PROPOSED 2 - STOREY VILLA

At JARI AL SHAIK , KINGDOM OF BAHRAIN

for:
MRS. FARAH RABEEA

2 STOREY VILLA

PROJECT NO. ARJ-24-002

AUGUST 2025 - Issued for Construction
 PROJECT ID: ARJ-24-002

DRAWING SCHEDULE LIST OF ABBREVIATIONS NOTES:

ARCHITECTURAL SYMBOLS All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
ARCHT ARCHITECT ID INTERIOR DESIGN and shall not be copied, printed or used for any
BR BEDROOM IL INVERT LEVEL other purpose than specified.
ELEVATION NUMBER (ALPHABETS)
KIT ENTRANCE INT INTERNALS/INTERIORS
SERIAL # SHEET NO. DRAWING TITLE ELEVATION PAN PANTRY IP INTERLOCKING PAVER Figured dimensions only are to be used 'For
DRWG. NO. WHERE ELEVATION APPEARS Construction' and any scaling of the drawing will be
T&B TOILET AND BATHROOM JC JANITOR CLOSET
at the Contractor's risk.
WRM WASHROOM JT JOINT
ARCHITECTURAL MECHANICAL SECTION NUMBER (ALPHABETS) LIV LIVING KG KILOGRAM Contractors are to verify all dimensions on-site and
BLDG. SECTION DIN DINING LP LOWPOINT any discrepancies shall be addressed in writing to
1 AR-000 COVER PAGE 1 M-01 GENERAL NOTES DRWG. NO. WHERE SECTION APPEARS
this office, for clarification prior to the
BAL BALCONY LVL LEVEL
DRAWING SCHEDULE, ARCHITECTURAL SYMBOLS LIST commencement of the work, otherwise the
2 AR-001 2 M-02 GROUND FLOOR AC LAYOUT AD ACCESS DOOR M METER
LIST OF ABBREVIATIONS Contractor shall be at full responsibility for any
DETAIL NUMBER (NUMERICALS) BSMT BASEMENT MR MARBLE associated cost.
3 SITE DEVELOPMENT PLAN, AREA STATEMENT, FIRST FLOOR AC LAYOUT DETAIL SECTION BDY BOUNDARY MAX MAXIMUM
AR-002 PLOT LOCATION, LOT PLAN 3 M-03
DRWG. NO. WHERE DETAIL APPEARS
BL BUILDING LINE MECH MECHANICAL All drawings concerned shall be read along with all
4 AR-100 GROUND FLOOR PLAN 4 M-04 ROOF FLOOR AC LAYOUT CAB CABINET MH MANHOLE relevant structural, electro- mechanical and all other
ELEVATION NUMBER (NUMERICALS) CLO CLOSET MIN MINIMUM
related drawings.
5 AR-101 FIRST FLOOR PLAN INTRERNAL ELEVATION CONTR CONTRACTOR MM MILLIMETER
DRWG. NO. WHERE DETAIL APPEARS Any claims for variations or additional shall be
DIA DIAMETER MO MASONRY OPENNING submitted to this office for assessment prior to
6 AR-102 ROOF FLOOR PLAN
ELEVATION NUMBER
DG DOUBLE GLASS MP METAL PANEL approval of any such variation or additional.
LAU LAUNDRY MET METAL
7 AR-103 UPPER ROOF DECK PLAN STRUCTURAL MULTIPLE ELEVATION GAR GARBAGE N NORTH Supervision should be undertaken by a qualified
NATIONAL FIRE duly registered professional architect or civil
8 AR-104 FRONT & RIGHT SIDE ELEVATIONS 42 ST-01 STRUCTURAL NOTES DRWG. NO. WHERE DETAIL APPEARS
MACH RM MACHINE ROOM NFPA PROTECTIONA engineer.
ASSOCIATION
9 AR-105 LEFT & REAR ELEVATIONS 43 ST-02 STRUCTURAL STANDARD DETAILS DOOR NUMBER SWL SIDEWALK LEVEL NIC NOT IN CONTRACT THERMAL INSULATION NOTES:
DOOR NUMBER 1.All external walls, including roof deck and shafts
D5 # NUMBER NOM NOMINAL
10 AR-106 BUILDING SECTION A & B 54 ST-03 COLUMN LAYOUT
QTY QUANTITY
shall be 200mm. thick insulated block walls.
NTS NOT TO SCALE
AR-106A SCH SCHEDULE OA OVER ALL 2.All external columns,Beams including shafts shall
11 BUILDING SECTION C & D 45 ST-04 FOUNDATION LAYOUT OPENING NUMBER
SEC SECTION OC ON CENTER be insulated.
FRONT & RIGHT SIDE BOUNDARY WALL ELEVATIONS ARCH OPENNING
12 AR-106B 46 ST-05 GROUND FLOOR FRAMING LAYOUT SHO SHOWER OFFC OFFICE 3.All external glazing shall be insulated double as
WATER FEATURE DETAILS specified.
VERT VERTICAL OPP OPPOSITE
13 47 ST-06 FIRST FLOOR FRAMING LAYOUT HOR HORIZONTAL PCC PRECAST CONCRETE
4.All Roof shall be insulated.
AR-106C LEFT AND REAR BOUNDARY WALL ELEVATIONS
WINDOW/GLAZING/
5.All Car park and projection area celling shall be
WDW WINDOW PL PLASTIC insulated.
WINDOW OPENNING LOUVER OPENING NUMBER
14 AR-107 SCHEDULE OF DOORS AND WINDOWS 48 ST-07 ROOF FLOOR FRAMING LAYOUT W WIDTH PL LAM PLASTIC LAMINATE 6.Prior to construction, the contractor shall obtain a
POLYVINYL LIDENE copy of approved thermal insulation documents from
15 AP ACCESS PANEL PVDF
AR-107A SCHEDULE OF DOORS AND WINDOWS 49 ST-08 UPPER ROOF FRAMING LAYOUT FLOURIDE COATING M/s. Mohammad Al Gharib Architects & Engineers
CURTAIN WALL NUMBER
HM HOLLOW METAL QT QUARRY TILE whereas should be followed the same procedure.
16 AR-108 STANDARD DETAILS-1 50 ST-09 STRUCTURAL DETAILS CURTAIN WALL AFFL ABOVE FINISH FLOOR LEVEL R RISER
SCHEDULE OF FLOOR BEAMS ARCHITECTURAL CONCRETE
17 AR-109 STANDARD DETAILS - 2 51 ST-10 ACF RAD RADIUS
STRUCTURAL DETAILS FINISH
ACCESSORIES NUMBERS ALUM ALUMINUM RD ROOFDRAIN
18 AR-110 STANDARD DETAILS - 3 52 ST-11 SCHEDULE OF FOOTINGS, COLUMNS AMERICAN NATIONAL
AND GROUND BEAMS TOILET ACCESSORIES 05 ANSI REQD REQUIRED
STANDARD INSTITUTE
19 AR-110A AMERICAN SOCIETY FOR
STANDARD DETAILS - 4 53 ST-12 STRUCTURAL DETAILS ASTM RL ROAD LEVEL
TESTING MATERIAL
BLDG BUILDING RM ROOM
20 AR-110B STANDARD DETAILS - 5 54 ST-12A STRUCTURAL DETAILS SPACE NAME
BM BENCHMARK SD SMOKE DETECTOR
SPACE NUMBER
55 ST-13 SPACE NUMBER BS BRITISH STANDARD SHT SHEET
21 AR-111 SCHEDULE OF FINISHES STAIR DETAILS - 1
BTU BRITISH THERMAL UNIT SIM SIMILAR
22 AR-112 GREEN BUILDING DETAILS C° DEGREE CENTIGRADE/CELSIUS SP SPANDREL PANEL
LEVEL
CG CORNER GUARD SPEC SPECIFICATIONS
LEVEL IN PLAN
23 AR-113 STAIR PLAN, SECTION DETAILS CLG HT CEILING HEIGHT SS STAINLESS STEEL
LEVEL OF

ELECTRICAL LEVEL
℄
CLG
CENTER LINE
CEILING
STL
SSL
STEEL
STRUCTURAL SLAB LEVEL 1 : CONCEPT 2 : BUILDING PERMIT
1 C-01 COVER LEVEL IN ELEV./SECTION CONC CONCRETE T TRAD ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
LEVEL OF CM CENTIMETER TEMP TEMPERATURE
2 EL-01 ELECTRICAL FITTINGS,
SPECIDFICATIONS AND LEGEND DET DETAIL TER TERRAZO
GRID LINE (DASHDOT2) DIM DIMENSION TOS TOP OF SLAB
3 EL-02 ELECTRICAL STANDARD DETAILS GRID+BUBBLE+TEXT A DN DOWN TD TRENCH DRAIN
GRID REF. TEXT DT DATUM LEVEL TC TELEPHONE CLOSET
4 EL-03 GROUND FLOOR
POWER & AUXILLIARY LAYOUT DWG DRAWING TEL TELEOPHONE
FIRST FLOOR EC EXPOSED CONSTRUCTION THK THICK
5 EL-04 POWER & AUXILLIARY LAYOUT PRJECTION LINE EXPOSED CONSTRUCTION
LINE TYPE DASHDOT ECP TOW/P
ROOF FLOOR PAINTED
6 EL-05 POWER & AUXILLIARY LAYOUT ELEC ELECTRICAL TYP TYPICAL
UPPER ROOF ELEV ELEVATION UNO
7 EL-06 POWER & AUXILLIARY LAYOUT EXP JT EXPANSION JOINT VAR VARIES
HIDDEN LINE LINE TYPE HIDDEN
GROUND FLOOR EQ EQUAL VB VINYL BASE
8 EL-07 LIGHTING LAYOUT
VCT VINYL COMPOSITE TILES
9 EL-08 FIRST FLOOR EXT EXTERNAL VFT VINYL FLOOR TILES
LIGHTING LAYOUT
CONCRETE WORKS ENGR ENGINEER VP VISION PANEL
10 EL-09 ROOF FLOOR (COLUMNS, SLABS, BEAMS)
LIGHTING LAYOUT FA FIRE ALARM WC WATER CLOSET
FD FLOOR DRAIN W/ WITH
11 EL-10 UPPER ROOF DECK
LIGHTING LAYOUT FFL FINISH FLOOR LEVEL W/O WITHOUT
FHC FIRE HOSE CABINET WD WOOD
PLUMBING CONCRETE BLOCK MASONRY
FLR FLOOR WP WORKPOINT
MRS. FARAH RABEEA
FP FABRIC PANEL WR WATER RESISTANT
1 PL-01 DRAINAGE & WATER NOTES & LEGEND
BAHRAIN
1 FLOOR PLAN FPL FOOTH PATH LEVEL BATELCO TELECOMMUNICATIONS PROPOSED VILLA
2 PL-02 PLUMBING STANDARD DETAILS DRAWING ITEM TITLE AR-02 COMPANY
3 PL-03 WATER METER INSTALLATION DETAILS ELECTRICITY & WATER
FT FLOOR TRAP EWA JARI AL-SHAIK, KINGDOM OF BAHRAIN
AUTHORUTY
GROUND FLOOR
4 PL-04 DRAINAGE LAYOUT ELECTRICITY
TARGET REFERENCE GAL GALLON EDD DISTRIBUTION
PL-05 FIRST FLOOR DIRECTORATE
5 DRAINAGE LAYOUT
GALV GALVANZE
ROOF FLOOR
6 PL-06 GL GLASS
DRAINAGE LAYOUT
FINISHING GR GRANITE
UPPER ROOF DECK
7 PL-07 GLASS REINFORCED GYPSUM
DRAINAGE LAYOUT GRB
BOARD LIST OF DWGS.. LEGEND SYMBOLS
GROUND FLOOR GRP GLASS REINFORCED PLASTIC
8 PL-08 WATER DISTRIBUTION LAYOUT AND ABBREVIATION
GWB GYPSUM WALL BOARD
FIRST FLOOR
9 PL-09 HDW HARDWARE
WATER DISTRIBUTION LAYOUT
NORTH DIRECTION HM HOLLOW METAL
ROOF FLOOR Mr. MOHAMED AL GHARIB ARJ 24-002
10 PL-10 N HP HIGHPOINT
WATER DISTRIBUTION LAYOUT
WATER SUPPLY HR HOURS
11 PL-11
SCHEMATIC DIAGRAM HT HEIGHT

