1 2 3 4 5 6 7

I ! egg
U 4 W
U.V. RESISTANT (BLACK) NYLON CABLE TIE
(TYPICAL) STAGGER CABLE TIES EVERY
12'-0" FOR HORIZONTAL RUNS. CABLE TIES
3/C-500 KCMIL 15KV SHALL BE THOMAS AND BETTS DELTEC
TAG ( TYPICAL ) TYPE OR APPROVED EQUAL.

CABLE TRAY
1 5/8" X 1 5/8"

HANNEL-
_ 3/C-500 KCMIL l.A.C. I I / " l I I I
CABLE

MULTI-CABLE TRANSIT FRAME I || Ill b eè

SEE DETAIL
|| / || | I L 6 ± -
FINISHED FLOOR

r -
DANGER
CABLE TRAY
.LL_ LL___ dl BID SET
SIDE RAIL
o o o o o o HIGH VOLTAGE

E 4" (TYP)

18" TYPICAL EXISTING OR

PROVIDE HEAVY-DUTY DOUBLE TRUSS HEAD BOLT WITH FLAT TRUSS HEAD BOLT WITH HEX FUTURE 15 KV
EYE SUPPORT CLOSED MESH WASHER & ELASTIC LOCK NUT NUT & CAPTIVE LOCK WASHER CABLES
-- 1-500 KCMIL BARE ALUMINUM
GROUND CABLE LUG TOCABLE CABLES MUST BE IDENTIFIED EXISTING OR
TRAY FLEXIBLE ALUMINUM BONDING AT LEAST EVERY 40'-0 BY NEW CABLE TRAY
JUMPER MINIMUM 600A. CAPACITY - FEEDER NO. WITH PLASTIC
NOTE: NAMETAG ATTACHED WITH
TRUSS TY-WRAP OR SNAP-ON TYPE
CABLE TRAY MOUNT SIGN ON BOTH SIDES OF CABLE TRAY AT WRAPS.
INTERVALS NOT TO EXCEED 20'-0" ON CENTER, CLEAN
SIDE OF TRAY TO ENSURE PROPER ADHESION BEFORE
APPLYING SIGN AS RECOMMENDED BY CABLE TRAY
MANUFACTURER

CABLE TRAY EXPANSION FITTING &

TYPICAL CABLE TRHOUGH FLOOR DETAIL GROUND CONNECTION DETAIL CABLE TRAY WARNING SIGN DETAIL HORIZONTAL CABLE FASTENING DETAIL
NOSCALE NOSCALE NOSCALE NOSCALE

I
l--
O
ca
<
MECHAN CAL CONTRACTOR ROOF CURB --

<
N
< 45° ANGLE FITTING
O B-LINE #B248 SERIES
1/2" DIAMETER STEEL HANGER OR APPROVED EQUAL
O ROD. FOR CONTINUATION, SEE (TYP.)
TYPICAL HANGER ROD
C CONNECTION DETAIL. 90°CORNERANGLE
SECURE TO CABLE TRAY FITTING B-LINE #B101
RUNG PER GRIP 042 SERIES OR APPROVED Z
HOLD DOWN BOLT O
MANUFACTURER'S INSTRUCTION EQUAL (TYP.)
1/2" STEEL HANGER ROD W/LOCK WASHER
(TYP 2)

PROVIDE HEAVY DUTY DOUBLE U.V. RESISTANT (BLACK) NYLON CABLE TIE CABLE TRAY 1 %"X 1 %" 12 GA STRUT
EYE SUPPORT CLOSED MESH AT (TYPICAL) LASH CABLE TO TRAY EVERY 12'-0" SIDE RAIL CHANNEL LAG BOLTED
- TOP OF ALL VERTICAL RISES FOR HORIZONTAL RUNS. CABLE TIES SHALL TO ROOF CURB <
BETHOMASAND BETTS DELTECTYPEOR 12/3R WITHOUT
U.V RESISTANT (BLACK) NYLON CABLE APPROVED EQUAL KNOCKOUTS) MOUNTED
F- TIE (TYPICAL) CABLE TIES SHALL BE HOLD DOWN CLAMP
PLAN ON STRUT CHANNEL
THOMAS & BETTS DELTEC TYPE OR - CABLE TRAY NUT & LOCK WASHER <
z APPROVED EQUAL EXHAUST FAN BY 6"- 1 5/8" X 1 5/8" 12
1 5/8" SQ. WASHER MECHANICAL MAX. GAUGE STRUT
INTERLOCKED ARMORE
--CLAMP CABLES AT EACH RUNG 18" 1 5/8" X 1 5/8" CABLE CONTRACTOR VERIFY IN CHANNEL (TYPICAL) F--
Z
MINIMUM STEEL e n i..--- FIELD SAFETY SWITCH
,- O.C. ON ALL VERTICAL RISES I
STRUT CHANNEL
B
-APPROX.
3'-6"
ATTACH SUPPORT
TO CURB BELOW -- 6#12 & 1#12 GRD.-3/4"C.
EXHAUST FAN -120V.-15A. G.F.I. W.P.
SHROUD. SEAL DUPLEX RECEPTACLE
1 5/8" X 1 5/8" MINIMUM AROUND LAG BOLTS "LB" TYPE CONDUIT BODY
STEEL STRUT CHANNEL SPRING NUT IN CURB.
SEECABLETRAYAND HANGER ROD
CONNECTION TO STRUT CHANNEL "T" TYPE
DETAIL CONDUIT BODY
-8#12 & 1#12 GRD.-3/4"C.
z l-
GENERAL NOTES:
1. FOR INDOOR USE, HANGER RODS SHALL BE SELF COLORED OIL FINISHED. ROOF
GENERAL NOTES: ALL OTHER ASSOCIATED SUPPORT ACCESSORIES SHALL BE THE
1. HANGER RODS SHALL BE SELF COLORED OIL FINISHED INDOORS AND MANUFACTURERS STANDARD FINISHES.
HOT-DIP GALVANIZED FOR OUTDOOR USE. 2. FOR OUTDOOR USE, ALL BRACKETS, CLAMPS, RODS, FILLINGS AND OTHER LAG BOLT STRUT CHANNEL O
2. MAXIMUM CABLE TRAY SUPPORT SPACING SHALL BE 10'-0" (TYPICAL) SUPPORT ACCESSORIES (EXCEPT CABLE TRAY) SHALL BE GALVANIZED OR TO CURB (TYPICAL) æ
ZINC PLATED. ROOF CURB JUNCTION BOX
(BY ARCH. TRADES)
SECTION Project No.: 200-11740-10003
ó. A
Designed By: CSW
HORIZONTAL CABLE TRAY CABLETRAYANDHANGERROD ROOF MOUNTED MECHANICAL EQUIPMENT Drawn By: TAC
VERTICAL CABLE FASTENING DETAIL TRAPEZE HANGER DETAIL CONNECTION TO STRUT CHANNEL DETAIL SAFETY SWITCH MOUNTING DETAIL Checked By: DAB
NOSCALE NO SCALE NO SCALE NO SCALE

¬e
o

o
E-9510 0

Bar Measures 1 inch