Torqlink Series

Hydraulics

Small and Large Frame

Low Speed High Torque
Hydraulic Motors

Catalog No. 1510-20-002/USA

November, 1997

Low Speed High Torque Motors

Catalog 1510-20

! WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR
RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system
options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review
the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for
these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and
systems and assuring that all performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change
by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this document entitled "Offer of Sale".
1997, Parker Hannifin Corporation
PSLGC.PM6, dg, ki

110

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Index
Torqlink Series Small and Large Frame
Introduction

Small Frame
Quick Reference Data Chart

TA Series

4 15

TB Series

16 27

TD Series

28 40

Large Frame
Quick Reference Data Chart

41

TF Series

42 61

TG Series

62 82

TH Series

83 97

Accessories

Cross-Over Relief Valve

98 99

Cross Port Relief

100

Hot Oil Shuttle

100

Speed Sensor

101

Installation/Operation Information

102

Engineering Data

103 106

Offer of Sale

108

Warning
This Catalog is not a Controlled Document. All Dimensions listed herein are for reference only. Consult a
Sales engineer for detailed information.
PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Small and Large Frame Torqlink

Catalog 1510-20

Introduction
Excellence of Design
The producers of Parker Hannifins TorqlinkTM
Series motors have a history of manufacturing
reliable, precision parts that stretches back over
ninety years. Milestones include the first patent on
roller vane rotor sets for low speed, high torque
hydraulic motors. That was thirty years ago. Today
the technological advances continue.
In the Development Laboratory, engineers continuously measure and analyze motor data to move
existing products to even higher levels of performance and to develop new products to serve the
ever changing needs of our customers. Design
integrity is assured by exhaustive testing on endurance stands. To be sure that this translates into
superior performance, advanced manufacturing
techniques are employed as well.

Excellence of Manufacturing
Central to manufacturing excellence is the understanding that quality parts make quality motors. The
instrumentation in our Quality Assurance laboratory
includes devices such as coordinate measuring
machines, to accurately measure the parts that we
manufacture as well as those that we purchase.
Quality cannot be inspected in, however. It must be
manufactured. Each machine operator is responsible for the quality of the part that comes off that
machine. Efficiency is enhanced by our cellular
manufacturing techniques. Accuracy is assured by
statistical process control methods. Micrometers
and specialized gages are at the disposal of the
operator. As a final check, every motor is tested
before shipment to our customer. Parker understands that our customers cannot produce quality
products unless we do.

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Small Frame Torqlink

Catalog 1510-20

Quick Reference Data Chart

Quick Reference Data Chart

Series

TA

TB

TD

45 - 392
(2.7 - 24.0)

45 - 392
(2.7 - 24.0)

45 - 392
(2.7 - 24.0)

Max Continuous Pressure

bar
(psi)

86.2
(1250)

124.1
(1800)

137.9
(2000)

Max Intermittent Pressure

bar
(psi)

120.7
(1750)

165.5
(2400)

172.4
(2500)

Max Continuous Torque

nm
(lb in)

215.2
(1905)

428.4
(3792)

444.6
(3935)

Max Intermittent Torque

nm
(lb in)

306.1
(2709)

524.5
(4642)

538.7
(4768)

Displacement
cc/rev
(cu in/rev)

Max Continuous Flow

LPM
(GPM)

45
(12)

45
(12)

57
(15)

Max Intermittent Flow

LPM
(GPM)

57
(15)

57
(15)

76
(20)

Max Speed
RPM

810

785

835

625
(1405)

704
(1582)

1100
(2473)

Max Radial Load

daN
(lb)

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
M
A
L
L
F
R
A
M
E
T
O
R
Q
L
I
N
K

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Technical Information

T
A
S
E
R
I
E
S

Compact Power In An Economical

Package
Use of a shaft speed disc valve allows Parkers TA
Series motors to pack 2700 lb ins of torque into less
than six inches of length. These low cost motors
contain many features not normally found in motors
of this type. When used within their ratings, they
assure long trouble free life.

Options

Features

All Common 1 inch Shafts

Roller Vane Power Element For High Volumetric Efficiency and Long Life

SAE A 2 Bolt or 4 Bolt Mounting

High Pressure Shaft Seal For High Back

Pressure Operation Without External Drains

SAE O-Ring, NPTF or Manifold Porting

External Crossover Relief Valve Package

High Flow Shaft Seal Cooling For Long Seal

Life

Free Running Rotor Set

60:40 Spline Geometry For Superior Powertrain Strength, Long Life

TA Specifications
Code
Displacement

0045 0050 0065

cc/rev
(cu in/rev)

43
(2.7)

49
(3.0)

66
(4.0)

82
(5.0)

98
(6.0)

810

688

517

413

460

Maximum Speed (rpm) @

Maximum Continuous Flow
Pressure Differential
Maximum Continuous
Maximum Intermittent

0080 0100 0130 0165

0195 0230 0260 0295 0330 0365

131
164
197
(8.0) (10.0) (12.0)

154

138

121

115

bar
(psid)

86.2
86.2
86.2
86.2
86.2
86.2
86.2
86.2
75.9
65.5
(1250) (1250) (1250) (1250) (1250) (1250) (1250) (1250) (1100) (950)

58.6
(850)

51.7
(750)

44.8
(650)

44.8
(650)

bar
(psid)

120.7 120.7 120.7 120.7 120.7 120.7 120.7 120.7 106.9

96.6
86.2
75.9
(1750) (1750) (1750) (1750) (1750) (1750) (1750) (1750) (1550) (1400) (1250) (1100)

65.5
(950)

65.5
(950)

85.1
(753)

278

231

198

393
(24.0)

174

Max. Torque @ Max.Continuous

Pressure
nm
(lb-in)
Max. Torque @ Max.Intermittent
Pressure
nm
(lb-in)

346

229
262
295
328
370
(14.0) (16.0) (18.0) (20.0) (22.6)

0390

39.8
(352)

47.8
(423)

65.8
(582)

100.3 137.6 172.7 205.1 215.2 211.3 208.2 205.5 198.5 207.0
(888) (1218) (1529) (1815) (1905) (1870) (1843) (1819) (1757) (1832)

56.0
(496)

66.5
(589)

91.5 118.6 140.1 191.7 238.4 286.1 297.9 306.1 300.2 296.1 290.4 296.2
(810) (1050) (1240) (1697) (2110) (2532) (2637) (2709) (2657) (2621) (2570) (2622)

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Technical Information
Maximum Side Load Capacity

Performance Data

Shaft Side Load - kg (lbs)

907
(2000)

Continuous / Intermittent* Operation

S
E
R
I
E
S

Continuous
680
(1500)

Intermittent*

454
(1000)

*Intermittent operation is defined as less

than 10% of each minute.

Performance data based on testing using 15W40 oil

with a viscosity of 200 SUS at 54 C (130 F.)
227
(500)

Performance data is typical. Actual data may vary

slightly from one production motor to another.
0
-50.8
(-2)

-25.4
(-1)

T
A

0
(0)

25.4
(1)

50.8
(2)

76.2
(3)

101.6
(4)

Distance from Mounting Face - mm (in)

Application of the above uni-directional radial loads will result in a

B-10 life of 2.5 million revolutions. For B-10 life at other radial
loads, apply the factors from the curve below.

B-10 Life Factors

4
3
Multiply
Allowable
Radial Load 2
By These
Factors
1
0

0 2 4 6 8 10 12
Life In Millions Of Revolutions

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data

T
A

Code 0045

Code 0050

45 cc / rev

50 cc / rev

PRESSURE (BAR)
17.2 34.5 51.7 69.0 86.2 103.4 120.7

S
E
R
I
E
S

PRESSURE (BAR)
17.2 34.5 51.7 69.0 86.2 103.4 120.7

1.9

6.3 14.2 21.8 29.1

36
23
14
7

1.9

7.1 15.6 23.6

29
15
5

3.8

6.7 14.8 22.7 30.3 37.5 44.4 51.1

81
68
58
52
38
26
8

3.8

7.7 16.5 25.0 33.2 41.0

68
54
43
32
18

7.6

6.6 14.9 23.2 31.2 39.1 46.8 54.0

171 158 149 142 128 113
94

7.6

7.9 17.7 27.0 35.9 44.5 52.4 59.9

145 131 120 108
93
74
50

11.4

6.3 14.7 23.2 31.3 39.3 47.0 54.5

263 249 239 231 218 202 182

11.4

7.6 17.5 27.2 36.4 45.3 53.7 61.9

222 209 197 186 170 151 125

15.1

5.9 14.3 22.9 31.5 39.8 47.9 55.6

354 340 330 321 307 292 272

15.1

6.9 17.4 27.9 37.8 47.2 56.0 64.2

300 286 275 263 247 228 202

18.9

5.3 13.9 22.5 31.3 39.7 48.0 56.0

445 431 421 411 397 381 360

18.9

6.3 17.1 27.7 38.0 47.8 57.2 65.8

378 364 352 340 324 305 278

26.5

3.6 12.2 20.9 29.8 38.5 47.0 55.2

628 612 602 591 577 559 537

26.5

4.6 15.5 26.3 37.1 47.5 57.3 66.5

533 518 507 494 478 458 432

34.1

1.6 10.4 19.1 28.1 36.7 45.1 53.2

810 794 783 771 756 737 714

34.1

2.7 13.8 24.6 35.4 45.8 55.6 65.2

688 673 661 648 632 612 585

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

45.1
737

3.0 cu in / rev

2.7 cu in / rev

250

500

PRESSURE (PSI)
750 1000 1250 1500 1750

.5

63
29

138
15

209
5

452
8

68
68

146
54

221
43

294
32

363
18

414
113

478
94

70
145

157
131

239
120

318
108

394
93

464
74

530
50

348
218

416
202

482
182

67
222

155
209

241
197

322
186

401
170

475
151

548
125

279
321

352
307

424
292

492
272

61
300

154
286

247
275

335
263

418
247

496
228

568
202

199
421

277
411

351
397

425
381

496
360

56
378

151
364

245
352

336
340

423
324

506
305

582
278

108
612

185
602

264
591

341
577

416
559

489
537

41
533

137
518

233
507

328
494

420
478

507
458

589
432

92
794

169
783

249
771

325
756

399
737

471
714

24
688

122
673

218
661

313
648

405
632

492
612

577
585

250

500

PRESSURE (PSI)
750 1000 1250 1500 1750

.5

56
36

126
23

193
14

258
7

59
81

131
68

201
58

268
52

332
38

393
26

58
171

132
158

205
149

276
142

346
128

56
263

130
249

205
239

277
231

52
354

127
340

203
330

47
445

123
431

32
628

14
810

Flow (GPM)

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

399
737

Performance data is typical.