AR-001
 PROJECT ID: ARJ-24-002

NOTES:
TH All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
E and shall not be copied, printed or used for any
SI other purpose than specified.
TE
Figured dimensions only are to be used 'For
NORTH Construction' and any scaling of the drawing will be
PLOT LIMIT PLOT LIMIT
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

BOQ AREA
any discrepancies shall be addressed in writing to
BATH
this office, for clarification prior to the
1200X2200
JACUZZI
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
U/G WATER TANK

associated cost.
STORE
1200X2770
All drawings concerned shall be read along with all
relevant structural, electro- mechanical and all other
related drawings.
SWIMMING POOL SUN ROOM
4500X9500 4200X2200
(BY SPECIALIST)
SKY LIGHT LINE
Any claims for variations or additional shall be
submitted to this office for assessment prior to
approval of any such variation or additional.
INNER KITCHEN
4800X4300

Supervision should be undertaken by a qualified

duly registered professional architect or civil

SLIDING DOOR
engineer.
FRY KITCHEN
3600X6000

1
THERMAL INSULATION NOTES:
1.All external walls, including roof deck and shafts
2 VICINITY MAP shall be 200mm. thick insulated block walls.

DINING HALL STORE

2.All external columns,Beams including shafts shall
4200X5300
MAIN FAMILY TV. HALL
5200X5300 (DOUBLE HEIGHT)
3500X1600
be insulated.
3.All external glazing shall be insulated double as
specified.
FAMILY ENTRY
1450 WIDE
PORCH
1800 WIDE
4.All Roof shall be insulated.
SLDP-01
MULTIPLE SLIDING POCKET DOORS
1
2 5.All Car park and projection area celling shall be
2
3
1
insulated.
4
5 LIFT 6.Prior to construction, the contractor shall obtain a
1600x2500
6
7
copy of approved thermal insulation documents from
FORMAL MAJLIS
8
9 M/s. Mohammad Al Gharib Architects & Engineers
7100X5200 10
whereas should be followed the same procedure.
11 12 13 14

WASH
2300X1800 TOILET
2000X1800

GUEST ROOM
3000X3900

BATH STORE RM.

2600X1400
2900X2400

BATH GAS
1600X2550

PORCH
2100X1400

GARAGE
6400X6300

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
PLOT LIMIT PLOT LIMIT

ENTRANCE
AND EXIT

R O A D RESERVED

ROOF DECK
SKY LIGHT

UPPER ROOF DECK

PROPOSED TWO-STOREY VILLA + ROOF
07026597

WATER TANK COVERED

ROOF DECK
1 MASTER SITE DEVELOPMENT PLAN

MRS. FARAH RABEEA

AREA STATEMENT PROPOSED VILLA

NO. AREA NAME AREA JARI AL-SHAIK, KINGDOM OF BAHRAIN

01 GROUND FLOOR 243.00 M²

02 FIRST FLOOR 239.00 M²
03 ROOF FLOOR 78.00 M²
TOTAL B.U. AREA 560.00 M²
SITE DEVELOPMENT PLAN
04 PLOT AREA 535.30 M²
05 NET AREA 485.90 M²
06 PERCENTAGE OF BUILDING 90.80 % Mr. MOHAMED AL GHARIB ARJ 24-002

07 CAR PARKING 2 Nos

3 LOCATION PLAN
AR-002
 Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
1
Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
BATH
1600X2550
4500X9500
Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P. Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
(BY SPECIALIST)
SWIMMING POOL
JACUZZI

Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
Ramírez.
Suárez
Hugo
Arq.
de
Ramos.P.
Espitia
Francisco
Arq.
de
Arguelles.P.
Romero
A.
Adrian
Arq.
de
Hernández.P.
Guerrero
Enrique
Arq.
de
P.
5200X5300 (DOUBLE HEIGHT)

3000X3900
MAIN FAMILY TV. HALL

GUEST ROOM

1
2
SLIDING DOOR

7100X5200
FORMAL MAJLIS

PORCH
2100X1400
MULTIPLE SLIDING POCKET DOORS

9
8
7
6
5
4
3
2
1

10
4200X2200

SKY LIGHT LINE

4800X4300
SUN ROOM

4200X5300

BATH
2600X1400
INNER KITCHEN

DINING HALL

WASH
2300X1800
11 12 13 14
LIFT

GROUND FLOOR PLAN

2100 X 2510
1450 WIDE
FAMILY ENTRY
BOQ AREA

2900X2400
U/G WATER TANK

STORE RM.
TOILET
2000X1800

03
02
01
6400X6300
GARAGE

NO.
2
1
STORE
3500X1600
3600X6000
FRY KITCHEN

NET AREA
PORCH
BATH

1800 WIDE
STORE

GAS
1200X2770
1200X2200

AREA NAME

PERCENTAGE OF BUILDING
FIRST FLOOR PLAN
ROOF FLOOR PLAN
TOTAL
BATH
DRESS

2600X1800
2600X2500

( AREA /PLOT AREA) X 100% = (485.90 / 535.30) X 100%

3400X5200
5000X5300

BEDROOM-3 / GYM
DOUBLE HEIGHT

GROSS
4300X4500
BEDROOM-2
3500X5200
FAMILY HALL
PANTRY

9
8
7
6
5
4
3
2
1
H

10

NET
4200X7200
SKY LIGHT

A
ROOF DECK

M.BEDROOM

90.80 %
LEGENDS

239.00 M² 218.40 M²
GROUND FLOOR PLAN 243.00 M² 218.00 M²

78.00 M² 49.50 M²
560.00 M² 485.90 M²
L

- NET AREA
L
1600 WIDE
W

LIFT

FIRST FLOOR PLAN

2100 X 2510

- EXCLUDED AREA
4500X3900
A

BATH

BEDROOM-1
2600X1800
Y

11 12 13 14 15 16 17 18
19
21
20
22
23
24
25
26
27
28

SERVICE

28.50 M²
20.60 M²
25.00 M²

74.10 M²
DRESS
4200X4400
BATH
4200X3200

ROOF DECK
WATER TANK COVERED

9
8
7
6
5
4
3
2
1

10

DRY W.M
WASH
STORE
4200X4100

H
A
2100X3500

L
LAUNDRY

LIFT
2100 X 2510
1600 WIDE
W

11 12 13 14 15 16 17 18
BATH

A
2200X1600

19
2200X6000

20
21
22
23
24
25
26
MAID'S RM

ROOF FLOOR PLAN

SKY LIGHT
ROOF DECK

ISSUED FOR
engineer.

specified.

insulated.
NOTES:

be insulated.
associated cost.

related drawings.

1 : CONCEPT
at the Contractor's risk.

Mr. MOHAMED AL GHARIB

3 : CONSTRUCTION
4.All Roof shall be insulated.
other purpose than specified.

PROPOSED VILLA

NET AREA STATEMENT

MRS. FARAH RABEEA
THERMAL INSULATION NOTES:

4 : TENDER
PROJECT ID: ARJ-24-002

approval of any such variation or additional.

shall be 200mm. thick insulated block walls.

JARI AL-SHAIK, KINGDOM OF BAHRAIN

2 : BUILDING PERMIT
whereas should be followed the same procedure.
M/s. Mohammad Al Gharib Architects & Engineers
6.Prior to construction, the contractor shall obtain a

ARJ 24-002
copy of approved thermal insulation documents from
All designs and drawings are the sole property of

relevant structural, electro- mechanical and all other

Figured dimensions only are to be used 'For

3.All external glazing shall be insulated double as

M/s. Mohammad Al Gharib Architects & Engineers

Contractor shall be at full responsibility for any

and shall not be copied, printed or used for any

any discrepancies shall be addressed in writing to

5.All Car park and projection area celling shall be

submitted to this office for assessment prior to
this office, for clarification prior to the

All drawings concerned shall be read along with all

2.All external columns,Beams including shafts shall

1.All external walls, including roof deck and shafts
Any claims for variations or additional shall be
Construction' and any scaling of the drawing will be

Supervision should be undertaken by a qualified

Contractors are to verify all dimensions on-site and

commencement of the work, otherwise the

duly registered professional architect or civil

N/A
5 : AS BUILT
 4 PROJECT ID: ARJ-24-002
AR-105
A B C D E F G H I
NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
1 1 and shall not be copied, printed or used for any
BOQ AREA
other purpose than specified.
NORTH B C D Figured dimensions only are to be used 'For
AR-106 AR-106
AR-106 BATH
1200X2200 Construction' and any scaling of the drawing will be
JACUZZI
AL-01
at the Contractor's risk.
U/G WATER TANK

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
STORE associated cost.
1200X2770

All drawings concerned shall be read along with all

AL-01
relevant structural, electro- mechanical and all other
related drawings.
W-07
2 2 Any claims for variations or additional shall be
SWIMMING POOL SUN ROOM submitted to this office for assessment prior to
4500X9500 4200X2200
(BY SPECIALIST) approval of any such variation or additional.

W-06

W-06
SKY LIGHT LINE
Supervision should be undertaken by a qualified
duly registered professional architect or civil
W-08 engineer.
3 3
THERMAL INSULATION NOTES:
INNER KITCHEN 1.All external walls, including roof deck and shafts
4800X4300
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

W-08A
SLIDING DOOR
be insulated.

SLD-01
3.All external glazing shall be insulated double as
specified.
FRY KITCHEN 4.All Roof shall be insulated.
3600X6000
5.All Car park and projection area celling shall be
insulated.
W-05 6.Prior to construction, the contractor shall obtain a
1 copy of approved thermal insulation documents from
4 4
D-04A M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

W-04
DINING HALL STORE
4200X5300 3500X1600
MAIN FAMILY TV. HALL
5200X5300 (DOUBLE HEIGHT)
3 D-04 2
AR-105 AR-104
5 5
W-04

D-03
FAMILY ENTRY PORCH
1450 WIDE 1800 WIDE

2
6 MULTIPLE SLIDING POCKET DOORS
1
1
6
SLDP-01 2
3
4
5 LIFT 1 : CONCEPT 2 : BUILDING PERMIT
A 6
1600x2500 ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
AR-106
7
8
9
W-03

FORMAL MAJLIS
7100X5200 10

11 12 13 14
7 7
WASH

W-02
2300X1800 TOILET
D-06
2000X1800

8 8
GUEST ROOM
3000X3900 D-05
D-06

W-15
BATH STORE RM.
2600X1400

D-02
2900X2400

BATH GAS
W-02

1600X2550 D-01 D-05A

PORCH
9 GP-01 2100X1400 9
MRS. FARAH RABEEA
10 10
W-01
11 11 PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

GARAGE
6400X6300

GROUND FLOOR PLAN

12 SLG-01 12
GD-01 Mr. MOHAMED AL GHARIB ARJ 24-002

1 GROUND FLOOR PLAN A B C D E F

1
G H I
AR-104
AR-100
 4 PROJECT ID: ARJ-24-002
AR-105
A B C D E F G H I

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
1 1 and shall not be copied, printed or used for any
other purpose than specified.
NORTH B C D
AR-106 AR-106
AR-106
Figured dimensions only are to be used 'For
Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.
2 RG-01
2 Any claims for variations or additional shall be
SKY LIGHT submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

ROOF DECK duly registered professional architect or civil
SLD-01 W-11
engineer.
3 3
M.BEDROOM
4200X7200 THERMAL INSULATION NOTES:
D-09 1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.
BATH 2.All external columns,Beams including shafts shall
D-09 4200X3200
be insulated.

