UN38.

3 检测报告
UN38.3 Test Report
Client Shenzhen Browiner Tech Co., Ltd
委托方 深圳市宝润科技有限公司

Room 501, Building C, Ganghongji High-Tech Intelligent Industrial Park,

No.1008, Songbai Road, Yangguang Community, Xili Street,
Add. of Client
NanshanDistrict, 518055 Shenzhen, PEOPLE'S REPUBLIC OF CHINA
委托方地址 深圳市南山区西丽街道阳光社区松白路 1008 号港鸿基高新智能产业园 C 栋
501
Samples Description Lithium Ion Battery
样品名称 锂离子电池

Model/Type
BRL1010B-15A
型号规格
Shenzhen NCT Testing Technology Co., Ltd.
深圳诺测检测技术有限公司
B2A101/B2A201/B2A202, Fuqiao 6th Area, Xintian, Fuhai Subdistrict,
Testing Laboratory Bao'an District, Shenzhen, Guangdong, China
测试机构 广东省深圳市宝安区福海街道新田社区富桥六区 B2A101, B2A201, B2A202
Phone number 电话号码: +86-755-23218380
Email 邮箱: sales@nct-testing.com
Website 网址: http://www.ncttesting.cn
Report No.
NCT24025466B1-1
报告编号
Issued Date
2024.07.25
发行日期
Test Conclusion 测试结论:
Shown in the Conclusion of test report. 见检测报告结论页.

Tested by 主检人: Approved by 批准人:

(Testing Engineer 测试工程
(Technical Director 技术总监)
师) Miller Gao 高依翔 Boris Lin 林博谋
Seal of NCT 报告单位（盖章）
Inspected by 审核人:
(Battery manager 电池组经
理) Miya Li 李志双 Date of Issue 签发日期: 2024.07.25

Report No. 报告编号: NCT24025466B1-1 Page 1 of 22 第 1 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Ⅰ、Sample Description 样品描述

Sample
Product Name Lithium Ion Battery
Model BRL1010B-15A
产品名称 锂离子电池
样品型号
Manufacturer Shenzhen Rising-more Technology Co., Ltd.
制造商 深圳市瑞森木科技有限公司
Manufacturer’s Room 602, Building 2, Row 1, Heshuikou New Village, Heshuikou Community,
Address Matian Street, uangming District, Shenzhen
制造商地址 深圳市光明区马田街道合水口社区合水口新村一排 2 栋 602
Factory Shenzhen Rising-more Technology Co., Ltd.
工厂 深圳市瑞森木科技有限公司
Room 602, Building 2, Row 1, Heshuikou New Village, Heshuikou Community,
Address
Matian Street, uangming District, Shenzhen
地址 深圳市光明区马田街道合水口社区合水口新村一排 2 栋 602
Manufacturer’s Phone number E-mail address Website
contact 电话号码 电子邮箱地址 网址
information
制造商联系信息 +86-15112669276 359747539@qq.com ---

Battery Size
Trade Mark Cell Shape Cylindrical (132.0 × 85.3 ×
--- 电池尺寸
商标 电芯形状 圆柱形 26.0)mm
(L×W×T)
Limited
Nominal Rated
9.8Ah Charge
Voltage 10.95V Capacity 12.6V
107.31Wh Voltage
标称电压 额定容量
充电限制电压
Maximum
Continuous
Standard End Charge
Charge
Charge Current 1960mA Current 4900mA Current 100mA
标准充电电流 结束充电电流
最大持续充电
电流
Standard Maximum
Cut-off Voltage Discharge Discharge
8.4V 1960mA 12000mA
放电截止电压 Current Current
标准放电电流 最大放电电流
Cell Number Cell Model
6PCS INR21700-50G
组成电芯数量 电芯型号
Sample
Sample Mass Physical Approximate Blue Cuboid
497.8g
样品重量 description 蓝色近长方体
样品物理形态
Completing
Receiving Date
2024.06.07 Date 2024.06.28
接收日期
完成日期

Report No. 报告编号: NCT24025466B1-1 Page 2 of 22 第 2 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Ⅱ、Standard 标准
UNITED NATIONS “Manual of Tests and Criteria” (ST/SG/AC.10/11/Rev.7+Amend.1 Section 38.3)

联合国《试验和标准手册》第七修订版及修正 1 第 38.3 节。

Ⅲ、Test Item 测试项目

T.1. Altitude simulation 高度模拟 T.5. External short circuit 外部短路
T.2. Thermal test 温度试验 T.6. Impact 撞击/ Crush 挤压
T.3. Vibration 振动 T.7. Overcharge 过充电
T.4. Shock 冲击 T.8. Forced discharge 强制放电

