ENGINE
SECTION
ACC
ACCELERATOR CONTROL SYSTEM
ACC
CONTENTS
PRECAUTION ............................................... 2
ACCELERATOR CONTROL SYSTEM .............. 3
PRECAUTIONS ................................................... 2
Exploded View .......................................................... 3
Removal and Installation .......................................... 3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 2
Precautions Necessary for Steering Wheel Rotation after Battery Disconnect ..................................... 2
ON-VEHICLE REPAIR .................................. 3
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................. 5
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................. 5
Accelerator Control ................................................... 5
I
Revision: October 2008
ACC-1
2009 Maxima
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003893291
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
Precautions Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000004394033
NOTE:
Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables.
After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1.
2.
3.
4.
5.
6.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
Carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
Disconnect both battery cables. The steering lock will remain released with both battery cables disconnected and the steering wheel can be turned.
Perform the necessary repair operation.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
Perform self-diagnosis check of all control units using CONSULT-III.
Revision: October 2008
ACC-2
2009 Maxima
ACCELERATOR CONTROL SYSTEM
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR
ACCELERATOR CONTROL SYSTEM
Exploded View
INFOID:0000000003893292
ACC
J
AWBIA0717GB
1.
Accelerator pedal and accelerator
position sensor assembly
2.
Locating pins
Removal and Installation
Front
K
INFOID:0000000003893293
REMOVAL
1.
2.
3.
4.
Disconnect the battery negative terminal.
Disconnect the accelerator position sensor electrical connector.
Remove the three accelerator pedal nuts.
Remove the accelerator pedal and accelerator position sensor assembly.
For electrical inspection of the accelerator pedal position sensor. Refer to EC-433, "Component Inspection".
CAUTION:
Do not disassemble the pedal assembly. Do not remove the accelerator pedal position sensor
from the pedal assembly.
Avoid impact from dropping during handling.
Keep the pedal assembly away from water.
INSTALLATION
Installation is in the reverse order of removal.
Align and install accelerator pedal and accelerator position sensor assembly with locating pins in locating pin
holes.
Check the accelerator pedal for smooth operation. There should be no binding or sticking when applying or
releasing the accelerator pedal.
Revision: October 2008
ACC-3
2009 Maxima
ACCELERATOR CONTROL SYSTEM
< ON-VEHICLE REPAIR >
Check that the accelerator pedal moves through the full specified
distance of pedal travel.
Pedal travel A
: 48.5 - 53.5 mm (1.91 - 2.11 in)
ALBIA0168GB
CAUTION:
When the harness connector of the accelerator pedal position sensor is disconnected, perform the
Accelerator pedal released position learning. Refer to EC-18, "ACCELERATOR PEDAL RELEASED
POSITION LEARNING : Special Repair Requirement".
Revision: October 2008
ACC-4
2009 Maxima
SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Accelerator Control
INFOID:0000000003893294
ACC
PEDAL TRAVEL
C
F
ALBIA0168GB
Accelerator pedal - total travel (A)
48.5 - 53.5 mm (1.91 - 2.11 in)
Revision: October 2008
ACC-5
2009 Maxima
