Incorrect or out of phase engine timing can result in damage to the valves.
The Tool Connection cannot be held responsible for any damage caused
by using these tools in anyway.
3388
Safety Precautions Please read
Disconnect the battery earth leads
(check radio code is available)
Remove spark or glow plugs to make
the engine turn easier
Do not use cleaning fluids on belts,
sprockets or rollers
Always make a note of the route of the
auxiliary drive belt before removal
Turn the engine in the normal direction
(clockwise unless stated otherwise)
Do not turn the camshaft, crankshaft or
diesel injection pump once the timing
chain has been removed (unless
specifically stated)
Do not use the timing chain to lock the
engine when slackening or tightening
crankshaft pulley bolts
Do not turn the crankshaft or camshaft
when the timing belt/chain has been
removed
Mark the direction of the chain before
removing
It is always recommended to turn the
engine slowly, by hand and to re-check
the camshaft and crankshaft timing
positions.
Crankshafts and Camshafts may only be
turned with the chain drive mechanism
fully installed.
Do not turn crankshaft via camshaft or
other gears
Part No. 4076
Engine Timing Tools
Renault dci
Check the diesel injection pump timing
after replacing the chain
Observe all tightening torques
Always refer to the vehicle
manufacturers service manual or a
suitable proprietary instruction book
Incorrect or out of phase engine timing
can result in damage to the valves
It is always recommended to turn the
engine slowly, by hand, and to re-check
the camshaft and crankshaft timing
positions
Guarantee
If this product fails through faulty materials or workmanship, contact
our service department direct on: +44 (0) 1926 818186. Normal wear
& tear are excluded as are consumable items & abuse.
www.lasertools.co.uk
www.lasertools.co.uk
Plan Layout
Instruction (DE)
Spannwerkzeug
Fur der korrekten Spannung ermglicht,
zum riemens-Grtel angewandt zu
werden.
Kurbelwellen-Fixierdorn
Es gibt vier andere Stcke, die in diesem
eingeschlossen werden, das gesetzt wird.
Wie mit der Nockenwelle-Timing-Nadel
werden sie durch den Motorblock
hineingesteckt und gebraucht, die
Kurbelwelle aufzustellen, um die korrekte
riemen des ersten Zylinders zu erreichen.
Es ist wichtig, da diese Stcke benutzt
werden, um die riemens zu setzen, aber
wird nicht benutzt werden, um das
Schwungrad abzuschlieen.
I
H/I
D
A
G
E
Ref
Code
C037
C067
Oem Code
Description
MOT 1489
Crankshaft Timing Pin
C099
MOT 1054
Flywheel Locking Pin
C101
MOT 1430
Camshaft Timing Pin
C281
MOT 1543
Tension Pre-Setting Tool
C182
MOT 1538
Hi Pressure Fuel Pump Pulley Locking Pin
C179
MOT 1536
Flywheel Setting Pin
M6 X 30mm Tensioning Screw
C180
MOT 1537
Camshaft Locking Tool - Exhaust
C181
MOT 1534
Camshaft Locking Tool Inlet
www.lasertools.co.uk
www.eldontools.
E
Die Auslass-Nockenwelle mit dem Halter F
arretieren und mit der Schraube G sichern.
Ist das Werkzeug nicht exakt zu montieren,
drehen Sie die Kurbelwelle um 180 in
Drehrichtung. Lsen Sie die Befestigung
der Riemenscheibe, whrend der
Installation drfen die Schrauben nicht am
Ende der Langlcher anliegen.
Der Hebelarm wird am Spanner anliegen.
Die Oberseite des Armes fluchtet mit der
NW-Arretierung, wenn der Spanner gegen
den Urzeigersinn gedreht wird. Verwenden
Sie einen 6 mm Inbus.
D
Montieren Sie die Arretierung H der
Einlass-Nockenwelle an den senkrechten
Abflachungen der Welle.
www.lasertools.co.uk
8
Instruction (ES)
Applications
Tornillo de tensado
The application list for this product has been compiled cross referencing the OEM Tool
Code with the Component Code.
Que permite aplicar la tensin correcta a la
correa de distribucin.
In most cases the tools are specific to this type of engine and are necessary for Cam belt or
chain maintenance.
If the engine has been identified as an interference engine valve to piston damage will
occur if the engine is run with a broken Cam belt.
Chavetas de reglaje del cigeal
Hay cuatro pedazos diferentes incluidos en
esto puesto. Como con el rbol de levas
que cronometra el alfiler, ellos se insertan
a travs del bloque motor y posicionaban
el cigeal para lograr la posicin de la
oportunidad correcta del primer cilindro.