Ⅳ、Test Method and Requirement 测试方法和要求

Tests T.1 to T.5 shall be conducted in sequence on the same cell or battery. Tests T.6 and T.8 shall
be conducted using not otherwise tested cells. Test T.7 may be conducted using undamaged batteries
previously used in tests T.1 to T.5 for purposes of testing on cycled batteries.
用相同的电芯或电池按照顺序进行试验 T.1 至 T.5。试验 T.6 至 T.8 用没有进行其他试验的电芯。试验
T7 可以使用原先在试验 T1 至 T5 中使用过的未损坏的电池进行，以便测试交替充电放电的电池。
Batteries of B1#~B4# 、B9#~B12# are full charged after one cycle;
Batteries of B5#~B8# 、B13#~B16# are full charged after twenty-five cycles;
Component cells of C1#~C5# are 50% charged after one cycle;
Component cells of C6#~C10# are 50% charged after twenty-five cycles;
Component cells of C11#~C20# are full discharged after one cycle;
Component cells of C21#~C30# are full discharged after twenty-five cycles;
Test environment condition: ambient temperature: 15-25℃, ambient humidity: 40-70%
电池 B1#~B4# , B9#~B12#为 1 次循环满电状态；
电池 B5#~B8#, B13#~B16#为 25 次循环满电状态；
组成电芯 C1#~C5#为 1 次循环后 50%充电状态；
组成电芯 C6#~C10#为 25 次循环后 50%充电状态；
组成电芯 C11#~C20#为 1 次循环完全放电状态；
组成电芯 C21#~C30#为 25 次循环完全放电状态；
试验环境条件：环境温度：15-25℃，环境湿度：40-70%

In order to quantify the mass loss, the following procedure is provided:

Mass loss (%) = (M1-M2)/M1 x 100
质量损失的量化值，可用以下公式计算：
质量损失(%)=(M1-M2)/M1×100
Where M1 is the mass before the test and M2 is the mass after the test. When mass loss does not
exceed the values in Table below, it shall be considered as "no mass loss".
式中：M1 是试验前的质量，M2 是试验后的质量。如果质量损失不超过下表所列的数值，应视为“无质
量损失”。

Report No. 报告编号: NCT24025466B1-1 Page 3 of 22 第 3 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Mass M of cell or battery Mass loss limit

电芯或电池的质量 质量损失限值
M＜1g 0.5%
1g≤M≤75g 0.2%
M＞75g 0.1%
Leakage means the visible escape of electrolyte or other material from a cell or battery or the loss of
material (except battery casing, handling devices or labels) from a cell or battery such that the loss of mass
exceeds the values in Table above.
渗漏系指可以看到的电解液或者其他物质从电芯或者电池中漏出，或电芯或电池中的物质损失（不包括
电池外壳、搬运装置、或标签），失去的质量超过上表所列的数值。
In test T.1 to T.4, cells and batteries meet this requirement if there is no leakage, no venting, no
disassembly, no rupture and no fire and if the open circuit voltage of each test cell or battery after testing is
not less than 90% of its voltage immediately prior to this procedure. The requirement relating to voltage is
not applicable to test cells and batteries at fully discharged states.
在测试 T.1 至 T.4 中，电芯和电池须满足无渗漏、无泄气、无解体、无破裂和无起火，并且每个试验电
芯或电池在试验后的开路电压不小于其在进行这一试验前电压的 90%。

T.1. Altitude simulation 高度模拟

Test method 测试方法

Test cells and batteries are stored at a pressure of 11.6 kPa or less for at least six hours at ambient
temperature (20±5℃).
试验电芯和电池被放置在压力等于或低于 11.6 kPa 和环境温度(20±5℃)下存放至少 6 小时。
Requirement 要求
Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no
rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than
90% of its voltage immediately prior to this procedure.
电芯和电池须无渗漏、无泄气、无解体、无破裂和无起火，并且每个试验电芯或电池在试验后的开路电
压不小于其在进行这一试验前电压的 90%。

T.2. Thermal test 温度试验

Test method 测试方法

Test cells and batteries are to be stored for at least six hours at a test temperature equal to 72±2℃,
followed by storage for at least six hours at a test temperature equal to -40±2℃. The maximum time
interval between test temperature extremes is 30 minutes. This procedure is to be repeated until 10 total
cycles are complete, after which all test cells and batteries are to be stored for 24 hours at ambient
temperature (20± 5℃). For large cells and batteries the duration of exposure to the test temperature
extremes should be at least 12 hours.
试验电芯和电池放置在试验温度等于 72±2℃的条件下存放至少 6 小时，接着再在试验温度等于-40±2℃
的条件下存放至少 6 小时。两个极端试验温度之间的最大时间间隔为 30 分钟。此程序重复进行，共完成 10
次循环，接着将所有试验电芯和电池在环境温度(20±5℃)下存放 24 小时。对于大型电芯和电池，暴露于极
端试验温度的时间至少应为 12 小时。
Requirement 要求
Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no
rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than
90% of its voltage immediately prior to this procedure.

