Model

# 7560
7561

45PC. TAP AND DIE SET

OPERATORS MANUAL

Wear eye
protection

STORE THIS MANUAL IN A SAFE

PLACE FOR FUTURE REFERENCE

Use proper
lubrication

WARNING: FOR HAND CUTTING APPLICATIONS ONLY. Do not

use for machine cutting. Read operators manual before use. Cutting
threads are sharp. Handle and store with care. Wear impact-resistant
protective eyewear in work area at all times. Use proper lubricant for
material being cut. Dry cutting of most material will damage cutting
threads. Select correct type and size of tap or die for work. Disconnect
electric power source before working on or near conductive metal.
These tools are not insulated from shock or electrocution.

Questions?

We would like to hear from you.

888-648-8665
support@tektontools.com

Lubrication
Be sure to use the proper lubricant while threading. Lubrication is necessary for accurately formed threads. It
also prevents damage to taps and dies, helping to extend tool life. The lubricant should be applied to the cutting
edges during the threading operation.
Carbon steel

Petroleum-based or synthetic cutting oil

Alloy steel

Mix of 90% petroleum-based cutting oil and 10% kerosene (or mineral spirits)

Stainless steel

Mix of 90% petroleum-based cutting oil and 10% kerosene (or mineral spirits)

Cast iron

Dry (no lubricant) using air blast to clear chips

Aluminum

Mix of 80% Kerosene (or mineral spirits) and 20% petroleum-based cutting oil

Brass

Kerosene or mineral spirits

Bronze

Mix of 90% Kerosene (or mineral spirits) and 10% petroleum-based cutting oil

Using Taps
Taps are used to cut threads inside a hole, creating a threaded receiver for a bolt
or screw. The taps in this set are called plug taps. They are the most common,
general-purpose tap design. They feature a tapered end of 3 to 5 chamfered
threads, allowing an easier gradual entry into hole. Bottoming taps (1 to 1-1/2
chamfered threads), used for tapping to the bottom of a blind hole and taper taps
(8 to 10 chamfered threads), designed for easiest starting, are both available but
not included in this set. These types of taps are generally not needed by the
average user.

To properly cut internal

threads you will need:
Tap of correct size
Tap wrench
Drill bit of correct size
Lubricating (cutting) oil
Material

1.) Check Hardness

Do not try to thread hardened metals. Use

a file to test the hardness of material. If it
cannot be cut by a file, the material is too
hard for use with the taps and dies in this set.

2.) Drill

90
MATERIAL

Starting with the proper hole size is very important. An oversized hole will
produce poorly formed threads with reduced thread depth. A hole that is too
small will make turning tap very difficult and may break tap. Refer to the
included Tap Drill Charts for the recommended drill size for each tap size. If
possible, drill using a drill press (recommended) or similar machine. Drilling
hole by hand may result in wobble that will distort the hole, and affect the
performance of tap.

3.) Tap

Insert square end of tap into tap wrench and secure in place. Lubricate cutting edges. Great care must
be used when starting the tap into hole. Tap must be held exactly square (90) to work piece. Begin by
turning tap slowly clockwise. Do not force tap forward into hole. As the tap is turned, it bites into the
material, pulling itself forward into hole. For this reason, the only forward pressure needed is naturally
generated as a part of turning the tap wrench. Once the tap begins to cut, chips of material are formed
between the flutes of tap. These chips must be broken off to relieve pressure against the tap. This
is accomplished by momentarily reversing tap direction every 1/4 to 1/2 revolution, depending on the
resistance encountered. Continue this alternating pattern of forward and reverse rotation until tap passes
through work piece or to desired depth.
Blind hole (does not pass completely through work piece): The starter threads (first 3 to 5 chamfered
threads) on these plug taps do not cut full threads. Therefore, when drilling a blind hole, it is necessary to
make hole deep enough to allow extra room for falling chips and the starter thread to fully clear threaded
section.

WRENCH

90
TAP

MATERIAL

TAP

WRENCH

TAP DRILL CHART (UNC, UNF)

COARSE (UNC)

TAP DRILL CHART (Metric)

FINE (UNF)

COARSE

TAP SIZE

DRILL
SIZE (in.)

TAP SIZE

DRILL
SIZE (in.)

