PRODUCT DATA SHEET
Sikafloor® PS (ID)
EPOXY RESIN PORE SEALING AND SMOOTHING PUTTY
DESCRIPTION CHARACTERISTICS / ADVANTAGES
Sikafloor® PS (ID) is a solvent-free, thixotropic, two Sikafloor® PS (ID) is an extremely versatile product that
component, epoxy resin based putty for minor repairs offers many advantages to the user:
on concrete surfaces. ▪ Easy to apply
Suitable for use in hot and tropical climatic conditions. ▪ Suitable for dry and damp surfaces
▪ Cost effective; consumption of subsequent coatings
USES is reduced
▪ Non-shrink
Sikafloor® PS (ID) may only be used by experienced ▪ Excellent mechanical strengths
professionals. ▪ Excellent adhesion to concrete substrates
Sikafloor® PS (ID) can be used in following situations: ▪ High abrasion and impact resistance
▪ Concrete minor repairs such as honeycombing, blow ▪ High chemical resistance
holes, pin holes, etc. ▪ Solvent free
▪ General smoothing / re-profiling over large areas
▪ Suitable for feather edge
▪ Filling pinholes prior to over coating with Sikafloor®,
Sikadur® and Sikagard® product range
▪ Filling cracks and surface sealing
PRODUCT INFORMATION
Composition Epoxy resin
Packaging Part A: 15 kg
Part B: 7.5 kg
(A + B) 22.5 kg ready to mix units
Appearance / Colour Grey (Mixed A + B)
Component A: Light Grey
Component B: Dark Grey
Shelf life 24 months from date of production
Storage conditions Store in cool and dry conditions in unopened, undamaged and sealed ori-
ginal packaging at temperatures between +5 °C and +35 °C protected from
direct sunlight, heat and moisture.
Density ~1.8 kg/L (mixed resin)
Solid content 100 %
Product Data Sheet
Sikafloor® PS (ID)
September 2018, Version 01.01
020811020020000184
1/3
TECHNICAL INFORMATION
Compressive Strength 1 day ~35 N/mm2 (ASTM C 579)
7 days ~46 N/mm2 at +25 °C
14 days ~50 N/mm2
Tensile Adhesion Strength 7 days ~1.5 N/mm2
APPLICATION INFORMATION
Mixing Ratio Part A : Part B = 2 : 1 by weight
Consumption ~ 1.8 kg/m2/mm
This figure is theoretical and does not include for any additional material
required due to surface porosity, surface profile, variations in level or
wastage etc.
Layer Thickness Maximum 3 mm in one single layer.
Ambient Air Temperature +5 °C min. / +45 °C max.
Dew Point Beware of condensation!
The substrate temparture must be at least 3 °C above dew piont.
Substrate Temperature +5 °C min. / +45 °C max.
Pot Life ~45 min. (+25 °C)*
*200 g
The potlife begins when the resin and hardener are mixed. It is shorter at
high temperatures and longer at low temperatures. The greater the quant-
ity mixed, the shorter the potlife. To obtain longer workability at high tem-
peratures, the mixed adhesive may be divided into portions. Another meth-
od is to chill components A and B before mixing them (not below +5 °C).
Curing Time Sikafloor® PS (ID) can be over coated with various Sikafloor®, Sikadur® and
Sikagard® resins after 12 hours and not later than 24 hours at +30 °C. Sika-
floor® PS (ID) is fully cured after 7 days. For more details please contact
Sika Technical Department.
APPLICATION INSTRUCTIONS MIXING
SUBSTRATE QUALITY / PRE-TREATMENT Mix components (A and B) together for at least 3
minutes with a mixing paddle attached to a slow speed
▪ The substrate must be sound and of sufficient com- electric drill (maximum 400 rpm) until the material be-
pressive strength (minimum 25 N/mm2) with a min- comes smooth in consistency and an even grey colour
imum pull off strength of 1.5 N/mm2. of the mixture is obtained. Material in industrial pack-
▪ The substrate must be clean and free of all contamin- ing must be stirred well before proportioning and mix-
ants such as dirt, oil, grease, coatings and surface ing. Avoid aeration while mixing. Sikafloor® PS (ID) is
treatments, etc. supplied ready for use and only has to be thoroughly
▪ Concrete substrates must be prepared mechanically stirred.
using abrasive blast cleaning or scarifying equipment
to remove cement laitance and achieve an open tex- APPLICATION
tured surface. Sikafloor® PS (ID) has easy workability and can be ap-
▪ Weak concrete must be removed and surface de- plied by trowel, scraper, or spatula.
fects such as blow holes and voids must be fully ex-
posed. CLEANING OF EQUIPMENT
▪ All dust, loose and friable material must be com-
pletely removed from all surfaces before application Clean all equipment and tools with Sika® Colma Clean-
of the product, preferably by brush or vacuum. er immediately after use. Hardened / cured material
can only be removed by mechanical means.
Product Data Sheet
Sikafloor® PS (ID)
September 2018, Version 01.01
020811020020000184
2/3
IMPORTANT CONSIDERATIONS LEGAL NOTES
When applying to damp concrete (no standing/run- The information, and, in particular, the recommenda-
ning water) work the material well into the substrate. tions relating to the application and end-use of Sika
products, are given in good faith based on Sika's cur-
BASIS OF PRODUCT DATA rent knowledge and experience of the products when
properly stored, handled and applied under normal
All technical data stated in this Data Sheet are based conditions in accordance with Sika's recommenda-
on laboratory tests. Actual measured data may vary tions. In practice, the differences in materials, sub-
due to circumstances beyond our control. strates and actual site conditions are such that no war-
ranty in respect of merchantability or of fitness for a
LOCAL RESTRICTIONS particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either
Note that as a result of specific local regulations the from this information, or from any written recom-
declared data and recommended uses for this product mendations, or from any other advice offered. The
may vary from country to country. Consult the local user of the product must test the product’s suitability
Product Data Sheet for the exact product data and for the intended application and purpose. Sika re-
uses. serves the right to change the properties of its
products. The proprietary rights of third parties must
ECOLOGY, HEALTH AND SAFETY be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
For information and advice on the safe handling, stor- refer to the most recent issue of the local Product Data
age and disposal of chemical products, users shall refer Sheet for the product concerned, copies of which will
to the most recent Safety Data Sheet (SDS) containing be supplied on request.
physical, ecological, toxicological and other safety-re-
lated data.
PT. Sika Indonesia Head Office and
Jl. Raya Cibinong-Bekasi Km.20
Limusnunggal-Cileungsi
Bogor 16820-Indonesia
Tel. +62 21 8230025, Fax +62 21 8230026
Web: idn.sika.com
Email: sikacare@id.sika.com
SikafloorPSID-en-ID-(09-2018)-1-1.pdf
Product Data Sheet
Sikafloor® PS (ID)
September 2018, Version 01.01
020811020020000184
3/3