Report No. 报告编号: NCT24025466B1-1 Page 4 of 22 第 4 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
电芯和电池须无渗漏、无泄气、无解体、无破裂和无起火，并且每个试验电芯或电池在试验后的开路电
压不小于其在进行这一试验前电压的 90%。

T.3. Vibration 振动

Test method 测试方法

Cells and batteries are firmly secured to the platform of the vibration machine without distorting the
cells in such a manner as to faithfully transmit the vibration. The vibration shall be a sinusoidal waveform
with a logarithmic sweep between 7 Hz and 200 Hz and back to 7 Hz traversed in 15 minutes. This cycle
shall be repeated 12 times for a total of 3 hours for each of three mutually perpendicular mounting
positions of the cell. One of the directions of vibration must be perpendicular to the terminal face.
电芯和电池紧固于振动台台面，但不得造成电芯变形，并能准确可靠地传播振动。振动应是正弦波形，
对数扫描频率在 7 Hz 和 200 Hz 之间，再回到 7 Hz，跨度为 15 分钟。这一振动过程须对三个互相垂直的电
芯安装方位的每一方向重复进行 12 次，总共为时 3 小时。其中一个振动方向必须与端面垂直。
The logarithmic frequency sweep shall differ for cells and batteries with a gross mass of not more than
12 kg (cells and small batteries), and for batteries with a gross mass of more than 12 kg (large batteries).
作对数式频率扫描，对电芯和总质量不超过 12 千克的电池（电芯和小型电池），和对质量超过 12 千克
的电池（大型电池）有所不同。
For cells and small batteries : from 7 Hz a peak acceleration of 1 gn is maintained until 18 Hz is
reached. The amplitude is then maintained at 0.8 mm (1.6 mm total excursion) and the frequency
increased until a peak acceleration of 8 gn occurs (approximately 50 Hz). A peak acceleration of 8 gn is
then maintained until the frequency is increased to 200 Hz.
对电芯和小型电池：从 7 Hz 开始，保持 1 gn 的最大加速度，直到频率达到 18 Hz。然后将振幅保持在
0.8mm（总位移 1.6mm），并增加频率直到峰值加速度达到 8 gn（频率约为 50 Hz）。将峰值加速度保持
在 8 gn 直到频率增加到 200 Hz。
For large batteries : from 7 Hz a peak acceleration of 1 gn is maintained until 18 Hz is reached. The
amplitude is then maintained at 0.8 mm (1.6 mm total excursion) and the frequency increased until a peak
acceleration of 2 gn occurs (approximately 25 Hz). A peak acceleration of 2 gn is then maintained until the
frequency is increased to 200 Hz.
对大型电池：从 7 Hz 开始，保持 1 gn 的最大加速度，直到频率达到 18 Hz。然后将振幅保持在 0.8mm
（总位移 1.6mm），并增加频率直到峰值加速度达到 2 gn（频率约为 25Hz）。将峰值加速度保持在 2 gn
直到频率增加到 200 Hz。
Requirement 要求
Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no
rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than
90% of its voltage immediately prior to this procedure.
电芯和电池须无渗漏、无泄气、无解体、无破裂和无起火，并且每个试验电芯或电池在试验后的开路电
压不小于其在进行这一试验前电压的 90%。

T.4. Shock 冲击

Test method 测试方法

Test cells and batteries shall be secured to the testing machine by means of a rigid mount which will
support all mounting surfaces of each test battery.
试验电芯和电池用刚性支架紧固在试验装置上，支架支撑着每个试验电池的所有安装面。
Each cell shall be subjected to a half-sine shock of peak acceleration of 150 gn and pulse duration of
6 milliseconds. Alternatively, large cells may be subjects to a half-sine shock of peak acceleration of 50 gn
and pulse duration of 11 milliseconds.
每个电芯须经受峰值加速度 150 gn 和脉冲持续时间 6 ms 的半正弦波冲击。不过，大型电芯须经受峰值
加速度 50 gn 和脉冲持续时间 11 ms 的半正弦波冲击。

Report No. 报告编号: NCT24025466B1-1 Page 5 of 22 第 5 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
Each battery shall be subjected to a half-sine shock of peak acceleration depending on the mass of
the battery. The pulse duration shall be 6 milliseconds for small batteries and 11 milliseconds for large
batteries. The formulas below are provided to calculate the appropriate minimum peak accelerations.
每个电池须经受半正弦波冲击，峰值加速度需要根据电池的重量来决定。小型电池的脉冲持续时间为 6
ms，大型电池的脉冲持续时间为 11ms。下面的公式是用来计算合适的最小峰值加速度。