#0-80

3/64

#1-72

#1-64

#53

#2-64

#2-56

#51

#3-48
#4-40

FINE

TAP SIZE

DRILL
SIZE (mm)

TAP SIZE

DRILL
SIZE (mm)

#53

1 x .25

.75

4 x .35

3.6

#50

1.1 x .25

.85

4 x .5

3.5

#3-56

#46

1.2 x .25

.95

5 x .5

4.5

5/64

#4-48

#42

1.4 x .3

1.1

6 x .5

5.5

#43

#5-44

#37

1.6 x .35

1.25

6 x .75

5.25

#5-40

#39

#6-40

#33

1.7 x .35

1.35

7 x .75

6.25

#6-32

#36

#8-36

#29

1.8 x .35

1.45

8 x .5

7.5

#8-32

#29

#10-32

#21

2 x .4

1.6

8 x .75

7.25

#10-24

#25

#12-28

#15

2.2 x .45

1.75

8x1

#12-24

#17

1/4-28

#3

2.5 x .45

2.05

9x1

1/4-20

#7

5/16-24

3 x .5

2.5

10 x .75

9.25

5/16-18

3/8-24

3.5 x .6

2.9

10 x 1

9
8.75

3/8-16

5/16

7/16-20

4 x .7

3.3

10 x 1.25

7/16-14

1/2-20

29/64

4.5 x .75

3.75

11 x 1

10

1/2-13

27/64

9/16-18

33/64

5 x .8

4.2

12 x .75

11.25

9/16-12

31/64

5/8-18

37/64

6x1

12 x 1

11
10.5

5/8-11

17/32

3/4-16

11/16

7x1

12 x 1.5

3/4-10

21/32

7/8-14

13/16

8 x 1.25

6.8

14 x 1

13

7/8-9

49/64

1-14

15/16

9 x 1.25

7.8

14 x 1.25

12.8
12.5

1-8

7/8

1-1/8-12

1-3/64

10 x 1.5

8.5

14 x 1.5

1-1/8-7

63/64

1-1/4-12

1-11/64

11 x 1.5

9.5

16 x 1

15

1-1/4-7

1-7/64

1-1/2-12

1-27/64

12 x 1.75

10.25

16 x 1.5

14.5

1-1/2-6

1-11/32

1-3/4-12

1-43/64

14 x 2

12

18 x 1

17

1-3/4-5

1-35/64

2-12

1-59/64

16 x 2

14

18 x 1.5

16.5

2-4-1/2

1-25/32

18 x 2.5

15.5

20 x 1

19

20 x 2.5

17.5

20 x 1.5

18.5

22 x 2.5

19.5

20 x 2

18

24 x 3

21

22 x 1

21

27 x 3

24

22 x 1.5

20.5

PIPE TAPS
DRILL
SIZE

DECIMAL
EQUIVALENT

THREAD
OD MAX.

1/16-27

.242

.3125

1/8-27

.332

.405

22 x 2

20

1/4-18

7/16

.438

.540

24 x 1.5

22.5

3/8-18

9/16

.562

.675

24 x 2

22

1/2-14

45/64

.703

.840

26 x 1.5

24.5

3/4-14

29/32

.906

1.050

27 x 1.5

25.5

1 - 11-1/2

1-9/64

1.141

1.315

27 x 2

25

TAP SIZE

Using Dies
Dies are used to cut threads on the outside of a rod, creating a threaded
bolt. The diameter of rod is of great importance. It cannot be larger
diameter than die (thread) and preferably .005 - .010 undersized.
Oversized rod may damage the die and will make turning the die very
difficult. Slightly undersized stock is easier to thread and still furnishes
enough thread depth for normal applications.

To properly cut external

threads you will need:
Die of correct size
Die stock
Rod of correct diameter
Lubricating (cutting) oil

1.) Check Hardness

Do not try to thread hardened metals. Use a file to test the

hardness of material. If it cannot be cut by a file, the material is
too hard for use with the taps and dies in this set.

2.) Chamfer

To enable die to start easier and straighter, bevel end of

rod. The chamfer can be created by filing or grinding.

3.) Thread

Secure rod in vise or clamp capable of holding rod and preventing it from spinning. Insert the die into die
stock, blank side down. When positioned correctly, the side of die with size markings should be facing you.
This is the chamfered side of the die and is used to start threading. Align recess in die with screw in die
stock. Tighten screw to secure. Lubricate die threads. Place the die over end of rod, exactly square (90) to
rod. Start slowly turning clockwise to start threading. Do not force die forward. As die is turned, it bites into
material, pulling itself along rod. For this reason, the only forward pressure needed is naturally generated as
a part of turning the die stock. Once the die begins to cut, chips of material are formed between the flutes of
die. These chips must be broken off to relieve pressure against the die. This is accomplished by momentarily
reversing die direction every 1/4 to 1/2 revolution, depending on the resistance encountered. Continue this
alternating pattern of forward and reverse rotation until desired thread length is completed.