Actual data may vary slightly from
one production motor to another.
PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data
Code 0065

T
A

Code 0080

65 cc / rev

80 cc / rev

PRESSURE (BAR)

PRESSURE (BAR)
17.2 34.5 51.7 69.0 86.2 103.4 120.7

17.2 34.5 51.7 69.0 86.2 103.4 120.7

1.9

11.3 23.7 36.4 48.8

22
15
10
3

1.9

14.9 31.0 47.1 63.0 78.7

19
15
11
8
3

3.8

11.7 24.5 37.4 50.2 62.7 75.2

51
44
38
31
21
12

3.8

15.6 32.3 48.9 65.4 81.5 97.0 112.3

43
38
34
30
25
18
12

7.6

12.2 25.5 38.9 52.0 64.9 77.6 89.8

109 102
95
88
78
67
53

7.6

15.8 33.2 50.6 67.8 84.6 101.1 116.9

89
84
80
75
70
62
54

11.4

11.5 25.1 38.8 52.1 65.1 77.8 90.4

167 159 153 145 136 124 110

11.4

15.1 32.8 50.3 67.7 84.6 101.2 117.3

135 130 126 121 115 108
99

15.1

10.5 24.6 38.6 52.4 65.8 78.7 91.3

226 217 210 202 193 181 166

15.1

13.9 32.1 50.1 67.8 85.1 102.1 118.6

182 176 172 167 161 153 144

18.9

9.7 24.0 38.1 52.1 65.6 78.7 91.5

284 274 268 260 250 238 223

18.9

12.8 31.1 49.3 67.0 84.5 101.8 118.5

228 223 218 213 207 199 189

26.5

7.6 21.9 36.2 50.4 64.3 77.7 90.7

400 390 383 374 365 352 336

26.5

9.9 28.2 46.4 64.3 82.0 99.3 116.4

321 315 310 304 298 290 279

34.1

5.4 20.2 34.7 49.0 62.8 76.4 89.5

517 505 497 489 479 466 449

34.1

7.5 25.9 44.1 62.0 79.5 96.9 113.8

413 407 402 396 389 381 369

Flow (LPM)

Flow (LPM)

TORQUE
SPEED

(nm)
(RPM)

4.0 cu in / rev

76.4
466

5.0 cu in / rev

PRESSURE (PSI)

PRESSURE (PSI)

250

500

750 1000 1250 1500 1750

250

500

750 1000 1250 1500 1750

.5

100
22

210
15

322
10

432
3

.5

132
19

274
15

417
11

558
8

697
3

104
51

217
44

331
38

444
31

555
21

666
12

138
43

286
38

433
34

579
30

721
25

859
18

108
109

226
102

344
95

460
88

574
78

687
67

795
53

140
89

294
84

448
80

600
75

749
70

895 1035
62
54

102
167

222
159

343
153

461
145

576
136

689
124

800
110

134
135

290
130

445
126

599
121

749
115

896 1038
108
99

93
226

218
217

342
210

464
202

582
193

697
181

808
166

123
182

284
176

443
172

600
167

753
161

904 1050
153 144

86
284

212
274

337
268

461
260

581
250

697
238

810
223

113
228

275
223

436
218

593
213

748
207

901 1049
199 189

67
400

194
390

320
383

446
374

569
365

688
352

803
336

88
321

250
315

411
310

569
304

726
298

879 1030
290 279

48
517

179
505

307
497

434
489

556
479

676
466

792
449

66
413

229
407

390
402

549
396

704
389

858 1007
381 369

Flow (GPM)

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

676
466
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

994
12

S
E
R
I
E
S

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data

T
A

Code 0100

Code 0130

100 cc / rev

130 cc / rev

PRESSURE (BAR)
17.2 34.5 51.7 69.0 86.2 103.4 120.7

S
E
R
I
E
S

PRESSURE (BAR)
17.2 34.5 51.7 69.0 86.2 103.4 120.7

1.9

17.2 36.0 54.8

14
8
3

1.9

24.2 51.3 78.4 105.6 132.4

12
9
7
5
2

3.8

18.1 37.6 57.1 76.3 95.2 113.5

34
27
22
17
12
7

3.8

25.2 52.9 80.4 107.7 134.8 162.0 188.9

27
24
22
19
16
13
8

7.6

19.0 39.4 60.0 80.0 99.8 119.2 137.6

72
65
60
56
50
43
33

7.6

26.1 54.1 82.4 110.2 137.6 164.8 191.7

56
53
51
48
44
41
35

11.4

18.1 38.8 59.3 79.7 99.6 119.2 138.4

111 104
99
94
89
81
71

11.4

25.2 53.3 81.6 109.4 136.8 164.2 190.9

85
82
80
77
74
69
64

15.1

16.5 37.8 59.1 79.9 100.3 120.4 140.1

150 143 138 133 128 120 109

15.1

23.3 52.0 80.4 108.6 136.1 163.6 190.5

114 111 109 106 102
98
93

18.9

15.4 36.8 58.1 79.2 99.8 120.1 140.0

189 182 176 172 166 159 148

18.9

21.4 50.2 78.7 107.1 134.9 162.4 189.2

143 140 138 135 131 127 122

26.5

12.5 33.9 55.0 76.3 97.2 117.7 138.1

266 259 254 249 244 236 225

26.5

17.7 46.2 74.3 102.9 130.9 158.5 185.7

201 198 195 193 189 185 179

34.1

8.1 29.3 50.5 72.0 93.1 113.9 134.4

344 337 331 327 322 313 301

34.1

11.4 39.9 68.1 96.6 124.7 152.5 179.9

259 255 253 250 247 243 237

45.4

1.6 22.8 43.8 65.3 86.2 106.7 126.9

460 453 448 443 438 430 417

45.4

2.6 29.6 56.9 85.1 112.8 140.5 168.1

346 342 340 337 334 329 323

56.8

20.9 48.6 76.3 103.6 130.5 156.9

429 426 423 420 416 410

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

6.0 cu in / rev

106.7
430

8.0 cu in / rev

PRESSURE (PSI)

250

500

750 1000 1250 1500 1750

.5

152
14

319
8

485
3

160
34

333
27

505
22

675
17

168
72

349
65

531
60

160
111

343
104

146
150

PRESSURE (PSI)

250

500

750 1000 1250 1500 1750

.5

214
12

454
9

694
7

935 1172
5
2

843 1005
12
7

223
27

468
24

712
22

953 1193 1434 1672

19
16
13
8

708
56

883 1055 1218

50
43
33

231
56

479
53

729
51

975 1218 1459 1697

48
44
41
35

525
99

705
94

882 1055 1225

89
81
71

223
85

472
82

722
80

968 1211 1453 1690

77
74
69
64

335
143

523
138

707
133

888 1066 1240

128 120 109

206
114

460
111

712
109

961 1205 1448 1686

106 102
98
93

136
189

326
182

514
176

701
172

883 1063 1239

166 159 148

189
143

444
140

697
138

948 1194 1437 1675

135 131 127 122

111
266

300
259

487
254

675
249

860 1042 1222

244 236 225

157
201

409
198

658
195

911 1159 1403 1644

193 189 185 179

72
344

259
337

447
331

637
327

824 1008 1190

322 313 301

101
259

353
255

603
253

855 1104 1350 1592

250 247 243 237

12

14
460

202
453

388
448

578
443

763
438

12

23
346

262
342

504
340

753
337

998 1244 1488

334 329 323

185
429

430
426

675
423

917 1155 1389

420 416 410

944 1123
430 417

Flow (GPM)

15

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

944
430

Performance data is typical.

Actual data may vary slightly from
one production motor to another.

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data
Code 0165

T
A

Code 0195

165 cc / rev

195 cc / rev

PRESSURE (BAR)

