Scribd
Upload
439 views1 page

Snice Mirage 2000 Plan v2 Final

This document provides a parts list and assembly instructions for building a model airplane called a Mirage 2000. It lists various parts that are needed such as rear and inner fuses, elevon cuts, servos, and doublers. It also provides information on control throws, suggested battery and motor setup, wing area, length, weight range, center of gravity location, and design credits. The goal is to build a 55mm EDF jet plane with a slightly nose heavy CG for initial flights.

Uploaded by

Lalith Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
439 views1 page

Snice Mirage 2000 Plan v2 Final

This document provides a parts list and assembly instructions for building a model airplane called a Mirage 2000. It lists various parts that are needed such as rear and inner fuses, elevon cuts, servos, and doublers. It also provides information on control throws, suggested battery and motor setup, wing area, length, weight range, center of gravity location, and design credits. The goal is to build a 55mm EDF jet plane with a slightly nose heavy CG for initial flights.

Uploaded by

Lalith Kumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

X2

SERVO

OUTTER REAR FUSE

X2

X2

INNER DUCT TOP

REAR TOP FUSE DOUBLER 2 REAR TOP FUSE DOUBLER 1

X2

X2
SERVO

INNER REAR FUSE

X2

REAR BOTTOM DOUBLER 1 REAR BOTTOM DOUBLER 2

X2

X2

INNER DUCT SIDE

ELEVON CUT

ELEVON CUT

X1 X2
KFM4 PANEL TOP

MAIN WING WING SPAR POSITION

X2

CG POINT MAKE PLANE SLIGHTLY NOSE HEAVY FOR INITIAL FLIGHTS

X2
KFM4 PANEL BOTTOM

SERVO

AB ST AR SP
VERT. STAB. RUDDER CUT

VERT. STAB. SUPPORT

MIRAGE 2000 55MM EDF W/S: 22 LENGTH: 33.25 AUW: 17.8-20.4OZ LIPO: 3S; 1300-2200MAH CG: 7.375 AFT OF INTAKE 5MM FOAM BOARD DESIGNED BY: SNICE

X11
X2

CANOPY - LAMINATE & SAND TO SHAPE

X2

TURTLEDECK DOUBLER 2 TURTLEDECK DOUBLER 1

55MM FAN HOLDER/BRACE

FORWARD FUSE TOP DOUBLER 1

X2

X2

FORWARD FUSE TOP DOUBLER 2

X2
X2

FORWARD FUSE SIDE

55MM FAN HOLDER/BRACE

FORWARD FUSE BOTTOM DOUBLER 1


X2

FORWARD FUSE BOTTOM DOUBLER 2

X8

NOSE CONE

X1

FRONT FUSE FORMER

CONTROL THROWS (LOW/HIGH): THIS SQUARE SHOULD MEAS. UP ELEVON:0.5 / 0.75 1X1 FOR 100% SCALE BUILD DOWN ELEVON:0.5 / 0.75 AILERON:0.25 / 0.5 RUDDER:1.0 / 1.0 **EVEN ON LOW RATES, PLANE IS VERY RESPONSIVE. LAUNCH ON LOW RATES!

REAR FUSE BOTTOM

X1

X1

BOTTOM FUSE

FORWARD FUSE TOP

X1

TURTLE DECK TOP

X1

X1

TOP FUSE

You might also like