DIE

ROD

DIE STOCK

90

Chasing Threads
Most threads that have become lightly damaged or rusted can be repaired. Use included thread gauge to
measure thread size. Choose correct tap or die size. Follow original instructions for threading using either
tap or die. Work slowly, make sure that the tap/die is following existing threads, and is not wandering.
Threads will be ruined if tap/die begins to cut new material or becomes cross threaded.

DIE

BOLT

DIE STOCK

90

UNIFIED SCREW THREADS

EXTERNAL (CLASS 2A)
THREAD SIZE ALLOWANCE
4-40 UNC
6-32 UNC
8-32 UNC
10-24 UNC
10-32 UNF
12-24 UNC
1/4-20 UNC
1/4-28 UNF
5/16-18 UNC
5/16-24-UNF
3/8-16 UNC
3/8-24 UNF
7/16-14 UNC
7/16-20 UNF
1/2-13 UNC
1/2-20 UNF
9/16-12 UNC
9/16-18 UNF
5/8-11 UNC
5/8-18 UNF
3/4-10 UNC
3/4-16 UNF
7/8-9 UNC
7/8-14 UNF
1-8 UNC
1-14 UNS

0.0008
0.0008
0.0009
0.0010
0.0009
0.0010
0.0011
0.0010
0.0012
0.0011
0.0013
0.0011
0.0014
0.0013
0.0015
0.0013
0.0016
0.0014
0.0016
0.0014
0.0018
0.0015
0.0019
0.0016
0.002
0.0017

MAJOR
DIAMETER
MAX.
0.1112
0.1372
0.1631
0.1890
0.1891
0.2150
0.2489
0.2490
0.3113
0.3114
0.3737
0.3739
0.4361
0.4362
0.4985
0.4987
0.5609
0.5611
0.6234
0.6236
0.7482
0.7485
0.8731
0.8734
0.998
0.9983

INTERNAL (CLASS 2B)

MAJOR
DIAMETER
MIN
0.1061
0.1312
0.1571
0.1818
0.1831
0.2078
0.2408
0.2425
0.3026
0.3042
0.3643
0.3667
0.4258
0.4281
0.4876
0.4906
0.5495
0.5524
0.6113
0.6105
0.7353
0.7391
0.8592
0.8631
0.983
0.988

MINOR
DIAMETER
0.0805
0.0989
0.1248
0.1379
0.1508
0.1639
0.1876
0.2052
0.2431
0.2603
0.2970
0.3228
0.3485
0.3749
0.4041
0.4374
0.4587
0.4929
0.5119
0.5554
0.6255
0.6718
0.7408
0.7884
0.8492
0.9132

MINOR
DIAMETER
MAX
0.0849
0.104
0.130
0.145
0.156
0.171
0.196
0.211
0.252
0.267
0.307
0.330
0.360
0.383
0.417
0.446
0.472
0.502
0.527
0.565
0.642
0.682
0.778
0.814
0.89
0.938

MINOR
DIAMETER
MIN
0.0939
0.114
0.139
0.156
0.164
0.181
0.207
0.220
0.265
0.277
0.321
0.340
0.376
0.395
0.434
0.457
0.490
0.515
0.546
0.578
0.663
0.696
0.755
0.798
0.865
0.923

MAJOR
DIAMETER
MIN
0.1120
0.1380
0.1640
0.1900
0.1900
0.2160
0.2500
0.2500
0.3125
0.3125
0.3750
0.3750
0.4375
0.4375
0.5000
0.5000
0.5625
0.5625
0.6250
0.6250
0.7500
0.7500
0.875
0.875
1
1

METRIC SCREW THREADS

EXTERNAL (CLASS 6G)
THREAD SIZE

OD (in
inches)

M1.6 x 0.35
M2 x 0.4
M2.5 x 0.45
M3 x 0.5
M3.5x 0.6
M4 x 0.7
M5 x 0.8
M6 x 1
M6 x 0.75
M8 x 1.25
M8 x 1
M10 x 1.5
M10 x 1.25
M12 x 1.75
M12 x 1.5
M12 x 1.25
M12 x 1
M14 x 2
M14 x 1.5
M15 x 1
M16 x 2
M16 x 1.5
M17 x 1
M18 x 2.5
M18 x 1.5
M20 x 2.5
M20 x 1.5
M22 x 2.5
M22 x 1.5
M24 x 3.0
M24 x 1.5

