SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS
REV. 00
www.cobra.it
MAKE
CITROEN
MOD.
XSARA 2
YEAR.
01
PETROL
DIESEL
ALARM/SIREN
POSITION
Position the compact alarms and the sirens behind the drivers side headlamp. To
do that it is suggested to take off the air filter.
CENTRAL UNIT POSITION
Position the modular systems and the modules under the dashboard, drivers
side.
POWER SUPPLY
+ 30: connect to the general supply wire of the fuse box.
- 31: connect with a cable terminal directly to the car body.
IGNITION WIRE
+ 15/54: connect to the wire coming out of the 3A fuse (to insert) foreseen as
supply for additional accessories located in the shunting box placed on the side of
the battery.
DIRECTION INDICATORS
Connect to the wires at the positions nr.14 and nr.15 in the 16 way black
connector coming out of the (BSI) accessories operating central located under
the fuse box.
ELECTRIC WINDOWS
Positive control signal
Front window, drivers side:
connect to the GREY wire marked nr. 6010 located at the position nr. 4 of the
window control switch, drivers side.
Front window, passengers side:
cut the wire marked nr. 6061, at the position nr. 5, of the window control switch,
passengers side.
For the connection to the drivers side front window, it is suggested to refer to the
diagram nr. 68.
CENTRAL DOORS LOCKING
Negative control signal
Wire interruption original control
Cut the wire at the position nr. 8 located in the wiring harness coming out of the
26 way blue connector, coming out of the (BSI) accessories operating central
placed under the fuse box. Refer to the diagram nr. 71 for the antithefts of the
Bridge serie or to the diagram nr. 71A for the antithefts of the 3100 serie.
IMMOBILISATION POINT
Gasoil pump
Cut the wire marked nr. 1201 located at the E6 position, in the 46 way black
connector, placed in the lower part of the fuse box, in the engine compartment, in
correspondence of the fuse nr. 52.
STARTER CUT OFF
50: Cut the WHITE wire located in the wiring harness coming out of the connector
of the ignition key.
BONNET SWITCH
Install an additional switch on the front headlamp support plate, drivers side. It is
necessary to bore also the plastic cover.
DOORS AND BOOT SWITCH
Connect to the wire at the position nr. 14, of the 26 way blue connector, coming
out of the (BSI) accessories operating central located under the fuse box.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
cixs201gbd.doc
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS
REV. 00
www.cobra.it
FITTING DIAGRAM N 68
Diagram to make the windows locking with automatism on
XSARA 2
Antitheft central with
BROWN/WHITE
(time to 24s)
Relay to reverse
the polarity
Original switches with automatic
windows locking system
left window
right window
1052
+30
1 2 3 4 5
BROWN/WHITE
DIODES
1N4004
Antitheft central with the
BROWN
Temporized relay
Art. 1055
Original switches with automatic
windows locking system
left window right window
1055
+30
1 2 3 4 5 6 7
BROWN
DIODES 1N4004
Note:
The above diagrams are to make electric windows locking on vehicles with MAGIC system
automatism on both the motors.
In any case, if the motor (passengers side) does not have the automatism, it is necessary to install the
art. 2980 module for windows locking.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
cixs201gbd.doc
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS
REV. 00
www.cobra.it
FITTING DIAGRAM N 71
To make the central doors locking on
CITROEN BERLINGO EVASION XSARA 2 mod. 2001
(for Bridge car alarms)
VIOLET/ORANGE
ORANGE
GREY/BLACK
VIOLET
Towards the
drivers side door
M
Connector coming out of the central doors
locking unit of the vehicle, located behind
the glove compartment, passengers side.
Note: The wire indicated in the alarm fitting instructions of Citroen Berlingo, Evasion and Xsara 2 must
be interrupted as per the above drawing. Pay attention that the position of the wire that must be
interrupted changes as per the vehicle.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
cixs201gbd.doc
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS
REV. 00
www.cobra.it
FITTING DIAGRAM N71A
To make the central doors locking on
CITROEN BERLINGO EVASION XSARA 2 mod. 2001
(for 3100 serie car alarms)
VIOLET/WHITE
ORANGE/WHITE
ORANGE
GREY/BLACK
VIOLET
Towards the
drivers side door
M
Connector coming out of the central doors
locking unit of the vehicle, located behind
the glove compartment, passengers side.
Note: The wire indicated in the alarm fitting instructions of Citroen Berlingo, Evasion and Xsara 2 must
be interrupted as per the above drawing. Pay attention that the position of the wire that must be
interrupted changes as per the vehicle.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
cixs201gbd.doc