电池 最小峰值加速度 脉冲持续时间
小型电池 150 gn 或计算结果中取最小的值 6ms
100850
加速度（gn）= ( )
mass

大型电池 50 gn 或计算结果中取最小的值 11 ms
30000
加速度（gn）= ( )
mass

Each cell or battery shall be subjected to three shocks in the positive direction and to three shocks in
the negative direction in each of three mutually perpendicular mounting positions of the cell or battery for a
total of 18 shocks.
每个电芯或电池须在三个互相垂直的电芯或电池安装方位的正方向经受三次冲击，接着在反方向经受三
次冲击，总共经受 18 次冲击。
Requirement 要求
Cells and batteries meet this requirement if there is no leakage, no venting, no disassembly, no
rupture and no fire and if the open circuit voltage of each test cell or battery after testing is not less than
90% of its voltage immediately prior to this procedure.
电芯和电池须无渗漏、无泄气、无解体、无破裂和无起火，并且每个试验电芯或电池在试验后的开路电
压不小于其在进行这一试验前电压的 90%。

T.5. External short circuit 外部短路

Test method 测试方法

The cell or battery to be tested shall be heated for a period of time necessary to reach a
homogeneous stabilized temperature of 57±4℃, measured on the external case. This period of time
depends on the size and design of the cell or battery and should be assessed and documented. If this
assessment is not feasible, the exposure time shall be at least 6 hours for small cells and small batteries,
and 12 hours for large cells and large batteries. Then the cell or battery at 57± 4℃ shall be subjected to
one short circuit condition with a total external resistance of less than 0.1 ohm.
试验电芯或电池需要加热一段时间，以使其外壳温度均匀稳定地达到 57±4℃。加热时间的长短是由电
芯或电池的尺寸和设计来决定的，这个加热时间需要评估并记录。如果这个加热时间不好评估的话，对于小
电芯和小电池需要在此温度下放置至少 6 个小时，对于大电芯和大电池至少放置 12 个小时。然后使电芯或

Report No. 报告编号: NCT24025466B1-1 Page 6 of 22 第 6 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
电池在 57±4℃下经受总外电阻小于 0.1Ω 的短路条件。
This short circuit condition is continued for at least one hour after the cell or battery external case
temperature has returned to 57±4℃, or in the case of the large batteries, has decreased by half of the
maximum temperature increase observed during the test and remains below that value.
短路测试持续到电芯或电池外壳温度回到 57±4℃后至少持续 1 小时，针对大电池，外壳温度需要下降
到测试过程中监控到的最大温度的一半以下。
The short circuit and cooling down phases shall be conducted at least at ambient temperature.
短路测试和冷却阶段至少应该在环境温度下进行。
Requirement 要求
Cells and batteries meet this requirement if their external temperature does not exceed 170℃ and
there is no disassembly, no rupture and no fire during the test and within six hours after test.
电芯和电池外壳温度不超过 170℃，并且在试验过程中及试验后 6 小时内无解体、无破裂，无起火。

T.6. Impact / Crush 撞击/挤压

Test procedure – Impact (applicable to cylindrical cells not less than 18.0 mm in diameter)
测试步骤 – 撞击（适用于直径大于等于 18.0 毫米以上的圆柱形电芯）
The test sample cell or component cell is to be placed on a flat smooth surface. A 15.8 mm ± 0.1mm
diameter, at least 6 cm long, or the longest dimension of the cell, whichever is greater, Type 316 stainless
steel bar is to be placed across the centre of the sample. A 9.1 kg ± 0.1 kg mass is to be dropped from a
height of 61 ± 2.5 cm at the intersection of the bar and sample in a controlled manner using a near
frictionless, vertical sliding track or channel with minimal drag on the falling mass. The vertical track or
channel used to guide the falling mass shall be oriented 90 degrees from the horizontal supporting surface.
试样电芯或电芯组件放在平坦光滑表面上，一根 316 型不锈钢棒横放在试样中心，钢棒直径 15.8 毫米
±0.1 毫米，长度至少 6 厘米，或电芯最长端的尺度，取二者之长者。将一块 9.1 千克±0.1 千克的重锤从
61±2.5 厘米高度跌落到钢棒和试样交叉处，使用一个几乎没有摩擦的、对落体重锤阻力最小的垂直轨道或管
道加以控制。垂直轨道或管道用于引导落锤沿与水平支撑表面呈 90 度落下。
The test sample is to be impacted with its longitudinal axis parallel to the flat surface and
perpendicular to the longitudinal axis of the 15.8 mm ± 0.1mm diameter curved surface lying across the
centre of the test sample. Each sample is to be subjected to only a single impact.
受撞击的试样，纵轴应与平坦表面平行并与横放在试样中心的直径 15.8±0.1 毫米弯曲表面的纵轴垂
直。每一试样只经受一次撞击。

