8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 1

Section 9 - Transverse Conveyors

BS2/... Transverse conveyors are designed to transfer pallets for short transport distances (e.g. between two rectangular lines) or as cycle-independent workstations. The BS2, BS2/M, and BS2/K are powered units that use standard or antistatic toothed belts for pallet transport. The BS2/0 is a non-powered toothed belt unit designed to be driven

by a standard BS2 using a special drive coupling, thus saving the cost of a gearbox and motor. Unless otherwise stated, transverse conveyors are reversible. Flat-top chain and roller chain BS2 units are available in standard and heavy duty configurations and provide increased payload carrying capacity.

Specify conveyor width, length, conveyor speed, motor voltage/frequency, motor position, and motor orientation when ordering. The LG2 lift gate kit provides personnel and vehicle access through a conveyor line and uses a standard BS2 unit.

60

60

60

WA

RN

ING

PULL HAN

DLE TO LO CK

BS2 Transverse Conveyors 9-2 to 9-3

60

LG2 Lift Gates 9-4 to 9-5

60

BS2/O Transverse Conveyors 9-6 to 9-7

150

BS2/M Transverse Conveyors BS2/M 9-8 to 9-9

200

BS2/K Transverse Conveyors 9-10 to 9-11

450

BS2/C Flat-top Chain Transverse Conveyors 9-12 to 9-13

BS2/C-H H.D. Flat-top Chain Transverse Conveyors 9-14 to 9-15

BS2/R Roller Chain Transverse Conveyors 9-16 to 9-17

BS2/R-H H. D. Roller Chain Transverse Conveyors 9-18 to 9-19

9- 2

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Transverse Conveyor
Model BS2

60

Transverse conveyors are most often used to transfer workpiece pallets between parallel conveyor sections. They are also used to construct cycle-independent workstations, or small systems with short conveying lengths. The unit itself is modular and comes with its own midmounted or outboard mounted drive and pre-installed toothed belts. Workpiece pallet movement can be reversed if desired. In normal operation, the maximum load capacity for transverse conveyors is 60 kg forward and 30 kg in reverse. In addition, positioning and control modules can be mounted on transverse conveyors. Transverse conveyors are available in any length from 240 mm to 6000 mm in 5 mm increments. Specify conveyor width, length, conveyor speed, motor voltage/ frequency, motor position, motor orientation and belt version when ordering.

Outboard Mounted Motor Orientation

Transverse conveyors come fully assembled and include all required mounting hardware. Motor voltage and frequency options are described in table 9-1. NOTE: Transverse conveyor widths (B) in excess of 160 mm are available with either a mid-mounted or outboard mounted motor as shown. Please contact our applications engineering department for non-standard length, width, speed, or voltage.
Pallet Flow Pallet Flow 180 270 90 0

Motor Position
L

Ordering Information for Transverse Conveyor BS2

Specify part number, then select from the options below. Width (B) in mm Motor Position Motor Orientation (outboard mount only) Belt Version Transverse Conveyor length (L) Nominal Conveyor Speed (m/min)** Motor Voltage/Frequency
* Mid-mounted motor not available in 160 mm wide transverse conveyors. ** Full load conveyor speeds vary depending on motor frequency. See table 9-1

Your Choices are: 160, 240, 320, 400, 480, 640, 800, 1040 R, M*, L 0, 90, 180, 270 Non-Antistatic (N) Antistatic (A) 240 mm to 6000 mm (in 5 mm increments) 6, 9, 12, 15, 18** See Table 9-1

Part Number 3842 999 716 Your selection: ____________ mm ____________ ____________ ____________ ____________ mm ____________ m/mm ________ V ________ Hz

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 3

Technical data for BS2

Nominal belt speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60 Hz Motor electrical specifications = See Table 9-1 = 60 kg = 30 kg = 1400 = 1700 = See Table 9-1

Electrical data for BS2

Actual Speed HP Full Load Amps @ Nom. 50Hz M/min 50 Hz 60 Hz 60Hz 208/60 240/60 380/50 415/50 480/60 575/60 .24 1.6 1.3 0.86 0.72 0.67 0.55 6 6.1 7.4 .28 .24 1.6 1.3 0.86 0.72 0.67 0.55 9 9.1 8.9 .28 .24 1.6 1.3 0.86 0.72 0.67 0.55 12 12.2 11.1 .28 .24 1.6 1.3 0.86 0.72 0.67 0.55 15 15.2 14.8 .28 .24 1.6 1.3 0.86 0.72 0.67 0.55 18 18.3 18.5 .28 Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings.

