnet on the back Back cover with powerful magnet

cover (standard) (optional)

Interior view of Back cover

Open the back cover Internal view

①Power switch: Push the power switch to the ON position to the left, that is, start up;
Turn OFF the power switch by pushing it to the right
②Micro-USB Interface：Micro-USB Configuration cable, which can be used to configure device
parameters and charge internal batteries;
③Serial debugging interface : serial configuration cable, which can be used for configuring
device parameters and debugging when device works abnormally.
④SIM1 Card slot : supports Micro SIM card, and the current working mode is dual card single
standby mode.
⑤SIM2 Card slot : supports Micro SIM card, and the current working mode is dual card single
standby mode.

12 / 38
Bottom View Instructions

① External charging port : DC 5V 2a is the standard charging voltage. Please connect the
charging adapter and its matching charging cable provided by Jointech. It is
recommended to use a stable and reliable indoor charging power supply to
charge the device. And it usually takes about 8 hours to charge from 5% low
battery to 100% full battery.
②Device ID : The device ID is a 10-digit number, for example: 8040313607. This device ID is
included in the location data uploaded by the device, and this ID is used as the
unique identification of the device in the platform.
Device model : At present, JT701D is divided into 2G and 4G device models according to
different cellular network communication modules.
③Buzzer Sound Hole.

First Use

Power On and Off / Charge and Full

Power on and off : Unscrew the screws of the back cover with a special hexagonal screwdriver, and then refer
to the power switch in the " Interior view of Back cover" in this article, flip the power switch to
turn on or off.
Charge and full : After power on, if the LVS-yellow light flashes, it means that the current battery level is less
than30%, and charging is recommended.
Charging method 1-Charge the device through the standard charging adapter and supporting
charging cable and wait for the charging indicator CHG to change from red to green; In
general, it takes about 8 hours for the equipment to run out of power to be fully charged.

Charging adapter and supporting line

Charging method 2-Connect the USB port of the computer to charge through the Micro-USB

13 / 38
 configuration line, and wait for the charging indicator to change from red to green; This
interface limits the charging current to 500 mA which can only be used as a backup
method and is not recommended as a daily charging method.

Micro-USB configuration/charging cable

Warning：
Do not directly plug the special double-post plug of the charging cable that comes with the adapter into
the power socket, otherwise it is easy to cause indoor circuit short circuit or electric shock!
Do not use unstable or unreliable power sources such as vehicle batteries to charge the JT701D device!

Install the Micro-SIM Card

Please confirm the cellular communication module used by the current device with Jointech’s sales staff. If
the current device uses a 2G communication module, please communicate with the local mobile operator and
confirm that the SIM card has activated the GPRS Internet access function and connect to the Internet. Place
the Micro-SIM card that has activated the GPRS network access function into the SIM card slot and lock it.

Micro-SIM Card - Length * width (15*12mm)

Pay Attention：
Before inserting the SIM card, please turn off the device to avoid damage to the SIM card;
If use a single SIM card, it is recommended to insert the SIM1 card slot.
As shown below, the process of inserting the SIM card into the SIM1 card slot and fixing it:
① ② ③ ④

①Press the upper end of the metal cover with your fingers (or the place where your thumb nail is
embedded in the red frame) and push the metal cover down.
②Open the metal cover.
③ Place the SIM card in the SIM1 card slot, press the metal cover, and push the metal cover
14 / 38
 upwards until the SIM card is locked.
④SIM card is finished installation.

Instruction of double sim card working logic

For users who use single sim card, just skip this instruction.
Recent JT701D support dual sim card one standy. It means when one sim card is connected with nextwork,
the other sim card won’t work.
Note: Please following the instruction of <Main IP/ Domain name, port, APN, APN account configuration> in
this article for the initial setting.
The device will detect whether the SIM card is inserted into the SIM card slot, and the following figure
indicates whether the current SIM card and its APN and APN account parameters can be connected to the
backend server host IP (domain name) and port.