Test procedure – Crush (applicable to prismatic, pouch, coin/button cells and cylindrical cells less than
18.0 mm in diameter)
测试步骤– 挤压（适用于棱柱形，袋状，硬币/纽扣电芯和圆柱形电芯直径小于 18.0 毫米）
A cell or component cell is to be crushed between two flat surfaces. The crushing is to be gradual with
a speed of approximately 1.5 cm/s at the first point of contact. The crushing is to be continued until the first
of the three options below is reached.
将电芯或电芯组件放在两个平面之间挤压，挤压力度逐渐加大，在第一个接触点上的速度大约为 1.5
cm/s。挤压持续进行，直到出现以下三种情况之一：
(a) The applied force reaches 13 kN ± 0.78 kN;
(b) The voltage of the cell drops by at least 100 mV;
(c) The cell is deformed by 50% or more of its original thickness.
(a)施加的力达到 13 kN ± 0.78 kN；
(b)电芯的电压下降至少 100mV；
(c)电芯形变达到原始厚度的 50%或更多。
Once the maximum pressure has been obtained, the voltage drops by 100 mV or more, or the cell is
deformed by at least 50% of its original thickness, the pressure shall be released.

Report No. 报告编号: NCT24025466B1-1 Page 7 of 22 第 7 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
一旦达到最大压力、电压下降 100mV 或更多，或电芯形变至少达到原始厚度的 50%，即可解除压
力。
A prismatic or pouch cell shall be crushed by applying the force to the widest side. A button/coin cell
shall be crushed by applying the force on its flat surfaces. For cylindrical cells, the crush force shall be
applied perpendicular to the longitudinal axis.
棱柱形或袋装电芯须从最宽的面施压。纽扣/硬币形电芯应从其平坦表面施压。圆柱形电芯应从与纵轴垂
直的方向施压。
Each test cell or component cell is to be subjected to one crush only. The test sample shall be
observed for a further 6 h. The test shall be conducted using test cells or component cells that have not
previously been subjected to other tests.
每个试样电芯或电芯组件只做一次挤压试验。试样须继续观察 6 小时。试验须使用之前未做过其他试验
的试样电芯或电芯组件进行。
Requirement 要求
Cell and component cells meet this requirement if their external temperature does not exceed 170℃
and there is no disassembly and no fire during the test and within six hours after test.
电芯和电芯组件外壳温度不超过 170℃，并且在试验过程中及试验后 6 小时内无解体，无起火。

T.7. Overcharge 过充电

Test method 测试方法

The charge current shall be twice the manufacturer's recommended maximum continuous charge
current. The minimum voltage of the test shall be as follows:
充电电流为制造商推荐的最大持续充电电流的两倍。试验的最小电压如下：
(a) When the manufacturer's recommended charge voltage is not more than 18V, the minimum
voltage of the test shall be the lesser of two times the maximum charge voltage of the battery or
22V.
(b) When the manufacturer's recommended charge voltage is more than 18V, the minimum
voltage of
the test shall be 1.2 times the maximum charge voltage.
(a) 制造商推荐的充电电压不大于 18 伏时，试验的最小电压应是电池最大充电电压的两倍或 22 伏两
者中的较小者。
(b) 制造商推荐的充电电压大于 18 伏时，试验的最小电压应是电池最大充电电压的 1.2 倍。
Tests are to be conducted at ambient temperature. The duration of the test shall be 24 hours.
试验应在环境温度下进行。进行试验的时间应为 24 小时。
Requirement 要求
Rechargeable batteries meet this requirement if there is no disassembly and no fire during the test
and within seven days after the test.
充电电池应在试验过程中和试验后 7 天内无解体，无起火。

T.8. Forced discharge 强制放电

Test method 测试方法

Each cell shall be forced discharged at ambient temperature by connecting it in series with a 12V D.C.
power supply at an initial current equal to the maximum discharge current specified by the manufacturer.
每个电芯在环境温度下与 12V 直流电电源串联在起始电流等于制造商给定的最大放电电流的条件下强制
放电。
The specified discharge current is to be obtained by connecting a resistive load of the appropriate size
and rating in series with the test cell. Each cell is forced discharged for a time interval (in hours) equal to its

Report No. 报告编号: NCT24025466B1-1 Page 8 of 22 第 8 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
rated capacity divided by the initial test current (in ampere).
试样电芯与一个适当大小的电阻负载串联以调节到规定大小的放电电流。每个电芯的放电时间（单位为
h）等于电芯的额定容量除以试验初始放电电流（单位 A）。
Requirement 要求
Primary or rechargeable cells meet this requirement if there is no disassembly and no fire during the
test and within seven days after the test.
原电芯或充电电芯应在试验过程中和试验后 7 天内无解体，无起火。

Report No. 报告编号: NCT24025466B1-1 Page 9 of 22 第 9 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Ⅴ、Test Procedure 测试流程

