03 SPECIFICATIONS :

Weight:
05 07
04 06 - Objective Weight : 422 ± 10 gr

+0.07
0
+0.3 12
5.3 0

0.1 P1 A

+0.7
NOTE BOARD
(lamage)

0.2 B
11

0
spot face
13
Refer to technical specification 01492_13_00440

13.2 H10
A

0.3 P1 A B
10.7
B
B3
EJECTOR
(Specific IRAN specification 01492_15_00200)

0.2 P1
- Exceptionnal loads Following standard PSA B32 0731

+0.7
0
B - Max loads: No plastic deformation allowed.
+0.07

10.7
No plastic deformation and no sliding allowed for gearbox mounting
0

ZP
0.1 P1 C

- Durability loads: according to standard PSA B32 0730

13.2 H10

A B2 Durability load validation:

Test start with a locati (part No. 0) under KFN stress
XP
YP K coefficient must be define with PSA agreement
x3 350 mm² min zone - Crash behavior
On Support area
Front view Isometric view Specifications According to load table
B1
Calculation and test According to protocal
+0.7

0.2 A
B No break at the interfaces - no buckling
0
02

min 5
01 10.7 Section view B-B
2X 0.75 ±0.25 45 37
A - Durability test, test and Exceptionnal breaking must be Realized:
08 - For Each cavity
- For Each new mold
Section view A-A 09 10 22 - For Each design modification affecting the part resistance
Point A
49.5 minimum fitting Insulator center
Tests-have to be realiezd with the SMID

21 - Bosses resistance
Under load Corresponding to the maximum tension of the screw, applied in Z-
5.5 ±0.5
RHS Engine Mount fitting area on a H RCN screw head, bosses must not have plastic deformation For Each
(No rubs, parting, marks... are allowed) X3 Under screw head
position of the screw in the boss. At the end of the test, tappings must not be
.1

EJECTOR 14 1 P1
damaged.
±0

0.3 P1 15
20

- Material

30
20 19
X3 R12.5 AC
16 AS7G03 TYPE 2 Y3 3 According to STD ( B54 1120)
For the 3 washer or Screwhead supporting
Y Y
- Cleanliness of contact areas
±0.15

30
17 X3 R6.3 AC Bearing surfaces must-have not burr, chips, impact, welding ...
45.42

23
Support area B1 , B2 , B3
Organic pollution is prohibited (oil ...)
P1 Surface tension - 27.3mN / m according to standard ISO 8296
0.1 CZ B1 B2 B3 18
- The hand must not be dangerous (burr, cutting edge ...)
Top view - Supplier 3D must be included in PSA 3D
- General dimension: ISO 2768-m

PRODUCT MARKING AREA (normes PSA A10 2260 and B20 0110) :
SUPPLIER MARKING :
Production month / batch referring to ISO 8061 standard. 60.7
Supplier code (10 digit COFOR) or DUNS number(international 9 digit identifier)
or Supplier logo.
PARTING LINE

27
C 0.5 28
24

4X R 2 Y

45.4
16.6

0.5 YY

51
-0.2
-0.4

26 34
X X 33
28

C Y
point 1 29 36 ±0.25
C
25 0.5 XX Length x Width x Height : EJECTOR
79.6 Insulator center 31 32
30 29.7 x 3.3 x 0.4 25
24 0.5 A B P1
Section view C-C
35 27 min (X3)

36

01.02.2023 M.Nasrollahi Dimensions of No.23, No.33, No.34, No.35 & No.37 was changed and M.Vaziri
important
19.05.2021 S.Ahmadi Tolerance of Dimention 31 has been changed from 0/-0.3 to -0.2/-0.4 H.Monfared
Loads definition : 13.04.2021 S.Ahmadi Tolerance of Dimention 31 has been changed from -0.25/+0.25 to 0/-0.3 H.Monfared
application area 2D:
efforts by Fz 1- Part number was added on the drawing
Type Load definition 2- Bill of materials was added with mass and materials designations
Fx-
Axis Fatigue Equivalent Maximum load Exceptional load with Standards corresponding to the material of each component
10^6 cycles (pure (N) (N) 3- Marking with details (information’s, police type, police size,
dynamic) B precise location,) Logos, was added to the drawing.
10.02.2017 R.Seifi
(N) PIN 2 A.Amini 4- CTF itmes in Notes Sheet was added.
5- Tolerance was added to the objective mass
3D:
SMOD X ± 1201 ± 2682 ± 6113
1- jectors and marking was added to 3D model
Y ± 2192 ± 5438 ± 7040

A break of the right bracket and junctions for a load lower than Fz Fx+ DATE NAME DESCRIPTION APP.
(applied on elastic center) is strictly forbidden. PIN 1
TITLE: PART LASTIC CO.
CHENARAN-MASHAD-IRAN
X Y Z A PT RH UPR Elastic Support EC5 P.O.BOX: 93615-199
Deceleration load case
TEL: +98 (582) 623 91 70
+12 000 < F _ _ FAX : +98 (582) 623 91 71
application area
efforts by Fx
VEH: K132
Fz-
- 30000 < F _ Designed by Drawn by Approved by/date Ist ANGLE
load case _ Checked by General Tol:
......... H.MONFARED
A.AMINI R.SEIFI See DWG
F = held load applied on elastic center (in N) 18/07/2017
P1
Product Code:
Part No: Material: Scale
Fz+ 8661084
1:1
standard directory 9802174180 See DWG
PSA A10 2260 PSA A32 4115 PSA B15 5220 PSA B200250 PSA A12 5510 Unit
Customer: SAPCO mm
PSA A32 4110 PSA32 4250 PSA A50 0110 PSA B15 4101 PSA B154102
ISO 2768-m AS7G03 TYPE 2 Y3 3 PSA B20 0110 PSA B20 0200 PSA B20 1220 PSA B32 0730 PSA B32 0731 S Original
9802174180 422 ±10 gr According to STD ( B54 1120) PSA B51 1110 PSA B51 1130 PSA B54 1120 PSA B72 3720 PSA D17 1058 Customer Dwg No: 9680138380 R A0
PART NAME PART No. WEIGHT STANDARD MATERIAL DEX ISO 1 DEX ISO 1101 DEX ISO 129-1 DEX ISO 14405-1 DEX 2768-2 Sheet
DEX ISO 286-1 DEX ISO 286-2 DEX ISO 5459 DEX ISO 8601 DEX ISO 8015 Filename/Add: L:\DRAWING Doc.Code: 8661084A60AE
7/14
CRITICAL CUSTOMER SPECIAL C P.L.SPECIAL P IMPORTANT MINOR:NO SIGN