Note：
The currently configured host IP (domain name) and port do not have a one-to-one correspondence with
the SIM card slot. The same SIM card may work in the configured (IP1, port 1) or (IP2, port 2). Allow
users to set IP1 and IP2 or port to the same parameter.
The configured APN1 and APN2 information corresponds to the SIM card slot one by one. For example,
the APN and APN accounts of SIM1 connected to the GPRS/4G network must correspond to the APN1
and APN1 accounts.

Definition of LED and Buzzer

LED Status

LED Indicators Status Description

Blue LED Flash 3 times every 10sec Capture satellite signal, successfully located

15 / 38
 GPS Location status Flash once every 3sec Not located yet. Instruction: Move it to view
the sky. Lock rope up
Off In sleeping mode or switch off. Wake it up by
shaking or turn on power switch.
Green LED Flash 3 times when sending Connected Cellular network and reporting data
Network communication data and then off
Flash once every 3 sec Not connect to Cellular network yet
OFF In sleeping mode or switch off. Wake it up by
shaking or turn on power switch.
Yellow LED Flash once every 3sec Triggered when remaining battery level is
LVS Low power battery lower than 30%
OFF Enough battery Or device in sleep or switch
off.
Red->Green Keep Red LED on Charging
CHG Charging-> full Keep Green LED on When fully charged, Red turn to Green
charged OFF Not in charging

Buzzer and Blue LED

Condition Description

Switch illegal RFID card

Remote unlock by static
password
Remote unlock(dynamic
password)
Swipe the authorized RFID Buzzer long beep 3 sec. Blue LED keep blink 3 sec
card, but not in the preset
fence
On-site batch registration
authorized more than 20
RFID
Switch authorized RFID
When registering in
batches on site, swipe the
card and register the RFID Buzzer beep once, Blue LED blink once
card successfully
The device is automatically
locked
The external device Buzzer beep once, Blue LED no blink
successfully binds to the
Lora gateway

16 / 38
 Various channels (SMS, 10 seconds after unlocking, if the lock rope is still not pulled out,
RFID card, Bluetooth, the buzzer will sound once every second, and the GPS blue
platform, etc.) issued light
unlock instructions, but did will continue to flash until the lock rope is inserted. Or if the lock
not pull out the lock rope rope is still not inserted for more than 60 seconds, the buzzer
will
stop ringing, the GPS blue light will return to normal, and the
device will be automatically locked.
Lock rope inserted but After unlocking, remove and insert the lock rope within a short
device is not well locked period of time (1 second). If the device does not detect that the
lock rope is inserted, the buzzer will sound once every second
and the GPS blue light will continue to flash until the user pulls
out the lock rope again. Insert the lock rope, the buzzer stops
sounding, the GPS blue light returns to normal, and the device
is automatically locked.

Wake Up Source

Wake-up source (device wake-up Work description (prerequisite, the device is powered on
method) and in sleep state)
Restart the device( by physical After restart, device wakeup and work for 10min then into
switch） sleep if without other wakeup resource
Vibration detecting After detecting vibration, wake up and work for 10 minutes,
during which there is no other wake-up source, then sleep;
Open back cover After the detection back cover is opened, wake up and work
for 10 minutes, during which there is no other wake-up
source, then sleep;
Plug out/insert lock rope When the lock rope is plugged in and unplugged, it wakes up
and works for 10 minutes. During the period, there is no other
wake-up source, then it sleeps;
Connect with power supply Detect external charging, wake up and work for 10 minutes,
during which there is no other wake-up source, then sleep;
Swipe RFID card( no matter Detect swiping RFID card, wake up and work for 10 minutes,
authorized or not) during which there is no other wake-up source, then sleep;
SMS/Call (available for VIP number, if Detect the short message or dialing sent by the VIP mobile
need this function for non-VIP phone number, then wake up and work for 10 minutes, during
number, send related command） which there is no other wake up source, then sleep;
RTC wake up Wake up in time and report one data then into sleep again
Lora gateway (optional) Lora gateway detects that the peripheral requests to send
data, wakes up and works for 10 minutes, during which there
is no other wake-up source, then sleeps;

17 / 38
Preparation before configuration

Micro-USB configure cable and connect to computer via USB port

Connect to JT701D Connect to laptop USB port

Open JT701D Assistant tool

18 / 38
Check the communication connection

On the USBHID configuration interface, if you see JT700, it means that the communication is

normal.

