TG
Pull Handles
The Shape of Quality
TG Pull Handles
Our Quality Claim
What it takes to be a DORMA pull handle
Pull handles from DORMA Door Furniture epitomise the claim to quality underlying the DORMA brand. In critically scrutinising every detail, we deliver products offering the same distinctive quality features whatever their shape, size or customisation. So you can be sure of an attractive design and a highgrade surface nish with negligible hairlines joint. We provide a uniform grain virtually devoid of sink marks and irregularities and that also goes for the more inaccessible locations such as curve inside radii, 90-degree mitre cuts or the transition points from pull handle to xing spacer/support. You will surely be impressed by the high standard of workmanship and the care we apply to every aspect. Our strictly regulated quality management system ensures maximum functional and maximum visual appeal. DORMA has dened its own strict requirements against which we constantly check the quality of our pull handles. We verify compliance with demanding technical parameters such as pull-off force and continuous-mode compressive and tensile loading. Plus, the machining quality and appearance are constantly checked to ensure compliance with our and your high demands. Only once the product has satised our exacting quality standards is it given the seal of approval as a DORMA pull handle. DORMA pull handles offer safe absorption of compression and tension once properly installed with our superior xing systems. These enable fast and easy installation on virtually any door. In short, with DORMA pull handles you can be condent that you have chosen a true quality product.
DORMA now thats quality Great workmanship Great resilience Great appearance
Setting the standards: Fewer xing sets plus divine proportionality
1. Fewer xing sets In order to facilitate matching the xing materials to the door, we have reduced the number of xing sets from 24 to 14. These sets can be widely used, ensure high stability and are easy and quick to apply. To make selection even easier, the xing sets have been divided into three categories: Timber doors, narrow-stile doors and toughened glass doors. So now it is even simpler to choose which xing set is most suited to your door. See page 22/23. 2. The golden ratio We use one of natures formulae, the golden ratio, to dene the relationship between xing spacer/support centres and overall length. For further informa tion, turn to pages 4/5 in this brochure.
min. 25 mm
Please note: In order to minimise the nip and graze hazard associated with doors, we recommend that you install your pull handles to allow a sufciently large clearance with respect to the closing edge of the frame particularly on the pull side of narrow-stile doors. As in the case of
lever handles, there needs to be a minimum clearance of 25 mm between pull handle and frame edge. We particularly recommend our model TG 9377 with angled xing spacers. This keeps the hand safely away from the frame as the door is opened and closed.
Quality feature I High precision in pull handles with xing spacers. The susceptible transition point between the pull handle and the xing spacer/support needs to feature a consistent, high-quality grain, and the radii of both the pull handle and the spacer also have to t perfectly to meet DORMAs demanding standards.
Quality feature II Mitred joints place enormous requirements on welding and grinding accuracy. There can be no defects in the joint area. The weld has to be perfect in order to render it properly invisible by grinding. Because the inside angle is very hard to access, the grinder has to work with the utmost precision. And the same goes for the outside angle where it is important to enhance the clarity of the contours.
Quality feature III The ends of our curved pull handles are likewise machined with the utmost care. High-quality bending jigs ensure the avoidance of dents and sink marks. As in the case of the mitred joints, maximum precision has to be applied to both the inside and outside radii in order to produce a uniformly smooth, high-quality surface.
TG Pull Handles
Design Credentials
Unique appeal.
We combine outstanding workmanship with character forming shapeliness either in the form of our own creations or designed in close cooperation with architects and designers. The DORMA approach is to constantly take a fresh look at our products and to further develop them in the very best way we can. With pull handles in which the length between the xing spacer centres (DORMA dimension Li) is not identical with the overall length (DORMA dimension La), the question inevitably arises as to what the best ratio is between these two variables. Or, to put it another way, how big should the overhang be? And the answer is invariably to apply a certain ratio encountered not only in nature but also in art and architecture. A natural rule of aesthetic elegance and harmony, It offers ideal proportionality and goes by the name of the golden ratio (aka golden section lat. sectio aurea). In architecture, there are many references to the golden ratio for example in relation to the Great Pyramid of Cheops, the Parthenon Temple on the Acropolis, Florence Cathedral or NotreDame Cathedral in Paris. However, deliberate use of this proportionality is only rarely claimed or proven.
