AkzoNobel
Aerospace Coatings
Aerodur Clearcoat UVR
Technical Data Sheet
Product Group Polyurethane Topcoats
Characteristics Aerodur Clearcoat UVR is a universal 3-component, UV Resistant, high
Product gloss polyurethane topcoat for application on exterior polyurethane
Information decoration schemes.
- Extended durability of conventional polyurethane systems.
- Long lasting “wet look” appearance.
- No dirt retention.
- Easy to clean.
- Resistant to aircraft hydraulic fluids and chemicals.
- Base, hardener and Thinner 98064 comply to the German legislation
o
VBF: A2 (flashpoint >21 C)
Components Hardener S 66/22 R
Curing Solution Thinner C 25/90 S (normal conditions, flashpoint <21ºC)
Thinner / Thinner 98064 (warm conditions, flashpoint >21ºC)
Activator Thinner 96184 (warm conditions, flashpoint <21°C)
Specifications Airbus AIMS 04.04.022
Qualified AIMS 04.04.023
Product List
Embraer MEP 10-058
For most recent up-date or missing specifications please check the qualified
product list (QPL) on www.akzonobel.com/aerospace.
Surface Conditions - Observe the recoatability limits of the relevant finish.
Cleaning - Remove oil, grease and other contaminants prior to application of the
finish.
®
- Recondition aged primers or topcoats with e.g. Scotch-Brite type A
very fine till a uniform matt surface.
- Remove dust with e.g. rack rags prior to application of the finish.
Page 1 of 5
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
Aerodur Clearcoat UVR
Instruction for Use
Mixing Ratio 100 parts Aerodur Clearcoat UVR
(volume) 100 parts Hardener S 66/22 R
Reduce to spraying viscosity with:
50 – 75 parts Thinner C 25/90S, Thinner 98064 or Thinner 96184.
- Allow products to acclimatize to room temperature before use
- Stir or shake Aerodur Clearcoat UVR thoroughly before adding
hardener.
- Add Hardener S 66/22 R and stir the catalyzed mixture thoroughly.
- Add thinner and stir again till a homogeneous mixture.
Induction Time 15 – 30 minutes after mixing.
Initial Spraying 36 – 42 seconds ISO-Cup 3
Viscosity 27 – 29 seconds Gardner Signature Zahn-Cup #1.
(25ºC/77ºF)
Note Viscosity measurements are provided as guidelines only and are not to
be used as quality control parameters. Certified information is provided
by certification documentation available on request.
Pot life 8 hours.
(25ºC/77ºF)
Dry Film 35 – 45 micron (m)
Thickness 1.4 – 1.8 mils
(DFT)
Application
Recommendations
Conditions Temperature: 15 – 35°C
59 – 95°F
Relative Humidity: 35 – 75%
Page 2 of 5
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
Aerodur Clearcoat UVR
Equipment Air 1.4 mm nozzle orifice
HVLP 1.4 mm nozzle orifice
Air Electrostatic 1.2 mm nozzle orifice
Airless Electrostatic 6.11 – 6.13, (.011 - .013 inch) angle 60º
Number of Coats Apply an even wet closed coat, followed after 30 minutes flash-off time by
one cross-coat
Cleaning of Solvent Cleaning C 28/15 or Solvent Cleaning 98068.
Equipment
Note The quality of the application of all coatings will be influenced by the
spray equipment chosen and the temperature, humidity, and air flow of
the paint application area. When applying the product for the first time, it
is recommended that test panels be prepared in order to identify the best
equipment settings to be used in optimizing the performance and
appearance of the coating.
Physical Properties
Drying Times Dust free 3 – 4 hours
(21ºC / 77ºF) Dry to tape 10 – 12 hours
Recoatable minimum 6 hours
Recoatable maximum 24 hours,
If a drying time of 24 hours is exceeded,
®
condition surface with e.g. Scotch-Brite
type A very fine.
18 m per liter base material at 35 m dry film thickness
2
Theoretical
2
Coverage 722 ft per US gallon base material at 1.4 mil dry film thickness
2
Dry Film Weight 1,1 g/m /µm
2
0,0057 lbs/ft /mil
Page 3 of 5
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
Aerodur Clearcoat UVR
Gloss (60º) Minimum 93 GU
Color Clear
Flash-point Aerodur Clearcoat UVR >21ºC / 70ºF
Hardener S 66/22 R >21ºC / 70ºF
Thinner C 25/90 S <21ºC / 70ºF
Thinner 98064 >21ºC / 70ºF
Thinner 96184 <21ºC / 70ºF
Storage Store the product dry and at a temperature between 5 and 25ºC / 41 and
77ºF. Stored in the original unopened containers.
Shelf life Aerodur Clearcoat UVR 24 months
5 - 38°C Hardener S 66/22 R 24 months
(40 - 100°F) Thinner C 25/90 S 36 months
Thinner 98064 36 months
Thinner 96184 36 months
Safety Precautions Comply with all local safety, disposal and transportation regulations.
Check the Material Safety Data Sheet (MSDS) and label of the individual
products carefully before using the products. The MSDS’s are available
on request.
Page 4 of 5
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
Aerodur Clearcoat UVR
Issue date: September 2015 (supersedes March 2015) - FOR PROFESSIONAL USE ONLY
IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person
using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of
the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules
and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we give or any statement made about the product by
us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors
affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of
the product or for any loss or damage arising out of the use of the product. All products supplied and technical advice given is subject to our standard terms and conditions of
sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of
experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.
Brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel.
Scotch-Brite® is a registered trademark of the 3M Company.
Page 5 of 5
AkzoNobel Aerospace Coatings
1 East Water Street, Waukegan, IL 60085, USA - Phone (847) 623 4200, Fax (847) 625 3200
Rijksstraatweg 31, 2171 AJ Sassenheim, The Netherlands - Phone (31) 71 308 2905, Fax (31) 71 308 2056
Internet: www.akzonobel.com/aerospace
