Scribd
Upload
8 views1 page

Untitled 4

Carbocoat 115 is a fast-drying modified alkyd primer designed for corrosion protection on structural steel, suitable for fabrication shops. It features rapid cure times, good filling properties, and is VOC compliant, available in red and grey colors. The primer can be topcoated with acrylics or alkyds and requires clean, dry surfaces for optimal adhesion.

Uploaded by

Longtomahawk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
8 views1 page

Untitled 4

Carbocoat 115 is a fast-drying modified alkyd primer designed for corrosion protection on structural steel, suitable for fabrication shops. It features rapid cure times, good filling properties, and is VOC compliant, available in red and grey colors. The primer can be topcoated with acrylics or alkyds and requires clean, dry surfaces for optimal adhesion.

Uploaded by

Longtomahawk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

®

Carbocoat 115
PRODUCT DATA SHEET

S E L E C T I O N & S P E C I F I C AT I O N D ATA
Generic Type Modified Alkyd Primer

Fast drying steel primer that provides corrosion protection on structural steel. Well suited for
Description fabrication shops that need fast cure to dry and handle times. May be topcoated with conventional
alkyds or acrylics for color, aesthetics or additional protection.

• Rapid cure
• VOC compliant for most areas
Features
• Good for filling properties on rough and pitted steel
• Fast dry to handle properties

Color Red (0500), Grey (0700)

Finish Flat

1.5 - 2 mils (38 - 51 microns) per coat


Dry Film Thickness
Don't exceed 3.0 mils in a single coat.

Solids Content By Volume 51% +/- 2%

818 ft²/gal at 1.0 mils (20.1 m²/l at 25 microns)


Theoretical Coverage 545 ft²/gal at 1.5 mils (13.4 m²/l at 38 microns)
Rate 409 ft²/gal at 2.0 mils (10.0 m²/l at 50 microns)
Allow for loss in mixing and application.

As Supplied : 3.50 lbs./gal (419 g/l)


Thinner 10 : 6 oz/gal 3.65 lbs./gal (437 g/l)
VOC Values
These are nominal values and may vary slightly with color.

Continuous: 200°F (93°C)


Non-Continuous: 250°F (121°C)
Dry Temp. Resistance
Discoloration and loss of gloss are observed above 200 °F (93 °C).

Topcoats May be coated with Acrylics or Alkyds depending on exposure and need.

S U B S T R AT E S & S U R F A C E P R E PA R AT I O N
Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other
General
contaminants that could interfere with adhesion of the coating.

SSPC-SP6 with a 1.0-2.0 mil (25-50 microns) surface profile for maximum protection. SSPC-SP2 or
SP3 as minimum requirement.
Steel
When using under fireproofing products, defer to the primer surface preparation requirements in the
product data sheet of the fireproofing product

MIXING & THINNING


Mixing Power mix until uniform in consistency.

October 2023 0801 Page 1 of 3

You might also like