Instructions for use Washer disinfector

INSTRUCTIONS
FOR USE

Washer disinfector
Getinge 8666/8668
Mfg. no. SEV0320078-
5011450-00

9908

1
Washer disinfector Instructions for use

Contents
Safety regulations ______________________________ 3
Important ___________________________________ 3
Product liability ______________________________ 3
Symbols on the machine _______________________ 4
Attention symbols ____________________________ 4

General _______________________________________ 5
Programmer _________________________________ 6
Door function _______________________________ 6
Manually-operated door ____________________ 7
Automatically-operated door _________________ 7
Dosing system _______________________________ 7

Operating instructions ___________________________ 8

Fault indications ________________________________ 9

A red lamp lights up __________________________ 9
Handling alarm _______________________________ 9
Fault codes _________________________________ 10
Acknowledgement of fault code _________________ 11

Inspection ____________________________________ 12
Daily ______________________________________ 12
If necessary _________________________________ 12
Washing chamber _________________________ 12
The outside ______________________________ 12

Printing out a program __________________________ 13

Hospital A0 600 (90 °C - 1 min) ___________________ 14

LAB _________________________________________ 14

Hospital USA A0 600 (90 °C - 1 min) _______________ 15

Detergent ____________________________________ 16
Getinge detergent for mechanical washing of: _______ 16
Acidic detergents and neutralizing agents _________ 16
Lubricants and rinse aids _______________________ 16
Flusher detergents ____________________________ 16

9908

2
Instructions for use Washer disinfector

Safety regulations
This machine is designed with a number of built-in safety devices. To avoid
injury, it is very important that these safety devices are not bypassed and thus
disabled.

The equipment must be used in accordance with the safety

instructions below.
If in doubt, contact a representative of the reseller without delay.

Important
• Read the instructions thoroughly before use
• The equipment must only be used by personnel who know about it and are
trained to use it. Personnel must also receive regular training on this
equipment.
• take care when handling the chemical agent used in the machine. Read the
details on the container or contact the manufacturer:
- if agent comes into contact with the operator’s eyes or skin or if the
vapours are breathed in, etc.
- about storing the agent and disposing of empty containers.
• Take care, because the machine uses hot water and possibly steam.
• Installation and service work must be done by personnel trained for this
machine.
• Never bypass the door switch of the machine.
• Leakage in the system, due to a worn door seal for example, must be repaired
without delay.
• The electric power is cut off before the machine cabinet is opened. (The
machine cabinet contains electrical components).
• Make sure that there is always detergent in the bottles. This is important both
for the operation of the machine and for keeping the washing chamber free
from discolorations.
• The machine must be kept clean if it is to work properly.
• Do not wash down or hose down the machine with water.

Product liability
• Modifications to the equipment made without the approval of the
manufacturer, or incorrect use, invalidate the manufacturer’s product liability.

9908

3
Washer disinfector Instructions for use

Symbols on the machine

Warning, see instructions for use.
Warning, hot surface.

Attention symbols
Some of the warnings, instructions and advice in this manual are so important
that we used the following special symbols to draw attention to them. The
symbols used are as follows:

This symbol indicates a warning in the text of the manual. The

nature of what the warning relates to is such that it may result in
more or less severe injury and in certain cases mortal danger.

It also highlights warnings to avoid damage to equipment.

9908

4
Instructions for use Washer disinfector

General
The machine is a fully-automatic washer disinfector for cleaning and disinfecting
goods in hospitals, laboratories and the pharmaceutical industry.
The machine has two washing vanes and two dockings and can be equipped
with several different accessories for different cleaning requirements. These
accessories are presented in a special accessories catalogue.
There are several possible ways of installing and equipping the machine
depending on its field of application:
• Heating by electricity or steam.
• Connection of distilled or de-ionised water.
• Electrically-heated booster tank for the water for the final rinse.
• Single or double door.
• Extra dosing pumps which allow chemical disinfection of heat-sensitive goods.
• Infeeder/outfeeder
• Automatic program selection (basket indication)
• Audible signal on process complete, fault code, etc.
The Decomat 8666 has been tested and approved in accordance with SPRI and
BGA recommendations.