W-10
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
D-06
insulated.
W-05 DRESS 6.Prior to construction, the contractor shall obtain a
4200X4400
4 4 copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

W-04
DOUBLE HEIGHT
5000X5300
3 2
PANTRY D-05 W-12A
AR-105 AR-104
5 W-04 5

W-12
H A L L W A Y
1600 WIDE

W-14 28
6 1 27 6
2 26
3 25
4 24
5 LIFT 23
A 6
1600x2500 22 ISSUED FOR
1 : CONCEPT 2 : BUILDING PERMIT

AR-106 3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

7 21
8 20
BEDROOM-3 / GYM 9 19

W-13
W-03

3400X5200 10

11 12 13 14 15 16 17 18
7 7
FAMILY HALL
3500X5200

GP-01
D-05 D-05

W-02
D-05
D-06 BATH
8 2600X1800 8

BEDROOM-2
DRESS 4300X4500
2600X2500

D-06
W-02

9 BATH 9
2600X1800
GP-01

BEDROOM-1 MRS. FARAH RABEEA

10 4500X3900
10
11 11 PROPOSED VILLA
W-09 W-09

JARI AL-SHAIK, KINGDOM OF BAHRAIN

FIRST FLOOR PLAN

12 12
Mr. MOHAMED AL GHARIB ARJ 24-002

FIRST FLOOR PLAN 1

1 A B C D E F AR-104
G H I
AR-101
 4 PROJECT ID: ARJ-24-002
AR-105
A B C D E F G H I
NOTES:
All designs and drawings are the sole property of
NORTH M/s. Mohammad Al Gharib Architects & Engineers
1 1 and shall not be copied, printed or used for any
other purpose than specified.
B C D
AR-106 AR-106 Figured dimensions only are to be used 'For
AR-106
Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.
2 2 Any claims for variations or additional shall be
submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.
3 3
THERMAL INSULATION NOTES:
1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

STORE 2.All external columns,Beams including shafts shall

4200X4100 be insulated.
MAID'S RM ROOF DECK
3.All external glazing shall be insulated double as

W-12
2200X6000 specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
4 4 copy of approved thermal insulation documents from
D-07 M/s. Mohammad Al Gharib Architects & Engineers

W.M
whereas should be followed the same procedure.

SKY LIGHT
DRY
D-05A

WATER TANK COVERED LAUNDRY

2100X3500
D-06A

WASH
BATH
2200X1600

W-02
3 2
AR-105 AR-104
5 5

RC UPSTAND
D-07

W-12
D-08 H A L L W
1600 WIDE
A Y

6 1 6
2 26
3 25
4 24
5 LIFT 23 1 : CONCEPT 2 : BUILDING PERMIT
A 6
1600x2500 22 ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
AR-106
7 21
8 20
9 19
10

11 12 13 14 15 16 17 18

7 7

8 ROOF DECK 8

9 9
MRS. FARAH RABEEA
10 10
11 11 PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

ROOF DECK PLAN

12 12
Mr. MOHAMED AL GHARIB ARJ 24-002

1 ROOF FLOOR PLAN A B C D E F

1
G H I
AR-104
AR-102
 4
PROJECT ID: ARJ-24-002
AR-105
A B C D E F G H I
NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
1 1 and shall not be copied, printed or used for any
other purpose than specified.
NORTH B C D Figured dimensions only are to be used 'For
AR-106 AR-106
AR-106 Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.

2 2 Any claims for variations or additional shall be

submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.
3 3
THERMAL INSULATION NOTES:
1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
LOWER DECK 5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
4 4 M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

SKY LIGHT
WATER TANK COVERED

3 2
AR-105 AR-104
5 UPPER ROOF DECK 5

6 6

1 : CONCEPT 2 : BUILDING PERMIT

A ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
AR-106

7 7

8 LOWER ROOF DECK 8

9 9
MRS. FARAH RABEEA
10 10
11 11 PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

UPPER ROOF DECK PLAN

12 12
Mr. MOHAMED AL GHARIB ARJ 24-002

1 UPPER ROOF DECK PLAN 1

A B C D E F AR-104 G H I AR-103
 PROJECT ID: ARJ-24-002
A B C D E F G H I

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.
W-09 W-09 W-12A
Any claims for variations or additional shall be
submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

be insulated.
W-01 D-01 D-04 3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.
2 2
1 1

1 FRONT ELEVATION

12 11 10 9 8 7 6 5 4 3 2 1

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

W-12 W-02 W-12

W-02 W-13 W-12

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

W-02 D-03
W-06

D-02 W-15

FRONT ELEVATION AND RIGHT SIDE ELEVATION

2 2
1 1

Mr. MOHAMED AL GHARIB ARJ 24-002

2 RIGHT SIDE ELEVATION

AR-104
 I H G F E D C B A
PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.
W-11 SLD-01

Any claims for variations or additional shall be

submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
W-05 shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

W-08 be insulated.
W-07
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

2 REAR ELEVATION

1 2 3 4 5 6 7 8 9 10 11 12

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

W-10 W-04 W-04 W-03 W-02

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

SLD-01 W-03 W-02

W-06

LEFT SIDE ELEVATION AND REAR ELEVATION

Mr. MOHAMED AL GHARIB ARJ 24-002

1 LEFT SIDE ELEVATION

AR-105
 A B C D E F G H I PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
UPPER ROOF DECK and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.
ROOF DECK
RISER 154.00 All drawings concerned shall be read along with all
TREAD 300.00 relevant structural, electro- mechanical and all other
STEPS 26 Nos. related drawings.

Any claims for variations or additional shall be

submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.
BEDROOM 3/ GYM FAMILY HALL THERMAL INSULATION NOTES:
1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.
RISER 164.00
TREAD 300.00
STEPS 28 Nos.
2.All external columns,Beams including shafts shall
be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.

409 285 355

5.All Car park and projection area celling shall be
350
insulated.
6.Prior to construction, the contractor shall obtain a

215
copy of approved thermal insulation documents from
OUTDOOR M/s. Mohammad Al Gharib Architects & Engineers
AREA

985
±0.60 whereas should be followed the same procedure.
FORMAL MAJLIS STAIR AND LIFT OUTDOOR
AREA

250
100
250 140 1245
180 160

1 BUILDING SECTION A

1 2 3 4 5 6 7 8 9 10 11 12

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

ROOF DECK

FIX PANEL FIX PANEL

BEDROOM 3 / GYM. DRESS BATH RM. MRS. FARAH RABEEA

DOUBLE HT. PROPOSED VILLA

FIX PANEL
JARI AL-SHAIK, KINGDOM OF BAHRAIN

D-03

MAIN FAMILY TV HALL

OUTDOOR SITTING AREA FORMAL MAJLIS BATH RM. BUILDING SECTION A AND B
WATER LEVEL ADULT POOL)
SIDEWALK
SWIMMING POOL ROAD
(BY POOL SPECIALIST)
Mr. MOHAMED AL GHARIB ARJ 24-002

2 BUILDING SECTION B
AR-106
 1 2 3 4 5 6 7 8 9 10 11
PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
UPPER ROOF DECK and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.
STORE ROOF DECK
All drawings concerned shall be read along with all
relevant structural, electro- mechanical and all other
related drawings.
FIX PANEL Any claims for variations or additional shall be
submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.
M. BEDROOM FAMILY HALL BEDROOM 2
THERMAL INSULATION NOTES:
1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

FIX PANEL
FIX PANEL
be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
SUN ROOM INNER KITCHEN DINING FORMAL MAJLIS PORCH whereas should be followed the same procedure.
OUTDOOR SITTING AREA 2
1
ENTRANCE
SIDEWALK ROAD

1 BUILDING SECTION C

1 2 3 4 5 6 7 8 9 10 11 12

1 : CONCEPT 2 : BUILDING PERMIT

UPPER ROOF DECK ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

BATH
MAIDS ROOM STAIR AND LIFT ROOF DECK

BATH RM.
DRESS BATHROOM BEDROOM 1 MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

FRY KITCHEN PANTRY STAIR AND LIFT TOILET STORE BUILDING SECTION A AND B
OUTDOOR SITTING AREA GARDEN WATER. TANK GARAGE
SIDEWALK ROAD

Mr. MOHAMED AL GHARIB ARJ 24-002

2 BUILDING SECTION D
AR-106A
 PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
SEC-1 M/s. Mohammad Al Gharib Architects & Engineers
STONE CLADDING and shall not be copied, printed or used for any
COLOR AS PER ARCHITECT'S APPROVAL
other purpose than specified.
4400
Figured dimensions only are to be used 'For
200 50 Construction' and any scaling of the drawing will be
520 840 965 1670 405 STONE CLADDING
COLOR AS PER ARCHITECT'S APPROVAL
at the Contractor's risk.
50
Contractors are to verify all dimensions on-site and
any discrepancies shall be addressed in writing to

409 285 355

409 285 355

this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.
350

BUILDING LINE
1355 2505 540 All drawings concerned shall be read along with all
relevant structural, electro- mechanical and all other
related drawings.

215

215

215
2500
1760 2506 Any claims for variations or additional shall be

385
WATER FALLS
WATER FALLS
WATER FEATURE
submitted to this office for assessment prior to
WATER FEATURE
( BY SPECIALIST TO DETAIL )
( BY SPECIALIST TO DETAIL ) approval of any such variation or additional.

215

985

985
200 215
Supervision should be undertaken by a qualified

185

185
PLANTER BOX duly registered professional architect or civil
engineer.

200
THERMAL INSULATION NOTES:

250

250

250
PLANTER BOX
1.All external walls, including roof deck and shafts
SEC-1 50 shall be 200mm. thick insulated block walls.
500 2250 100 2.All external columns,Beams including shafts shall
250 140 be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
180 160 insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

1 FRONT BOUNDARY WALL ELEVATION 3 ELEVATION (WATER FEATURE) 4 SECTION A (WATER FEATURE)

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

FRONT & RIGHT SIDE

BOUNDARY WALL ELEVATIONS

Mr. MOHAMED AL GHARIB ARJ 24-002

2 RIGHT SIDE BOUNDARY WALL ELEVATION

AR-106B
 PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.