Table 9-1

Dimensional data for BS2

205 Motor mounting L

130

80 mm Profile Mounting
B 100 B+2 B + 40 B 75
80mm belt conveyor profile 80mm belt conveyor profile

Motor mounting = R
20mm T-bolt

BS 2, BS 2/O drive

50mm T-bolt

20mm T-bolt

205

B 100 B+2 B + 40

100 mm Profile Mounting

100mm belt or chain conveyor profile 100mm belt or chain conveyor profile

Motor mounting = M 30 L
BS 2, BS 2/O drive 20mm T-bolt 50mm T-bolt 50mm T-bolt 20mm T-bolt

15

95 102 320

Transverse conveyor width (BWT) must match pallet length (LWT ) or width (BWT), depending on orientation.

10

130

9- 4

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Lift Gate
Model LG2

The lift gate provides personnel and vehicle access through a conveyor line by utilizing a BS2 transverse conveyor (ordered separately). The lift gate kit consists of hinges and pneumatic lift struts on one end, and rest support brackets on the other. It is typically used to provide worker access to the inside of a line for maintenance or assembly processes. It can also be used to provide a through way on long in-line sections. The pneumatic lift struts ease the lifting effort and provide an additional measure of safety, while the hinge features an automatic locking mechanism to prevent accidental closure. A proximity switch mounting kit is included to prevent flow into the open lift gate.

WA

RN

ING

PULL HAN

DLE TO LOC K

Pneumatic Lift Struts

Lift gate kits are available in pallet widths from 160-800 mm, and two different pneumatic lift struts are used depending upon BS2 length. Standard lift struts handle BS2 conveyors in length ranges of 1010 to 1310 mm while high capacity

lift struts are used for BS2 conveyors in length ranges of 1315 to 1610 mm. Lift gate kits can be mounted in any of the four basic configurations shown on page 9-5. NOTE: The hinge end must be mounted to the drive end of the BS2.

9
Dimensional Data for LG2

Length of BS 2 6mm
WARNING!
PULL SAFETY HANDLE IN DIRECTION INDICATED BY ARROWS TO LOCK LIFT GATE WHENEVER OPENED. FAILURE TO LOCK GATE MAY RESULT IN SERIOUS INJURY

9mm

AS2/B

UM2/B

PU LL HA ND LE TO LO CK

Standard= (L) range 1010 1310 or High capacity= (L) range 1315 1610
350

Lift gate width (B) must match pallet length (LWT) or width (BWT), depending on orientation.

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 5

Ordering Information for LG2

Specify part number, then select from the options below. Lift Gate width (B) in mm Hinge end mounting Rest end mounting Allowable BS2 length (L) range Your Choices are: 160, 240, 320, 400, 480, 640, 800 AS2B / UM2B*, BS2, T-Line, KE2** AS2B / UM2B, BS2, T-Line, KE2, RK2 Specify length range: 1010 - 1310 or 1315 - 1610 Part Number 8981 999 238 Your selection: ____________ mm _______________ _______________ _______________

* Hinge end mounting to AS2B / UM2B is only available with a mid-mount motor mount. ** Hinge end mounting to KE2 requires an additional mounting kit (included). 160mm requires BS2 with outboard mounted motor and includes special hinge mounting bracket. 240mm and larger requires BS2 with mid-mounted motor. Not compatible with flat-top chain or roller chain drives/returns. Consult Applications Engineering for modified standard options.

