Scribd
Upload
144 views4 pages

Contemporary Clock: Project 12213EZ

This document provides instructions for making a contemporary oak clock that is suitable for beginner woodworkers. The clock features a simple design that utilizes a battery-powered quartz movement. The instructions outline cutting the wood pieces, assembling the frame with miter joints, attaching the front and back panels, and installing the pre-assembled clock movement. The overall construction requires only basic woodworking skills and joinery.

Uploaded by

BSulli
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
144 views4 pages

Contemporary Clock: Project 12213EZ

This document provides instructions for making a contemporary oak clock that is suitable for beginner woodworkers. The clock features a simple design that utilizes a battery-powered quartz movement. The instructions outline cutting the wood pieces, assembling the frame with miter joints, attaching the front and back panels, and installing the pre-assembled clock movement. The overall construction requires only basic woodworking skills and joinery.

Uploaded by

BSulli
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Project 12213EZ:

Contemporary Clock

There seems to be a surprisingly large number of woodworkers who feel that to do


any kind of clockmaking requires exceptional skills and years of practice. No
doubt that’s true for some clock designs, but certainly not for all of them. Many
kinds of clocks are remarkably easy to make, especially since the advent of battery
powered quartz movements.
This attractive contemporary clock falls well within the skill level of even a begin-
ning woodworker. Oak solid stock is used throughout, and the joinery is basic. If
you’ve never built a clock before, and would like to try, this is a good one to cut
your teeth on.
Contemporary Clock Complete
Schematic
Contemporary Clock
Step-by-Step Instruc-
tions
1. Obtain the battery operated quartz
pendulum movement, hands, and
dashes at a clockmaker’s supply store.
2. Select 5/8" thick stock with a pleasing
appearance to make the front and back
of the clock.
3. Cut both parts to a width of 10-3/4"
and a length of 18-1/4".
4. Check to make sure that the cuts are
square.
5. Lay out the location of the openings in each part.
6. Drill a 3/8" hole in the waste stock.
7. Use this hole as a starting point to use the saber saw to cut out the openings.
8. Determine the measurements of the hole in the front part that accommodate
the movement shaft.
9. Lay out and drill that hole.
10. Select 3/4" thick stock to make the frame.
11. Cut the top and bottom each to 2-3/4" x 10-3/4".
12. Cut the sides each to the same width, but make them both 10-3/4" long.
13. Set the table or radial arm sawblade to 45 degrees to begin making the
miters. NOTE: Since the angle must be exact, don’t rely on the crude
gauges that most saws have. Instead use a draftsman’s 45-degree tri-
angle to check the angle.
14. Cut the miters.
15. Apply a coat of glue to the miters to begin assembling the frame.
16. Let that coat soak in to the stock.
17. Apply another coat of glue to the miters.
18. Use corner clamps to secure each joint (see photo).
19. Set the frame aside to dry overnight.
20. Apply glue to the mating surfaces where the front and back join the frame.
21. Use C-clamps (see photo) with clamp pads to protect the clock case to hold
the pieces together while the glue dries.
22. Use a router with a 1/2" rounding-over bit to round over all edges.
23. Give all surfaces a thorough sanding.
24. Apply a coat of penetrating oil to finish.
25. Assemble the movement.
26. Assemble the case as shown. NOTE: The opening in the back makes for
easy access to the movement.
27. Add the “AA” alkaline battery that supplies the power to complete.

These plans were originally published in Volume 7, Issue 1 of The Woodworker’s


Journal (Jan./Feb. 1983, pages 46-47).

You might also like