Any claims for variations or additional shall be

submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

1 REAR BOUNDARY WALL ELEVATION

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

LEFT SIDE & REAR

BOUNDARY WALL ELEVATIONS

Mr. MOHAMED AL GHARIB ARJ 24-002

2 LEFT SIDE BOUNDARY WALL ELEVATION

AR-106C
 PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
5. CONTRACTOR IS RESPONSIBLE TO DOUBLE CHECK QUANTITY OF DOORS AND WINDOWS. IRONMONGERY AND and shall not be copied, printed or used for any
OTHER REQUIRED ACCESSORIES FOR DOORS AND WINDOWS SHALL BE AS PER ARCHITECT'S SELECTION . PANIC
1. ALUMINUM WORKS SHALL BE THERMAL BREAK SERIES BY REYNARS OR APPROVED EQUAL. DEVICE/ HARDWARE TO BE POWDER COATED TO MATCH DOOR COLOR.
other purpose than specified.
W-04 a) CURTAIN WALLING SYSTEM 'CW50' SERIES WITH PRESSURE PLATE & CAPPING. 6.PROVIDE PROPRIETARY DOOR SEAL TO FRAMELESS GLAZED DOOR. Figured dimensions only are to be used 'For
W-03 b) CS86HI/ ECO 50 SERIES FOR FIXED & TILT AND TURN WINDOWS AS SHOWN.
c) CS59 (NON THERMAL) ALL ALUMINIUM INTERNAL DOORS AS SHOWN 7. CONTRACTOR TO ACQUIRE SPECIALIST SHOP DRAWINGS WITH DESIGN CALCULATIONS AS REQUIRED BY THE Construction' and any scaling of the drawing will be
2. GLASS TYPE G-1, DOUBLE GLAZING SCHEDULE SHALL BE AS FOLLOWS: (TO DOORS & WINDOWS) 6+12+6 ARCHITECT /SUPERVISING ENGINEER FOR APPROVAL PRIOR TO START OF FABRICATION AND/ OR INSTALLATION. at the Contractor's risk.
- 6mm FULLY TEMPERED TINTED GLASS OUTER PANE
- 12mm AIR-SPACE 8. ALL ALUMINUM DOORS & WINDOWS SHOULD BE PROVIDED WITH HEAVY DUTY HINGES, HANDLES, AND
- 6mm CLEAR FLOAT GLASS FULLY TEMPERED ACCESSORIES SHALL BE POWDER COATED TO APPROVED RAL COLOUR OF ALUMINIUM SECTIONS. Contractors are to verify all dimensions on-site and
9. THE INDICATED DIMENSIONS ARE THE FINISH OPENING DIMENSION. HOWEVER, THE FINAL OPENING DIMENSION any discrepancies shall be addressed in writing to
3. GLASS TYPE G-2, DOUBLE GLAZING SCHEDULE SHALL BE AS FOLLOWS FOR CURTAIN WALLS 8+12+6 :
-8mm FULLY TEMPERED TINTED GLASS OUTER PANE
SHOULD BE MADE IN COORDINATION WITH THE INTERIOR DESIGN DRAWING. this office, for clarification prior to the
F
-12mm AIR-SPACE 10. ALL EXTERNAL ALUMINUM DOORS TO HAVE WEATHER STRIP AS PER DESIGNERS SELECTION AND APPROVAL. commencement of the work, otherwise the
-6mm CLEAR FLOAT GLASS FULLY TEMPERED
Contractor shall be at full responsibility for any
11. ALL STAINLESS STEEL COMPONENTS & ACCESSORIES SHALL BE GRADE .316
4. GLASS TYPE G-3, DOUBLE GLAZING SCHEDULE SHALL BE AS FOLLOWS FOR BATHROOMS 6+12+6 associated cost.
- 6mm FULLY TEMPERED TINTED GLASS OUTER PANE
- 12mm AIR-SPACE
- 6mm FROSTED ANNEALED GLASS FULLY TEMPERED All drawings concerned shall be read along with all
FFL FFL
relevant structural, electro- mechanical and all other
related drawings.

Any claims for variations or additional shall be

submitted to this office for assessment prior to
F
F F F F approval of any such variation or additional.
W-01 W-02 W-03 W-04
W-06 W-07 Supervision should be undertaken by a qualified
duly registered professional architect or civil
G3
engineer.
TOP HUNG F F F F F F
SWING THERMAL INSULATION NOTES:
F 1.All external walls, including roof deck and shafts
SWING shall be 200mm. thick insulated block walls.
F
2.All external columns,Beams including shafts shall
G3 F F
be insulated.
F F F F F
3.All external glazing shall be insulated double as
FFL FFL FFL
specified.
FFL
4.All Roof shall be insulated.
W-01 W-02 W-03 W-04 W-06 W-07 5.All Car park and projection area celling shall be
COMBINATION OF FIXED & SWING GLASS WINDOW, POLYESTER
POWDER COATED ALUMINIUM 6mm+12mm+6mm THICK
COMBINATION OF FIXED GLASS WINDOW & SWING GLASS
WINDOW, POLYESTER POWDER COATED ALUMINIUM
COMBINATION OF FIXED / SWING GLASS
GLASS WINDOW, POLYESTER POWDER
COMBINATION OF FIXED / SWING GLASS
GLASS WINDOW, POLYESTER POWDER
FIXED WINDOW, POLYESTER POWDER
COATED ALUMINIUM 6mm+12mm+6mm
FIXED GLASS WINDOW/ ROOF,
POLYESTER POWDER COATED ALUMINIUM
insulated.
HERMETICALLY SEALED DOUBLE GLAZING. 6mm+12mm+6mm THICK HERMETICALLY SEALED DOUBLE
GLAZING.
COATED ALUMINIUM 6mm+12mm+6mm
THICK HERMETICALLY SEALED DOUBLE
COATED ALUMINIUM 6mm+12mm+6mm
THICK HERMETICALLY SEALED DOUBLE
THICK HERMETICALLY SEALED DOUBLE
GLAZING.
6mm+12mm+6mm THICK HERMETICALLY
SEALED DOUBLE GLAZING.
6.Prior to construction, the contractor shall obtain a
GLAZING. GLAZING. copy of approved thermal insulation documents from
GROUND. FLR._GUEST BEDROOM GROUND/ FIRST FLR._BATHROOMS
GROUND FLR._ FORMAL MAJLIS GROUND FLR._MAIN FAMILY/TV HALL GROUND FLR._ SUN ROOM GROUND FLR._ SUN ROOM
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

F F F

F F F
W-05

W-10 W-11 W-12 W-13

SLIDING SLIDING
1 : CONCEPT 2 : BUILDING PERMIT
SLIDING SLIDING
ISSUED FOR
F F SWING F SWING 3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
F F F

F F

F F
G3
F
F

W-08 W-09 W-10 W-05 W-11 W-12 W-13 W-14

SLIDING GLASS WINDOW, COMBINATION OF FIXED & SWING GLASS COMBINATION OF FIXED & SWING GLASS FIXED WINDOW, POLYESTER POWDER COMBINATION OF FIXED & SLIDING COMBINATION OF FIXED & SWING FIXED GLASS WINDOW, POLYESTER FIXED GLASS WINDOW, POLYESTER
POLYESTER POWDER COATED WINDOW, POLYESTER POWDER COATED WINDOW, POLYESTER POWDER COATED COATED ALUMINIUM 6mm+12mm+6mm WINDOW, POLYESTER POWDER COATED WINDOW, POLYESTER POWDER COATED POWDER COATED ALUMINIUM POWDER COATED ALUMINIUM
ALUMINIUM 6mm+12mm+6mm ALUMINIUM 6mm+12mm+6mm THICK ALUMINIUM 6mm+12mm+6mm THICK THICK HERMETICALLY SEALED DOUBLE ALUMINIUM 6mm+12mm+6mm THICK ALUMINIUM 6mm+12mm+6mm THICK 6mm+12mm+6mm THICK HERMETICALLY 6mm+12mm+6mm THICK HERMETICALLY
THICK HERMETICALLY SEALED HERMETICALLY SEALED DOUBLE GLAZING. HERMETICALLY SEALED DOUBLE GLAZING. HERMETICALLY SEALED DOUBLE HERMETICALLY SEALED DOUBLE SEALED DOUBLE GLAZING. SEALED DOUBLE GLAZING.
DOUBLE GLAZING. GLAZING. GLAZING. GLAZING.
GROUND FLR._FRY KITCHEN FIRST FLR._BEDROOM 1 AND 2 FIRST FLR._ M. BEDROOM GROUND FLR._ MAIN FAMILY TV/ HALL FIRST FLR._ BATH RM., M. BEDROOM FIRST/ROOF FLR._ HALLWAY/ MAID FIRST FLR._ STAIR LANDING FIRST FLR._ BEDROOM 3/ GYM

MRS. FARAH RABEEA

SLD-01

W-15 PROPOSED VILLA

W-08A

TOP HUNG SLIDING SLIDING

JARI AL-SHAIK, KINGDOM OF BAHRAIN
SWING

SHOWER
FIX GLASS
SWING
PARTITION

FFL

W-12A W-15 SLD-01 W-08A GP-01 D-09

COMBINATION OF FIXED & SWING TOP HUNG GLASS WINDOW, POLYESTER SLIDING GLASS WINDOW, SWING GLASS WINDOW, POLYESTER FIXED 10MM. THK. TEMPERED GLASS 12MM. THK. TEMPERED TINTED
WINDOW, POLYESTER POWDER COATED POWDER COATED ALUMINIUM POLYESTER POWDER COATED POWDER COATED ALUMINIUM PARTITION ON GLASS WITH STAINLESS STEEL SCHEDULE OF DOORS AND WINDOWS
ALUMINIUM 6mm+12mm+6mm THICK 6mm+12mm+6mm THICK HERMETICALLY ALUMINIUM 6mm+12mm+6mm 6mm+12mm+6mm THICK HERMETICALLY STAINLESS STEEL U SHAPE FRAME HINGES AND DOOR HANDLE
HERMETICALLY SEALED DOUBLE SEALED DOUBLE GLAZING. THICK HERMETICALLY SEALED SEALED DOUBLE GLAZING. ALL AROUND COMPLETE WITH ACCESORIES
GLAZING. DOUBLE GLAZING.
FIRST FLR._ DRESS GROUND FLR._ STORE ROOM GROUND FLR._INNER KITCHEN GROUND FLR._ FRY KITCHEN GROUND FLR. & FIRST FLR. MASTER SHOWER & WC
FIRST FLR._ M. BEDROOM ALL BATHROOMS