Lift Gate Configurations (NOTE:

The hinge end must be mounted to the drive end of the BS2)
Hinge Lift Gate AS2B Drive

Powered curve configuration The lift gate is connected to the powered curve, mounting to either the hinge end or the rest end. An additional mounting kit is included and requires a 185mm gap.

KE2 /90 or 180

Rest

Leg Set* 185 KE2 Mounting Kit

9
AS2B Drive

In-Line Drive to Return The lift gate is installed between two standard conveyor sections, attaching to the drive on one end, and the return on the other.

UM2B Return

Hinge Lift Gate

Rest Leg Set*

In-Line transverse conveyor The lift gate connects two standard BS 2 transverse conveyors.

BS2 Transverse Conveyor

Hinge

Lift Gate

BS2 Transverse Conveyor

Rest Leg Set*

T-Line configuration The lift gate spans the gap between two parallel conveyor lines and transfers pallets onto and off the main lines with lift-transfer units.

LTU Rest Hinge LTU

Lift Gate

* Leg sets are required for the connecting module at the hinge end mount.

Leg Set*

9- 6

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Transverse Conveyor
Model BS2/O

60

Transverse conveyors are most often used to transfer workpiece pallets between parallel conveyor sections. They are also used to construct cycle-independent workstations, or small systems with short conveying lengths. The BS2/O is not powered and is driven by a standard BS2 operating in the same direction via a special coupling (see page 9-7). Workpiece pallet movement can be reversed if desired, dependent on the coupled BS2. In normal operation, the combined maximum load capacity for the powered and slave driven transverse conveyor is 60 kg forward and 30 kg in reverse. Positioning and control modules can also be mounted to transverse conveyors.

Transverse conveyors are available in any length from 240 mm to 6000 mm in 5 mm increments. Specify conveyor width, length, and belt version when ordering. Transverse conveyors come fully assembled and include all required mounting hardware.

Please contact our applications engineering department for special applications. NOTE: To order drive coupling components for standard applications see page 9-7.

Ordering Information for Transverse Conveyor BS2/O

Specify part number, then select from the options below. Width (B) in mm* Belt Version Transverse Conveyor length (L) Your Choices are: 160, 240, 320, 400, 480, 640, 800, 1040 Non-Antistatic (N) Antistatic (A) 240 mm to 6000 mm (in 5 mm increments) Part Number 3842 999 724 Your selection: ____________ mm _______________

____________ mm

* Transverse conveyor width (B) must match pallet length (LWT) or width (BWT), depending on orientation.

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 7

Dimensional Information for BS2/O

BS 2/0

B - 100

118

Forward

B + 40

B+2

Reverse
BS 2

102

10

130

30

BS 2/0

BS 2

43

BOSCH

118

65

17 mm Hex Shaft

BS 2

40

BS 2/0

Ordering Information for BS2/O Drive Couplings

BS2
B

40

BS2/O
B

a
Male-to-male coupling BS2 Male-to-female coupling BS2 Hex shaft Cover tube Male-to-female coupling BS2/O

BS2/O

25

a - 81.5 a - 41.5 a - 25

Male-to-male coupling 3 842 218 921

for (a) = 50 mm

Male-to-female coupling 3 842 218 920

(2 reqd.) for (a) = 85 to 1500 mm

Hex shaft 3 842 992 521/...

L = a 41.5 mm for (a)= 85 to 1500 mm

Cover tube 3 842 992 038/...

L = a 81.5 mm for (a)= 85 to 1500 mm

a = Distance between BS2 and BS2/O

9- 8

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Transverse Conveyor
Model BS2/M

60

Transverse conveyors are most often used to transfer workpiece pallets between parallel conveyor sections. They are also used to construct cycle-independent workstations, or small systems with short conveying lengths. The unit itself is modular and comes with its own midmounted or outboard mounted drive with toothed belts. Mounting the drive in the center of the conveyor's length rather than at its end makes the BS2/M more compact, making it suitable for areas with limited clearance. In addition, positioning and control modules can be mounted at the very end of transverse conveyors. In normal configuration, the maximum load capacity for the BS2/M is 60 kg in the forward direction and 30 kg in reversed direction. However payload will be reduced to 30kg forward and reverse if the length of L1 is not one third or less of the overall length (L).