PRESSURE (BAR)
17.2 34.5 51.7 69.0 86.2 103.4 120.7

17.2 34.5 51.7 69.0 86.2 103.4 120.7

1.9

30.4 63.5 96.3 129.6 162.4

10
8
6
4
2

1.9

36.5 77.8 119.0 160.8

8
6
5
3

3.8

32.3 66.4 100.3 133.8 166.8 199.3 231.6

21
19
18
16
14
11
8

3.8

37.7 79.2 120.5 162.1 203.5 244.5 286.1

18
16
14
13
11
8
6

7.6

33.6 68.8 104.1 138.6 172.7 206.1 238.4

45
43
41
39
37
34
30

7.6

38.4 80.4 122.1 163.9 205.1 245.1 285.2

37
35
34
32
30
27
24

11.4

32.4 67.7 102.8 137.7 171.8 205.3 237.8

68
66
65
63
61
58
54

11.4

37.3 79.2 121.0 162.7 203.8 243.9 283.6

57
55
54
52
50
47
43

15.1

29.6 65.9 101.7 136.9 171.6 205.4 238.3

91
89
88
86
84
81
77

15.1

34.5 77.1 119.2 160.9 201.7 241.8 281.4

76
74
73
72
70
67
62

18.9

27.2 63.4 99.1 134.6 169.4 203.3 236.4

115 113 111 110 108 105 100

18.9

31.9 74.3 116.5 157.9 198.7 239.0 277.9

95
94
93
91
89
86
82

26.5

22.1 57.3 92.6 128.2 163.3 197.2 230.3

161 159 158 156 154 151 147

26.5

26.3 68.0 109.5 151.2 191.8 231.7 270.5

134 132 132 130 128 125 121

34.1

14.6 49.4 84.5 119.9 154.6 188.6 221.3

208 206 204 203 201 198 194

34.1

17.4 58.9 100.1 141.7 182.0 221.9 260.9

173 171 170 169 167 164 159

45.4

1.8 35.5 69.6 104.3 138.5 172.3 205.1

278 276 274 273 271 269 264

45.4

4.0 43.4 83.3 124.1 164.4 203.9 242.5

231 229 228 228 226 223 218

56.8

24.4 58.7 93.0 126.9 159.9 191.8

346 343 342 341 338 334

56.8

30.7 70.2 109.9 149.2 187.3 224.8

287 286 286 284 281 276

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

159.9
338

10.0 cu in / rev
250

500

PRESSURE (PSI)
750 1000 1250 1500 1750

.5

269
10

562
8

852 1147 1437

6
4
2

286
21

588
19

297
45

12.0 cu in / rev

PRESSURE (PSI)
750 1000 1250 1500 1750

250

500

.5

323
8

689 1053 1423

6
5
3

888 1184 1476 1764 2050

18
16
14
11
8

334
18

701 1067 1435 1801 2164 2532

16
14
13
11
8
6

609
43

921 1227 1529 1824 2110

41
39
37
34
30

340
37

712 1081 1451 1815 2169 2524

35
34
32
30
27
24

287
68

599
66

910 1219 1521 1817 2105

65
63
61
58
54

330
57

701 1071 1440 1804 2159 2510

55
54
52
50
47
43

262
91

583
89

900 1212 1519 1818 2109

88
86
84
81
77

305
76

682 1055 1424 1785 2140 2491

74
73
72
70
67
62

241
115

561
113

877 1191 1499 1799 2092

111 110 108 105 100

282
95

658 1031 1398 1759 2115 2460

94
93
91
89
86
82

196
161

507
159

820 1135 1445 1745 2038

158 156 154 151 147

233
134

602
132

969 1338 1698 2051 2394

132 130 128 125 121

129
208

437
206

748 1061 1368 1669 1959

204 203 201 198 194

154
173

521
171

886 1254 1611 1964 2309

170 169 167 164 159

12

16
278

314
276

616
274

923 1226 1525 1815

273 271 269 264

12

35
231

384
229

737 1098 1455 1805 2146

228 228 226 223 218

216
346

520
343

823 1123 1415 1698

342 341 338 334

15

272
287

621
286

15

Flow (GPM)

973 1321 1658 1990

286 284 281 276

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

1415
338

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data

T
A

Code 0230

Code 0260

230 cc / rev

260 cc / rev

PRESSURE (BAR)
17.2 34.5 51.7 75.9 89.7 106.9

S
E
R
I
E
S

PRESSURE (BAR)
17.2 34.5 51.7 65.5 82.8 96.6

1.9

45.4 94.3 143.4

6
4
3

1.9

52.3 108.0 163.4 207.2 261.5

6
5
4
3
2

3.8

47.0 96.4 145.6 213.4 251.3 297.7

14
13
11
9
7
5

3.8

54.2 110.3 165.9 209.6 263.4 305.2

13
12
11
10
9
8

7.6

47.5 97.5 147.4 215.2 252.5 297.9

31
29
28
26
23
20

7.6

54.7 111.2 167.4 211.3 264.8 306.1

28
27
26
25
24
22

11.4

46.1 95.7 145.1 212.6 249.8 295.2

48
46
45
43
40
37

11.4

53.2 109.5 165.5 209.2 262.7 303.9

42
42
41
40
39
37

15.1

42.8 92.6 142.2 209.4 246.4 291.4

64
63
62
59
57
54

15.1

49.5 106.2 162.5 206.2 259.3 300.4

57
56
56
55
54
52

18.9

39.7 89.5 138.9 205.8 242.6 286.6

81
79
78
76
74
71

18.9

45.5 102.0 158.2 201.8 254.8 295.7

72
71
70
70
68
67

26.5

32.7 82.2 130.9 197.6 234.3 277.8

114 113 112 110 108 104

26.5

37.4 92.5 147.0 190.4 242.8 283.4

101 100 100
99
98
97

34.1

23.2 70.8 118.3 184.8 221.7 266.1

148 146 145 143 141 137

34.1

24.4 78.6 132.5 175.5 227.2 267.4

130 129 129 129 128 126

45.4

6.2 51.5 97.2 162.4 199.0 243.4

198 196 195 193 192 187

45.4

6.7 57.7 108.5 150.2 200.7 240.2

174 173 173 173 172 171

56.8

37.6 83.5 146.8 181.6 223.6

246 244 243 242 237

56.8

40.0 92.9 134.1 184.3 221.9

217 217 217 216 215

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

37.6
246

16.0 cu in / revPRESSURE (PSI)

14.0 cu in / revPRESSURE (PSI)

250

500

.5

463
6

956 1446 1834 2315

5
4
3
2

853 1289 1889 2224 2635

13
11
9
7
5

480
13

976 1468 1855 2331 2701

12
11
10
9
8

420
31

863 1305 1905 2235 2637

29
28
26
23
20

484
28

984 1482 1870 2344 2709

27
26
25
24
22

408
48

847 1284 1882 2211 2613

46
45
43
40
37

471
42

969 1465 1852 2325 2690

42
41
40
39
37

379
64

820 1259 1853 2181 2579

63
62
59
57
54

438
57

940 1438 1825 2295 2659

56
56
55
54
52

351
81

792 1229 1822 2147 2537

79
78
76
74
71

403
72

903 1400 1786 2255 2617

71
70
70
68
67

289
114

728 1159 1749 2074 2459

113 112 110 108 104

331
101

819 1301 1685 2149 2508

100 100
99
98
97

205
148

627 1047 1636 1962 2355

146 145 143 141 137

216
130

696 1173 1553 2011 2367

129 129 129 128 126

12

55
198

456
196

860 1437 1761 2154

195 193 192 187

12

59
174

511
173

960 1329 1776 2126

173 173 172 171

333
246

739 1299 1607 1979

244 243 242 237

15

354
217

822 1187 1631 1964

217 217 216 215

250

500

.5

402
6

835 1269
4
3

416
14

15

750 1100 1300 1550

750

950 1200 1400

Flow (GPM)

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

333
246

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

10

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data
Code 0295

Code 0330

295 cc / rev

330 cc / rev

PRESSURE (BAR)
17.2 34.5 58.6 69.0 86.2

1.9

57.2 119.0 204.6

5
4
2

3.8

59.2 121.1 206.6 242.1 300.1

11
10
9
8
6

7.6

60.2 122.6 208.2 243.2 300.2

24
23
22
21
20

11.4

58.0 120.2 205.6 240.8 297.7

37
36
35
34
33

15.1

53.3 116.1 201.7 236.6 293.4

50
49
48
47
46

18.9

49.3 112.2 197.6 232.4 288.8

63
62
62
61
60

26.5

40.0 101.2 185.3 220.4 276.5

89
89
88
87
86

34.1

26.8 87.2 170.1 205.2 260.8

115 115 114 114 113

45.4

7.7 63.5 142.4 176.5 231.4

154 154 153 153 152

56.8

43.7 123.1 155.8 208.7

193 192 192 192

PRESSURE (BAR)
17.2 34.5 51.7 75.9

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

.5

65.1 133.7 201.1

4
3
2

3.8

67.4 135.7 203.0 294.2

10
9
8
6

7.6

68.9 137.9 205.5 296.1

22
21
20
18

11.4

66.4 135.0 202.3 293.0

33
32
31
30

15.1

61.9 130.8 198.4 288.4

45
44
43
42

18.9

56.9 125.7 193.3 283.2

57
56
55
54

26.5

47.0 114.3 180.4 269.5

80
79
78
78

34.1

31.1 96.4 161.3 249.9

103 102 102 102

45.4

8.8 69.5 130.0 216.2

138 137 137 137

56.8

47.6 108.2 191.6

172 172 172

20.0 cu in / rev

PRESSURE (PSI)
500 850 1000 1250

250

506 1053 1811

5
4
2

.5

524 1072 1829 2143 2656

11
10
9
8
6

533 1085 1843 2153 2657

24
23
22
21
20

513 1064 1820 2131 2635

37
36
35
34
33

472 1028 1785 2094 2597

50
49
48
47
46

436
63

993 1749 2057 2556

62
62
61
60

354
89

896 1640 1951 2447

89
88
87
86

237
115

772 1506 1816 2308

115 114 114 113

12

68
154

562 1260 1562 2048

154 153 153 152

15

1.9

Flow (LPM)

43.7
193

18.0 cu in / rev
250

387 1090 1379 1847

193 192 192 192
(LB IN)
(RPM)

387
193

PRESSURE (PSI)
500 750 1100

576 1183 1780

4
3
2

597 1201 1797 2604

10
9
8
6

610 1221 1819 2621

22
21
20
18

588 1195 1791 2593

33
32
31
30

548 1158 1756 2553

45
44
43
42

504 1113 1711 2507

57
56
55
54

416 1012 1597 2385

80
79
78
78

275
103

853 1428 2212

102 102 102

12

78
138

615 1151 1914

137 137 137

15

Flow (GPM)
TORQUE
SPEED

T
A

421
172

958 1696
172 172

Flow (GPM)
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

11

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Performance Data

T
A
S
E
R
I
E
S

Code 0365

Code 0390

370 cc / rev

390 cc / rev

PRESSURE (BAR)
17.2 34.5 44.8 65.5

PRESSURE (BAR)
17.2 34.5 44.8 65.5

1.9

66.9 144.5 191.6 283.6

4
3
2
1

1.9

75.1 155.6
3
2

3.8

69.9 148.0 194.6 285.4

9
8
7
6

3.8

77.8 157.9 205.3 296.2

8
7
6
5

7.6

72.5 151.2 198.5 290.4

19
18
18
17

7.6

80.0 159.9 207.0 295.9

18
17
16
15

11.4

69.7 148.8 195.9 286.4

30
29
28
27

11.4

77.2 156.9 203.8 293.0

27
26
26
25

15.1

64.1 143.3 190.5 280.6

40
39
39
38

15.1

71.9 151.4 198.3 286.9

37
36
36
35

18.9

60.3 138.7 185.9 274.7

50
49
49
49

18.9

66.2 145.3 191.8 279.7

47
46
46
45

26.5

48.8 125.7 172.3 260.8

71
70
70
69

26.5

54.8 132.2 177.3 264.5

66
66
65
65

34.1

35.5 110.5 156.7 243.9

91
90
90
90

34.1

38.8 115.0 159.5 246.4

86
85
85
85

45.4

9.0 82.8 130.2 216.8

122 121 121 121

45.4

11.6 84.3 127.0 211.6

115 114 114 115

56.8

152

68.6 119.6 207.8

607 1059 1839

56.8

60.6 103.0 184.5

144 143 144

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

119.6
1059

22.6 cu in / rev
250

24.0 cu in / rev
PRESSURE (PSI)