Mr. MOHAMED AL GHARIB ARJ 24-002

AR-107
 PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

1. ALUMINUM WORKS SHALL BE THERMAL BREAK SERIES BY REYNARS OR APPROVED EQUAL. 5. CONTRACTOR IS RESPONSIBLE TO DOUBLE CHECK QUANTITY OF DOORS AND WINDOWS. IRONMONGERY AND Construction' and any scaling of the drawing will be
OTHER REQUIRED ACCESSORIES FOR DOORS AND WINDOWS SHALL BE AS PER ARCHITECT'S SELECTION . PANIC at the Contractor's risk.
a) CURTAIN WALLING SYSTEM 'CW50' SERIES WITH PRESSURE PLATE & CAPPING. DEVICE/ HARDWARE TO BE POWDER COATED TO MATCH DOOR COLOR.
b) CS86HI/ ECO 50 SERIES FOR FIXED & TILT AND TURN WINDOWS AS SHOWN.
c) CS59 (NON THERMAL) ALL ALUMINIUM INTERNAL DOORS AS SHOWN 6.PROVIDE PROPRIETARY DOOR SEAL TO FRAMELESS GLAZED DOOR. Contractors are to verify all dimensions on-site and
2. GLASS TYPE G-1, DOUBLE GLAZING SCHEDULE SHALL BE AS FOLLOWS: (TO DOORS & WINDOWS) 6+12+6 7. CONTRACTOR TO ACQUIRE SPECIALIST SHOP DRAWINGS WITH DESIGN CALCULATIONS AS REQUIRED BY THE any discrepancies shall be addressed in writing to
- 6mm FULLY TEMPERED TINTED GLASS OUTER PANE
- 12mm AIR-SPACE
ARCHITECT /SUPERVISING ENGINEER FOR APPROVAL PRIOR TO START OF FABRICATION AND/ OR INSTALLATION. this office, for clarification prior to the
- 6mm CLEAR FLOAT GLASS FULLY TEMPERED 8. ALL ALUMINUM DOORS & WINDOWS SHOULD BE PROVIDED WITH HEAVY DUTY HINGES, HANDLES, AND commencement of the work, otherwise the
ACCESSORIES SHALL BE POWDER COATED TO APPROVED RAL COLOUR OF ALUMINIUM SECTIONS. Contractor shall be at full responsibility for any
3. GLASS TYPE G-2, DOUBLE GLAZING SCHEDULE SHALL BE AS FOLLOWS FOR CURTAIN WALLS 8+12+6 :
-8mm FULLY TEMPERED TINTED GLASS OUTER PANE 9. THE INDICATED DIMENSIONS ARE THE FINISH OPENING DIMENSION. HOWEVER, THE FINAL OPENING DIMENSION associated cost.
-12mm AIR-SPACE SHOULD BE MADE IN COORDINATION WITH THE INTERIOR DESIGN DRAWING.
-6mm CLEAR FLOAT GLASS FULLY TEMPERED
10.. ALL EXTERNAL ALUMINUM DOORS TO HAVE WEATHER STRIP AS PER DESIGNERS SELECTION AND APPROVAL.
All drawings concerned shall be read along with all
4. GLASS TYPE G-3, DOUBLE GLAZING SCHEDULE SHALL BE AS FOLLOWS FOR BATHROOMS 6+12+6 relevant structural, electro- mechanical and all other
11. . ALL STAINLESS STEEL COMPONENTS & ACCESSORIES SHALL BE GRADE .316
- 6mm FULLY TEMPERED TINTED GLASS OUTER PANE
- 12mm AIR-SPACE
related drawings.
- 6mm FROSTED ANNEALED GLASS FULLY TEMPERED
Any claims for variations or additional shall be
submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.
FIX PANEL FIX PANEL FIX PANEL

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
FFL FFL FFL FFL FFL FFL FFL FFL
5.All Car park and projection area celling shall be
D-03 insulated.
D-01 D-02 D-04 D-04A D-05 D-06 6.Prior to construction, the contractor shall obtain a
SINGLE LEAF SEMI SOLID CORE VENEERED WOOD DOUBLE LEAF SEMI SOLID CORE VENEERED
COMBINATION OF FIXED WINDOW 6MM+12MM+6MM THICK SEMI SOLID CORE WOODEN DOOR
DOOR / FRAME W/ ALUMINUM VERTICAL STRIPS
CLADDING & ARCHITRAVE,
SINGLE LEAF SEMI SOLID CORE VENEERED
WOOD DOOR & FRAME W/ ARCHITRAVE, HERMETICALLY SEALED DOUBLE GLAZING. & SEMI SOLID
SINGLE LEAF SEMI SOLID CORE VENEERED
WOOD DOOR & FRAME W/ ARCHITRAVE,
WOOD DOOR & FRAME W/ ARCHITRAVE,
DOOR HANDLE, DOOR CLOSER AND LOCKSET
SINGLE LEAF SEMI SOLID CORE VENEERED WOOD
DOOR & FRAME W/ ARCHITRAVE, VENEERED & FRAME WITH ARCHITRAVE. copy of approved thermal insulation documents from
CORE VENEERED DOOR FRAME, ARCHITRAVE WITH DOOR DOOR HANDLE DOOR CLOSER AND
DOOR HANDLE, DOOR CLOSER AND LOCKSET
(MOISTURE PROTECTIVE OUTSIDE FACE)
DOOR HANDLE, DOOR CLOSER AND
LOCKSET 1 HR. FIRE RATED HANDLE, DOOR CLOSER AND LOCKSET.
DOOR HANDLE, DOOR CLOSER AND
LOCKSET 1 HR. FIRE RATED
W/ VISION GLASS PANEL
(1 HR. FIRE RATED DOOR)
DOOR HANDLE, DOOR CLOSER AND LOCKSET
LOCKSET M/s. Mohammad Al Gharib Architects & Engineers
(WATERPROOF ON ONE SIDE)
GROUND FLR._FAMILY ENTRANCE
(WATERPROOF ON ONE SIDE)
FRY KITCHEN
WATER PROOF ON ONE SIDE.
whereas should be followed the same procedure.
GROUND_MAIN ENTRY/ ENTRY FOYER GROUND_STORE GROUND FLR. PANTRY ALL BEDROOMS ALL BATHROOMS

FFL FFL

D-05A D-06A D-07 D-08 AL-01

SEMI SOLID CORE WOODEN DOOR SEMI SOLID CORE WOODEN DOOR SEMI SOLID CORE WOODEN DOOR SINGLE LEAF POWDER COATED
SINGLE LEAF SEMI SOLID CORE VENEERED WOOD
ALUMINUM PANEL DOOR AND
DOOR & FRAME W/ ARCHITRAVE, VENEERED & FRAME WITH ARCHITRAVE. VENEERED & FRAME WITH ARCHITRAVE. VENEERED & FRAME WITH ARCHITRAVE.
FRAME. WITH DOOR HANDLE
1 : CONCEPT 2 : BUILDING PERMIT
DOOR HANDLE, DOOR CLOSER AND LOCKSET DOOR HANDLE DOOR CLOSER AND DOOR HANDLE DOOR CLOSER AND DOOR HANDLE DOOR CLOSER AND
(WATERPROOF ON ONE SIDE) LOCKSET LOCKSET LOCKSET DOOR CLOSER AND LOCKSET ISSUED FOR
WATER PROOF ON ONE SIDE. WATER PROOF ON ONE SIDE. WATER PROOF ON ONE SIDE. 3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

BATH RM. MAIDS TOILET AND BATH ROOF FLR. ROOF FLR.
LAUNDRY AND STORE RM. ROOF DECK/ STAIR GROUND FLR. BATHROOM (OUTDOOR)

MULTIPLE SLIDING POCKET DOORS

PLAN
CONCEALED RAIL GUIDE
(BY SPECIALIST)

GYPSUM BD. DRYWALL

ON METAL FRAME POCKET SLIDING DOOR, SEMI SOLID SLIDING
CORE VENEERED WOODEN DOOR &
FRAME WITH RAIL GUIDE AND FLOOR
TRACKS
(BY SPECIALIST)

SLIDING SLIDING SLIDING SLIDING

CONCEALED FLOOR TRACKS

MRS. FARAH RABEEA
(BY SPECIALIST)

GD-01 SLG-01 PROPOSED VILLA

ELEVATION DOUBLE LEAF METAL DOOR & FRAME W/ MANUALLY/ ELECTRICALLY OPERATED SLIDING
SLDP-01 VERTICAL GRILL WOODEN COLOR FINISH. METAL GATE & FRAME W/ VERTICAL GRILLS
W/ METAL HINGES, DOOR HANDLE AND LOCK WOODEN COLOR FINISH.
POCKET SLIDING DOOR, SEMI SOLID
CORE VENEERED WOOD DOOR & FRAME
W/ COMPLETE ACCESORIES FOR SLIDING GATE
JARI AL-SHAIK, KINGDOM OF BAHRAIN
WITH RAIL GUIDE, FLOOR TRACKS AND
DOOR HANDLE MAIN GATE GARAGE

MAIN FOYER, HALLWAY

SCHEDULE OF DOORS AND WINDOWS

Mr. MOHAMED AL GHARIB ARJ 24-002

AR-107A
 PROJECT ID: ARJ-24-002

NOTES:
NOTES All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
GENERAL IRONMONGERY SCHEDULE and shall not be copied, printed or used for any
ALL DIMENSIONS MENTIONED IN SCHEDULE ARE other purpose than specified.
1 STRUCTURE OPENING SIZES. CONTRACTOR TO
ALLOW FOR FINISHES. TYPICAL DOOR FRAME DETAILS Figured dimensions only are to be used 'For
SET AREA DESCRIPTION REMARKS SCALE 1:5 MTS.
ALL DOORS HAVE 12-15 MM CLEARANCE FROM Construction' and any scaling of the drawing will be
2
FIN.FL. at the Contractor's risk.
ALL IRONMONGERY SETS LISTED SHALL BE
FROM APPROVED MANUFACTURER (REFER 40 1 Contractors are to verify all dimensions on-site and
3 50 1
SPECIFICATIONS). HINGES 3"X4" D.S.S.W. 2 PAIR ENT. any discrepancies shall be addressed in writing to
DOOR LEVER HANDLES ON BACK this office, for clarification prior to the
LOCKING ARRANGEMENTS TO HAVE ONE
4 PLATE WITH APPROPRITE OVAL

44 20

44 20
MASTER KEY TO APPROVAL. commencement of the work, otherwise the

10
ALL DOOR CLOSER SHALL BE SURFACE CYLINDER LOCK AND CASE Contractor shall be at full responsibility for any
5 COMPLETE. DUMMY HANDLES ON associated cost.
MOUNTED. A MAIN ENTRY
MIN. DISTANCE FROM KNOBSET CENTRE TO BACK PLATE (2 NOS.); EASY

BLOCK WALL THICKNESS

6 CLEAN SOCKET (1NO.); DOOR All drawings concerned shall be read along with all
EDGE OF THE DOOR SHALL BE 90 MM.
ALL DOORS TO HAVE 3 WALL ANCHORS ON EACH CLOSER 1 NO. 90° HOLD OPEN; relevant structural, electro- mechanical and all other
7 FLOOR DOOR STOP 2 NOS.; DOOR related drawings.
JAMB FOR MANSONRY / CONCRETE WALLS.
THIS DRAWING IS INDICATIVE AND NOT TO BE VIEWER 1 NO.
Any claims for variations or additional shall be
USED FOR CONSTRUCTION. CONTRACTOR TO BLOCK WALL submitted to this office for assessment prior to
SUBMIT FULL SHOP DRAWINGS SHOWING HINGES 3"X4" D.S.S.W. 1 - 21" PAIR; approval of any such variation or additional.
8
REINFORCEMENTS, ANCHORS AND FIXING LEVER HANDLES ON BACK PLATE
DETAILS TO ARCHITECT PRIOR TO PLACING AN WITH APPROPRIATE OVAL Supervision should be undertaken by a qualified
ORDER. CYLINDER LOCK AND CASE duly registered professional architect or civil
engineer.

10
WOODEN DOORS B KITCHEN COMPLETE. DOOR CLOSER 1 NO.

20

20
90° HOLD OPEN; FLOOR DOOR
ALL FIRE RATED DOORS SHALL BE 54 MM THK STOP 1 NO. THERMAL INSULATION NOTES:
SOLID CORE FLUSH DOORS. 1.All external walls, including roof deck and shafts
15 50 15 50 shall be 200mm. thick insulated block walls.
ALL FIRE RATED DOORS SHALL HAVE
INTUMESCENT SEALING STRIPS ALL AROUND.
TYPE-1 TYPE-2 2.All external columns,Beams including shafts shall
be insulated.
HINGES 3"X4" D.S.S.W. 1 - 21" PAIR; 3.All external glazing shall be insulated double as
ALL OTHER DOORS SHALL BE 45 MM THK
LEVER HANDLES ON BACK PLATE specified.
DECORATIVE HARDWOOD (ASHWOOD) FINISHED 50 1
1 WITH APPROPRIATE OVAL 4.All Roof shall be insulated.
WITH CLEAR POLYURATHENE LAQURED TO C BEDROOM
CYLINDER LOCK AND CASE 5.All Car park and projection area celling shall be
APPROVAL.
COMPLETE. FLOOR DOOR STOP 1 insulated.