Transverse conveyors are available in any length from 310 mm to 6000 mm in 5 mm increments. Specify conveyor width, length, conveyor speed, motor voltage/ frequency, motor mounting and belt version when ordering. Transverse conveyors come fully assembled and include all required mounting hardware. Motor voltage and frequency options are described in table 9-2. NOTE: Transverse conveyor widths (B) in excess of 160 mm are available with either a mid-mounted motor or the outboard mounted motor as shown.

Outboard Mounted Motor Orientation

180 Pallet Flow 270 90 0

Motor Position
L

Pallet Flow

Ordering information for Transverse Conveyor BS2/M

Specify part number, then select from the options below. Width (B) in mm Motor Position Motor Orientation (outboard mount only) Belt Version Transverse Conveyor length (L) Section 1 Length (L1) Nominal Conveyor Speed (m/min)** Motor Voltage/Frequency Your Choices are: 160, 240, 320, 400, 480, 640, 800, 1040 R, M*, L 0, 90, 180, 270 Non-Antistatic (N) Antistatic (A) 310 mm to 6000 mm (in 5 mm increments) 90 mm to 5770 mm (in 5 mm increments) 6, 9, 12, 15, 18** See Table 9-2 Part Number 3842 999 717 Your selection: ____________ mm _______________ _______________ _______________ ____________ mm ____________ mm ____________ m/mm ________ V ________ Hz

* Mid-mounted motor not available in 160 mm wide conveyors ** Full load conveyor speeds vary depending on motor frequency. See table 9-2.

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 9

Technical data for BS2/M

Nominal belt speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60 Hz Motor electrical specifications = See Table 9-2 = 60 kg = 30 kg = 1400 = 1700 = See Table 9-2

Electrical data for BS2/M

Nom. M/min 6 9 12 15 18 Actual Speed 50 Hz 5.7 9.5 11.5 14.3 19.1 60 Hz 7.0 8.7 11.6 13.9 17.4 HP 50Hz .24 .24 .24 .24 .24 60Hz .28 .28 .28 .28 .28 Full Load Amps @ 208/60 240/60 380/50 415/50 480/60 575/60 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55

Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings.

Table 9-2

Dimensional data for BS2/M

130

Load Capacity with L1 equal or less then 1/3 x L

m 000 m

30

B - 100

B - 75

B + 40

B+2

L=

31

6 0-

60

10

30

L 130

L1 30

Load Capacity with L1 equal or greater then 1/3 x L

00 - 60 mm

30

102

L=

310

ca. 320 mm

30

205

Transverse conveyor line width (B) must match pallet length (LWT) or width (BWT), depending on orientation.

9- 10

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Transverse Conveyors
Model BS2/K

60

Transverse conveyors are most often used to transfer workpiece pallets between parallel conveyor sections. They are also used to construct cycle-independent workstations, or small systems with short conveying lengths. The unit itself is modular and comes with its own midmount or outboard-mounted drive with toothed drive belts. The BS2/K is specially designed to drive KE2/90-O and KE2/180-O curves via an auxiliary output shaft at the return end. The BS2/K is not reversible. Please note that although the BS2/K is available in widths up to 1040 mm, the KE2 curves have a maximum width of 400 mm. In normal operation, the maximum load capacity for transverse conveyors is 60 kg forward. In addition, positioning and control modules can be mounted on transverse conveyors. length, conveyor speed, motor voltage/ frequency, motor mounting and belt version when ordering. Motor voltage and frequency options are described in table 9-3. Transverse conveyors come fully assembled and include all required mounting hardware. NOTE: Transverse conveyor widths in excess of 240 mm are available with either a mid-mounted or outboard-mounted motor as shown. Please contact our applications engineering department for special applications.