PRESSURE (PSI)
500 650 950

250

500

650

950

.5

592 1279 1696 2510

4
3
2
1

.5

619 1310 1722 2526

9
8
7
6

689 1398 1817 2622

8
7
6
5

642 1338 1757 2570

19
18
18
17

708 1415 1832 2619

18
17
16
15

617 1317 1734 2535

30
29
28
27

683 1389 1804 2593

27
26
26
25

567 1268 1686 2484

40
39
39
38

636 1340 1755 2539

37
36
36
35

534 1228 1645 2431

50
49
49
49

586 1286 1698 2476

47
46
46
45

432 1113 1525 2308

71
70
70
69

485 1170 1569 2341

66
66
65
65

314
91

978 1387 2159

90
90
90

343 1018 1412 2181

86
85
85
85

12

80
122

733 1152 1919

121 121 121

12

15

152

607 1059 1839

152 152 152

15

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

1059
152

665 1377
3
2

103
115

746 1124 1873

114 114 115
536
144

912 1633
143 144

Flow (GPM)
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

12

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Dimensional Data

T
A

Dimensions
Inch equivalents for metric dimensions are shown in (**)

"L"

95.5
(3.76)
Max

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A"
to turn Clockwise, "B" to
turn Counterclockwise.

Length "L" and Weight

Displacement Code

0045 0050 0065 0080 0100 0130 0160 0195 0230 0260 0295 0330 0365 0390

SAE "A" Mount

Length "L"

mm
(inches)
kg

Weight

(lb)

106 108 111

114 117 124
130 136 143 149
155 162 170 174
(4.18) (4.24) (4.36) (4.49) (4.61) (4.86) (5.11) (5.36) (5.61) (5.86) (6.11) (6.36) (6.70) (6.86)
4.89 4.98 5.12 5.26 5.31 5.67 5.92 6.19 6.41 6.69 6.93 7.22 7.58 7.69
(10.8) (11.0) (11.3) (11.6) (11.7) (12.5) (13.1) (13.6) (14.1) (14.7) (15.3) (15.9) (16.7) (17.0)

4 Bolt
mm
Length "L"

(inches)
kg

Weight

(lb)

106 108 111

114 117 124
130 136 143 149
155 162 170 174
(4.18) (4.24) (4.36) (4.49) (4.61) (4.86) (5.11) (5.36) (5.61) (5.86) (6.11) (6.36) (6.70) (6.86)
4.59 4.68 4.82 4.96 5.01 5.37 5.63 5.89 6.11 6.39 6.63 6.92 7.26 7.39
(10.1) (10.3) (10.6) (10.9) (11.1) (11.8) (12.4) (13.0) (13.5) (14.1) (14.6) (15.3) (16.0) (16.3)

Porting
SAE O-Ring & NPTF

Manifold
2x
31.75
(1.250)

32.26
(1.270)

32.26
(1.270)

2x
22.86
(.900)

63.50
(2.500)

A
45.72
(1.800)

B
22.86
(.900)

45.72
(1.800)
4x
5/16-18 UNC-28
x 12.7 (.50) Min Full thd
28.58
(1.125)

7/8-14 SAE O-Ring

or 1/2-14 NPTF Ports

2x
14.28
(.562)

48.26
(1.900)

Consult Factory for

ISO6149 Porting
PSLGC.PM6, dg, ki

13

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Dimensional Data

T
A
S
E
R
I
E
S

Mounting

Shaft

Inch equivalents for metric dimensions are shown in (**)

44.70 (1.760)
19.00 (.748)
Key 1/4 x 1 Woodruff
14.2 (.56)

27.97 (1.101)
48.26
(1.900)

2.54 (.100)

25.40 (1.000)
1/4-20 UNC thd
x 15.75 (.62) Min Deep

82.52
(3.249)

1" Key

2 x 13.494 (17/32) Thru

On 106.38 (4.188) BC
44.70 (1.760)

SAE A 2 Bolt

25.4 (1.00) Min Full

Spline SAE 6B
4.32 (.170)
1.25 (.049)
23.52 (.926)

1/4-20 UNC thd

x 15.75 (.62) Min Deep

48.26 (1.900)

1" 6B Spline
45

2.54 (.100)

44.42 (1.749)
44.70 (1.760)

4 x 3/8-16 UNC thd

x 12.7 (.50) Min Deep
On 82.55 (3.250) BC

4 Bolt

30.7 (1.21)

25.40 (1.000)
9.70 (.382)
Thru

1" Straight Shaft w/ .38 Cross Hole

PSLGC.PM6, dg, ki

14

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TA Series

Catalog 1510-20

Ordering Information

TA

XXXX

Series

Displacement

Mounting

Code
A
F

XX

Porting

SAE "A" 2 Bolt

4 Bolt

Code Displacement
2.7
3.0
4.0
5.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.6
24.0

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Options

Standard

Shaft

09
10
11

P
M
S

Rotation

XXXX

Code Rotation

Code

0045
0050
0065
0080
0100
0130
0165
0195
0230
0260
0295
0330
0365
0390

Shaft

Mounting

Code

1" Straight w/ 0.38" Crosshole

1" Keyed
1" 6B Spline

Porting
1/2"-14 NPTF
Manifold
7/8"-14 SAE O-Ring

Code
AAAA
AAAB
AAAC
AAAG
AAAH
AABJ*
AABK*
AAFC
AAHD
HAAA**
HAAB**
HAAC**

Options
Black Paint
No Paint
Double Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
White Epoxy Paint
White Epoxy Paint, Viton Seals
External Relief Valve (1894-1), Black Paint
External Relief Valve (1894-1), No Paint
External Relief Valve (1894-1), No Paint, Viton Seals

Not applicable to TA0365 or TA0390 displacements

**

Available only with porting code "M"

PSLGC.PM6, dg, ki

15

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
A
S
E
R
I
E
S

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Technical Information

A General Purpose Motor With

Advanced Technology
Features are built into this multi-purposed motor that
assure long, trouble free life. The power element
contains roller vanes. Splines and seals are cooled.
The drivetrain utilizes patented spline geometry.
This all adds up to a TB Series motor that provides
real value.

T
B
S
E
R
I
E
S

Options

Features

All Common 1 inch, 25mm or 7/8 inch 13 Tooth

Shafts

Roller Vane Power Element For High Volumetric Efficiency and Long Life

SAE A 2 Bolt, 4 Bolt Magneto or 4 Bolt Mounting

Orbiting Commutator For Accurate Timing,

Smooth Low Speed Operation

SAE O-Ring, NPTF, Manifold or BSPF Porting

Full Flow Spline Lubrication For Extended

Spline Life

Front or Rear Porting

External Cross - Over Relief Valve Package

High Pressure Shaft Seal For High Back

Pressure Operation Without External Drain Lines

Free Running Rotor Set

High Flow Shaft seal Cooling For Long Seal

Life

Reverse Timed Manifold

Corrosion Resistance

60:40 Spline Geometry For Superior Powertrain Strength, Long Life

TB Specifications
Code
Displacement

0045 0050
cc/rev
(cu in/rev)

Maximum Speed (rpm) @

Maximum Continuous Flow
Pressure Differential
Maximum Continuous

bar
(psid)
Maximum Intermittent
bar
(psid)

0065 0080 0100 0130 0165 0195 0230 0260

45
(2.7)

49
(3.0)

65
(4.0)

82
(5.0)

99
(6.0)

130
(8.0)

163
(9.9)

785

678

511

409

454

343

274

124.1 124.1 124.1 124.1

(1800) (1800) (1800) (1800)
165.5 165.5 165.5 165.5
(2400) (2400) (2400) (2400)

124.1
(1800)
165.5
(2400)

195
228
260
(11.9) (13.9) (15.9)

230

197

172

0295 0330 0365

0390

293
328
370
(17.9) (20.0) (22.6)

392
(24.0)

153

137

117

114

124.1 124.1 124.1 103.4 100.0

96.6
93.1
86.2
82.8
(1800) (1800) (1800) (1500) (1450) (1400) (1350) (1250) (1200)
165.5 155.2 144.8 137.9 131.0 124.1 113.8 105.2 100.0
(2400) (2250) (2100) (2000) (1900) (1800) (1650) (1525) (1450)

Max. Torque @ Max.Continuous

Pressure
nm
(lb-in)

64.3
(569)

78.3 106.9 134.8 159.4 220.4 273.2 340.2 316.0 349.8 383.1 413.2 440.3 428.4
(693) (946) (1193) (1411) (1951) (2418) (3011) (2797) (3096) (3391) (3657) (3897) (3792)

Max. Torque @ Max.Intermittent

Pressure
nm
(lb-in)

88.0
(779)

106.9 145.1 183.5 216.6 297.4 345.9 399.6 427.3 465.1 498.8 509.0 540.4 524.5
(946) (1284) (1624) (1917) (2632) (3062) (3537) (3782) (4117) (4415) (4505) (4783) (4642)

PSLGC.PM6, dg, ki

16

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Technical Information

Maximum Side Load Capacity

Performance Data
Continuous / Intermittent* Operation

Shaft Side Load - kg (lbs)

907
(2000)

Continuous

680
(1500)

Intermittent*

*Intermittent operation is defined as less

than 10% of each minute.
454
(1000)

Performance data based on testing using 10W40 oil

with a viscosity of 200 SUS at 54 C (130 F.)
227
(500)

Performance data is typical. Actual data may vary

slightly from one production motor to another.