44 20
ALL FRAMES, ARCHITRAVES, FILLER PIECES
NO. 6.Prior to construction, the contractor shall obtain a
2 SHALL H.W.(MERANTI) FINISH SAME AS DOOR copy of approved thermal insulation documents from

10
TO APPROVAL. M/s. Mohammad Al Gharib Architects & Engineers
18 MM MARINE PLYWOOD SUB-FRAME FOR ALL whereas should be followed the same procedure.
3 DOORS TREATED AROUND EDGES WITH

BLOCK WALL THICKNESS

CAPRINOL PAINT. HINGES 3"X4" D.S.S.W. 1 - 21" PAIR;
ALL IRONMONGERY SHALL BE FROM APPROVED LEVER HANDLES ON BACK PLATE
4
MANUFACTURE REFER SPECS. D BATHROOM WITH BATHROOM LOCK +
ALL IRONMONGERY TO HAVE POLISHED BRASS EMERGENCY RELEASE.
5
FINISH TO APPROVAL. BUFFERED COAT HOOK (1NO.)
DOOR STOP SHALL BE FLOOR OR WALL
6
MOUNTED TO SUIT LOCATION TO APPROVAL.

10

20
TYPICAL THRESHOLD DETAIL
TYPE 'T2'
15 50
TYPE-3
GLAZING TYPE :
1 : CONCEPT 2 : BUILDING PERMIT
G-1 (DOUBLE GLAZING) ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
6 MM TH. TOUGHENED GREEN REFLECTIVE GLASS. +
℄ 12MM THK. SPACE + 6MM CLEAR

G-2 (DOUBLE GLAZING)

SAME AS G1 EXCEPT INTERNAL PANEL 6 MM THK.
FROSTED GLASS

GENERAL NOTES:

TYP. ALUMI. WINDOW JAMB DETAILS

NOTES :
1) THIS DETAIL IS INDICATIVE. TYPICAL THRESHOLD
2) CONTRACTOR TO SUBMIT FULL SHOP DRAWING INCLUDING (ROOFDECK UPSTAND) DETAIL
TYPICAL THRESHOLD DETAIL
FIXING DETAILS, (CONSIDERING INTERNAL AND EXTERNAL TYPE 'T3' MRS. FARAH RABEEA
FINISHES) AND ALL SAMPLES TO ARCHITECT FOR APPROVAL.
TYPE 'T1'
3) ALL TIMBER USED FOR SUB FRAME & ROUGH GROUNDS SHALL
PROPOSED VILLA
BE TREATED TO APPROVAL.
4) EXTENDED ROUGH GROUNDS, ALUM. FLANGE OR FLASHING
SHALL BE PROVIDED WHEREVER THERE IS DIFFERENCE IN JARI AL-SHAIK, KINGDOM OF BAHRAIN
THICKNESS OF INTERNAL & EXTERNAL FINISHES.

SPECIFICATIONS:
1) ALL ALUMINIUM SECTIONS TO BE POWDER COATED BALEXCO
SYSTEM IN RAL COLOUR WITH 24mm DG UNIT COMPRISING OF
6mm COLOURED REFLECTIVE(OUTSIDE) + 12mm AIR SPACER +
6mm CLEAR FLOAT/OBSCURED(INSIDE) GLASS & COLOUR TO STANDARD DETAILS 1
APVL.
2) ALL SINGLE LINES SHOWN SHALL HAVE 1/2" WIDE SEALANT
JOINTS EXTERNALLY (BOTH WAYS) WITH ALUMINIUM FRAMES
INTERNALLY. Mr. MOHAMED AL GHARIB ARJ 24-002

AR-108
 PROJECT ID: ARJ-24-002

NOTES:
INSIDE OUTSIDE INSIDE OUTSIDE All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

INSIDE
Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
STRUCTURAL SLAB this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
50MM EXTRUDED POLYSTERENE associated cost.

OUTSIDE All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.

Any claims for variations or additional shall be

AUTOCLAVED AERATED submitted to this office for assessment prior to
CONCRETE (AAC) BLOCKS THERMAL INSULATION FOR THERMAL INSULATION FOR approval of any such variation or additional.
CONCRETE SHEAR WALL, BEAMS & COLUMNS EXPOSED FLOOR LEVELS
Supervision should be undertaken by a qualified
duly registered professional architect or civil
engineer.

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

be insulated.
3.All external glazing shall be insulated double as
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

NOTES:
1. ALL EXTERNAL WALLS SHALL BE 200 MM THK 8" STANDARD DETAILS 2
TYP. PARAPET DETAIL AUTOCLAVED AERATED BLOCK
2. REST ARE ORDINARY BLOCK WALLS AS DIMENSIONED ON PLANS.
Mr. MOHAMED AL GHARIB ARJ 24-002

AR-109
 PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to

A
SSL SSL this office, for clarification prior to the
TYPICAL JOINTS FOR BLOCKS SECTION A-A commencement of the work, otherwise the
TO BEAMS AND COLUMNS Contractor shall be at full responsibility for any
CORNER WALL associated cost.
ELEVATION (DOOR) ELEVATION (WINDOW)
All drawings concerned shall be read along with all
relevant structural, electro- mechanical and all other
related drawings.
TYP. DET. OF LINTEL BEAM
AT CHB WALL OPENING Any claims for variations or additional shall be
submitted to this office for assessment prior to
approval of any such variation or additional.
OPENING OR END WALL FLR. SLAB OR BEAM
Supervision should be undertaken by a qualified
NOTE: duly registered professional architect or civil
engineer.

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
SLAB shall be 200mm. thick insulated block walls.

2.All external columns,Beams including shafts shall

TYP. PARAPET DETAIL be insulated.
3.All external glazing shall be insulated double as
INTERSECTION WALL INTERSECTING R.C. COL. OR WALL specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
TYPICAL CONNECTION DETAIL OF REINFORCED MASONRY WALL insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
FLR. SLAB OR BEAM M/s. Mohammad Al Gharib Architects & Engineers
BEAM whereas should be followed the same procedure.

TYPICAL SLAB & BEAM TYP. SECTION OF MASONRY

CONSTRUCTION JOINT DET. PARTITION REINFORCEMENTS

NOTE:

TYP. CONCRETE SLAB OPENING DET. 1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

MID-INTERSECTION

TYPICAL RC WALL DOOR & WINDOW OPENING TYPICAL CORNER SLAB DETAIL

CORNER

MRS. FARAH RABEEA

TYP. CONCRETE WALL
TYPICAL CONNECTION DETAIL
OF RC WALL AT CORNERS REINF. DETAIL PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

RF. DECK CAT LADDER DET.

STANDARD DETAILS 3

TYP. DETAIL OF SUNKEN SLAB

SCALE mm N.T.S Mr. MOHAMED AL GHARIB ARJ 24-002

AR-110
 PROJECT ID: ARJ-24-002

GENERAL NOTES NOTES:

1.0 Contractor shall verify all levels at site prior to execution of work and in case of any discrepancies, bring to knowledge of the
All designs and drawings are the sole property of
engineer. M/s. Mohammad Al Gharib Architects & Engineers
2.0 The Contractor shall confirm the settingout and finish floor level of building and dimensions prior to commencement of work and shall not be copied, printed or used for any
and in case of any discrepancies bring to knowledge of the engineer.
other purpose than specified.
3.0 The Contractor shall obtain all approvals and N.O.C.'s from all concerned local statutory authorities and shall include for all Figured dimensions only are to be used 'For
works with respect to the diversion/protection of the services during the period of construction, to the satisfaction of the Construction' and any scaling of the drawing will be
concerned authorities and the engineer. at the Contractor's risk.
4.0 All block wall partitions shall be taken to the underside of the structural slab above unless noted otherwise.
Contractors are to verify all dimensions on-site and
5.0 All internal openings and sleeves for services in walls/slabs shall be sealed with fire safing and external sleeves with water
any discrepancies shall be addressed in writing to
proofing sealants and flashings all around to ensure that entire assembly is weather tight and provides the required fire rating. this office, for clarification prior to the
commencement of the work, otherwise the
6.0 The contractor shall provide a damp proof course within external blockwall at the finished floor level of the ground floor and Contractor shall be at full responsibility for any
provide water proofing in wet areas such as toilets, pantry, shafts etc. to the satisfaction of engineer. associated cost.
7.0 External wall plaster shall be 20 mm thick, internal wall plaster shall be 15 mm thick U.N.O. All drawings concerned shall be read along with all
8.0 The plaster work throughout the building shall be to the full height upto soffit of beams/slabs where there is no ceiling and in
relevant structural, electro- mechanical and all other
case of suspended ceiling, plaster shall extend 200 mm above suspended ceiling. related drawings.

9.0 Plaster shall be with all accessories such as metal lath corner beads, plaster stop, control joint, trims, etc. The accessories for Any claims for variations or additional shall be
external plaster shall be of stainless steel and for internal plaster shall be of galvanised steel. 139 278
submitted to this office for assessment prior to
approval of any such variation or additional.
10.0 The contractor shall provide metal lath over the junction of R.C. work and block work prior to plaster. 139

Supervision should be undertaken by a qualified

11.0 Internal finish floor thicknesses (except for fairfaced finish floors) shall be 75mm at all floor finish (e.g. terrazzo, marble,stone
tiling etc.) U.N.O. and the main contractor shall allow for screed beneath the floor finish. 2 DUCT PENETRATION THRU ROOF SLAB TREADS AND RISER DETAIL
duly registered professional architect or civil
5 engineer.
12.0 The ceramic wall tiles shall be bonded to rendered wall with approved adhesive with matching colour grout. The Main
Contractor shall include for mortar, adhesive, edge trims, etc. The overall thickness for wall finishes including rendering shall THERMAL INSULATION NOTES:
be 25mm. The tiles shall extend 200 mm above false ceiling U.N.O. The supply of ceramic tiles is covered by provisional 1.All external walls, including roof deck and shafts
rate in the document. shall be 200mm. thick insulated block walls.
13.0 The ceramic tiles at floor shall be fixed with waterproof adhesive over screed. Overall thickness shall be 75 mm U.N.O. All
tiles shall be fully grouted with matching colour grout, colour as selected by engineer. The contractor shall include for 2.All external columns,Beams including shafts shall
waterproofing, adhesive, mortar bedding. The supply of ceramic tiles is covered with provisional rate in documents. be insulated.
14.0 Contractor shall prepare detailed shop drawings of toilet areas to an appropriate scale, indicating floor & wall tile layouts, 3.All external glazing shall be insulated double as
work points, locations of sanitary fittings, toilet accessories, floor drains, clean outs, access panels, etc. prior to execution of specified.
work. 4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
15.0 The contractor shall provide movement control joints at 3000 mm center to center in both directions with sealant and backing
rod as directed by engineer U.N.O.
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
16.0 The marble/granite stone flooring shall be laid in matching colour to form pattern. Contractor shall include for special cut and M/s. Mohammad Al Gharib Architects & Engineers
brush applied water proofing compound to rear side and all edges. Marble/granite shall be bedded in sand with white cement whereas should be followed the same procedure.
mortar.
6 RAIN WATER PIPE DETAIL
17.0 The contractor shall prepare detailed shop drawings for all the false ceiling works to a scale as directed by the engineer after
co-ordination with all services and MEP contractor, indicating the finishes, fixings, supports, materials, service outlets work
points, etc., prior to execution of related works.