Outboard Mounted Motor Orientation

Pallet Flow 180 270 90 0

Motor Position
L

Transverse conveyors are available in any length from 325 mm to 6000 mm in 5 mm increments. Specify conveyor width,

Pallet Flow

Ordering Information for Transverse Conveyors BS2/K

Specify part number, then select from the options below. Width (B) in mm Motor Position Motor Orientation (outboard mount only) Belt Version Transverse Conveyor length (L) Nominal Conveyor Speed (m/min)** Motor Voltage/Frequency
* Mid-mounted motor not available in 160 mm or 240 mm wide conveyors ** Full load conveyor speeds vary depending on motor frequency. See table 9-3.

Your Choices are: 160, 240, 320, 400, 480, 640, 800, 1040 R, M*, L 0, 90, 180, 270 Non-Antistatic (N) Antistatic (A) 325 mm to 6000 mm (in 5 mm increments) 6, 9, 12, 15, 18** See Table 9-3

Part Number 3842 999 715 Your selection: ____________ mm _______________ _______________ _______________ ____________ mm ____________ m/mm ________ V ________ Hz

Note: When using KE2 curves, maximum width is 400 mm

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 11

Technical data for BS2/K

Nominal belt speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60 Hz Motor electrical specifications = See Table 9-3 = 60 kg = N/A = 1400 = 1700 = See Table 9-3

Electrical data for BS2/K

Nom. M/min 6 9 12 15 18
Table 9-3

Actual Speed 50 Hz 6.1 9.1 12.1 15.2 18.2 60 Hz 7.4 8.8 11.1 14.7 18.4

HP 50Hz .24 .24 .24 .24 .24 60Hz .28 .28 .28 .28 .28

Full Load Amps @ 208/60 240/60 380/50 415/50 480/60 575/60 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55

Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings.

Dimensional data for BS2/K

205

130

9
B - 100
L

10 102 ca. 320

130

130

BOSCH

Transverse conveyor width (B) must match pallet length (LWT) or width (BWT), depending on orientation.

B+2 B + 40

9- 12

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Transverse Conveyors
Model BS2/C

60

Flat-top chain transverse conveyors are used to transfer moderate workpiece pallet payloads between parallel conveyor sections. They are also used to construct cycle-independent workstations and are especially suitable for modular system layouts with short conveyor sections at moderate loads. The unit itself is modular and comes with its own drive, return, and pre installed flat-top chain. In normal operation, the maximum load capacity for the BS2/C is 60kg. Reverse operation is not possible Flat-top chains are used as the conveyor media and the unit is delivered with an automatic chain tensioning device. The flat-top chain transverse conveyor is available in lengths from 300mm to 6000mm in 5mm increments. Specify conveyor width, length, conveyor speed, motor voltage/frequency, motor position, and motor orientation when ordering. Motor voltage and frequency are described in the Technical Data table.

Transport media selection is either standard or antistatic flat-top chain. The unit is delivered fully assembled and includes all required mounting hardware. Conveyor widths (B) in excess of 160mm are available with either a mid-mounted or outboard mounted motor as shown. Please contact our applications engineering department for nonstandard length, width, speed, or voltage.

Outboard Mounted Motor Orientation

Pallet Flow 180 270 90 0

Motor Position
L

Pallet Flow

Ordering Information for BS2/C

Specify part number, then select from the options below. Width (B) in mm Motor Position Motor Orientation (outboard mount only) Transverse Conveyor length (L) Nominal Conveyor Speed (m/min)** Motor Voltage/Frequency Flat-top Chain Type Your Choices are: 160, 240, 320, 400, 480, 640, 800, 1040 R, M*, L 0, 90, 180, 270 300 mm to 6000 mm (in 5 mm increments) 6, 9, 12, 15, 18** See Table 9-4 Standard (N) or Antistatic (A)

Part Number 3842 999 917 Your selection: ____________ mm _______________ _______________ ____________ mm ____________ m/mm ________ V ________ Hz _______________

* Mid-mounted motor not available in 160 mm wide transverse conveyors ** Full load conveyor speeds vary depending on motor frequency. See table 9-4.