V1454

9908

5
Washer disinfector Instructions for use

Programmer
The machine has an electronic controller which can hold up to 10-15 programs.
Six of these programs can be chosen with the program selection buttons. To
choose other programs, press S. The display now shows SELECT CYCLE.
Press S again and choose a program with H and J.
The machine comes with a number of standard programs in the programmer (see
the separate program sheet). Contact the manufacturer for customised programs.

Programming may only be done by authorised personne

Door function
The Decomat A 8666 can be fitted with a single door or double doors. All doors
are of the vertical sliding type.
The doors can be motorised for automatic opening and closing. The doors have
efficient anti-crush protection.
Machines with double doors have a system of interlocks to ensure that only one
door can be opened at a time. This means that the clean-side door must be closed
and locked by pressing the W button before the soiled-side door can be
opened.
When V is pressed, the door is locked and a yellow lamp flashes (process
running) for about 10 seconds. If V is pressed again during this “cancel time”,
the soiled-side door is unlocked and the door can be opened manually or
alternatively it opens automatically.
In standby mode the door can be opened and closed by pressing U 5 sec.

Clean side Soiled side

V398

9908

6
Instructions for use Washer disinfector

Manually-operated door
When the door is closed manually and V is pressed, the door is clocked
automatically, the yellow lamp flashes and the program starts.
When the program is complete, a green lamp lights up on both sides (if there are
double doors) and the clean-side door is unlocked. When the door has been
opened manually, the green lamp goes out. With double doors, the clean-side
door must be closed and locked by pressing the W button before the soiled-
side door can be unlocked.

Automatically-operated door
When V is pressed, the door is locked, the yellow lamp flashes and the program starts.
When the program is complete, a green lamp lights up on both sides (if there are
double doors) and the clean-side door opens automatically. When the door is
fully open the green lamp goes out on both sides. With double doors, the clean-
side door must be closed and locked by pressing the W button before the
soiled-side door opens automatically.

Dosing system
In standard form, the machine has two different dosing systems. One is for
alkaline detergent and one is for rinse-aid or acid detergent. The dosing amount
can be set individually for each program.
Dosing pumps

Empty
container
alarm

Holder for
detergent/
rinse-aid

V1447

The machine cannot be started until detergent has been dispensed. If the
detergent holder is empty "ADD DETERGENT" appears on the display.
A third and a fourth dosing system for heat-sensitive goods or instrument milk,
for example, can be installed.

9908

7
Washer disinfector Instructions for use

Operating instructions

Before starting: Chosen

program
Program number P01 OP-SHORT-D While running: Program
47.0°C phase (eg “Rinsing”)

Programming buttons
(see “Service instructions”)

Program selection buttons

Yellow: Process running

Resets alarm
Green: Process complete
Red: Fault code Start wash program

V1363

• Load the goods to be washed on to the trolley and run the trolley into the machine.
Example showing how to load the trolley are shown on the goods positioning plate.
• Make sure that the washer arms can rotate freely without touching the goods.
Close the door.
• Choose a program in one of the following ways:
- by pressing one of the program selection buttons 1 - 6
- by pressing S. The display now shows SELECT CYCLE. Press S again
and choose a program with H and J.
You can see the machine programs on the separate program sheet.
• Press V. While the program is running, a yellow lamp at M is lit and the
program phase (eg "Rinse") is shown on the display. Press S to see the
current temperature and press S again for the remaining time.
• When the program is complete, a green lamp lights up at N and the door is
unlocked (with double doors, the clean-side door).