The rst exact description of the golden ratio was provided by Euclid (around 300 B.C.). During analysis of Euclids work, the Franciscan monk Luca Pacioli di Borgo San Sepolcro (1445 1514) and later the German mathematician and
astronomer Johannes Kepler (1571 1630) picked up on this divine proportionality between two lengths. The golden ratio rule reads as follows: a is to b as a+b is to a.
DORMA Design Formel nach der gttlichen Teilung:
La = Li x 1.6
b a Li La a b
La
According to the golden ratio rule, the ideal proportion between a and b is almost precisely 1.6:1 and is usually designated with the Greek letter (phi). We translate this golden ratio for our pull handles using the simple formula: La = Li x 1.6. If, for example, the xing spacer/support centres Li measure 350 mm, the total length La adopted is 560 mm (350 mm x 1.6). We use the golden ratio for our pull handle models TG 9377 (with angled spacers) and TG 9387 (with straight spacers).
Naturally, we will continue to supply DORMA pull handles in accordance with your personal requirements. However, if your customers should need help in deciding and place particular value on aesthetic appearance, why not tell them too of the golden ratio? Because DORMA products are always designed with elegance in mind, all we need for your pull handle enquiries or orders is the spacer centres dimension Li. Unless you have specic requirements for the full length La, we will simply supply you the pull handle in accordance with the golden ratio.
TG 9387-32
Materials and surface nishes Stainless steel, S/S satin brushed mirror nish 240 grain
Li
TG Pull Handles
Product Lines
Stylish in diversity.
DORMA pull handles are a successful synthesis of reliable function and aesthetic appeal. In order to meet each individual requirement, we have divided our pull handle range into four product lines, each of which expresses its own unique character: TG Classic, TG Avantgarde, TG Vario and Impact Protection Guards a diverse portfolio that further underlines DORMA competency, while making choosing the right solution easier than ever.
TG Classic
Pages 08 15
TG Avantgarde
Pages 16 17
TG Vario
Pages 18 19
Impact Protection Guards
Pages 20 21
Va r i o p r
od
working days
uction
TG
TG Pull Handles
TG Classic Support Roses
Pull handle series with straight and angled xing spacers.
With our new pull handle series TG 9377 (angled spacers) and TG 9387 (straight spacers), we are able to satisfy the preference in architecture these days for supports of a more slender diameter than that of the pull bar. The result is particularly pleasing to the eye, with no adverse effect on the stability of the pull handle assembly. The ratio between the diameters of the pull bar (G) and the spacer (S) is identical in both series.
X20 | 18
G | S mm S
X25 | 18
X32 | 26
X40 | 32
G Pull handle with straight spacers
TG 9387-20 S
TG 9387-25
TG 9387-32
TG 9387-40
G Pull handle with angled spacers
TG 9377-25
TG 9377-32
TG 9377-40
Support roses of stainless steel for better force distribution and improved door surface protection.
We use 2 mm support roses as standard for pull handle xing sets GZ 203 (bolt through-xing with screw-on cap opposite) and GZ 215 (pull handles back-to-back). This ensures that the operating forces are better distributed and the glass is more effectively protected. The diameter of the support rose is aligned to the diameter of the pull handle or spacer. Because of their attractive design, our support roses are also frequently used in conjunction with other DORMA xing arrangements. We offer roses in four different diameters (37, 40, 44 and 50 mm) and two material thicknesses (2 and 8 mm). If you would like to take advantage of this alternative, simply tell us the xing set/method you intend to use and the desired thickness of your support rose.