Basic Configuration

Query firmware version, device ID and battery power

Click button, the terminal will return information such as ID number and version number.

Terminal timing

When the user is testing in the indoor environment, since the device is powered on for the first time and does not
obtain the satellite positioning time service, the user can manually time the product through this button. After the
time service, the uploaded location data time will be corrected to the current UTC time. When the device captures
the satellite signal, it will update to the satellite timing time.

Power switch control

Click the Read button to get the initial configuration of the power switch;The default is power switch ON, that is,
power switch can control shutdown and start-up;The user can select 'Off' and click the Write button.You can
modify the current configuration.

19 / 38
Restore factory setting

Under the JT701 configuration software, click "Factory Default(D)" to restore the Factory Settings of the
device.All previous configuration, except IP address, port, APN, VIP number parameter, will be initialized as the
factory default configuration.

Main IP/ Domain name, port, APN, APN account configuration

Click Main IP，configure IP1 and its corresponding parameters. Contact Jointech Sales to obtain the accurate
IP1 address, port, APN, APN account. Click 'Write' button to Write the configuration. Click "Read" to query the
initial configuration of the device.

Click Sub IP, configure IP2 and its corresponding parameters.The user has multiple servers, which can be
configured with host IP2 address, port, APN, APN account and so on.Click 'Write' button to Write the
configuration.Click "Read" to query the initial configuration of the device.
Dual-card and IP1 and IP2 communication principle, please refer to " Instruction of double sim card working
logic" in this article.

Sleep mode-wake up upload interval and sleep configuration

Tracking Uploading Interval: Configure the time interval for uploading data after the device wakes up from
sleep;
Wake up Interval:Configure the RTC wake-up time interval of the device.

20 / 38
 For example, the parameters in the above figure indicate that after the device wakes up, it will upload location
data at an interval of 60 seconds; during the wake-up period (fixed 10 minutes) if the device captures the
wake-up source, such as continuous vibration, it continues to work; if the wake-up source is not captured,
Then it enters sleep, sleeps for 30 minutes, the device RTC wakes up, and after uploading a piece of location
data, it enters sleep again.

Tracking mode

The user can edit the command (P54,1,1) to send in the Advance Operation interface ,the device enters
the continuous tracking mode and no longer enters the sleep state. Until the remaining power of the device is less
than 5%, it enters deep sleep mode

Vibration Detection Value

Set the vibration wake-up parameter, the larger the value, the greater the vibration amplitude required for
vibration wake-up. The range is 63-8000, and the default is 126.

Working Mode Description

Standby mode

After the device is turned on, it is in standby mode and waits for the wake-up condition to be triggered, then the
wake-up device works as expected.
After waking up, the preset data upload time interval is greater than or equal to 60 seconds, then the GPS
module will actively enter the smart sleep state;
21 / 38
 The preset data upload time interval after waking up is less than 60 seconds, the device GPS module will
continue to work during the wake-up period. In this working state, the power consumption will be greatly
increased, affecting the working time of the device.

Deep sleep mode-low battery

By default, if the remaining power of the device is less than 5%, it enters deep sleep mode. In the deep sleep
mode, the communication and positioning module of the device is closed, only RFID card swiping is allowed,
power switch to restart the device, connected to external power three ways to wake up.
Note：
After swiping the card to unlock or the power switch to restart the device, the device detects that there is no other
action currently and continues to sleep. Will not be forced to wake up for 10 minutes. Insert the lock rope and the
device will automatically lock.

Tracking mode

The device is in a continuous working state, and the device remains in the tracking mode even after restarting,
unless the customer actively turns off the tracking mode. When the remaining power is less than 5%, it enters the
default deep sleep mode.

