DASHBOARD AND CONSOLE
DASHBOARD AND CONSOLE
DASHBOARD REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the driver-side air bag module. (Refer to section T, AIR BAG SYSTEM, DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION.) 3. Remove the passenger-side air bag module. (Refer to section T, AIR BAG SYSTEM, PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION.) 4. Remove the steering wheel. (Refer to section N, MANUAL STEERING, STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.) 5. Remove the installation bolts then lower the assembled steering shaft from the dashboard. (Refer to section N, MANUAL STEERING, STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.) 6. Remove the meter hood. 7. Remove the instrument cluster. 8. Remove the front console. (Refer to FRONT CONSOLE REMOVAL/INSTALLATION.) 9. Remove the glove compartment. 10. Remove the bonnet release cable installation nut. 11. Remove the A-pillar trims. (Refer to TRIM, A-PILLAR TRIM REMOVAL/INSTALLATION.) 12. Disconnect the wires for both the blower unit and the heater unit. (Refer to section U, CONTROL SYSTEM, CLIMATE CONTROL UNIT REMOVAL.) (Refer to section U, CONTROL SYSTEM, CLIMATE CONTROL UNIT INSTALLATION.) 13. Remove the fuse block. 14. Remove in the order indicated in the table. 15. Install in the reverse order of removal. 16. Adjust the wires for both the blower unit and the heater unit. (Refer to section U, CONTROL SYSTEM, CLIMATE CONTROL UNIT ADJUSTMENT.)
7.911.7 {80120, 70104}
7.911.7 {80120, 70104}
7.911.7 {80120, 70104}
Nm {kgfcm, inlbf}
Bolt
Dashboard
S47
DASHBOARD AND CONSOLE
DASHBOARD DISASSEMBLY/ASSEMBLY 1. Disassemble in the order indicated in the table. 2. Assemble in the reverse order of disassembly.
1 2 3
Defroster nozzle Side demister nozzle Center duct
4 5
Duct Dashboard crash pad
S48
DASHBOARD AND CONSOLE
DASHBOARD MEMBER REMOVAL/INSTALLATION 1. Remove the dashboard. (Refer to DASHBOARD REMOVAL/INSTALLATION.) 2. Remove the bolts, then remove the dashboard member.
DASHBOARD MEMBER
1622 {1.62.3, 1216} 1622 {1.62.3, 1216}
FRONT CONSOLE DISASSEMBLY/ASSEMBLY 1. Disassemble in the order indicated in the table. 2. Assemble in the reverse order of disassembly.
BOLT
1622 {1.62.3, 1216} 1622 {1.62.3, 1216}
Nm {kgfm, ftlbf}
3. Install in the reverse order of removal. COLUMN COVER REMOVAL/INSTALLATION 1. Remove the screws, then remove the column cover.
COLUMN COVER
1 2 3 4
SCREW
Screw Front console Boot Set plate
2. Install in the reverse order of removal. FRONT CONSOLE REMOVAL/INSTALLATION 1. Remove the rear console. 2. For manual transaxle vehicle, remove the shift lever knob. 3. Remove the screws, then remove the front console. Caution D In order to prevent noise caused by interference with the dashboard, install the screws to the rear of the front console before installing the front of the front console.
FRONT CONSOLE
REAR CONSOLE REMOVAL/INSTALLATION 1. Remove the screws. 2. Pull the rear console upward, then remove it.
REAR CONSOLE
SCREW
SCREW
3. Install in the reverse order of removal. 4. Install in the reverse order of removal.
S49
DASHBOARD AND CONSOLE
REAR CONSOLE DISASSEMBLY/ASSEMBLY 1. Disassemble in the order indicated in the table. 2. Assemble in the reverse order of disassembly. METER HOOD REMOVAL/INSTALLATION 1. Remove the screws. 2. Pull the meter hood toward you, then disengage clips A and pins B.
A B SCREW A B A A
B A
A CLIP
B PIN A
3. Disconnect the connectors, then remove the meter hood. 4. Install in the reverse order of removal.
1 2 3 4 5 6 7
Screw Console lid outer Console lid inner Rear console Console lid lock Console lid hinge Console lid bracket
GLOVE COMPARTMENT REMOVAL/INSTALLATION 1. Open the glove compartment and bend the sides inward to disengage the pins. 2. Pull the glove compartment downward, then disengage clips A.
PIN PIN
A CLIP A GLOVE COMPARTMENT
3. Install in the reverse order of removal.
S50