18.0 Substations shall be constructed as per requirement of Electricity Authority. The contractor shall obtain necessary details from
Electricity Authority prior to execution of the work and shall include to provide removable painted chequred plate with
supporting angle over trenches.
19.0 The contractor shall provide plinths and foundations to water tanks and all mechanical equipments. For size, location and
inserts etc. co-ordinate with relevant contractor prior to execution, provide 2" thick vibration insulation material below all
mechanical equipments such as A/Cs, pumps. fans, etc. U.N.O.

20.0 All exposed aluminium profiles shall be PVDF coated, colour to match the engineer's samples.

21.0 All aluminium openable windows shall be with complete hardware, ie. hinges, handles, locks, stays, latches, etc. All
ironmorngery to be powder coated to match aluminium sections.
22.0 All aluminium doors and glass doors shall be with complete hardware.

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

3 KERB SECTION DETAILS

SEE DETAIL-2

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

STANDARD DETAILS 4
7 WATER PROOFING DETAIL

Mr. MOHAMED AL GHARIB ARJ 24-002

1 PIPE PENETRATION THRU ROOF SLAB 4 PAVING DETAILS @ LANDSCAPE AREA

AR-110A
 PROJECT ID: ARJ-24-002

NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
other purpose than specified.

Figured dimensions only are to be used 'For

Construction' and any scaling of the drawing will be
at the Contractor's risk.

Contractors are to verify all dimensions on-site and

any discrepancies shall be addressed in writing to
this office, for clarification prior to the
commencement of the work, otherwise the
Contractor shall be at full responsibility for any
associated cost.

All drawings concerned shall be read along with all

relevant structural, electro- mechanical and all other
related drawings.

Any claims for variations or additional shall be

submitted to this office for assessment prior to
approval of any such variation or additional.

Supervision should be undertaken by a qualified

duly registered professional architect or civil
engineer.

THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

(150mm MIN.)
2.All external columns,Beams including shafts shall

VARIES
be insulated.
3.All external glazing shall be insulated double as

50
specified.
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

FLOOR SLAB
( BATHROOMS & PANTRY )

8 WATER PROOFING DETAIL @ WET AREA 9 BETWEEN INTERNAL FLOOR AND TERRACE

1 : CONCEPT 2 : BUILDING PERMIT

ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

MRS. FARAH RABEEA

PROPOSED VILLA

JARI AL-SHAIK, KINGDOM OF BAHRAIN

STANDARD DETAILS - 5

10 ROOF DRAIN DETAIL - 02 Mr. MOHAMED AL GHARIB ARJ 24-002

AR-110B
 PROJECT ID: ARJ-24-002
FINISHING SCHEDULE
SPACE GENERAL NOTES
FLOOR WALLS SKIRTING CEILING NOTES:
NAME All designs and drawings are the sole property of
GROUND FLOOR ALL ITEMS LISTED IN THIS SCHEDULE AND/OR SHOWN OTHER RELEVANT DRAWINGS SHALL BE FROM M/s. Mohammad Al Gharib Architects & Engineers
1
APPROVED MANUFACTURER. REFER PARTICULAR SPECIFICATIONS. and shall not be copied, printed or used for any
FORMAL MAJLIS/
MAIN FAMILY TV 600X600mm THICK NON-SLIP 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
other purpose than specified.
3-COATS EMULSION OVER 12MM THK. PLASTER WHEREVER INTERNAL WALL FINISHED ONLY AS EMULSION OR OIL PAINT, THE SURFACES TO HAVE 12mm
HALL CERAMIC TILES 2 THK. CEMENT/SAND SMOOTH FINISH PLASTER AND TO BE FINISHED WITH TWO COATS OF MAJUN, ONE Figured dimensions only are to be used 'For
DINING HALL 600X600mm THICK NON-SLIP COAT OF PRIMER AND MIN. TWO COATS OF PAINT TO ARCHITECT'S APPROVAL. Construction' and any scaling of the drawing will be
3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
INNER KITCHEN CERAMIC TILES at the Contractor's risk.
3 ALL WET AREAS TO HAVE WATERPROOFING SYSTEM TO APPROVAL (TORCH APPLIED).
STAIR MARBLE TILES 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH MARBLE TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD Contractors are to verify all dimensions on-site and
any discrepancies shall be addressed in writing to
300X300mm THICK NON-SLIP 300X300mm PORCELAINE WALL this office, for clarification prior to the
PAINTED 12 mm THK. MOISTURE RESISTED GYPSUM 4 ALL GYPSUM BOARDS USED IN THIS CONTRACT SHALL BE MOISTURE RESISTANT.
WASH & TOILET
CERAMIC TILES CERAMIC TILES commencement of the work, otherwise the
- BOARD
Contractor shall be at full responsibility for any
CONTRACTOR TO PROVIDE M.R. GYPSUM BOARD BULKHEAD ON METAL FRAMING BEHIND associated cost.
400X400mm THICK NON-SLIP 400X400mm PORCELAINE WALL PAINTED 12 mm THK. MOISTURE RESISTANT
FRY KITCHEN 100mmH CERAMIC TILES 5 SPANDREL/BLANK OFF PANEL IF STRUCTURAL ELEMENT DOES NOT EXIST. AND WHEREVER THERE IS
CERAMIC TILES CERAMIC TILES GYPSUM BOARD All drawings concerned shall be read along with all
CHANGE IN LEVEL OF SUSPENDED CEILING.
relevant structural, electro- mechanical and all other
600X600mm THICK NON-SLIP
ALL WALL AREAS WITH SUSPENDED CEILINGS ARE TO BE FINISHED AS SPECIFIED, MIN. 100 ABOVE related drawings.
3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD SUSPENDED CEILING LEVEL AND ALL GAPS AND JOINTS IN MASONRY WALLS, AS WELL AS IN
GUEST RM. CERAMIC TILES 6
STRUCTURAL SLAB SOFFIT, ABOVE SUSPENDED CEILING SHALL BE SEALED WITH CEMENT AND SAND Any claims for variations or additional shall be
600X600mm THICK NON-SLIP PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
MORTAR/PUTTY TO APPROVAL. submitted to this office for assessment prior to
DRESSING RM. 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES approval of any such variation or additional.
CERAMIC TILES
7 ALL GAPS AND JOINTS IN WET AREAS TO BE SEALED WITH CLEAR SILICON SEALANT TO APPROVAL.
300x300 mm CERAMIC NON-SLIP Supervision should be undertaken by a qualified
TILES ON APPROVED - PAINTED 12 mm THK. MOISTURE RESISTANT duly registered professional architect or civil
BATH RM. 300X300mm PORCELEIN WALL TILES UP TO CEILING LEVEL.
WATERPROOFING SYSTEM GYPSUM BOARD engineer.
8 ALL O.T.S. SERVICE PLATFORM; REFER DRG.
300X300mm THICK NON-SLIP PAINTED 12 mm THK. MOISTURE RESISTANT
PANTRY 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES
GYPSUM BOARD
THERMAL INSULATION NOTES:
CERAMIC TILES 1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.
400X400mm THICK NON-SLIP 9 ALL DUST PROOFERS AND HARDENERS SHALL BE SODIUM SILICATE BASED OR SIMILAR TO APPROVAL.
STORE RM. 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
CERAMIC TILES
2.All external columns,Beams including shafts shall
300x300 mm CERAMIC NON-SLIP be insulated.
PAINTED 12 mm THK. MOISTURE RESISTANT ALL VERTICAL SERVICE PIPES TO BE ENCLOSED WITH M.R. GYPSUM BOARD ON G.I. FRAMING AND 3.All external glazing shall be insulated double as
BATH RM. TILES ON APPROVED 300X300mm PORCELEIN WALL TILES UP TO CEILING LEVEL. - 10
GYPSUM BOARD FINISHED AS ADJACENT WALLS TO APPROVAL. specified.
WATERPROOFING SYSTEM
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
11 ALL PLUMBING SHAFTS TO BE SEALED AT EVERY FLOOR TO APPROVAL. insulated.
6.Prior to construction, the contractor shall obtain a
copy of approved thermal insulation documents from
12 ALL RATES MENTIONED IN THIS SCHEDULE ARE FOR SUPPLY ONLY. M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

SUPPLY RATE OF CERAMIC TILES IN BATH INCLUDING BORDER TILES AND DECORATIVE PATTERN TILE
13
ON WALL. REQUIRED TO APPROVAL.

FIRST F L O O R
14 OVERALL FLOOR FINISH SHALL BE 50MM THICK. UNLESS MENTIONED OTHERWISE.

STAIR MARBLE TILES 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED SMOOTH SOFFIT SLAB
ALL EXTERNAL CONC./MASONRY WALL SURFACES BEHIND CLADDINGS/SPANDREL OR BLANK-OFF PANEL
15
600X600mm THICK NON-SLIP TO HAVE MIN. 2 COATS OF BITUMINOUS PAINT AS VAPOR BARRIER TO APPROVAL.
MASTER BEDROOM 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
CERAMIC TILES
PLASTER IS NOT REQUIRED BEHIND FULL LENGTH MIRROR ABOVE VANITY COUNTER. PLASTER AND TILE
BEDROOM 600X600mm THICK NON-SLIP 16
3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD FINISH REQUIRED BEHIND FRAMED MIRROR.
1, 2, 3/ GYM CERAMIC TILES
300x300 mm CERAMIC NON-SLIP CERAMIC TILES ON KITCHEN/BATH FLOORS NOT TO EXTEND BELOW/BEHIND KITCHEN COUNTER &
PAINTED 12 mm THK. MOISTURE RESISTANT 17
ALL BATHROOMS TILES ON APPROVED 300X300mm PORCELEIN WALL TILES UP TO CEILING LEVEL. - BATHTUBS.
GYPSUM BOARD
WATERPROOFING SYSTEM
300x300 mm CERAMIC NON-SLIP 1 : CONCEPT 2 : BUILDING PERMIT
MASTER PAINTED 12 mm THK. MOISTURE RESISTANT WALL FINISH BEHIND KITCHEN CABINETS & WARDROBES SHALL BE 12MM THICK SMOOTH FINISH ISSUED FOR
TILES ON APPROVED 300X300mm PORCELAIN WALL TILES UP TO CEILING LEVEL. - 18 3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT
BATHROOMS GYPSUM BOARD PLASTER , AND FLOORING NOT REQUIRED BELOW WARDROBES AND KITCHEN CABINETS.
WATERPROOFING SYSTEM
600X600mm THICK NON-SLIP PAINTED 12 mm THK. ORDINARY GYPSUM BOARD BOUNDARY WALL SHALL BE FINISHED WITH EPOXY PAINT SYSTEM ON 3/4" TH. RENDER COMPLETE WITH
DRESSING RM. 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES
CERAMIC TILES 19 RENDER STOP 6" ABOVE EXTERNAL FINISHED LEVEL & MASTIC FILLED FLEXCELL JOINTS AT MAX. 10'-8"
C/C (TO BE CHECKED ON SITE)
FAMILY HALL 600X600mm THICK NON-SLIP
3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
CORRIDOR/ LOBBY CERAMIC TILES
20 ALL INTERNAL WALLS OF PLANTER TO HAVE 2 COATS OF BITUMINOUS PAINT.