0.0629
0.0787
0.0984
0.1181
0.1378
0.1575
0.1968
0.2362
0.2362
0.3149
0.3149
0.3937
0.3937
0.4724
0.4724
0.4724
0.4724
0.5511
0.5511
0.5905
0.6299
0.6299
0.6693
0.7087
0.7087
0.7874
0.7874
0.8661
0.8661
0.9448
0.9448

INTERNAL (CLASS 6H)

MAJOR
MAJOR
MINOR
MINOR
DIAMETER DIAMETER DIAMETER DIAMETER
MAX
MIN
MAX
MIN

1.581
1.981
2.480
2.980
3.479
3.978
4.976
5.974
5.978
7.972
7.974
9.968
9.972
11.966
11.968
11.972
11.974
13.962
13.968
14.974
15.962
15.968
16.974
24.698
17.968
19.958
19.97
23.96
21.968
23.95
23.97

1.496
1.886
2.380
2.874
3.354
3.838
4.826
5.794
5.838
7.760
7.794
9.732
9.760
11.701
11.732
11.760
11.794
13.682
13.732
14.794
15.682
15.732
16.794
17.62
17.732
19.623
19.73
23.62
21.732
23.58
23.73

1.202
1.548
1.993
2.439
2.829
3.220
4.110
4.891
5.838
6.619
6.891
8.344
8.619
10.072
10.344
10.619
10.891
11.797
12.344
13.891
13.797
14.344
15.891
15.252
16.344
17.252
18.344
21.252
20.344
20.704
22.344

1.075
1.408
1.840
2.272
2.635
3.002
3.869
4.596
4.929
6.272
6.596
7.938
8.272
9.601
9.930
10.258
10.590
11.271
11.930
13.590
13.271
13.930
15.590
14.624
15.930
16.624
17.93
20.604
19.93
19.955
21.92

MINOR
MINOR
MAJOR
MAJOR
DIAMETER DIAMETER DIAMETER DIAMETER
MIN
MAX
MIN
MAX

1.221
1.567
2.013
2.459
2.850
3.242
4.134
4.917
4.929
6.647
6.917
8.376
8.647
10.106
10.376
10.647
10.917
11.835
12.376
13.917
13.835
14.376
15.917
15.294
16.376
17.294
18.376
21.294
20.376
20.752
22.376

1.321
1.679
2.138
2.599
3.010
3.422
4.334
5.153
5.378
6.912
7.153
8.676
8.912
10.441
10.676
10.912
11.153
12.210
12.676
14.153
14.210
14.676
16.153
15.744
16.676
17.744
18.676
21.744
20.676
21.252
22.676

1.600
2.000
2.500
3.000
3.500
4.000
5.000
6.000
6.000
8.000
8.000
10.000
10.000
12.000
12.000
12.000
12.000
14.000
14.000
15.000
16.000
16.000
17.000
18.000
18.000
20.000
20.000
24.000
22.000
24.000
24.000

1.736
2.148
2.66
3.172
3.699
4.219
5.24
6.294
6.24
8.34
8.294
10.396
10.34
12.453
12.406
12.36
12.304
14.501
14.406
15.304
16.501
16.406
17.304
18.585
18.406
20.585
20.406
24.611
22.406
24.698
24.417

DRILL SIZE CHART

DRILL
SIZE

DIA.
(INCH)

DIA.
(METRIC)

DRILL
SIZE

DIA.
(INCH)

DIA.
(METRIC)

DRILL
SIZE

DIA.
(INCH)

DIA.
(METRIC)