Reference Working Hours

2G/4G JT701D Data Uploading Interval Working hours

/Working Mode
2G JT701D 30 seconds/tracking mode About 10 days
2G JT701D 60 seconds/tracking mode About 17 days
2G JT701D 120 seconds/tracking mode About 17 days

4G-E JT701D 30 seconds/tracking mode About 10 days

4G-E JT701D 60 seconds/tracking mode About 20 days
4G-EJT701D 120 seconds/tracking mode About 20 days

4G-G JT701D 60 seconds/tracking mode About 15 days

The current test is the working time of the equipment under normal temperature, without SMS
wake-up, and indoor testing, for reference only. During the actual test, there will be differences
in varying degrees due to differences in ambient temperature, satellite positioning, and working
modes. Please refer to the actual test.

22 / 38
Unlock and lock

Remote static password unlock

SMS password unlock：

User configure "Authorized mobile phone VIP number", edit the text message content (P43,888888). The
static password of the default device is 888888. You can change it yourself.
As shown below:

Local serial cable unlock:

Open the configuration tool, connect JT701D, enters 888888, and clicks the "Write" button to unlock. After
unlocking, the buzzer will sound for 3 seconds. Pull out either end of the lock rope to unlock.

Platform unlock:
For platform login, refer to the section " Manage your asset in the platform" in this article. For specific
unlock methods, refer to the platform operating instructions.

RFID Authorization card unlock

23 / 38
 When the user gets the JT701D device, the two standard RFID cards have been registered as authorized
unlocking cards. After the device is turned on, place the RFID card in the RFID induction area and swipe the card
(the red box in the picture above), the buzzer will beep, then the motor will rotate, and the user can pull out the
lock rope to unlock;
If the buzzer keeps ringing for 3 seconds, it means that the current RFID card is not registered. Please
refer to this article "Adding an Authorization Card" to add this RFID card to an unlock authorization card.
If there is no sound prompt, check whether it is turned on or whether the battery is exhausted, please
charge the device in time.

Lock

Normally, Once the lock rope insert both ends of the lock rope according to the size of the lock hole. After the
device detects that the lock rope at both ends is inserted, it will be automatically locked.
Normal locking steps:
Insert the lock rope into the lock hole to the end;
Keep the lock rope at the bottom of the lock hole until the buzzer ends;
Pull out the lock rope. If the lock rope cannot be pulled out, it is confirmed that it is locked normally.
Wrong lock operation:
If the lock rope is inserted halfway into the lock hole and has not reached the bottom, or the buzzer has not
sounded yet or the sound has not ended yet, quickly pull out the lock rope;
Wrong locking may cause the motor to be locked, but the lock rope is not locked. Under such case, you need
to unlock the lock before restarting the operation.

SMS function related configuration

Authorize mobile phone VIP number and enable VIP number to

receive SMS alarm

JT701 can set 5 VIP numbers. The mobile phone number cannot exceed 15 digits, and the country code must be
added before it, such as China 86 or +86.

24 / 38
Check the check box behind the VIP number, to select the corresponding VIP number, and set whether it can
receive SMS alarm.

Turn on the phone or SMS to wake up the device

It can be configured to wake up the device by authorized VIP number, telephone or SMS. By default, it is
closed.

Configure time difference-SMS alarm

Correct the time information in the SMS alarm content. The default time when the device reports SMS alarm is
UTC time. The user needs to configure the appropriate time difference according to the local time zone. For
example: Beijing time zone is UTC +08:00, 8*60=480 minutes, then the time difference is 480;
The time zone of Caracas is UTC – 04:30, 4*60+30=270 minutes, and the time difference is -270.

RFID Authorization card configuration

Query and add authorization card

Read (query) ID:：

Select the group first, and then click "Read" to read the RFID card number registered in the group

Add ID:
Edit the RFID card number in the edit box, select the group, select "Add", and click "Set"
25 / 38
Delete authorization card

After editing the RFID card number, select "Delete", and then click "Set" to send the instruction to delete the
edited card number. Up to 20 cards can be deleted at one time

Delete all authorization cards

To delete all, select "Delete All", click "Settings", and send instructions to delete all RFID card numbers
composed in JT701D.

Geo fence function configuration

Users in Mainland China cannot access Google Maps. Please set up the electronic enclosure area on the Joint
Cloud Platform.
Step1: Click “Geo-fence setting”,Click “Load map” to enter following interface.