Es importante que estos pedazos se usan
para poner la posicin de la oportunidad,
pero no ser usado para cerrar con llave el
volante.
A compression check of all cylinders should be performed before removing the cylinder
head.
Always consult a suitable work shop manual before attempting to change the Cam belt or
Chain.
Autodata
Our applications data is supplied by Autodata and we are able to supply this data to you in
a PDF format.
A
Herramienta de tensado
Para permitir aplicar la pre-tensin
correcta a la correa de distribucin. Esta
herramienta tiene 3 el tubo de proteccin
intercambiables y una espacio para
satisfacer la variedad de tensor usada.
Instale el herramienta de bloques de rbol
de levas de escape F y contenga lugar que
usa un tornillo de seguridad G.
Si la herramienta no puede encajarse
correctamente, ruede el cigeal uno se
vuelve en el sentido de las agujas del reloj.
Modere los broches del diente, pero
verifique eso durante instalacin que los
broches no se posicionan al final de las
hendeduras. El brazo de la palanca lega el
contacto de cierre con el tensor. Como un
registro visual la cima del brazo alinear
con el til fijador del rbol de levas cuando
el tensor se ha vuelto anti-en el sentido de
las agujas del reloj aunque siendo de
tensor que usa un llave 6 mm.
If this is a master kit then all vehicles are included.
The data is the copyright of Tool Connection and should not be reproduced.
If the application data is extensive we have included a CD with the application list in .pdf
format.
Languages
Instale el herramienta de bloques de rbol
de levas de admisin encima de los pisos
verticales en el rbol de levas.
www.lasertools.co.uk
7
If this is a specific kit for a group of engine codes the application list has been supplied
showing the main vehicles this kit is designed for and does not list every model each pin
fits.
We have also included where possible translations for the instructions in the following
languages:
French
Spanish
German
Portuguese
Italian
Dutch
The use of these engine timing tools is purely down to the users discretion and
Tool Connection cannot be held responsible for any damage caused what so ever.
ALWAYS USE A REPUTABLE WORKSHOP MANUAL
www.lasertools.co.uk
3
Instruction (GB)
Instruction (FR)
Tensioning Adjustment Screw
To enable the correct tension to be applied
to the timing belt.
Crankshaft Timing Pins
Permet le calage du vilebrequin au PMH.
Outil de calage moteur de PMH, ne pas
utiliser comme outil de blocage moteur.
G
Outils de tendeur
It is important that these pieces are used
to set the timing position, but are not to
be used to lock the flywheel.
Tensioning Tools
To enable the correct pre-tension to be
applied to the timing belt, this tool has 4
interchangeable covers and a spacing
washer to suit the variety of tensioners
used.
Install the exhaust camshaft locking tool
and hold in place using the setscrew
Slacken the sprocket fasteners, but check
that during installation the fasteners are
not positioned at the end of the slots.
The lever arm will make contact with the
tensioner. As a visual register the top of
the arm will align with the camshaft
locking tool when the tensioner is turned
anti-clockwise whilst being tensioned
using a 6 mm. hex. key.
Install the inlet camshaft locking tool
over the vertical flats on the camshaft.
www.lasertools.co.uk
4
Pour lapplication de la tension sur
la courroie de distribution
Piges de calage des
volants moteurs:
There are two different pieces included in
this set. As with the camshaft timing pin,
they are inserted through the engine block
and used to position the crankshaft to
achieve the correct timing position of the
first cylinder.
If the tool cannot be fitted correctly, rotate
the crankshaft one turn clockwise.
Boulon de tendeur
Permettre la pre - tension correcte dtre
appliqu la ceinture du rglage. Cet outil
a trois coupes interchangeables et une
rondelle de lespacement pour convenir la
varit de tensioner utilis
Monter l outil de calage d arbres cames,
chappement, F et le tenir fixe utilisant la
vis de blocage G.
Si ce n est pas possible de monter l outil
correctement, tourner le vilebrequin un
tour dans le sens des aiguilles d une
montre. Lacher les vis du pignon, mais
contrler que pendant le montage les vis
ne se trouvent pas aux extremits des
fentes. Le bras levier va contacter la poulie
de tension. Comme rpre visuel la partie
suprieure du levier tendeur va s aligner
avec l outil de blocage de l arbre came
quand la poulie de tension est tourn
anti-horaire en appliquant la tension avec
une cl hexagonale de 6mm.
Monter l outil de blocage d arbre came
admission H sur les surfaces plates sur l
arbre came.
Mode demploi Il faut toujours se rfrer
au manuel dentretien du constructeur
automobile ou un manuel dinstructions
appropri du constructeur.
www.lasertools.co.uk
5