If the goods have not cooled down after a process, be sure to

handle them with care, to avoid burns.
• Empty the machine (and if the machine has double doors, close the clean-side door).
- For a machine with automatic door: Press W to close and lock the clean-
side door.
- For a machine with manual door: First close the door, then press W to lock
the clean-side door.
• If the same program is to be used again, there is no need to select the program
again. Simply press Vonce.
• When V is pressed, a yellow lamp flashes for 10 seconds. During this time,
the program can be aborted by pressing Vigen.

Note: The display switches to rest mode after 30 minutes and returns
9908 automatically when a program is started or selected.

8
Instructions for use Washer disinfector

Fault indications

Fill detergent 1

Fault message or fault code

Red lamp: Fault code

A red lamp lights up V1363

If the red lamp at O lights up, the process has stopped because of a process
fault. Call service personnel.

Handling alarm

Add detergent 1
Operation message appear on the display in plain text. The machine cannot be
started until the fault has been put right.

Add detergent 1 Empty container alarm 3. If detergent 3 is finished, an

operation code is generated. The alarm is reset automatically
when detergent is added.
Add detergent 2 Empty container alarm 3. If detergent 3 is finished, an
operation code is generated. The alarm is reset automatically
when detergent is added.
Add detergent 3 Empty container alarm 3. If detergent 3 is finished, an
operation code is generated. The alarm is reset automatically
(Option) when detergent is added.
Add detergent 4 Empty container alarm 3. If detergent 3 is finished, an
operation code is generated. The alarm is reset automatically
(Option) when detergent is added.

Note: 7When the operation message “Add detergent 1-4” appears,

9908 there is always enough detergent for one run.

9
Washer disinfector Instructions for use

Fault codes

F01

Fault codes indicate that a serious fault has occurred in the washing process.
The fault must be put right by an authorised service technician.

The following fault codes may occur:

Fault code Description of fault

F00 Power failure

F01 Motor cutout has tripped.

F02 Water filling takes more than 10 minutes.

F03 Draining takes longer than 5 minutes or there is water remaining in

the washing chamber at the end of the draining phase.

F04 Water leakage in the drying unit.

F05 Soiled-side door does not lock within 10 seconds of program start
or the door is opened while a program is running.

F06 Soiled-side door does not unlock within 10 seconds of the end of
aprogram.

F07 Soiled-side door does not close within 20 seconds of program start
or the door is opened while a program is running.

F08 Soiled-side door does not open within 20 seconds of the end of a
program.

F09 Soiled-side door does not lock within 10 seconds of program start
or the door is opened while a program is running.

F10 Soiled-side door does not unlock within 10 seconds of the end of a
program.

F11 Soiled-side door does not close within 20 seconds of program start
or the door is opened while a program is running.

F12 Soiled-side door does not open within 20 seconds of the end of a
program.

F15 Not enough detergent 1 dosed.

F16 Not enough detergent 2 dosed.

F19 Not enough detergent 3 dosed.

F20 Not enough detergent 4 dosed.

F21 Slow filling of booster tank.

9908

10
Instructions for use Washer disinfector

Fault code Description of fault

F23 High conductivity.

F24 Low pressure in drying unit.

F25 High pressure in drying unit.

F26 Low pressure from circulation pump.

F27 High pressure from circulation pump.

F28 Low temperature in drying unit.

F29 Incorrect temperature in booster tank.

F30 Incorrect temperature in washing chamber.

F31 Incorrect temperature in washing chamber.

F32 Incorrect temperature in drying unit.

F33 Incorrect temperature in washing chamber.

F34 Incorrect temperature in washing chamber.

F35 Incorrect temperature in booster tank.

Acknowledgement of fault code

Acknowledge the fault code by:
• pressing U. The alarm signal stops. The machine is still locked but the
current process has been aborted.
• correct the fault or open the door to gain access to the goods. Pressing V
drains liquid from machine and the soiled side door goes down.

NOTE:
The goods in the machine are not clean. Start a new process.