Step2: Click “Start draw”, then left click corresponding area in the map as follows:

26 / 38
Step3: Click: “Finish drawing”, So finished the drawing and begin to save the setting later.
Please refer follow picture.

Step4: Click “Save” button to save setting. So the software will send geo-fence command to the JT701D device.
Explanation about other buttons:

: Read the previous geo-fence setting in the map.

: When you draw the map in wrong area, you can click this button to clear this wrong drawing.

: When the geo-fence has been set and want to change, you can click this button to delete the
geo-fence setting.

Alarm configuration

Alarm type and conditions

Support 9 kinds of alarms:：

① Lock rope cut off: When the equipment is in the locked state, if the rope is cut, an alarm data will be
generated.
② Swiping unauthorized RFID card: Swiping the card with an unregistered card will generate an alarm data.
③ Long unlocking: When the device is unlocked for a long time, an alarm data will be generated.
④ Enter the static password incorrectly for 5 consecutive times: When the static and dynamic password is
unlocked incorrectly for 5 consecutive times, an alarm data will be generated.
⑤Enter the fence: the device enters the fenced area from outside the fence, and an alarm for entering the
fence is generated.
⑥Leaving the fence: The device leaves the fenced area and generates a fence alarm;
⑦ Low battery: If it is less than 30% (default, can be modified) for more than 10 minutes, a low battery alarm
is considered.
⑧Motor stuck: When the motor is stuck, an alarm data will be generated.
⑨The back cover is open: When the device detects that the back cover is open, an alarm data is triggered.

27 / 38
Configure Alarm channel switch

By default, the device opens all GPRS channels for alarms.

All Close: Close GPRS and SMS channel alarm;
GRPS: open GPRS channel alarm;
SMS: Turn on SMS channel alarm;
All Open: Open GPRS and SMS channel alarm;

Read: Read the previous configuration

Write: Write the current configuration

Edit command configuration interface

When the user proposes a customized function for the product and adds related instructions, the configuration
software fails to meet the customer's customized needs. The user can edit the instruction of the customized
function by himself, and issue the instruction through this interface.

28 / 38
Product peripherals -JT126 temperature and humidity
sensor

JT126 Introduction

The JT126 wireless temperature and humidity sensor can be matched with the JT701D smart electronic lock to
upload the current temperature and humidity of the detected item to the platform, which is convenient for
managers to discover in time whether the ambient temperature and humidity meet the requirements of the item
storage Relevant regulations, and timely adjustments.

JT126 Technical parameters

Item Description
Dimension 100mm*60mm*17mm

Weight about 80 g
Housing material PC engineer plastic
IP Rated IP65

Working temperature -40℃ -- +60℃

Storage temperature -40℃ -- +70℃
Relative humidity 5%—95%
Working current <30mA on average

<10uA in standby

Battery 2400mAh，3.0V Disposable lithium manganese batteries

Battery life ＞1 year （data uploading interval 5 minutes）
Measuring temperature ±1℃
accuracy
Measuring temperature -40℃~+80℃
range

29 / 38
 Measuring humidity ±2%RH
accuracy
Measuring humidity range 0 %RH ~100%RH
Data cache ＞2500 pieces

JT126 Power on and power off

Status Operate Indicator status

Power on Press and hold the power button for 2 The green light flashes, means power on
seconds until the green light flashes
Power off Press and hold the power button for 2 The red light flashes, means power off
seconds until the red light flashes
Status Press the power button for 0.5 second The green light flashes, means power on
check Press the power button for 0.5 second The red light flashes, means power off

Bind JT126 temperature and humidity sensor with JT701D

Enter the 10-digit ID of JT126 into the JT701 binding temperature and humidity sensor label interface, click "Bind
Flags", the binding is successful, the JT701D device, the buzzer will

prompt.

