Dismantle Transmission: tm6018 - Tractors 5415, 5415 Narrow, 5415H, 5615, 5715, and 5715HC Dismantle Transmission
Uploaded by
ScribdTranslationsDismantle Transmission: tm6018 - Tractors 5415, 5415 Narrow, 5415H, 5615, 5715, and 5715HC Dismantle Transmission
Uploaded by
ScribdTranslationsPage 1 of 4
tm6018 - Tractors 5415, 5415 Narrow, 5415H, 5615, 5715, and 5715HC
Dismantle Transmission
Dismantle Transmission
LV7342-UN: Disassemble Transmission
1. Separate the clutch housing from the transmission. (See 'Separate the Clutch Housing from the Transmission' in this)
group).
2. Lift and place a support under the rear axles.
3. Remove the rear wheels and the fenders.
4. Remove the control levers from the oscillating shaft.
5. Remove the control console from the right side. (See "Remove and Install the Control Console from the Right Side and
Panel in Section 90, Group 06.
6. Remove the control lever from the remote cylinder valve box and the cable assembly, if applicable.
equipped. (See procedure in Section 70, Group 15).
NOTE:
Close all openings using covers and plugs.
7. Remove the brake line from the right side.
Page 2 of 4
.
LV2452-UN: View Left Side
LEEND:
Changer Box
Screws (are used)
C - Nut (they are used)
Remove the front traction control lever and its connections. (See 'Check and Repair Lever and
Mechanical Front Traction Connections "in this section, Group 35).
9. Remove the lever for the output take-off and its connections. Review
(See and Repair Lever and TD Connections ”
procedure in Group 20).
10. Remove the control console from the left side. (See 'Remove and Install the Control Console from the Left Side and
the Panel" in Section 90, Group 06).
11. Remove the gear shift levers and the range shift lever. (See the procedure for this)
group).
12. Remove the eight screws () and the nuts (C) to disassemble the cover and the gearboxes (). Repair if necessary.
necessary. (See Disassembly and Inspection of Transmission in Section 50, Group 15).
13.
LV2451-UN: Range Shift Lever Assembly
READ:
Screws (2 are used)
security ring
C - range change fork and C
D - range change fork () and idle
E - Low gear shift axis and Range
Range change axis and C
G - Shirt
- align (use 2)
Page 3 of 4
I - Spring (2 are used)
you
Screw
L - Screw
M - Plate
N - Bolt
Alín
Remove the pieces ( -).
14. Remove the screws () and the safety washers (). Slide the shift axes ( and E) forward in the
transmission box to obtain the necessary space to remove the shift forks.
15. Dismantle the shift fork (C).
16. Disassemble the gear fork (D).
17. Install the bushing () and the screw () to assist you in disassembly.
1.
LV531-UN: Transmission case
Remove the hydraulic oil filter assembly. (See 'Remove and Install the Hydraulic Oil Filter Assembly') ”
in Section 70, Group 05.
19. Remove the side cover or the idle assembly, if so equipped. (See "Remove and Install the
Slow Transmission (Creeper) in this section, Group 40.
20. Remove the lower cover or the gear box of the front traction control TDM, if equipped.
Remove and Install the Mechanical Front Drive Connection Gearbox in this section, Group
35).
21. Place a support bench under the assembly of the traction bar.
22. Place a hoist and chains on the transmission box.
M T T
Before plowing the rear transmission of different types through this operation.
This is the disconnection of the inner art of transmitting and tracing this deactivation.
it will not leave Eden of the ass in the frogs I am going to speak about transmission of differences.
NOTE:
The drive shaft of the differential and the gear assembly will remain with the differential.
during the transmission withdrawal.
23. Remove the ten screws. Remove the transmission.
24. Make the necessary repairs. (See procedures in this group).
Page 4 of 4
G,P03972,261 -63-20000530