Support roses of 2 mm and 8 mm material thickness
XR
Material thickness
2 mm
Xr
GZ 537 R mm r mm Thickness in mm For pull handle mm 37 6,2 2 20 GZ 540 40 6,2 2 25 GZ 544 44 8,2 2 32 GZ 550 50 8,2 2 40
XR
Material thickness
8 mm
Xr
GZ 537 R mm r mm Thickness in mm For pull handle mm 37 6,2 8 20 GZ 540 40 6,2 8 25 GZ 544 44 8,2 8 32 GZ 550 50 8,2 8 40
TG Pull Handles
TG Classic
Pull handles with angled xing spacers.
The TG 9377 is a pull handle with angled xing spacers in elegant stainless steel. The ratio between its spacer centres (Li) and overall length (La) is in keeping with the golden ratio rule. Below are some impressive examples of what we can do. And of course we will also be glad to supply pull handles in accordance with your individual dimensions.
min. 25 mm
TG 9377
XS
La = Li x 1,6
b a Li La a b
La Li
La Li
XS
XG
XG
G mm 25 32 32 40 x 2,0 40 x 3,0 S mm 18 26 26 32 32 H mm 75 85 85 100 100 A mm 31 38 67 46 46 B mm 60 71 104 85 85 Sttze 60 60 45 60 60 3rd spacer required 1,200 1,600 1,600 2,100 2,400 from Li mm
La = Li x 1.6 Other length ratios and spacer centres on request
B A
If ordering a 32 mm 32 handle, please indicate whether you want the spacer angle to be 45 or 60
Recommended arrangement for a narrow-stile door
B A H
Li = 350 La = 560
Li = 500 La = 800
Li = 1,000 La = 1,600
10
The proportions indicated are in keeping with golden ratio
Pull handle with straight xing spacers.
The TG 9387 in stainless steel further extends our range of pull handles with straight xing spacers. Here once more, we stick to the golden ratio rule in determining the proportionality between the spacer centres (Li) and the overall length (La). Again we recommend the formula La = Li x 1.6. The examples shown below illustrate what you can expect. Needless to say, the TG 9387 is also available in customised lengths and dimensions. It can be combined with support roses GZ 537 - GZ 550 if required.
TG 9387
La = Li x 1,6
b a Li La a b
XS
XG
G mm 20 25 32 40 x 2,0 40 x 3,0 S mm 18 18 26 32 32 H mm 65 75 85 100 100 3rd spacer required 1,200 1,500 1,900 2,600 2,900 from Li mm
La Li
La = Li x 1.6 Other length ratios and spacer centres on request
H
Recommendation for timber doors
Li = 350 La = 560
Li = 500 La = 800
Li = 1,000 La = 1,600
Support rose optional
The proportions shown are examples of the golden ratio
11
TG Pull Handles
TG Classic
TG Classic
Designed and developed for tough applications in heavily used buildings, the Classic range with its resilience and quality is ideally suited for equipping schools and local authority establishments, for example. If you have your own ideas of what your pull handles should look like, we will be glad to turn them into reality. We will prepare a production drawing in accordance with your sketch and, once you have approved our design and placed your order, we will manufacture your pull handle based on our quotation.
