79.
0
S2 S2
S p a r e
p a r t s
S2
SA16.1
SAR 16.1
50.0
SA 07.1 SA 16.1
SAR 07.1 SAR 16.1
160.2
S1 / S2
S2
79.0
55.0
54.0
SA 07.1 SA 14.1
SAR 07.1 SAR 14.1
S u b - a s s e m b l i e s
a n d
c o m p o n e n t s
51.0
S2
160.1
53.0
153.2
58.0
56.0
153.1
57.0
152.2
70.0
27
20.0
52.0
153.3
151.0
S1 / S2
152.1
S1 / S2
155.0
153.0
S1 / S2
39
S2
24
59.0
153.5
25.0
019
020
24.0 / 23.0
22.0
70.1
49.0
5.0
5.7
S2
5.12
19.0
17.0
5.8
S2
9.0
5.37
5.32
30.0
10.0
S2
18
105.0
S1 / S2
053
1.0
S2
012
6
3.0
156.0
60.0
14
80.001
107
100
80.0
90.001
106.0
80.3
S2
61.0
80.001
S2
90.0
15.0
85.0
S2
1.01
DO 01.11.001 GB
85.001
2.0
B1 / C
90.001
85.001
B3 / B4 / E
SA 07.1 SA 16.1
SAR 07.1 SAR 16.1
List of spare parts
When placing orders for spare parts, it is essential to mention type of actuator and our commission number
(refer to name plate).
No.
Type
Designation
No.
Type
Designation
012
Notched pin
57.0
Pin for motor
019
Cheese head screw
58.0
Wire for protective earth
Pin for motor and thermoswitch in motor plug
60.0
Control unit assly. (but without torque head,
without switches)
1)
020
Clamping washer
053
Countersunk screw
1.0
Housing assly.
2.0
Flange, bottom assly.
61.0
Torque switching head
3.0
Hollow shaft assly. (without worm wheel)
70.0
Motor
5.0
Worm shaft assly.
70.1
1)
Motor pin carrier (without pins)
5.7
Motor coupling
79.0 2)
Planetary gearing for motor drive assly.
5.8
Manual drive coupling assly.
5.12
Grub screw
80.0
Output drive Form A assly. (without thread in
stem nut)
5.32
Coupling pin
Thrust bearing set
5.37
Pull rod assly.
80.3
3)
Stem nut Form A (without thread)
Worm wheel
85.0 3)
Output drive B3
9.0
Planetary gear for manual drive assly.
85.0013)
Snap ring
Output drive D
Snap ring
100
Switch for limit / torque switching
(including pins at wires)
105.0
Blinker transmitter including pins at wires
(without impulse disk and insulation plate)
59.0
80.0013)
3)
10.0
Retaining flange assly.
90.0
14
Change-over lever
90.0013)
15.0
Cover for switch compartment assly.
17.0
Torque lever assly.
18
Gear segment
19.0
Crown wheel assly.
20.0
Swing lever assly.
106.0
Stud bolt for switches
22.0
Drive pinion II for torque switching assly.
107
Spacer
23.0
Drive wheel for limit switching assly.
151.0
Space heater
24
Drive wheel for limit switching
152.1 3)
Potentiometer (without slip clutch)
24.0
Intermediate wheel for limit switching assly.
152.2 3)
Slip clutch for potentiometer
3)
RWG assly.
25.0
Locking plate
153.0
27
Screw plug
153.1 3)
Potentiometer for RWG (without slip clutch)
30.0
Handwheel with ball handle assly.
153.2
3)
Slip clutch for RWG
39
Screw plug
153.3 3)
Electronic board RWG
49.0 1)
Motor plug, socket assly.
153.5 3)
Wires for RWG
3)
50.0
Plug cover assly.
155.0
Reduction gearing
51.0
Socket carrier assly. (with sockets)
156.0 3)
Mechanical position indicator
52.0
Pin carrier (without pins)
160.1
3)
Protection tube (without cap)
53.0
Socket for control
160.2 3)
Cap for stem protection tube
54.0
Socket for motor
S1
Seal-kit, small
55.0
Socket for protective earth
S2
Seal-kit, large
56.0
Pin for control
Type B = Sub-assembly
Type E = Component
Type S = Set
assly. = assembly
1) SA 16.1 with output speeds 32 to 180 rpm without motor plug / socket; motor directly wired to pin carrier (52.0)
2) only required for some output speeds
3) optional extra, not included in basic equipment
Issue
1.01
DO 01.11.001GB