9908

11
Washer disinfector Instructions for use

Inspection
Spray wing

Coarse strainer

V773

Daily
• Check that there are no objects in the bottom of the washing chamber.
• Check that the washing arms can rotate freely. Check that the holes in the
washing arms are not blocked.
If the arms need cleaning, remove them by unscrewing the central nut. Check
that the arms can rotate freely when re-installed.
• Remove and clean the strainer in the bottom of the washing chamber.
• Open the detergent door and check that there is detergent/rinse-aid in the
containers.
• Check that the trolley docks properly with the water connections.

If necessary
Washing chamber
Keep the washing chamber free of limescale deposits. Remove any remaining
deposits as follows:
• Open the door and does 200 ml Lime-Away descaler (sold by Henkel) or
NEODISHER BU (sold by Dr. Weigert) into the wash chamber.
• Close the door and run the descaling program.

NOTE: Do not have any goods in the machine with this program. It is
only for descaling the machine and insert.

The outside
The front and side walls can be cleaned and disinfected with an alcohol-based
cleaning agent, medical spirit or an ordinary cleaner. the control panel is cleaned
in the same way.
Remove stains with an ordinary stainless steel cleaner.

9908

12
Instructions for use Washer disinfector

Printing out a program

An example of a program printout is shown below. In the example the program
P02 OP-D, programmed on program selection button 2 is used.

PROGRAM:P2 OP-D PH20-DRAINING 40 s

DATE:13/04/2004 00:14:18 61.5
PROCESS START:13:44:46
MACHINE NAME:S-8666 PH330-RINSE 1
MACHINE NO:1 00:15:29 61.5
CYCLE COUNTER:1
PH20-DRAINING 40 s
00:17:39 55.1
PARAMETER
WASH DOS TEMP 35.0C PH360-RINSE 2
WASH DOS 1 00:01:00 00:18:46 55.5
WASH TEMP. 60.0C
WASH TIME 00:03:00 PH20-DRAINING 40 s
FINAL R DOS TEMP 80.0C 00:20:55 53.2
FINAL R DOS 3 00:00:21
PH440-FINAL RINSE
DISINF TIME 00:01:00
00:22:03 53.5
DISINF TEMP 90.0C
00:27:53 80.1
DRYING TEMP9 0.0C DOS.START
DRYING TIME 00:18:00
00:28:15 81.5
SIGNALS DOS.STOP
A107 TEMP INDEP. CHAMB
00:30:26 90.0
PROGTIME A107
PH450-DISINFECTION
00:30:27 90.1
PH1-START
00:31:26 92.3
00:00:00 30.8
PH20-DRAINING 40 s
PH2-DRAINING 10 s 00:31:28 92.3
00:00:00 31.2
PH900-DRYING
PH220-PRE RINSE CW 00:32:36 91.7
00:00:10 31.0 00:51:27 80.8

PH1000-ENDING
PH20-DRAINING 40 s
00:52:43 81.1
00:02:42 16.2
SIGNATURE: .........
PH25-WASHING
00:03:51 18.1
00:05:52 35.2
DOS START

00:06:53 39.9
DOS.STOP

00:11:17 60.0
00:12:17 608
00:13:17 61.9
00:14:17 61.5

9908

13
Washer disinfector Instructions for use

Program groups are described below. See the attached program sheet for more information about
programs for this machine

Hospital A0 600 (90 °C - 1 min)

This program sheet applies to 5011294-13, -14.
Programs Program selection button/ Type of goods
Program number
INST./POLY 1 Instruments, circulation goods
INST./POLY (ENZ) 2 Instruments, circulation goods
AN/MIS 3 Anaesthesia tubing, mic-instruments
- 4 -
- 5 -
- 6 -
DRYING P10 * Drying.
DESCALING P11 * Descaling of chamber, inserts washer arms and washer vanes.
Dose 200 ml Lime-Away descaler (sold by Henkel) or NEO-
DISHER BU (sold by Dr. Weigert) into the wash chamber.
NOTE: Do not have any goods in the machine with this
program. It is only for descaling the machine.
* For choosing this program, see page 8.