TG 9359
TG 9316
350
90
350
90
175
d
90 single-piece handle, S/S, ALU
Mitred handle with fixing spacers, S/S
Xmm
Rmm Bmm Hmm
25 40 158 75
32* 45 156 85
40 60 156 100
XD mm
d mm Hmm Amm
32 32 85 20
40 40 100 25
*Alu = 30 mm
Other pull handle heights (dimension H) on request
12
R1
350
B
R
H
Semi-circular single-piece handle, S/S, ALU mm 25 R mm 40 R1 mm 100 Bmm 140 H mm 75 L mm 200 30 45 150 195 85 300 32* 45 175 220 85 350 40 60 175 235 100 350
Semi-circular handle with fixing spacers, S/S D mm d mm R mm B mm H mm M mm 30 26 175 195 85 20 40 32 175 205 100 25
TG 9304
*Alu = 30 mm
TG 9306
TG 9356
TG 9313
TG 9355
TG 9335
200 100
R1
00
85
B
R
l 26
l 30
Swept single-piece cantilever handle, S/S, ALU Xmm 25 32* 40 Rmm 40 45 60 Bmm 100 140 150 Hmm 75 85 100 L mm from from from 210 210 250 *Alu = 30 mm
Circular handle, S/S TG 9313 mm Rmm 30 100
Straight single-piece handle, S/S, ALU Xmm 20 25 32* Rmm 30 40 45 Hmm 65 75 85 L mm from from from 150 210 210 *Alu = 30 mm
Straight mitred handle, S/S 40 60 100 from 250
Xmm
Hmm L mm
25 75
32 85
40 100
> 210 from L mm* 1,500
> 200 > 200 1,900 2,600
Standard length 350mm * = additional fixing point
Other pull handle heights (dimension H) on request
13
TG Pull Handles
TG Classic
TG 9317
TG 9318
5 R4
90
R 15
La Li
0
450
Li
Mitred V cantilever handle, S/S D mm d mm B mm H mm Li mm up to M mm A mm 32 32 215 85 700 2.200 430 20 40 40 225 100 700 2.200 450 25 Single-piece C cantilever handle, S/S, ALU mm 30 B mm 195 H mm 85 Li mm 700 up to 2.000 Additional fixing spacers from Li = 1,200 mm
Additional fixing spacers from La = 2,500 mm
14
Pull handles with xing brackets.
TG 9391
H 35
TG 9394
H 35
Stainless steel pull handles are often offered as modular systems with the tube and spacers being separately supplied. These kits can then be tailored to the door on site by cutting the stainless steel tubes to length and xing the support brackets in place. However, this can result in dimensional and installation inaccuracies as well as causing problems if the support centres are too large to provide the necessary long-term resilience. The use of unsuitable saws when cutting to length can also adversely affect the corrosion behaviour of pull handles. At DORMA, we make sure that our customers are not confronted by such problems. As with our TG Vario system (see also pages 18/19), we supply the two models TG 9391 with angled and TG 9394 with straight supports as ready-made pull handles. That way you can be sure that the hardware ordered on the basis of your length specications will readily withstand the wear and tear of continuous usage.
15
15
Li
La
Li
32/40
30
TG 9391 D mm H mm 32 40 65 80
32/40
TG 9394 D mm H mm 32 40 65 80
La
Fixing materials for the TG 9391 and TG 9394 pull handles will need to be provided by others.
15
TG Pull Handles
TG Avantgarde
30
15
45 93
30
Design Award Winner 2002 TG 9830 TG 9830 S/S
16
350
TG Avantgarde
Designed to create a prestigious and progressive appearance as part of an advanced architectural concept, these pull handles always leave the right visual impression, making them ideal for banks, insurance company buildings and similar. They certainly represent a step forward in creativity for contemporary entrance designs so it will come as no surprise that Avantgarde pull handles from DORMA have also garnered Germanys coveted iF design award.
TG 9910
TG 9911
TG 9915
80
30
40
40 370 350
390
350
30
20
85
40
40
85
20
20
TG 9910
S/S
TG 9911
S/S
TG 9915
350
525
S/S
17
TG Pull Handles
TG Vario
TG Vario individual lengths from the same stock.
Until now, pull handles could usually only be quickly supplied in standard lengths of 350 mm. Customisation with special lengths could take weeks. But we pledge fast delivery of almost any length. DORMA pull handles, even when manufactured precisely to specication, are delivered on time. And you have the benet of no on-site adaptation work. Product liability for deciency-free supply therefore remains with DORMA as the hardware manufacturer. Youll be hard pushed to nd a faster, technically more reliable and more convenient solution - so make the most of this innovative service.
X
X You specify the precise centres dimension and we ensure on-schedule production with shipment in ve working days.