Marking
标识样品

Pretreatment
预处理

Samples of 样品 Samples of 样品 Samples of 样品 Samples of 样品

B01#~B08# C01#~C10# B09#~B16# C11#~C30#

Altitude simulation
高度模拟

Thermal test
温度试验

Vibration Impact / Crush Overcharge Forced discharge

振动 撞击/挤压 过度充电 强制放电

Shock
冲击

External short circuit

外部短路

Finished test
完成测试

Report No. 报告编号: NCT24025466B1-1 Page 10 of 22 第 10 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Ⅵ、Test Data 测试数据

T.1 Altitude simulation 高度模拟

Pre-test 试验前 After test 试验后 Mass Voltage after

loss test/Voltage
No. Mass Voltage Mass Voltage Status
pre-test
编号 质量 电压 质量 电压 质量损失 结果
试验后电压/试
(g) (V) (g) (V) (%) 验前电压(%)
B01 496.27 12.539 496.26 12.532 0.002 99.944 Pass 合格

B02 495.92 12.542 495.90 12.535 0.004 99.944 Pass 合格

B03 494.32 12.544 494.30 12.535 0.004 99.928 Pass 合格

B04 497.28 12.538 497.27 12.526 0.002 99.904 Pass 合格

B05 495.48 12.537 495.46 12.528 0.004 99.928 Pass 合格

B06 496.39 12.541 496.38 12.535 0.002 99.952 Pass 合格

B07 495.57 12.543 495.55 12.534 0.004 99.928 Pass 合格

B08 497.81 12.536 497.80 12.524 0.002 99.904 Pass 合格

No. B01-B04: At first cycle, in fully charged states
编号 B01-B04: 第 1 个充电周期，完全充电状态
No. B05-B08: After 25 cycles ending in fully charged states
编号 B05-B08: 第 25 个充电周期，完全充电状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.2 °C

After the test, there is no leakage, no venting, no disassembly, no rupture and no fire.
测试后，电池未渗漏、未泄气、未解体、未破裂和未起火。

Report No. 报告编号: NCT24025466B1-1 Page 11 of 22 第 11 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.2 Thermal test 温度试验

Pre-test 试验前 After test 试验后 Mass Voltage after

loss test/Voltage
No. Mass Voltage Mass Voltage Status
pre-test
编号 质量 电压 质量 电压 质量损失 结果
试验后电压/试
(g) (V) (g) (V) (%) 验前电压(%)
B01 496.26 12.532 496.23 12.412 0.006 99.042 Pass 合格

B02 495.90 12.535 495.86 12.416 0.008 99.051 Pass 合格

B03 494.30 12.535 494.27 12.412 0.006 99.019 Pass 合格

B04 497.27 12.526 497.23 12.405 0.008 99.034 Pass 合格

B05 495.46 12.528 495.42 12.408 0.008 99.042 Pass 合格

B06 496.38 12.535 496.35 12.412 0.006 99.019 Pass 合格

B07 495.55 12.534 495.51 12.416 0.008 99.059 Pass 合格

B08 497.80 12.524 497.76 12.404 0.008 99.042 Pass 合格

No. B01-B04: At first cycle, in fully charged states
编号 B01-B04: 第 1 个充电周期，完全充电状态
No. B05-B08: After 25 cycles ending in fully charged states
编号 B05-B08: 第 25 个充电周期，完全充电状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.1 °C

After the test, there is no leakage, no venting, no disassembly, no rupture and no fire.
测试后，电池未渗漏、未泄气、未解体、未破裂和未起火。

Report No. 报告编号: NCT24025466B1-1 Page 12 of 22 第 12 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.3 Vibration 振动

Pre-test 试验前 After test 试验后 Mass Voltage after

loss test/Voltage
No. Mass Voltage Mass Voltage Status
pre-test
编号 质量 电压 质量 电压 质量损失 结果
试验后电压/试
(g) (V) (g) (V) (%) 验前电压(%)
B01 496.23 12.412 496.22 12.403 0.002 99.927 Pass 合格

B02 495.86 12.416 495.85 12.405 0.002 99.911 Pass 合格

B03 494.27 12.412 494.25 12.406 0.004 99.952 Pass 合格

B04 497.23 12.405 497.22 12.397 0.002 99.936 Pass 合格

B05 495.42 12.408 495.40 12.399 0.004 99.927 Pass 合格

B06 496.35 12.412 496.33 12.401 0.004 99.911 Pass 合格

B07 495.51 12.416 495.50 12.406 0.002 99.919 Pass 合格

B08 497.76 12.404 497.74 12.396 0.004 99.936 Pass 合格

No. B01-B04: At first cycle, in fully charged states
编号 B01-B04: 第 1 个充电周期，完全充电状态
No. B05-B08: After 25 cycles ending in fully charged states
编号 B05-B08: 第 25 个充电周期，完全充电状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.3 °C