0
-50.8
(-2)

-25.4
(-1)

0
(0)

25.4
(1)

50.8
(2)

76.2
(3)

101.6
(4)

Distance from Mounting Face - mm (in)

Application of the above uni-directional radial loads will result in a

B-10 life of 2.5 million revolutions. For B-10 life at other radial
loads, apply the factors from the curve below.

B-10 Life Factors

4
3
Multiply
Allowable
Radial Load 2
By These
Factors
1
0

0 2 4 6 8 10 12
Life In Millions Of Revolutions

PSLGC.PM6, dg, ki

17

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
B
S
E
R
I
E
S

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Performance Data
Code 0045

Code 0050

45 cc / rev

50 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 124.1 137.9 165.5

T
B
S
E
R
I
E
S

PRESSURE (BAR)
34.5 69.0 103.4 124.1 137.9 165.5

1.9

13.1 29.7
31
17

1.9

16.3 36.0
26
13

3.8

14.0 31.2 48.2 58.5 65.4 79.8

76
61
43
36
29
18

3.8

17.4 38.2 58.5 70.6 78.7 94.9

65
50
35
28
21
9

7.6

15.1 33.2 51.2 61.8 68.8 82.6

167 149 131 121 113
97

7.6

18.4 40.7 62.7 75.8 84.3 101.2

141 127 110 102
94
80

11.4

14.9 33.1 51.4 62.5 69.7 84.3

256 239 220 210 200 183

11.4

18.2 40.4 62.9 76.3 85.1 102.5

218 203 186 177 169 153

15.1

14.9 33.4 52.5 64.1 71.7 86.9

344 326 307 295 285 268

15.1

18.1 40.8 64.1 78.1 87.4 105.9

295 279 261 251 243 227

18.9

14.5 33.2 52.5 64.3 72.2 88.0

433 414 393 380 370 352

18.9

17.5 40.4 63.9 78.3 87.8 106.9

371 355 337 326 317 301

26.5

13.2 32.1 51.7 63.7 71.7 88.0

609 589 566 551 540 520

26.5

16.2 39.1 63.0 77.5 87.2 106.9

525 507 487 474 466 448

34.1

12.1 31.1 50.7 62.7 70.8 87.0

785 764 739 722 710 689

34.1

15.0 38.0 61.7 76.3 86.0 105.7

678 658 638 623 614 595

Flow (LPM)

Flow (LPM)

TORQUE
SPEED

(nm)
(RPM)

62.7
722

2.7 cu in / rev PRESSURE (PSI)

3.0 cu in / revPRESSURE (PSI)

500 1000 1500 1800 2000 2400

.5

116
31

263
17

124
76

276
61

427
43

518
36

579
29

134
167

294
149

453
131

547
121

132
256

293
239

455
220

132
344

296
326

128
433

7
9

500 1000 1500 1800 2000 2400

.5

144
26

319
13

706
18

154
65

338
50

518
35

625
28

697
21

840
9

609
113

731
97

163
141

360
127

555
110

671
102

746
94

896
80

553
210

617
200

746
183

161
218

358
203

557
186

675
177

753
169

907
153

465
307

567
295

635
285

769
268

160
295

361
279

567
261

691
251

774
243

937
227

294
414

465
393

569
380

639
370

779
352

155
371

358
355

566
337

693
326

777
317

946
301

117
609

284
589

458
566

564
551

635
540

779
520

143
525

346
507

558
487

686
474

772
466

946
448

107
785

275
764

449
739

555
722

627
710

770
689

133
678

336
658

546
638

675
623

761
614

936
595

Flow (GPM)

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

555
722
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

18

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Performance Data
Code 0065

Code 0080

65 cc / rev

80 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 124.1 137.9 165.5

PRESSURE (BAR)
34.5 69.0 103.4 124.1 137.9 165.5

1.9

24.1 51.9 80.1

22
14
6

1.9

28.9 63.5 99.1

17
10
4

3.8

25.3 54.1 82.9 100.2 111.7 134.8

51
42
34
29
25
17

3.8

30.4 66.1 102.2 123.9 138.5 168.0

40
33
26
21
18
10

7.6

26.3 56.5 86.7 104.6 116.7 140.5

108
99
90
85
81
71

7.6

32.2 69.6 107.3 129.9 145.0 175.1

86
78
70
66
62
53

11.4

26.1 56.3 86.9 105.3 117.4 141.5

166 156 147 141 136 126

11.4

32.2 69.9 108.3 131.4 146.6 176.9

132 124 116 110 106
97

15.1

25.9 56.6 87.9 106.8 119.3 144.4

224 214 203 197 192 181

15.1

32.3 71.0 110.3 134.1 149.9 181.7

178 170 161 155 151 141

18.9

25.2 56.2 87.8 106.9 119.5 145.1

281 271 260 252 247 237

18.9

31.9 70.8 110.6 134.8 150.8 183.1

225 216 206 200 196 185

26.5

23.3 54.3 86.3 105.7 118.6 144.6

396 385 372 364 359 347

26.5

30.2 69.5 109.8 134.3 150.6 183.5

317 307 296 290 285 274

34.1

21.7 52.8 84.6 103.9 116.9 143.1

511 499 485 476 470 457

34.1

28.5 67.8 108.0 132.5 148.9 181.8

409 398 387 379 374 362

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

116.9
470

4.0 cu in / rev PRESSURE (PSI)

5.0 cu in / rev PRESSURE (PSI)

500 1000 1500 1800 2000 2400

.5

213
22

459
14

709
6

224
51

479
42

734
34

887
29

233
108

500
99

231
166

500 1000 1500 1800 2000 2400

.5

256
17

562
10

877
4

989 1193
25
17

269
40

585
33

905 1097 1226 1487

26
21
18
10

767
90

926 1033 1244

85
81
71

285
86

616
78

950 1150 1283 1550

70
66
62
53

498
156

769
147

932 1039 1252

141 136 126

285
132

619
124

959 1163 1298 1566

116 110 106
97

229
224

501
214

778
203

945 1056 1278

197 192 181

286
178

628
170

976 1187 1327 1608

161 155 151 141

223
281

497
271

777
260

946 1058 1284

252 247 237

282
225

627
216

979 1193 1335 1621

206 200 196 185

206
396

481
385

764
372

936 1050 1280

364 359 347

267
317

615
307

972 1189 1333 1624

296 290 285 274

192
511

467
499

749
485

920 1035 1267

476 470 457

252
409

600
398

956 1173 1318 1609

387 379 374 362

Flow (GPM)

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

1035
470
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

19

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
B
S
E
R
I
E
S

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Performance Data
Code 0100

Code 0130

100 cc / rev

130 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 124.1 137.9 165.5

T
B
S
E
R
I
E
S

PRESSURE (BAR)
34.5 69.0 103.4 124.1 137.9 165.5

1.9

35.0 75.6 116.9 142.1 159.1

16
13
9
7
5

1.9

50.4 107.9 167.1 203.0 227.2

12
10
7
5
3

3.8

37.3 78.7 121.2 146.6 163.6 196.2

35
32
27
25
23
18

3.8

52.5 111.7 171.2 206.9 230.8 278.9

27
24
21
19
17
13

7.6

39.1 82.7 126.7 152.9 170.5 205.8

73
69
64
61
59
53

7.6

54.3 115.6 177.5 214.8 239.5 289.0

55
52
49
46
44
40

11.4

39.0 83.0 128.1 154.9 172.9 208.3

111 107 102
98
95
89

11.4

54.5 116.3 178.6 216.0 241.0 290.4

84
81
77
74
72
67

15.1

39.2 84.4 130.8 158.5 177.3 213.8

149 144 139 135 132 126

15.1

54.6 117.7 181.3 219.2 244.5 294.7

113 109 105 102 100
95

18.9

38.8 84.7 131.5 159.4 178.3 215.7

187 182 176 172 169 162

18.9

54.0 117.6 181.9 220.4 246.2 297.4

142 138 133 130 128 122

26.5

36.9 83.4 130.9 159.4 178.5 216.6

264 257 250 246 242 235

26.5

50.8 115.1 180.4 219.5 245.6 297.4

199 195 190 186 184 177

34.1

34.0 80.8 128.7 157.6 176.9 215.7

340 333 325 319 316 307

34.1

46.8 111.2 176.6 215.9 242.3 295.1

257 252 246 242 239 233

45.4

29.0 75.6 123.3 152.2 171.5 210.5

454 446 437 430 426 417

45.4

37.8 102.5 168.2 208.1 234.5 288.1

343 338 331 327 323 316

56.8

28.6 92.4 157.4 196.6 223.0 276.0

430 424 416 411 407 399

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

171.5
426

Flow (LPM)

6.0 cu in / rev PRESSURE (PSI)

8.0 cu in / rev PRESSURE (PSI)