Va r i o p r
The DORMA pledge: We offer a production time of generally ve working days following order receipt and clarication of all technical details for our ve stainless steel models TG 9335, TG 9355, TG 9356, TG 9377 and TG 9387, subject to manufacture and delivery in standard commercial volumes.
od
working days
uction
TG 9335
L 210 l 32 85
18
TG
All the benets at a glance: No pull handle adaptation on site saving you time and money. No off-cuts as DORMA pull handles are also supplied precisely fabricated to customised lengths saving you material and cost. The pull handles are shipped to order, eliminating storage expenses.
Highly resilient pull handle performance with manufacture from a single stock length. Minimal corrosion susceptibility as only stainless steel is cut and machined on the saw and grinding equipment used for the TG Vario range something that is almost impossible to guarantee on site.
DORMAs TG Vario pull handles can be combined with all DORMA xing sets. Identical appearance of all pull handles within a building.
Support roses optional
TG 9355
TG 9356
TG 9377
TG 9387
X26
L 210
L 210
La
Li
La
32
La Li
XS
85 85
140 32
85
X26
X26 X32
X32
85
32
XG
Li
X26
X32
71
26
19
TG Pull Handles
Impact Protection Guards
DORMA impact protection guards in stainless steel.
In many buildings, there will be walls and doors that tend to suffer from heavy, unintended contact, causing damage to their surface. In hospitals, senior residences and care homes, for example, beds may frequently impact against walls or doors, either because they have been parked in corridors or are used for the transportation of patients. The consequences of even light contact are unsightly surfaces with chips and numerous other forms of damage at the height of the contact point. And that can mean expensive repairs. Moreover, the same damage is likely to be inicted again after just a short period. The guards can be xed using our accessories to virtually any door or wall to provide sturdy protection.
Wherever walls and doors are exposed to such attrition, we recommend the use of DORMA impact protection guards. Because these components are there to absorb impact and are therefore themselves exposed to contact, we prepare their surfaces with our proven basic-grain nish.
Simply send your enquiries or orders under the heading impact Protection Guards to your DORMA contact or our main address.
20
Curved
L R H H
Mitred
L
Fixing spacers
La Li H
mm R mm H standard mm H min. mm
20 30 65 60
25 40 75 60
32 45 85 85
mm H standard mm H min. mm
25 75 55
32 85 60
G mm S mm H mm
20 18 65
25 18 75
32 26 85
The ends of the impact protection guards can be curved, mitred or provided with xing spacers.
21
TG Pull Handles
Fixing Materials
The right pull handle xing solution for every door type Selecting the appropriate pull handle xings has now become even easier. Simply select your door type from photos 1 3 and make a note of the number (e.g. 2 for narrow-stile doors). Each xing set is likewise indicated by the numbers 1, 2 or 3. This indicates the door type for which each set of xings is best suited. For
your narrow-stile door, therefore, you can use all the xing arrangements with the number 2 in the corner.
Timber door
Fixing sets for timber, narrow-stile and toughened glass doors.
1 2
Bohrung l 10, M8, l 30-l 40 l 8, M6, l 20-l 25
GZ 202*
Fixing to narrow-stile and timber doors Single-sided, through-bolt xing with screw-on cap opposite. Door thickness 35-100 mm. When placing an order, please indicate colour, pull handle and door thickness.
1 2
GZ 224*
Fixing to narrow-stile and timber doors Single-sided, concealed with clip-on rose. Minimum door thickness 35 mm. Suitable for straight pull handles only. Fixing screws not supplied When placing an order, please indicate colour and pull handle .
Bohrung l 12, M8, l 30-l 40 l 10, M6, l 20-l 25
GZ 203*
Fixing to glass doors Single-sided, through-bolt xing with screw-on cap opposite. Glass thickness 8-15 mm. When placing an order, please indicate colour, pull handle and the glass thickness.
1 2
Gewinde M8, l 30-l 40 M6, l 20-l 25
GZ 234*
Fixing to narrow-stile and timber doors Single-sided, concealed Bolting depth 20 mm. When placing an order, please indicate colour and pull handle .
1 2
Bohrung l 10, M8, l 30-l 40 l 8, M6, l 20-l 25
GZ 214*
Fixing to narrow-stile and timber doors. Back-to-back, concealed. Door thickness 35-100 mm. When placing an order, please indicate colour, pull handle and door thickness.