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 13

Technical Data for BS2/C

Nominal conveyor speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60Hz Motor electrical specifications = See Table 9-4 = 60 kg = NA = 1400 = 1700 = See Table 9-4

Electrical Data for BS2/C

Nom. M/min 6 9 12 15 18
Table 9-4

Actual Speed 50 Hz 5.7 9.5 11.5 14.3 19.1 60 Hz 7.0 8.7 11.6 13.9 17.4 HP .25 .25 .25 .25 .25

Full Load Amps @ 208/60 240/60 380/50 415/50 480/60 575/60 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55

Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings.

Dimensional Data for BS2/C

B-100

B+2

B+40

9
69

10

B-100

B-75

B+2

B+40

61.68

60

170
BOSCH

107

124.4

MOUNTING KIT (100 mm)

MOUNTING KIT (80 mm)

226.5

Transverse conveyor width (B) must match pallet length (LWT) or width (BWT), depending on orientation.

306.4

10

9- 14

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Heavy Duty Flat-Top Chain Transverse Conveyors

Model BS2/C-H

150

Heavy duty flat top chain transverse conveyors utilize a gearmotor and are designed to transfer workpiece pallet payloads between parallel conveyor sections. They are also used to construct cycle-independent workstations and are especially suitable for modular system layouts with short conveyor sections at moderate loads. The unit itself is modular and comes with its own drive, return, and pre installed flat-top chain. In normal operation, the maximum load capacity for the BS2/C-H is 150kg. Reverse operation is not possible. Flat-top chains are used as the conveyor media and the unit is delivered with an automatic chain tensioning device. The flat-top chain transverse conveyor is available in lengths from 300 mm to 6000 mm in 5 mm increments. Specify conveyor width, length, conveyor speed, motor voltage/frequency, motor position, and motor orientation when ordering. Motor voltage and frequency are described in the Technical Data table. NOTE: mid-mount motor position is not an option with heavy duty flat top chain transverse conveyors. Transport media is either standard or antistatic flat-top chain. The unit comes fully assembled and includes all required mounting hardware. Please contact our applications engineering department for nonstandard length, width, speed, or voltage.

Outboard Mounted Motor Orientation

Pallet Flow 180 270 90 0 Pallet Flow

Motor Position
L

Ordering Information for Transverse Conveyor BS2/C-H

Specify part number, then select from the options below.
Drive Unit Width (B) Motor Position Motor Orientation Transverse Conveyor Length (L) Nominal Speed* Motor Voltage/Frequency

Your Choices are:

160, 240, 320, 400, 480, 640, 800, 1040 L or R 0, 90, 180, 270 300mm to 6000mm (in 5mm increments) 9, 12, 15, 18 See Table 9-5

Part Number 3842 999 985 Your selection:

__________mm _____________ __________mm _____________ __________M/min ________ V _______Hz

Flat-top Chain Type

Standard (N) or Antistatic (A)

_______________

* Full load conveyor speeds vary depending on motor frequency. See Table 9-5

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 15

Technical data for BS2/C-H

Nominal conveyor speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60 Hz Motor electrical specifications = = = = = = See Table 9-5 150 kg N/A 1380-1410 1656-1728 See Table 9-5

Electrical data for BS2/C-H

Nom. M/min 9 12 15 18
Table 9-5

Actual Speed 50 Hz 9.2 11.5 14.1 17.2 60 Hz 8.5 10.9 13.8 16.9 208/60 AMPS HP 2.4 1/2 2.4 1/2 2.4 1/2 2.4 1/2

Full Load Amps/HP @ 240/60 AMPS HP 2.4 1/2 2.4 1/2 2.4 1/2 2.4 1/2 380/50 AMPS HP 1.6 3/4 1.6 3/4 1.2 1/2 1.2 1/2 415/50 480/60 575/60 HP AMPS HP AMPS HP AMPS 5/8 1.2 1.7 1.0 5/8 3/4 5/8 5/8 1.2 1.7 1.0 3/4 5/8 1.2 5/8 1.2 1.0 1/2 5/8 1.2 5/8 1.2 1.0 1/2

Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings.