500 1000 1500 1800 2000 2400

.5

310
16

669 1035 1258 1408

13
9
7
5

330
35

500 1000 1500 1800 2000 2400

.5

446
12

955 1479 1797 2011

10
7
5
3

697 1073 1298 1448 1737

32
27
25
23
18

465
27

989 1515 1831 2043 2469

24
21
19
17
13

346
73

732 1121 1353 1509 1822

69
64
61
59
53

481 1023 1571 1901 2120 2558

55
52
49
46
44
40

345
111

735 1134 1371 1530 1844

107 102
98
95
89

482 1029 1581 1912 2133 2570

84
81
77
74
72
67

347
149

747 1158 1403 1569 1892

144 139 135 132 126

483 1042 1605 1940 2164 2608

113 109 105 102 100
95

343
187

750 1164 1411 1578 1909

182 176 172 169 162

478 1041 1610 1951 2179 2632

142 138 133 130 128 122

327
264

738 1159 1411 1580 1917

257 250 246 242 235

450 1019 1597 1943 2174 2632

199 195 190 186 184 177

301
340

715 1139 1395 1566 1909

333 325 319 316 307

414
257

984 1563 1911 2145 2612

252 246 242 239 233

12

257
454

669 1091 1347 1518 1863

446 437 430 426 417

12

335
343

907 1489 1842 2076 2550

338 331 327 323 316

15

253
430

818 1393 1740 1974 2443

424 416 411 407 399

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

1518
426

Flow (GPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.
PSLGC.PM6, dg, ki

20

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Performance Data
Code 0165

Code 0195

165 cc / rev

195 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 124.1 155.2

PRESSURE (BAR)
34.5 69.0 103.4 124.1 144.8

1.9

59.8 128.5 199.9 242.8

9
7
4
3

1.9

77.7 168.3 263.1 321.0 378.8

9
8
7
6
5

3.8

62.8 133.4 205.5 248.7 313.6

21
18
15
13
9

3.8

81.1 173.7 268.9 326.5 384.4

18
17
16
15
14

7.6

65.5 139.9 215.7 261.4 329.0

44
40
37
34
29

7.6

84.3 178.5 276.0 334.6 393.2

38
36
35
33
32

11.4

66.0 141.0 217.6 263.5 331.5

67
63
59
56
51

11.4

84.2 179.9 277.0 335.9 394.8

57
55
53
52
50

15.1

66.9 144.2 222.3 269.1 338.9

90
86
82
78
73

15.1

84.3 181.6 280.4 339.8 398.6

76
74
72
71
69

18.9

66.4 145.0 224.6 272.5 344.1

113 109 104 101
95

18.9

83.3 180.9 280.2 340.2 399.6

95
93
91
89
87

26.5

63.3 143.3 224.5 273.2 345.9

159 154 149 145 139

26.5

78.7 177.6 277.4 337.4 397.0

134 131 129 127 125

34.1

58.4 139.0 221.1 270.4 344.3

205 200 194 190 183

34.1

72.4 170.6 270.9 331.5 392.3

172 169 167 164 162

45.4

48.0 128.9 211.7 261.8 336.7

274 268 262 257 250

45.4

59.9 157.2 257.9 318.7 379.6

230 227 223 221 217

56.8

36.3 116.7 198.7 248.2 323.0

343 337 330 325 317

56.8

45.1 141.5 240.6 300.8 361.5

287 284 280 277 273

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

248.2
325

11.9 cu in / rev

9.9 cu in / revPRESSURE (PSI)

PRESSURE (PSI)
500 1000 1500 1800 2100

500 1000 1500 1800 2250

.5

529 1137 1769 2149

9
7
4
3

.5

688 1490 2329 2841 3353

9
8
7
6
5

556 1181 1819 2201 2776

21
18
15
13
9

718 1537 2380 2890 3402

18
17
16
15
14

580 1238 1909 2314 2912

44
40
37
34
29

746 1580 2443 2962 3480

38
36
35
33
32

584 1248 1926 2332 2934

67
63
59
56
51

745 1592 2452 2973 3494

57
55
53
52
50

592 1276 1968 2382 3000

90
86
82
78
73

746 1607 2482 3008 3528

76
74
72
71
69

588 1283 1988 2412 3046

113 109 104 101
95

737 1601 2480 3011 3537

95
93
91
89
87

560 1268 1987 2418 3062

159 154 149 145 139

697 1572 2455 2986 3514

134 131 129 127 125

517 1230 1957 2393 3047

205 200 194 190 183

641 1510 2398 2934 3472

172 169 167 164 162

12

425 1141 1874 2317 2980

274 268 262 257 250

12

530 1391 2283 2821 3360

230 227 223 221 217

15

321 1033 1759 2197 2859

343 337 330 325 317

15

399 1252 2130 2662 3200

287 284 280 277 273

Flow (GPM)

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

1759
330

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

21

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
B
S
E
R
I
E
S

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Performance Data
Code 0230

Code 0260

Code 0295

230 cc / rev

260 cc / rev

295 cc / rev

PRESSURE (BAR)

T
B
S
E
R
I
E
S

PRESSURE (BAR)

PRESSURE (BAR)

34.5 69.0 103.4 137.9

34.5 69.0 100.0 131.0

34.5 69.0 96.6 124.1

1.9

89.9 192.5 298.3 406.4

8
7
6
5

1.9

102.4 220.0 328.8 440.2

7
6
5
4

117.4 251.8 362.4 474.5

6
5
4
3

3.8

92.4 195.8 302.9 412.3

16
15
14
13

224.2 334.9 447.1

3.8 105.3
14
13
12
11

257.7 368.9 479.9

3.8 120.8
12
11
10
9

7.6

94.9 200.5 308.7 418.0

32
31
30
28

229.6 341.8 455.5

7.6 108.2
28
27
26
24

263.5 377.0 490.7

7.6 124.1
25
24
22
20

11.4

95.5 202.1 310.7 420.9

49
47
46
43

231.3 344.0 457.8

11.4 108.6
43
41
40
38

264.8 378.8 492.1

11.4 124.3
38
36
35
32

15.1

95.8 205.1 315.1 425.0

65
64
62
59

234.3 348.7 463.0

15.1 108.8
57
56
54
52

267.3 382.6 496.9

15.1 124.1
50
49
47
44

18.9

94.9 204.8 316.0 427.3

82
80
78
74

234.3 349.8 465.1

18.9 107.8
71
70
68
65

266.7 383.1 498.8

18.9 122.7
63
61
60
57

26.5

90.3 202.2 314.6 426.6

114 112 110 106

231.5 348.4 464.6

26.5 102.7
100
99
96
93

262.7 379.7 496.4

26.5 116.8
89
87
85
81

34.1

83.7 196.4 309.3 422.7

147 145 142 138

34.1

95.4 224.9 342.6 459.8

129 127 125 121

254.2 372.3 490.0

34.1 107.9
114 112 109 106

45.4

69.3 182.5 296.7 411.8

197 194 190 185

45.4

78.6 209.1 328.0 446.6

172 170 167 162

45.4

89.5 235.6 354.9 473.8

153 150 147 142

56.8

53.4 185.6 277.6 391.7

246 243 239 233

56.8

61.0 190.1 306.3 424.0

216 213 209 204

56.8

68.5 212.3 328.5 446.8

191 188 185 180

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

1.9

Flow (LPM)

277.6
239

15.9 cu in / rev

13.9 cu in / rev
PRESSURE (PSI)

17.9 cu in / rev
PRESSURE (PSI)

PRESSURE (PSI)
500 1000 1450 1900

500 1000 1500 2000

500 1000 1400 1800

.5

796 1704 2640 3597

8
7
6
5

.5

906 1947 2910 3896

7
6
5
4

.5

1039 2229 3208 4200

6
5
4
3

818 1733 2681 3649

16
15
14
13

932 1984 2964 3957

14
13
12
11

1069 2281 3265 4248

12
11
10
9

840 1775 2732 3700

32
31
30
28

958 2032 3025 4032

28
27
26
24

1098 2332 3337 4343

25
24
22
20

845 1789 2750 3725

49
47
46
43

961 2047 3045 4052

43
41
40
38

1100 2344 3353 4356

38
36
35
32

848 1815 2789 3762

65
64
62
59

963 2074 3086 4098

57
56
54
52

1098 2366 3386 4398

50
49
47
44

840 1813 2797 3782

82
80
78
74

954 2074 3096 4117

71
70
68
65

1086 2361 3391 4415

63
61
60
57

799 1790 2785 3776

114 112 110 106

909 2049 3084 4112

100
99
96
93

1034 2325 3361 4394

89
87
85
81

741 1738 2738 3741

147 145 142 138

844 1991 3032 4070

129 127 125 121

955 2250 3295 4337

114 112 109 106

12

613 1615 2626 3645

197 194 190 185

12

696 1851 2903 3953

172 170 167 162

12

792 2085 3141 4194

153 150 147 142

15

473 1643 2457 3467

246 243 239 233

15

540 1683 2711 3753

216 213 209 204

15

606 1879 2908 3955

191 188 185 180

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

2457
239

Flow (GPM)

Flow (GPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

22

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Performance Data
Code 0330

Code 0365

Code 0390

330 cc / rev

370 cc / rev

390 cc / rev

PRESSURE (BAR)
34.5 69.0 93.1 113.8

PRESSURE (BAR)
34.5 69.0 82.8 100.0

PRESSURE (BAR)
34.5 69.0 86.2 105.2

1.9 134.7 282.2 387.0 477.6

1.9 157.45 332.44 421.94 521.63

1.9 147.94 325.93 399.32 492.52

3.8 138.3 288.7 394.9 485.7

339.5 428.9 527.8

3.8 163.1
10
9
9
8

3.8 154.69 333.18 405.57 496.46

7.6 141.8 296.0 404.6 497.8

349.1 439.5 538.8

7.6 168.8
20
19
18
17

342.1 416.1 510.2

7.6 160.1
18
17
16
15

11.4 142.2 297.5 406.4 499.8

348.2 438.7 538.3

11.4 167.8
30
29
28
27

345.5 419.6 512.9

11.4 161.2
28
26
26
24

15.1 142.1 301.2 411.8 506.2

349.0 440.3 540.4

15.1 166.9
40
39
38
36

350.5 425.3 519.1

15.1 163.0
37
36
35
34

18.9 140.4 301.1 413.2 509.0

347.4 439.2 539.5

18.9 164.0
50
49
48
46

352.5 428.2 523.1

18.9 162.6
47
45
45
43

26.5 134.0 296.8 410.6 507.5

340.0 432.3 533.2

26.5 154.9
70
69
67
65

351.4 428.4 524.5

26.5 157.3
66
65
64
62

34.1 123.4 287.4 402.5 500.6

94

327.5 420.4 522.1

34.1 142.4
90
89
87
85

343.5 421.6 519.4

34.1 146.5
85
84
83
81

45.4 102.2 267.0 383.1 482.3

137 134 131 127

300.3 394.1 496.3

45.4 113.2
121 119 117 115

320.3 400.1 499.1

45.4 122.8
114 112 111 110

56.8

56.8

11

10

22

21

34

32

45

43

56

55

79

102

77

100

20
31
42
53
75

97

18
29
40
51
73

78.2 240.5 354.3 452.0

171 168 165 161

Flow (LPM)