After the test, there is no leakage, no venting, no disassembly, no rupture and no fire.
测试后，电池未渗漏、未泄气、未解体、未破裂和未起火。

Report No. 报告编号: NCT24025466B1-1 Page 13 of 22 第 13 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.4 Shock 冲击

Pre-test 试验前 After test 试验后 Mass Voltage after

loss test/Voltage
No. Mass Voltage Mass Voltage Status
pre-test
编号 质量 电压 质量 电压 质量损失 结果
试验后电压/试
(g) (V) (g) (V) (%) 验前电压(%)
B01 496.22 12.403 496.20 12.396 0.004 99.944 Pass 合格

B02 495.85 12.405 495.84 12.396 0.002 99.927 Pass 合格

B03 494.25 12.406 494.23 12.394 0.004 99.903 Pass 合格

B04 497.22 12.397 497.20 12.386 0.004 99.911 Pass 合格

B05 495.40 12.399 495.39 12.392 0.002 99.944 Pass 合格

B06 496.33 12.401 496.32 12.392 0.002 99.927 Pass 合格

B07 495.50 12.406 495.48 12.396 0.004 99.919 Pass 合格

B08 497.74 12.396 497.73 12.387 0.002 99.927 Pass 合格

No. B01-B04: At first cycle, in fully charged states
编号 B01-B04: 第 1 个充电周期，完全充电状态
No. B05-B08: After 25 cycles ending in fully charged states
编号 B05-B08: 第 25 个充电周期，完全充电状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.2 °C

After the test, there is no leakage, no venting, no disassembly, no rupture and no fire.
测试后，电池未渗漏、未泄气、未解体、未破裂和未起火。

Report No. 报告编号: NCT24025466B1-1 Page 14 of 22 第 14 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.5 External short circuit 外部短路

No. Max. External Temperature Status

编号 样品表面最高温度(°C) 结果
B01 58.3 Pass 合格

B02 57.6 Pass 合格

B03 58.4 Pass 合格

B04 58.2 Pass 合格

B05 57.9 Pass 合格

B06 57.7 Pass 合格

B07 58.0 Pass 合格

B08 57.8 Pass 合格

No. B01-B04: At first cycle, in fully charged states
编号 B01-B04: 第 1 个充电周期，完全充电状态
No. B05-B08: After 25 cycles ending in fully charged states
编号 B05-B08: 第 25 个充电周期，完全充电状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.2 °C

There is no disassembly, no rupture and no fire during the test and within six hours after test.
电池在测试中和测试后 6 小时内未解体、未破裂，未起火。

Report No. 报告编号: NCT24025466B1-1 Page 15 of 22 第 15 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.6 Impact 撞击

No. Max. External Temperature Status

编号 样品表面最高温度(°C) 结果
C01 23.6 Pass 合格

C02 24.2 Pass 合格

C03 23.9 Pass 合格

C04 24.1 Pass 合格

C05 23.8 Pass 合格

C06 23.7 Pass 合格

C07 24.3 Pass 合格

C08 24.4 Pass 合格

C09 23.8 Pass 合格

C10 24.0 Pass 合格

No. C01-C05: At first cycle at 50% of the design rated capacity
编号 C01-C05: 第 1 个充放电周期 50%设计额定容量状态
No. C06-C10: After 25 cycle at 50% of the design rated capacity
编号 C06-C10: 第 25 个充放电周期 50%设计额定容量状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.3 °C

There is no disassembly and no fire during the test and within six hours after test.
电芯在测试中和测试后 6 小时内未解体、未起火。

Report No. 报告编号: NCT24025466B1-1 Page 16 of 22 第 16 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.7 Overcharge 过度充电

No. Status
编号 结果
B09 Pass 合格

B10 Pass 合格

B11 Pass 合格

B12 Pass 合格

B13 Pass 合格

B14 Pass 合格

B15 Pass 合格

B16 Pass 合格
No. B09-B12: At first cycle, in fully charged states
编号 B09-B12: 第 1 个充电周期，完全充电状态
No. B13-B16: After 25 cycles ending in fully charged states
编号 B13-B16: 第 25 个充电周期，完全充电状态

Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.3 °C

There is no disassembly and no fire during the test and within seven days after the test.
电芯在测试中和测试后 7 天内未解体，未起火。

Report No. 报告编号: NCT24025466B1-1 Page 17 of 22 第 17 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report
T.8 Forced discharge 强制放电