Dimensional data for BS2/C-H

151.5

Drive Width (B)

B+32

B+2

9
B+40 B+181.5

62

140

60
10

60

82.5

70

375

Length (L)
60 170
MOUNTING KIT (100 mm) MOUNTING KIT (80 mm)

160

107

40

140

279

10

9- 16

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Transverse Conveyors
Model BS2/R

200

Roller chain transverse conveyors are used to transfer heavy workpiece pallet payloads between parallel conveyor sections. They are also used to construct cycle-independent workstations and are especially suitable for modular system layouts with short conveyor sections at high loads. The unit itself is modular and comes with its own drive, return, and pre installed roller chain. In normal operation, the maximum load capacity for the BS2/R is 200kg (forward), and 100kg (reverse). The unit uses roller chain as the conveying medium and is delivered with a spring chain tensioning device. Reverse operation is not possible on lengths (L) over 2000mm or when specifying filler blocks (3) or (4) as the roller chain type. NOTE: When reverse operation is specified, a fixed chain tensioner is used instead of the spring tensioner. The roller chain transverse conveyor is available in lengths from 300mm to

6000 mm in 5 mm increments. Specify conveyor width, length, conveyor speed, motor voltage/frequency, motor position, reverse option, and motor orientation when ordering. Motor voltage and frequency are described in the Technical Data table. Transport media selection is one of 4 chain options polyamide rollers, steel rollers, polyamide rollers with filler blocks or steel rollers with filler blocks. The unit comes fully assembled and includes all required mounting hardware. Conveyor widths (B) in excess of 160mm are available with either a mid-mounted or outboard mounted motor as shown. Please contact our applications engineering department for nonstandard length, width, speed, or voltage.

Outboard Mounted Motor Orientation

Pallet Flow 180 270 90 0

Motor Position
L

Pallet Flow

Ordering Information for BS2/R

Specify part number, then select from the options below. Width (B) in mm Motor Position Motor Orientation (outboard mount only) Reverse Operation Transverse Conveyor length (L) Nominal Conveyor Speed (m/min)** Motor Voltage/Frequency Roller Chain Type Your Choices are: 160, 240, 320, 400, 480, 640, 800, 1040 R, M*, L 0, 90, 180, 270 YES=Fixed tensioner NO=Spring tensioner 300 mm to 6000 mm (in 5 mm increments) 6, 9, 12, 15, 18** See Table 9-6 Polyamide Rollers (1) Steel Rollers (2) Polyamide Rollers & Filler Blocks (3) Steel Rollers & Filler Blocks (4) Part Number 3842 999 904 Your selection: ____________ mm _______________ _______________ _______________ ____________ mm ____________ m/mm ________ V ________ Hz

( ) _______________

* Mid-mounted motor not available in 160 mm wide transverse conveyors ** Full load conveyor speeds vary depending on motor frequency. See table 9-6.

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 17

Technical Data for BS2/R

Nominal conveyor speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60Hz Motor electrical specifications = See Table 9-6 = 200 kg = 100 kg with fixed tensioner = 1400 = 1700 = See Table 9-6

Electrical Data for BS2/R

Nom. M/min 6 9 12 15 18
Table 9-6

Actual Speed 50 Hz 5.7 9.5 11.5 14.3 19.1 60 Hz 7.0 8.7 11.6 13.9 17.4 HP .25 .25 .25 .25 .25

Full Load Amps @ 208/60 240/60 380/50 415/50 480/60 575/60 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55 1.6 1.3 0.86 0.72 0.67 0.55

Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings.

Dimensional Data for BS2/R

B-100

B+2

B+40

9
69

10

B-100

B-75

B+2

B+40

MOUNTING KIT (100 mm)

MOUNTING KIT (80 mm)

61.68

60

170
BOSCH

107

Transverse conveyor width (B) must match pallet length (LWT) or width (BWT), depending on orientation.