79.1 266.1 360.4 462.7

151 149 147 144

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

56.8

93.9 290.5 369.7 468.3

143 141 140 138

Flow (LPM)

354.3
165

20.0 cuPRESSURE
in / rev
(PSI)

22.6 cu
in / rev
PRESSURE (PSI)

500 1000 1350 1650

24.0 cuPRESSURE
in / rev
(PSI)

500 1000 1250 1525

500 1000 1200 1450

.5

1192 2498 3425 4227

5
4
4
3

.5

1393 2942 3734 4617

5
4
4
3

.5

1309 2885 3534 4359

4
3
2
2

1224 2555 3495 4299

11
10
9
8

1444 3005 3796 4672

10
9
9
8

1368 2948 3589 4394

9
8
7
6

1255 2620 3581 4406

22
21
20
18

1494 3090 3890 4769

20
19
18
17

1417 3028 3683 4516

18
17
16
15

1259 2633 3597 4424

34
32
31
29

1485 3082 3883 4765

30
29
28
27

1427 3058 3714 4540

28
26
26
24

1258 2666 3645 4480

45
43
42
40

1477 3089 3897 4783

40
39
38
36

1443 3102 3764 4595

37
36
35
34

1243 2665 3657 4505

56
55
53
51

1452 3075 3887 4775

50
49
48
46

1439 3120 3790 4630

47
45
45
43

1186 2627 3634 4492

79
77
75
73

1371 3009 3826 4719

70
69
67
65

1392 3110 3792 4642

66
65
64
62

1092 2544 3563 4431

102 100
97
94

1260 2899 3721 4621

90
89
87
85

1297 3040 3732 4597

85
84
83
81

12

905 2363 3391 4269

137 134 131 127

12

1002 2658 3488 4393

121 119 117 115

12

1087 2835 3541 4418

114 112 111 110

15

692 2129 3136 4001

171 168 165 161

15

700 2355 3190 4095

151 149 147 144

15

831 2571 3272 4145

143 141 140 138

Flow (GPM)

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

3136
165

Flow (GPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

23

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
B
S
E
R
I
E
S

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Dimensional Data

Dimensions
Inch equivalents for metric dimensions are shown in (**)
"L"

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to
turn Clockwise, "B" to turn
Counterclockwise.
Rear Ports - Pressurize "A" to
turn Counterclockwise, "B" to
turn Clockwise.

95.5
(3.76)
Max.

Length "L" and Weight

Displacement Code

0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390

SAE "A" Mount

T
B

mm

Length "L"

(inches)
kg

Weight

(lb)

136 138
141 144 147 154 160 166 173
179
185 192
200 205
(5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29)(6.54) (6.79) (7.04) (7.29)(7.54) (7.88) (8.04)
6.03 6.12 6.26 6.35 6.49 6.76 7.03 7.35 7.58 7.80 8.07 8.35 8.66 8.80
(13.3) (13.5) (13.8) (14.0) (14.3) (14.9) (15.5)(16.2) (16.7) (17.2) (17.8)(18.4) (19.1) (19.4)

4 Bolt

S
E
R
I
E
S

mm
Length "L"

(inches)
kg

Weight

(lb)

136 138
141 144 147 154 160 166 173
179
185 192
200 205
(5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29)(6.54) (6.79) (7.04) (7.29)(7.54) (7.88) (8.05)
5.62 5.67 5.80 5.94 6.08 6.31 6.62 7.03 7.17 7.39 7.62 7.94 8.26 8.39
(12.4) (12.5) (12.8) (13.1) (13.4) (13.9) (14.6)(15.5) (15.8) (16.3) (16.8)(17.5) (18.2) (18.5)

Magneto Mount
Length "L"

mm
(inches)
kg

Weight

(lb)

136 138
141 144 147 154 160 166 173
179
185 192
(5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29)(6.54) (6.79) (7.04) (7.29) 7.54

200 205
7.88 8.05

6.30 6.40 6.53 6.62 6.76 7.03 7.30 7.62 7.85 8.12 8.35 8.62 8.94 9.07
(13.9) (14.1) (14.4) (14.6) (14.9) (15.5) (16.1)(16.8) (17.3) (17.9) (18.4)(19.0) (19.7) (20.0)

Mounting
SAE A 2 Bolt

Magneto

14.2 (.56)
2.54 (.100)

14.2 (.56)

45
22 30'

2.54 (.100)

82.52 (3.249)

82.52 (3.249)

2 x 13.494 (17/32) Thru On

a 106.38 (4.188) BC

4 x 13.494 (17/32)
Thru on a 106.38 (4.188) BC

PSLGC.PM6, dg, ki

24

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Dimensional Data

Mounting

48.26 (1.900)

Inch equivalents for metric dimensions are shown in (**)

45
2.54 (.100)

4 Bolt
44.42 (1.749)

4 x 3/8-16 UNC thd Thru

On 82.55 (3.250) BC

14.2 (.56)

Porting

2.54 (.100)
48.26 (1.900)
2 x 13.494 (17/32) Thru
on a 106.38 (4.188) BC

48.26 (1.900)

45.72 (1.800)

SAE O-Ring, NPTF, BSPF

82.52 (3.249)

2 x 22.86
(.900)

7/8-14 SAE O-Ring

or
1/2-14 NPTF
or
1/2 BSPF

14.2 (.56)
2.54 (.100)
48.26 (1.900)

48.26 (1.900)
63.50 (2.500)

82.52 (3.249)

Manifold
4 x 5/16-18 UNC-2B
x 12.7 (.50) Min Full thd

2x
31.75 (1.250)
28.58 (1.125)

2 x 14.28 (.562)

2x
22.86 (.900)

2 x 13.494 (17/32) Thru on

a 106.38 (4.188) BC

45.72 (1.800)

L + 20.3 (.80)

16.26 (.640)

Rear, SAE O-Ring

A
B

Consult Factory for

ISO6149 Porting

3/4-16 UNF Straight

thd O-Ring Ports
24.41 (.961)

31.06 (1.223)

PSLGC.PM6, dg, ki

25

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
B
S
E
R
I
E
S

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Dimensional Data

Shaft
Inch equivalents for metric dimensions are shown in (**)
49.02 (1.93)
44.70 (1.760)
19.00 (.748)

M8 x 1.25-6H thd
x .75 Min Deep
27.86 (1.097)
To Top of Key

Key 1/4 x 1 Woodruff

27.97 (1.101)

25.001 (.9843)

25.000 (.9995)
1/4-20 UNC thd
x 15.75 (.62) Min Deep

Key A8 x 7 x 23mm

1" Key
25mm Keyed

T
B
S
E
R
I
E
S

49.3 (1.94)
4.32 (.170)
1.24 (.049)
19.00 (.748)
23.52 27.97
(.926) (1.101)

61.2 (2.41)
4.06
(.16)

25.40 (1.000)
25.65 (1.010) x 1/4 Key

25.65 (1.010)
x 6.363 (.2505)
3/4-16 UNF thd
Torque Nut To 300-237 Nm
(225-175 ft lbs)

Long 1" Key

44.7 (1.76)

34.5 (1.36)

125.00 .15 Taper per Meter

(1.500 .006 Taper per Ft)
25.387 (.9995)

25.4 (1.00) Min Full

Spline SAE 6B
4.3 (.17)
1.24 (.049)

1" Tapered

23.52 (.926)

1/4-20 UNC thd

x 15.75 (.62) Min Deep

1" 6B Spline

44.7 (1.76)
30.7 (1.21)

41.4 (1.63)

14.2 (.56) Min Full Spline

25.387 (.9995)
9.72 (.383)
Thru

18.03 (.710)

1" Straight Shaft w/ .38 Cross Hole

7/8" 13 Tooth Spline
PSLGC.PM6, dg, ki

26

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TB Series

Catalog 1510-20

Ordering Information

TB

XXXX

XX

Series

Displacement

Mounting

Porting

Shaft

Code

Mounting

Code

A
F
M

SAE "A" 2 Bolt

4 Bolt
Magneto

0
1

Code
09
10
11
13
21
25
26
28

Code Displacement
0045
0050
0065
0080
0100
0130
0165
0195
0230
0260
0295
0330
0365
0390

2.7
3.0
4.0
5.0
6.0
8.0
9.9
11.9
13.9
15.9
17.9
20.0
22.6
24.0

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

Code
M
P*
R
S
T**
*
**

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Manifold
1/2"-14 NPTF
Rear; 3/4-16 SAE O-Ring
7/8"-14 SAE O-Ring
1/2" BSPF

Available on A & F mounting only

Available on A & M mounting only

XXXX

Rotation

Options

Rotation
Standard
Reverse Timed Manifold

Shaft

T
B

1" Straight w/0.38" Crosshole

1" Keyed
1" 6B Spline
Long 1" Keyed
1" Keyed; Corrosion Resistant
1" Tapered
25mm Keyed w/ 8mm Key
7/8" 13 Tooth Spline

Code

Porting

AAAA
AAAB
AAAC
AAAF
AABP
AAAG
AAAH
AAAJ
AAFG
AABJ*
AABK*
AABL*
AABM*
AAFC
AAHD
AAJV
HAAA**
HAAB**
HAAC**

S
E
R
I
E
S

Options
Black Paint
No Paint
Double Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
White Epoxy Paint
White Epoxy Paint, Viton Seals
Bidirectional Shuttle (3:30), Black Paint
External Relief Valve (1894-1), Black Paint
External Relief Valve (1894-1), No Paint
External Relief Valve (1894-1), No Paint, Viton Seals

Not applicable to TB0365 or TB0390 displacements

**

Available only with porting code "M"

PSLGC.PM6, dg, ki

27

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Technical Information

The Ultimate In Performance From

A Small Frame Motor
Parkers TD Series motor provides all that could be
expected of a general purpose motor and more.
Patented 60:40 spline geometry provides drivetrain
strength for severe applications. Roller vanes and
sealed orbit commutation assure high volumetric
efficiency and smooth low speed operation. Cooling
fluid flow across splines and seals mean long,
trouble free life.