2.5 mm

0.0984

2.5000

4.1 mm

0.1614

4.1000

5.8 mm

0.2284

5.8000

#39

0.0995

2.5273

4.2 mm

0.1654

4.2000

5.9 mm

0.2323

5.9000

#38

0.1015

2.5781

#19

0.1660

4.2164

0.2340

5.9436

2.6 mm

0.1024

2.6000

4.3 mm

0.1693

4.3000

15/64 in

0.2344

5.9531

#37

0.1040

2.6416

#18

0.1695

4.3053

6 mm

0.2362

6.0000

2.7 mm

0.1063

2.7000

11/64 in

0.1719

4.3656

0.2380

6.0452

#36

0.1065

2.7051

#17

0.1730

4.3942

6.1 mm

0.2402

6.1000

7/64 in

0.1094

2.7781

4.4 mm

0.1732

4.4000

0.2420

6.1468

#35

0.1100

2.7940

#16

0.1770

4.4958

6.2 mm

0.2441

6.2000

2.8 mm

0.1102

2.8000

4.5 mm

0.1772

4.5000

0.2460

6.2484

#34

0.1110

2.8194

#15

0.1800

4.5720

6.3 mm

0.2480

6.3000

#33

0.1130

2.8702

4.6 mm

0.1811

4.6000

1/4 in

0.2500

6.3500

2.9 mm

0.1142

2.9000

#14

0.1820

4.6228

0.2500

6.3500

#32

0.1160

2.9464

#13

0.1850

4.6990

6.4 mm

0.2520

6.4000

3 mm

0.1181

3.0000

4.7 mm

0.1850

4.7000

6.5 mm

0.2559

6.5000

#31

0.1200

3.0480

3/16 in

0.1875

4.7625

0.2570

6.5278

3.1 mm

0.1221

3.1000

4.8 mm

0.1890

4.8000

6.6 mm

0.2598

6.6000

1/8 in

0.1250

3.1750

#12

0.1890

4.8006

0.2610

6.6294

3.2 mm

0.1260

3.2000

#11

0.1910

4.8514

6.7 mm

0.2638

6.7000

#30

0.1285

3.2639

4.9 mm

0.1929

4.9000

17/64 in

0.2656

6.7469

3.3 mm

0.1299

3.3000

#10

0.1935

4.9149

0.2660

6.7564

3.4 mm

0.1339

3.4000

#9

0.1960

4.9784

6.8 mm

0.2677

6.8000

#29

0.1360

3.4544

5 mm

0.1969

5.0000

6.9 mm

0.2717

6.9000

3.5 mm

0.1378

3.5000

#8

0.1990

5.0546

0.2720

6.9088

#28

0.1405

3.5687

5.1 mm

0.2008

5.1000

7 mm

0.2756

7.0000

9/64 in

0.1406

3.5719

#7

0.2010

5.1054

0.2770

7.0358

3.6 mm

0.1417

3.6000

13/64 in

0.2031

5.1594

7.1 mm

0.2795

7.1000

#27

0.1440

3.6576

#6

0.2040

5.1816

0.2810

7.1374

3.7 mm

0.1457

3.7000

5.2 mm

0.2047

5.2000

9/32 in

0.2813

7.1438

#26

0.1470

3.7338

#5

0.2055

5.2197

7.2 mm

0.2835

7.2000

#25

0.1495

3.7973

5.3 mm

0.2087

5.3000

7.3 mm

0.2874

7.3000

3.8 mm

0.1496

3.8000

#4

0.2090

5.3086

0.2900

7.3660

#24

0.1520

3.8608

5.4 mm

0.2126

5.4000

7.4 mm

0.2913

7.4000

3.9 mm

0.1535

3.9000

#3

0.2130

5.4102

0.2950

7.4930

#23

0.1540

3.9116

5.5 mm

0.2165

5.5000

7.5 mm

0.2953

7.5000

5/32 in

0.1563

3.9688

7/32 in

0.2188

5.5563

19/64 in

0.2969

7.5406

#22

0.1570

3.9878

5.6 mm

0.2205

5.6000

7.6 mm

0.2992

7.6000

4 mm

0.1575

4.0000

#2

0.2210

5.6134

0.3020

7.6708

#21

0.1590

4.0386

5.7 mm

0.2244

5.7000

7.7 mm

0.3032

7.7000

#20

0.1610

4.0894

#1

0.2280

5.7912

7.8 mm

0.3071

7.8000

DRILL SIZE CHART

DRILL
SIZE

DIA.
(INCH)

DIA.
(METRIC)

DRILL
SIZE

DIA.
(INCH)

DIA.
(METRIC)

7.9 mm

0.3110

5/16 in

0.3125

8 mm

DRILL
SIZE

DIA.
(INCH)

DIA.
(METRIC)