306.4

124.4

10

9- 18

Bosch Rexroth Corporation

TSplus Assembly Conveyors

8981 500 269 05/09

Transverse Conveyors

Heavy Duty Roller Chain Transverse Conveyor

Model BS2/R-H

450

Heavy duty roller chain transverse conveyors utilize a gearmotor and are designed to transfer workpiece pallet payloads between parallel conveyor sections. They are also used to construct cycle-independent workstations and are especially suitable for modular system layouts with short conveyor sections at high loads. The unit itself is modular and comes with its own drive, return, and pre installed roller chain. In normal operation, the maximum load capacity for the BS2/R-H is 450kg (forward) and 225 kg (reverse). The unit uses roller chain as the conveying medium and is delivered with an automatic chain tensioning device. Reverse operation is not possible on lengths (L) over 2000mm or when specifying filler blocks (3) or (4) as the roller chain type. The roller chain transverse conveyor is available in lengths from 300mm to 6000mm in 5mm increments. Specify conveyor width, length, conveyor speed, motor voltage/frequency, motor position, reverse option, and motor orienta-

Outboard Mounted Motor Orientation

tion when ordering. Motor voltage and frequency are described in the Technical Data table. Transport media selection is one of 4 chain options polyamide rollers, steel rollers, polyamide rollers with filler blocks or steel rollers with filler blocks. NOTE: When reverse operation is specified, a fixed chain tensioner is used instead of the spring tensioner. NOTE: mid-mount motor position is not an option with heavy duty roller chain transverse conveyors. The unit comes fully assembled and includes all required mounting hardware. Please contact our applications engineering department for nonstandard length, width, speed, or voltage.
Pallet Flow 180 270 90 0

Motor Position
L

Pallet Flow

Ordering Information for Transverse Conveyor BS2/R-H

Specify part number, then select from the options below.
Drive Unit Width (B) Motor Position Reverse Operation Motor Orientation Transverse Conveyor Length Nominal Speed* Motor Voltage/Frequency

Your Choices are:

160, 240, 320, 400, 480, 640, 800, 1040 L or R YES=fixed tensioner NO=spring tensioner 0, 90, 180, 270 300 mm to 6000 mm (in 5mm increments) 9, 12, 15, 18 See Table 9-7

Part Number 3842 998 096 Your selection:

__________mm _____________ _____________ __________mm _____________ __________M/min ________ V _______Hz

Roller Chain Type

Polyamide Rollers (1) Steel Rollers (2) Polyamide Rollers & Filler Blocks (3) Steel Rollers & Filler Blocks (4)

( ) _______________

* Full load conveyor speeds vary depending on motor frequency. See Table 9-7

8981 500 269 05/09 Transverse Conveyors

TSplus Assembly Conveyors

Bosch Rexroth Corporation

9- 19

Technical data for BS2/R-H drive

Nominal conveyor speed Load capacity forward Load capacity reverse Motor RPM @ 50 Hz Motor RPM @ 60 Hz Motor electrical specifications = = = = = = See Table 9-7 450 kg 225 kg with fixed tensioner 1380-1410 1656-1728 See Table 9-7

Electrical data for BS2/R-H

415/50 480/60 575/60 208/60 240/60 380/50 AMPS HP AMPS HP AMPS HP AMPS HP AMPS HP AMPS HP 5/8 1.2 9.78 9 9.1 2.4 1.7 1.0 5/8 1/2 1.6 3/4 3/4 2.4 1/2 5/8 5/8 1.2 12.3 12 11.7 2.4 1.7 1.0 1/2 1.6 3/4 3/4 2.4 1/2 5/8 2.4 1.2 1/2 14.9 15 14.7 2.4 5/8 1.2 1.0 1/2 1.2 1/2 1/2 2.4 5/8 1.2 1/2 18.3 18 17.9 2.4 5/8 1.2 1.0 1/2 1.2 1/2 1/2 Note: Electrical Data for reference only. Refer to motor name plate for actual amperage ratings. Table 9-7 50 Hz 60 Hz Nom. M/min Actual Speed Full Load Amps/HP @

Dimensional Data for BS2/R-H

151.5

Drive Width (B)

9
B+40 B+181.5

B+32

B+2

62

140

60 375
10 10

Length (L)
60 170
MOUNTING KIT (100 mm) MOUNTING KIT (80 mm)

160

107

60

82.5

70

40

140

279