Bohrung l 10
GZ 274*
Fixing to timber doors Single-sided, concealed Minimum door thickness 40 mm. When placing an order, please indicate colour and pull handle .
Bohrung l 12, M8, l 30-l 40 l 10, M6, l 20-l 25
GZ 215*
Fixing to glass doors Back-to-back, concealed. Glass thickness 8-15mm. When placing an order, please indicate colour, pull handle and the glass thickness.
1 2
Bohrung l 6,5
GZ 284*
Fixing to narrow-stile and timber doors Single-sided, concealed. When placing an order, please indicate pull handle and prole thickness < 39 mm, 40 54 mm or > 54 mm.
1 2
Bohrung l 10, M8, l 30-l 40 l 8, M6, l 20-l 25
GZ 216*
Fixing to narrow-stile and timber doors Single-sided, through-bolt xing. Door thickness 35-80 mm. When placing an order, please indicate pull handle and door thickness. .
All xing sets GZ 2xx and GZ 3xx are unsuitable for pull handles TG 9391 and TG 9394. Fixings for these pull handles will need to be provided by others.
* * Please note the reduced hole diameter.
Fixing set GZ 202 to GZ 284 cannot be combined with pull handle TG 9377 (for TG 9377, see page 23).
22
Narrow-stile door
Toughened glass door
Special xing sets for the TG 9377.
1 2
Bohrung l 8, M6
GZ 302
Fixing to narrow-stile and timber doors, Single-sided, bolt through xing with screw-on cap opposite. Door thickness 35-100 mm. When placing an order, please indicate colour, pull handle and door thickness.
Bohrung l 10
GZ 374
Fixing to timber doors Single-sided, concealed Minimum door thickness 40 mm. When placing an order, please indicate colour, pull handle .
1 2
Bohrung l 8, M6
GZ 314
Fixing to narrow-stile and timber doors, Back-to-back, concealed Door thickness 35-100 mm. When placing an order, please indicate colour, pull handle and door thickness.
1 2
Bohrung l 6,5
GZ 384
Fixing to narrow-stile and timber doors, Single-sided, concealed. When placing an order, please indicate pull handle and prole thickness < 39 mm, 40 54 mm or > 54 mm.
1 2
Gewinde M6
GZ 334
Fixing to narrow-stile and timber doors, Single-sided, concealed Bolting depth 20 mm. When placing an order, please indicate colour, pull handle . All xing sets GZ 2xx and GZ 3xx are unsuitable for pull handles TG 9391 and TG 9394. Fixings for these pull handles will need to be provided by others.
Support roses
GZ 537 Rose mm Hole mm Thickness mm For pull handles mm 37 6.2 2 20 GZ 540 40 6.2 2 25 GZ 544 44 8.2 2 32 GZ 550 50 8.2 2 40
Provided as standard with xing sets GZ 203 and GZ 215 for toughened glass doors. GZ 537 Rose mm Hole mm Thickness mm For pull handles mm See support roses, page 9
23
GZ 540 40 6.2 8 25
GZ 544 44 8.2 8 32
GZ 550 50 8.2 8 40
37 6.2 8 20
Door Control
Automatic
WN 053 688 51532, GB, X, XX, 03/09
Glass Fittings and Accessories
DORMA GmbH + Co. KG Postfach 4009 D-58247 Ennepetal DORMA Platz 1 D-58256 Ennepetal Tel. +49 2333 793-0 Fax +49 2333 793-495 www.dorma.de DORMA Beschlagtechnik GmbH Donnenberger Strae 2 D-42553 Velbert Tel. +49 2053 4950 Fax +49 2053 495100 UK/Ireland DORMA UK Ltd. Wilbury Way Hitchin GB-Hertfordshire SG4 0AB Great Britain Tel. +44 1462 477600 Fax +44 1462 477601
Security/Time and Access (STA)
Movable Walls