No. Status
编号 结果
C11 Pass 合格

C12 Pass 合格

C13 Pass 合格

C14 Pass 合格

C15 Pass 合格

C16 Pass 合格

C17 Pass 合格

C18 Pass 合格

C19 Pass 合格

C20 Pass 合格

C21 Pass 合格

C22 Pass 合格

C23 Pass 合格

C24 Pass 合格

C25 Pass 合格

C26 Pass 合格

C27 Pass 合格

C28 Pass 合格

C29 Pass 合格

C30 Pass 合格
No. C11-C20: At first cycle in fully discharged states
编号 C11-C20: 第 1 个充放电周期，完全放电状态
No. C21-C30: After 25 cycles ending in fully discharged states
编号 C21-C30: 第 25 个充放电周期，完全放电状态
Notes 注释: Atmospheric pressure 大气压强:1.013×105Pa, Ambient temperature 环境温度: 23.4 °C
There is no disassembly and no fire during the test and within seven days after the test.
电芯在测试中和测试后 7 天内未解体，未起火。

Report No. 报告编号: NCT24025466B1-1 Page 18 of 22 第 18 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Ⅶ、Conclusion 结论
No. Test item Sample number Test reference Conclusion
编号 测试项目 样品数量 测试参考 结论
UN Manual of Test and Criteria, part
Altitude simulation Ⅲ, subsection 38.3.4.1 Pass
1
高度模拟 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.1 节
UN Manual of Test and Criteria, part
Thermal test Ⅲ, subsection 38.3.4.2 Pass
2
温度试验 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.2 节
UN Manual of Test and Criteria, part
Vibration Ⅲ, subsection 38.3.4.3 Pass
3 B01#~B08#
振动 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.3 节
UN Manual of Test and Criteria, part
Shock Ⅲ, subsection 38.3.4.4 Pass
4
冲击 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.4 节
UN Manual of Test and Criteria, part
External short circuit Ⅲ, subsection 38.3.4.5 Pass
5
外部短路 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.5 节
UN Manual of Test and Criteria, part
Impact/Crush Ⅲ, subsection 38.3.4.6 Pass
6 C01#~C10#
撞击/挤压 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.6 节
UN Manual of Test and Criteria, part
Overcharge Ⅲ, subsection 38.3.4.7 Pass
7 B09#~B16#
过度充电 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.7 节
UN Manual of Test and Criteria, part
Forced discharge Ⅲ, subsection 38.3.4.8 Pass
8 C11#~C30#
强制放电 UN 试 验 和 标 准 手 册,第 Ⅲ 部 分,第 合格
38.3.4.8 节

The submitted samples were complied with the stated requirements of UN manual of test and criteria,
part Ⅲ, subsection 38.3, the test result is qualified.

经检测，提交的测试样品均符合 UN38.3 的要求，测试结论为合格。

Report No. 报告编号: NCT24025466B1-1 Page 19 of 22 第 19 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Ⅷ、Photo of The Sample 样品图片

Model 型号: BRL1010B-15A

Photo 1 Front 正面

Photo 2 Rear 反面

Report No. 报告编号: NCT24025466B1-1 Page 20 of 22 第 20 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

Photo 3 Internal Cell 内部电芯

Photo 4 Internal Cell 内部电芯

Report No. 报告编号: NCT24025466B1-1 Page 21 of 22 第 21 页共 22 页

Hotline: 400-8868-419 Tel: 86-755-23218380 http://www.ncttesting.cn
 Lithium Battery UN38.3 Test Report

注意事项

Important Notice

1. The test report is invalid without the official stamp of NCT.

本报告书无 NCT 盖章无效.
2. Nobody is allowed to photocopy or partly photocopy this test report without written permission
of NCT.
未经 NCT 书面同意，不得部分地复制本报告书。
3. The test report is invalid without the signatures of Ratifier, Reviewer and Testing engineer.
本报告书无批准人、审核人、及主检人签名无效。
4. The report is invalid when anything of following happens – illegal transfer, reproduce,
embezzlement, imposture, modification or tampering in any media form.
私自转让、复制、盗用、冒用、涂改、或以任何媒体形式篡改的报告书无效。
5. Objections to the test report must be submitted to NCT within 15 days.
对报告书若有异议，应于收到报告之日起 15 天内向本公司提出。
6. The test report is valid for the tested samples only.
本报告仅对测试样品有效。
7. The Chinese contents in this report are only for reference.
本报告中的中文内容仅供参考。

******End of Report 报告结束******

Shenzhen NCT Testing Technology Co., Ltd. 深圳诺测检测技术有限公司

B2A101/B2A201/B2A202, Fuqiao 6th Area, Xintian, Fuhai Subdistrict, Bao'an District, Shenzhen,
Guangdong, China
广东省深圳市宝安区福海街道新田社区富桥六区 B2A101, B2A201, B2A202
Search Number 查询编号 NCT24025466B1-1
Search System 查询系统: http://www.ncttesting.cn Page 22 of 22 第 22 页共 22 页
报告模板编号: TRF.UN38.3 Rev.7+Amend.1-V4 模板日期：2023-11-13