7.9000

0.4130

7.9375

10.5 mm

0.4134

10.4902

49/64 in

0.7656

19.4469

10.5000

19.5 mm

0.7677

0.3150

8.0000

27/64 in

19.5000

0.4219

10.7156

25/32 in

0.7813

19.8438

0.3160

8.0264

11 mm

0.4331

11.0000

20 mm

0.7874

20.0000

8.1 mm

0.3189

8.1000

7/16 in

0.4375

11.1125

51/64 in

0.7969

20.2406

8.2 mm

0.3228

8.2000

11.5 mm

0.4528

11.5000

20.5 mm

0.8071

20.5000

0.3230

8.2042

29/64 in

0.4531

11.5094

13/16 in

0.8125

20.6375

8.3 mm

0.3268

8.3000

15/32 in

0.4688

11.9063

21 mm

0.8268

21.0000

21/64 in

0.3281

8.3344

12 mm

0.4724

12.0000

53/64 in

0.8281

21.0344

8.4 mm

0.3307

8.4000

31/64 in

0.4844

12.3031

27/32 in

0.8438

21.4313

0.3320

8.4328

12.5 mm

0.4921

12.5000

21.5 mm

0.8465

21.5000

8.5 mm

0.3347

8.5000

1/2 in

0.5000

12.7000

55/64 in

0.8594

21.8281

8.6 mm

0.3386

8.6000

13 mm

0.5118

13.0000

22 mm

0.8661

22.0000

0.3390

8.6106

33/64 in

0.5156

13.0969

7/8 in

0.8750

22.2250

8.7 mm

0.3425

8.7000

17/32 in

0.5313

13.4938

22.5 mm

0.8858

22.5000

11/32 in

0.3438

8.7313

13.5 mm

0.5315

13.5000

57/64 in

0.8906

22.6219

8.8 mm

0.3465

8.8000

35/64 in

0.5469

13.8906

23 mm

0.9055

23.0000

0.3480

8.8392

14 mm

0.5512

14.0000

29/32 in

0.9063

23.0188

8.9 mm

0.3504

8.9000

9/16 in

0.5625

14.2875

21/23 in

0.9130

23.1913

9 mm

0.3543

9.0000

14.5 mm

0.5709

14.5000

59/64 in

0.9219

23.4156

0.3580

9.0932

37/64 in

0.5781

14.6844

23.5 mm

0.9252

23.5000

9.1 mm

0.3583

9.1000

15 mm

0.5906

15.0000

15/16 in

0.9375

23.8125

23/64 in

0.3594

9.1281

19/32 in

0.5938

15.0813

24 mm

0.9449

24.0000

9.2 mm

0.3622

9.2000

39/64 in

0.6094

15.4781

61/64 in

0.9531

24.2094

9.3 mm

0.3661

9.3000

15.5 mm

0.6102

15.5000

24.5 mm

0.9646

24.5000

0.3680

9.3472

5/8 in

0.6250

15.8750

31/32 in

0.9688

24.6063

9.4 mm

0.3701

9.4000

16 mm

0.6299

16.0000

25 mm

0.9843

25.0000

9.5 mm

0.3740

9.5000

41/64 in

0.6406

16.2719

63/64 in

0.9844

25.0031

3/8 in

0.3750

9.5250

16.5 mm

0.6496

16.5000

1 in

1.0000

25.4000

0.3770

9.5758

17 mm

0.6693

17.0000

9.6 mm

0.3780

9.6000

43/64 in

0.6719

17.0656

9.7 mm

0.3819

9.7000

11/16 in

0.6875

17.4625

9.8 mm

0.3858

9.8000

17.5 mm

0.6890

17.5000

0.3860

9.8044

45/64 in

0.7031

17.8594

9.9 mm

0.3898

9.9000

18 mm

0.7087

18.0000

25/64 in

0.3906

9.9219

23/32 in

0.7188

18.2563

10 mm

0.3937

10.0000

18.5 mm

0.7284

18.5000

0.3970

10.0838

47/64 in

0.7344

18.6531

0.4040

10.2616

19 mm

0.7480

19.0000

13/32 in

0.4063

10.3188

3/4 in

0.7500

19.0500

LIFETIME REPLACEMENT GUARANTEE

If this product does not meet your expectations, we will
replace it or provide replacement parts free of charge. To
arrange for shipping of your replacement product or parts,
or if you have any other questions, email us at support@
tektontools.com or call us at 1-888-648-8665.

Michigan Industrial Tools

3707 Roger B. Chaffee Dr.
Grand Rapids, MI 49548
Printed in China

Copyright 2012
Michigan Industrial Tools
WWW.TEKTONTOOLS.COM

This manual is the sole property of Michigan Industrial Tools. No part of this manual,
may be reproduced in any form, without the express written consent of Michigan Industrial Tools.