Unbind JT126 temperature and humidity sensor from JT701D

Click "Clear Flags" to unbind all bound JT126

30 / 38
 peripherals

Product Peripherals -JT709 Bluetooth slave lock

JT709 Introduction

JT709 smart Bluetooth lock is a slave lock product developed on the basis of the existing product JT701 smart
electronic lock. JT701D is the master lock and JT709BL is the slave lock. It can be applied to container/tank truck
with one master and multiple slaves (multiple Door/multi valve) management application scenarios. Supporting
remote change of product configuration parameters, with rechargeable lithium battery, it can be used repeatedly.
Provide high-precision asset timing tracking information through the master lock JT701D, and support remote
online and on-site Bluetooth offline unlocking methods, support real-time monitoring and historical track playback,
lock status and other real-time tracking information on different platforms. It provide customers with lower costs,
safer, more efficient and smarter mobile assets management solution.

JT709 Technical parameters

Item Description
Dimension 110mm*82mm*35mm

31 / 38
 Weight about 500 g
Housing material Nylon and glass fiber
IP Rated IP67

Working temperature -30℃- - +70℃

Storage temperature -40℃- - - +85℃
Relative humidity 5%—95%
Working current <100mA on average

<60uA in standby

Battery 3000mAh , (3.7v) Rechargeable lithium battery

Data cache 1536 pieces
Unlocking ways Unlock via Bluetooth in APP

Unlock via command from master lock JT701D

Bind JT709 with JT701D

The last 10 digits (numbers + letters) of the 12-digit number under the JT709 QR code are the device ID. For
example, if the number is 00E017150000, the device ID is E017150000.
Enter the device ID into the JT701 binding temperature and humidity sensor label interface, click "Bind Flags", the
binding is successful, the JT701D device, the buzzer will prompt.

Unbind JT709 from JT701D

Click "Clear Flags" to unbind all the previously bound JT709 Bluetooth slave locks.

32 / 38
33 / 38
To use the device in Jointech Cloud
platform

Login

Please contact the sales to get login account in Jointech platform.

Manage your asset in the platform

Login Url: https://icloud.assetscontrols.com:1443/

Please refer the software operation manual to register new devices, monitoring,view tracks etc.
The picture below is the screenshot of monitoring

Device and its Peripherals’ installation

JT701D’s installation

Easy to install, attach and lock.

34 / 38
JT126 Temperature & Humidity sensor’s installation.

Switch on JT126, place it with the asset to be monitored.

If there is water in place, please protect the sensor from water, the sensor cannot soak in water.

35 / 38
JT709 Bluetooth Slave Lock’s installation

36 / 38
Device Maintenance
The dirt, mud may penetrate from lock hole in long time outdoor use and cause device malfunction, the users
is required to clean the device regularly, to help the device work for long.
The maintenance steps is as below:
1. Clean the dirt or debris on the surface of the equipment.
2. Pull out the lock rope and wipe both ends of the lock rope with a clean cloth
3. Use a clean cotton swab or other tools to clean the lock hole inside..

Trouble Shooting
Question 1 The device cannot start
Answer： Battery low;
Power switch was disabled

Solution: Power used out, charge the device；

Connect the device to computer, enable the power switch from configure
software.

Question 2： First use, cannot connect to platform

Answer： The problem may from below:
The device IP, Port, APN setting is not correct;
Low power, the device is in deep sleep mode；
SIM credit not enough, not data；
The GPRS is not activated in SIM；
There is PIN code required for SIM
Solution: Write the correct IP, Port, APN from configure software.
Put the sim card to another JT701 device, to confirm if the sim card
working. (there is credit and GPRS activated).
Swipe card, check if the yellow indicator blinks, and charge the device.

Question 3: Failed to unlock remotely from platform

Answer： Check if the device is online.
If it is offline, please refer Question 2
Solution Please swipe card or vibrate it to wake up device.

Question 4：Battery died, cannot unlock

Answer： Please charge the device in the field
Solution The users can charge the device with power bank,
5V input. Charge for 30 minutes and swipe to unlock

37 / 38
Contact us
Hotline：400-183-0755
Telephone：0755-83236778 83237778
Address: 3/F,T4 , Hi Park, Luozu Community, Shiyan Street, Baoan District, Shenzhen, China
Fax: 0755-26493511
Email:jointech001@vip.sina.com

38 / 38