LAB
This program sheet applies to 5011294-18.
Programs Program selection button/ Type of goods
Program number
LAB-SHORT-D 1 Slightly dirty labgoods
LAB-D 2 Labgoods
TEST TUBES-D 3 Test tubes
LONG-LAB-D 4 Very dirty labgoods
PIPETTES 5 Pipettes
- 6 -
LAB-SHORT P7 * Slightly dirty labgoods. Without drying.
LAB P8 * Labgoods. Without drying.
TEST TUBES P9 * Test tubes. Without drying.
DRYING P10 * Drying.
DESCALING P11 * Descaling of chamber, inserts washer arms and washer vanes.
Dose 200 ml Lime-Away descaler (sold by Henkel) or NEO-
DISHER BU (sold by Dr. Weigert) into the wash chamber.
NOTE: Do not have any goods in the machine with this
program. It is only for descaling the machine.
* For choosing this program, see page 8.

9908

14
Instructions for use Washer disinfector

Hospital USA A0 600 (90 °C - 1 min)

This program sheet applies to 5011294-17.
Programs Program selection button/ Type of goods
Program number
INSTRM-LONG 1 Very dirty instruments
INSTRM-SHORT 2 Circulation goods, slightly dirty instruments. Containers.
UTENSILS 3 Circulation goods
ORTHOPEDIC 4 Orthopedic instruments
MIS INSTRM 5 Mis instruments
ANESTESIA 6 Anaesthesia tubing
CASSETTES P7 * Cassettes
LAB-SHORT-D P8 * Slightly dirty labgoods
LAB-D P9 * Labgoods
TEST TUBES-D P10 * Test tubes
DESCALING P11 * Descaling of chamber, inserts washer arms and washer
vanes. Dose 200 ml Lime-Away descaler (sold by Henkel) or
NEODISHER BU (sold by Dr. Weigert) into the wash
chamber. NOTE: Do not have any goods in the machine with
this program. It is only for descaling the machine.
* For choosing this program, see page 8.

NOTE: To choose the recommended agent, see under Detergent in the user instructions.

9908

15
Washer disinfector Instructions for use

Detergent
The machine has been tested with Getinge detergent. We recommend that you
use Getinge detgerent or detergent from a reputable manufacturer.

Getinge detergent for mechanical washing of:

A - Surgical instruments B - MIS-instruments
C - Anesthesia equipment D - OP-shoes
E - Containers F - Baby-bottles G - Lab glassware
Products Alkalinity Surfactants Phosphates Enzymes Suitable for optics Goods to
and anodized Alu. be washed
Getinge Wash Normal Amines + - + + A, B, C, D, E
Getinge Wash Extra Alkaline salts - + - (+) A, C, D, (E), F
Getinge Wash Intensive Caustic soda + - - - A, C, D, F
Getinge Wash Enzyme - + - + + A, B, C, D, E
Getinge Wash LAB Caustic soda - - - - G

Acidic detergents and neutralizing agents

Products Acids Effects Prewash for Dosage
lab glassware
Getinge Neutralization P Phosphoric Neutralization of alkaline residues, Removal of First rinse after the alkaline
acid, citric removal of mineral residues, e.g. mineral residues wash for neutralization or
acid rust and lime prewash
Getinge Neutralization Citric acids Neutralization of alkaline residues First rinse after the
alkaline wash

Lubricants and rinse aids

Products Ingredients Effects Dosage
Getinge Instrumentmilk Paraffinum perliquidum Lubrication of instruments Final rinse
emulsifying agents
Getinge Rinse Surfactants Reduction of surface tension Final rinse
of water, improved drying

Flusher detergents
Products Alkali Dispersion agents Complexing agents Surfactants
GD Wash + - ++ +
GD Flush - ++ + -

Getinge detergents can be ordered from Getinge resellers.

9908

16
Washer disinfector Instructions for use

This product is manufactured by:

GETINGE DISINFECTION AB, Ljungadalsgatan 11, Box 1505, 351 15 Växjö, Sweden

9908

18