ROOF DECK
21 ALL GARDENS AND PLANTER FILL AREAS TO HAVE 12" SWEET SOIL TOPPING.
STAIR MARBLE TILES 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED SMOOTH SOFFIT SLAB

ROOFING SYSTEM ( MAIN ROOF )

400X400mm THICK NON-SLIP
MAID RM. 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. ORDINARY GYPSUM BOARD
CERAMIC TILES
300x300 mm CERAMIC NON-SLIP
PAINTED 12 mm THK. MOISTURE RESISTANT A CEMENT/SAND SCREED 1:4 LAID TO FALL MIN. THICKNESS 1-1/2"
MAID BATH RM. TILES ON APPROVED 300X300mm PORCELEIN WALL TILES UP TO CEILING LEVEL. -
GYPSUM BOARD
WATERPROOFING SYSTEM

STORE RM. & 300X300mm THICK NON-SLIP 3-COATS EMULSION OVER 12MM THK. PLASTER 100mmH CERAMIC TILES PAINTED 12 mm THK. MOISTURE RESISTANT 4 MM MODIFIED BITUMEN BASED WATERPROOFING MEMBRANE REINFORCED WITH NON-WOVEN
B
LAUNDRY CERAMIC TILES GYPSUM BOARD POLYESTER TORCH APPLIED OVER PRIMER.

MRS. FARAH RABEEA

C 75 MM THK. EXTRUDED POLYESTYRENE AS INSULATION.
EXTERNAL
PROPOSED VILLA
MAIN ENT. PORCH PAINTED 12 mm THK. MOISTURE RESISTANT
20mm THICK GRANITE 3-COATS EMULSION OVER 12MM THK. PLASTER - D SEPARATION SHEET LAYER, REFER SPECIFICATIONS.
FAMILY ENT. PORCH GYPSUM BOARD
OUTER SITTING JARI AL-SHAIK, KINGDOM OF BAHRAIN
AREA - - - 20" X 20" X 2" THK. REINFORCED CONC. TILES WITH SULPHATE RESISTING ADDITIVES AND CHANFERED
POOL DECK E
TOP EDGES LAID LOOSE.
400X400mm THICK NON-SLIP PAINTED 12 mm THK. MOISTURE RESISTANT
BALCONY - -
CERAMIC TILES GYPSUM BOARD
A GRAVEL FILL AT EDGES AND AT PIPE PENETRATIONS. MIN. 6" WIDE AND WHEREVER FULL TILE
F
WALKWAY STONE TILES - - CANNOT BE LAID.
-
GARAGE/ - - PARAPETS TO BE DRESSED UP WITH MINERAL CHIP FINISH WATERPROOFING MEMBRANE WHEREVER
DRIVEWAY STONE TILES - G SCHEDULE OF FINISHES
EXPOSES, MIN. 12" HIGH.
APPVD. ROOF DECK
ROOF DECK WATERPROOFING SYSTEM 3-COATS EMULSION OVER 12MM THK. PLASTER - -
ROOF TILE FINSH
300x300 mm CERAMIC NON-SLIP Mr. MOHAMED AL GHARIB ARJ 24-002
OUTDOOR PAINTED 12 mm THK. MOISTURE RESISTANT
TILES ON APPROVED 300X300mm PORCELEIN WALL TILES UP TO CEILING LEVEL. -
BATHROOMS GYPSUM BOARD
WATERPROOFING SYSTEM

GATE ENTRANCE STONE TILES - - -

AR-111
 PROJECT ID: ARJ-24-002

NO 1 - Article 22 - Enabled Access NO 2 - Article 26 - Heat Island and heat Exhaust NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
A- Heat island other purpose than specified.
B- Heat exhaust NO 9 - Article 82 - Condensate Drainage Figured dimensions only are to be used 'For
Construction' and any scaling of the drawing will be
at the Contractor's risk.
Slope roof Flat Roof

Split exhaust units RFL Contractors are to verify all dimensions on-site and
any discrepancies shall be addressed in writing to
60x60
FROM ACs & SONDENSED this office, for clarification prior to the
landing area Window AC commencement of the work, otherwise the
Condition
Low-wind
(0-2 m/s)
Medium -wind
(2-6 m/s)
High -wind
(2-6 m/s)
WATER SOURCES Contractor shall be at full responsibility for any
associated cost.
black surface temperature 376.8 K 355.6 K 334.2 K
All drawings concerned shall be read along with all
relevant structural, electro- mechanical and all other
White surface temperature 322.4 K 317.8 K 313.9 K
related drawings.
Ramp Steps surface temperature 333.9 K 325.2 K 317.8 K
Any claims for variations or additional shall be
submitted to this office for assessment prior to
Solar reflectance index (SRI) 78.9 80.3 81.1
minimum air approval of any such variation or additional.
Solar reflectance : 0.66 Solar absorptace: 0.34
FFL condensate brake of 25 mm Supervision should be undertaken by a qualified
Emittance : 0.9 Temperature unit: Kelvin [k]
duly registered professional architect or civil
drain pipe engineer.

*. Refer to roof details in thermal sheet THERMAL INSULATION NOTES:

1.All external walls, including roof deck and shafts
shall be 200mm. thick insulated block walls.

NO 3 - Article 28 - Light Colors on Building Exterior NO 4 - Article 56 - Air Conditioning -Design Parameters 2.All external columns,Beams including shafts shall
be insulated.
3.All external glazing shall be insulated double as
waste specified.
4.All Roof shall be insulated.
Selected colour :- REGAL/ WHITE water pipe 5.All Car park and projection area celling shall be
insulated.
SRI = 88 Total U value (0.57) 6.Prior to construction, the contractor shall obtain a
Refer to thermal insulation calculation in the system copy of approved thermal insulation documents from
LRV =75 M/s. Mohammad Al Gharib Architects & Engineers
whereas should be followed the same procedure.

TO MANHOLE & DRAINAGE LINE

NO 5 - Article 65 - Electronic Ballasts NO 6 - Article 75 - Electricity metering NO 10 - Article 83 - Condensate Recovery

1 : CONCEPT 2 : BUILDING PERMIT
ISSUED FOR
3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

ELECTRONIC BALLASTS TO BE FIXED WITHIN THE LIGHTING SYSTEM SUB metering to be fixed refer to ' E ' sheet
BMS OR CCMS SYSTEM TO BE INSTALLED FROM ACs & SONDENSED
Refer to ' E ' Sheets WATER SOURCES

NO 7 - Article 76 - Air Conditioning Metering NO 8 - Article 77 - Central Control & monitoring system minimum air
Sub Meters for chilled water supply for individual units BMS OR CCMS SYSTEM TO BE INSTALLED condensate brake of 25 mm
a.
drain pipe
b. (BMS)
Housing units Housing units

MRS. FARAH RABEEA

waste PROPOSED VILLA

sub meters sub meters
water pipe
JARI AL-SHAIK, KINGDOM OF BAHRAIN
Readings Readings
Energy Energy
utitity utitity

User data Indivdual and User data

total bill list of costs total bill GREEN BUILDING DETAIL
list of costs

TO MANHOLE & IRRIGATION

AREAS OR RECYCLE TANK Mr. MOHAMED AL GHARIB ARJ 24-002

Property manager Property manager

AR-112
 F H PROJECT ID: ARJ-24-002
100 4700 100
200 1200 2100 1200 200
NOTES:
All designs and drawings are the sole property of
M/s. Mohammad Al Gharib Architects & Engineers
and shall not be copied, printed or used for any
6 1 6 other purpose than specified.
2 26
9 TREADS@ 300 MM. =2700

7 TREADS@ 300 MM. =2700

Figured dimensions only are to be used 'For
3 25
Construction' and any scaling of the drawing will be
4 24 at the Contractor's risk.
5 LIFT 23
1600x2500 22 Contractors are to verify all dimensions on-site and
6
3500

3500
any discrepancies shall be addressed in writing to
SEC-1 7 21 SEC-1 this office, for clarification prior to the
8 20 commencement of the work, otherwise the
9 19 Contractor shall be at full responsibility for any
associated cost.
10
All drawings concerned shall be read along with all
1300

1300
7 7 relevant structural, electro- mechanical and all other

500
related drawings.

800
500

11 12 13 14 15 16 17 18
UPPER ROOF DECK
Any claims for variations or additional shall be
1500 5 TREADS @ 300MM. = 1500 1500
submitted to this office for assessment prior to
200 200 approval of any such variation or additional.
4700 LED HIDDEN STRIP LIGHTS
100 100
TREADS & RISERS FINISHES Supervision should be undertaken by a qualified
duly registered professional architect or civil
F H SCREED AND MORTAR BEDDING

STAIR RC SLAB
TREADS engineer.

3 ROOF FLOOR STAIR PLAN (VERIFY STRUCT'L DWG.)

THERMAL INSULATION NOTES:

RISER
TREADS
WITH ANTI-SLIP GROUVES
1.All external walls, including roof deck and shafts
SPACING AS PER shall be 200mm. thick insulated block walls.

4000
MANUFACTURER'S STANDARD

2.All external columns,Beams including shafts shall

RISER
F H LED HIDDEN STRIP LIGHTS
(BY I.D.) be insulated.
100 4700 100 3.All external glazing shall be insulated double as
200 200
specified.
1200 2100 1200
4.All Roof shall be insulated.
5.All Car park and projection area celling shall be
insulated.

1000
28
6.Prior to construction, the contractor shall obtain a
6 1 27 6 TREAD AND RISER DETAILS - 1 26
copy of approved thermal insulation documents from
M/s. Mohammad Al Gharib Architects & Engineers
2 26 5 RISER 154.00 25 whereas should be followed the same procedure.
9 TREADS@ 300 MM. =2700

9 TREADS@ 300 MM. =2700

24
3 25 TREAD 300.00 23
4 24 22
LIFT STEPS 26 Nos. 21
5 23 20
1600x2500 22 19
6
3500

3500

18
SEC-1 7 21 SEC-1 17
16
8 20 15
9 19 14
13

4000
10 12

14000
800

11
1300

10
7 7 9
100

100

11 12 13 14 15 16 17 18 8
7
4 NOS. EXPANSION BOLTS 6
5
1200 7 TREADS @ 300MM. = 2100 1200 4
200 200 50MM. DIA STAINLESS STEEL 3
4700
HANDRAIL MIRROR FINIH 2
100 100 1 1 : CONCEPT 2 : BUILDING PERMIT
FULLY WELD GRIND AND SMOOTH 28 ISSUED FOR

F H 26
27 3 : CONSTRUCTION 4 : TENDER 5 : AS BUILT

2 FIRST FLOOR STAIR PLAN 25

24
STAINLESS STEEL FLANGE RISER 164.00 23
22
CONNECTOR BOLTED TO WALL TREAD 300.00 21
20
F H STEPS 28 Nos. 19
30MMØ DIA. STAINLESS STEEL FULLY 18
4700 100
WELD TO 50MM DIA. STAINLESS STEEL 17
200 50 200
16
3250 1200 HANDRAIL 15
100
14

4600
13
12
200

11
10
6 HANDRAIL FIXING DETAILS - 2 9
8
7
2050

6
FAMILY ENTRY 5 STAIR AND LIFT
1450 WIDE 4

1400 (AS PER LIFT MANUFATURER/ SUPPLIER)

3
2
6 DOORS
1
2
6 1
7 TREADS@ 300 MM. =2100

1 MRS. FARAH RABEEA

2

300 300
7 TREADS@ 300 MM. =2700

3
4 PROPOSED VILLA
5 LIFT
6
1600x2500
3500

3500

JARI AL-SHAIK, KINGDOM OF BAHRAIN

SEC-1 7 SEC-1
8
9
1400
1200

10

7 7 4 STAIR DETAIL SECTION 1

100

11 12 13 14
700

STAIR DETAILS

200 1200 7 TREADS @ 300MM. = 2100 1200

200
100 4700
100
Mr. MOHAMED AL GHARIB ARJ 24-002

F H
1 GROUND FLOOR STAIR PLAN
AR-113