Options

Features

All Common 1 inch, 25mm or 7/8 inch 13 Tooth

Shafts

Roller Vane Power Element For High Volumetric Efficiency and Long Life

SAE A 2 Bolt, 4 Bolt Magneto or 4 Bolt Mounting

Orbiting Commutator For Accurate Timing,

Smooth Low Speed Operation

Wheel Mount

Full Flow Spline Lubrication For Extended

Spline Life

SAE O-Ring, NPTF, Manifold or BSPF Porting

Front or Rear Porting

High Pressure Shaft Seal For High Back

Pressure Operation Without External Drain Lines

Speed Sensor

High Flow Shaft Seal Cooling For Long Seal

Life

External Cross - Over Relief Valve Package

Free Running Rotor Set

60:40 Spline Geometry For Superior Powertrain Strength, Long Life

Reverse Timed Manifold

T
D

Corrosion Resistance

S
E
R
I
E
S

Code

TD Specifications

Displacement

0045 0050 0065

cc/rev
(cu in/rev)

45
(2.7)

50
(3.0)

66
(4.0)

82
(5.0)

98
(6.0)

805

640

654

546

456

Maximum Speed (rpm) @

Maximum Continuous Flow
Pressure Differential
Maximum Continuous
Maximum Intermittent

0080 0100 0130 0165 0195

130
163
196
(8.0) (10.0) (11.9)

344

274

230

0230 0260 0295 0330 0365

0390

228
261
293
326
370
392
(13.9) (15.9) (17.9) (20.0) (22.6) (24.0)

247

215

192

171

146

143

bar
(psid)

137.9 137.9 137.9 137.9 137.9 137.9 137.9 137.9 120.7 113.8 106.9 100.0 91.4
86.2
(2000) (2000) (2000) (2000) (2000) (2000) (2000) (2000) (1750) (1650) (1550) (1450) (1325) (1250)

bar
(psid)

172.4 172.4 172.4 172.4 172.4 172.4 172.4 172.4 148.3 137.9 127.6 117.2 108.6 103.4
(2500) (2500) (2500) (2500) (2500) (2500) (2500) (2500) (2150) (2000) (1850) (1700) (1575) (1500)

Max. Torque @ Max. Continuous

Pressure
nm
(lb-in)
Max. Torque @ Max. Intermittent
Pressure
nm
(lb-in)

70.5
(624)

88.7 122.0 153.5 183.5 248.7 308.7 379.6 370.2 402.3 427.5 443.6 467.6 444.6
(785) (1080) (1359) (1624) (2201) (2732) (3360) (3277) (3561) (3784) (3926) (4139) (3935)

90.0
(797)

112.8 154.2 194.1 231.9 313.6 389.4 476.9 461.0 492.9 515.6 523.2 558.6 538.7
(998) (1365) (1718) (2053) (2776) (3447) (4221) (4080) (4363) (4564) (4631) (4944) (4768)

PSLGC.PM6, dg, ki

28

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Technical Information
Maximum Side Load Capacity
Flange Mount

B-10 Life Factors

4

Shaft Side Load - kg (lbs)

1361
(3000)

3
Multiply
Allowable
Radial Load 2
By These
Factors
1

1021
(2250)

0
0 2 4 6 8 10 12
Life In Millions Of Revolutions
680
(1500)

Performance Data
Continuous / Intermittent* Operation
340
(750)

Continuous
Intermittent*

0
-50.8
(-2)

-25.4
0
25.4
50.8
76.2
(-1)
(0)
(1)
(2)
(3)
Distance From Mounting Face - mm (in)

*Intermittent operation is defined as less

than 10% of each minute.

101.6
(4)

Performance data based on testing using 10W40 oil

with a viscosity of 200 SUS at 54 C (130 F.)

Wheel Mount
Shaft Side Load - kg (lbs)

Performance data is typical. Actual data may vary

slightly from one production motor to another.

1361
(3000)

1021
(2250)

T
D

680
(1500)

S
E
R
I
E
S

340
(750)

0
0
(0)

25.4
(1)

50.8
(2)

76.2
(3)

101.6
(4)

127.0
(5)

Distance From Mounting Face - mm (in)

Application of the above uni-directional radial loads will result in a
B-10 life of 3 million revolutions. For B-10 life at other radial loads,
apply the factors from the curve at top of next column.
PSLGC.PM6, dg, ki

29

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Performance Data
Code 0045

Code 0050

Code 0065

45 cc / rev PRESSURE (BAR)

50 cc / rev

65 cc / rev PRESSURE (BAR)

34.5 69.0 103.4 137.9 172.4

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4

1.9

13.7 30.7 48.0 65.4 83.0

41
35
28
22
14

1.9

16.5 36.9 58.3 79.7

32
23
13
6

1.9

24.9 54.3 83.9 113.4

24
17
11
3

3.8

14.2 31.9 49.7 67.7 85.5

86
79
72
65
56

3.8

18.0 39.0 60.7 82.1 103.3

69
60
50
41
25

3.8

26.2 56.3 86.2 115.8 145.0

52
45
38
31
23

7.6

14.5 32.5 51.1 69.9 89.0

176 168 161 152 141

7.6

19.2 41.1 63.6 86.3 108.6

146 136 124 113
94

7.6

27.0 57.8 89.1 120.4 150.9

109 102
94
85
75

11.4

14.2 32.4 51.2 70.0 89.1

266 257 249 239 227

11.4

18.9 41.0 63.8 86.8 109.5

225 214 203 191 172

11.4

26.9 57.8 89.3 120.7 151.4

167 159 151 141 130

15.1

13.9 32.2 51.3 70.5 89.9

356 346 337 326 313

15.1

19.1 41.5 64.9 88.6 112.2

294 282 271 260 241

15.1

26.8 58.1 89.8 121.8 153.3

224 215 207 197 185

18.9

13.4 31.7 51.0 70.5 90.0

446 435 425 413 398

18.9

18.6 41.2 64.9 88.7 112.8

363 349 339 327 307

18.9

26.3 57.7 89.7 122.0 154.2

279 271 262 252 240

26.5

11.9 30.5 49.7 69.5 89.6

625 613 601 587 570

26.5

17.6 40.3 64.2 88.4 112.6

501 485 474 460 440

26.5

24.4 56.2 88.5 121.1 153.8

386 376 366 356 343

34.1

10.6 29.3 48.6 68.4 88.6

805 791 777 761 742

34.1

15.9 38.6 62.7 87.1 111.6

640 621 609 594 572

34.1

22.0 53.9 86.3 119.1 152.2

494 483 472 460 446

45.4

12.9 35.8 60.0 84.5 109.1

835 813 802 786 766

45.4

17.2 49.1 81.8 114.9 148.5

654 641 629 617 601

56.8

11.5 43.8 87.7 109.5 142.9

802 789 676 763 748

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

68.4
761

2.7 cu in / rev

Flow (LPM)

Flow (LPM)

3.0 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500

T
D
S
E
R
I
E
S

PRESSURE (PSI)
500 1000 1500 2000 2500

.5

121
41

272
35

425
28

579
22

735
14

.5

146
32

327
23

516
13

705
6

126
86

282
79

440
72

599
65

757
56

159
69

345
60

537
50

727
41

128
176

288
168

452
161

619
152

788
141

170
146

364
136

563
124

126
266

287
257

453
249

620
239

789
227

167
225

363
214

123
356

285
346

454
337

624
326

796
313

169
294

119
446

281
435

451
425

624
413

797
398

105
625

270
613

440
601

615
587

793
570

94
805

259
791

430
777

605
761

784
742

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

605
761

34.5 69.0 103.4 137.9 172.4

4.0 cu in /PRESSURE
rev
(PSI)
500 1000 1500 2000 2500

.5

220
24

481
17

743 1004
11
3

914
25

232
52

498
45

763 1025 1283

38
31
23

764
113

961
94

239
109

512
102

789 1066 1336

94
85
75

565
203

768
191

969
172

238
167

512
159

790 1068 1340

151 141 130

367
282

574
271

784
260

993
241

237
224

514
215

795 1078 1357

207 197 185

165
363

365
349

574
339

785
327

998
307

233
279

511
271

794 1080 1365

262 252 240

156
501

357
485

568
474

782
460

997
440

216
386

497
376

783 1072 1361

366 356 343

141
640

342
621

555
609

771
594

988
572

195
494

477
483

764 1054 1347

472 460 446

12

114
835

317
813

531
802

748
786

966
766

12

152
654

435
641

724 1017 1314

629 617 601

15

102
802

388
789

776
676

Flow (GPM)

969 1265
763 748

Flow (GPM)
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

30

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Performance Data
Code 0080

Code 0100

80 cc / rev

100 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4

1.9

29.5 65.0
17
8

1.9

35.6 77.6
14
7

3.8

31.2 67.3 103.7 140.7 178.8

39
30
23
13
2

3.8

37.5 80.2 122.4 165.0

33
26
18
9

7.6

32.8 71.3 110.0 148.0 183.3

85
76
68
56
42

7.6

39.3 84.8 130.2 174.1 214.5

71
64
55
45
33

11.4

32.9 71.5 110.5 149.0 186.9

131 122 113 101
86

11.4

39.5 85.4 131.1 175.8 219.6

109 102
92
83
69

15.1

33.1 72.5 112.4 152.2 190.5

177 167 158 146 130

15.1

39.9 86.8 133.9 180.3 224.8

147 140 130 120 106

18.9

32.8 72.4 112.9 153.5 193.5

223 213 203 191 174

18.9

39.4 87.1 135.2 183.3 229.6

186 178 168 158 143

26.5

30.8 71.0 111.7 152.9 194.1

316 304 293 280 262

26.5

37.3 85.8 134.6 183.5 231.9

263 254 244 232 217

34.1

28.1 68.1 109.1 150.7 192.4

408 396 384 370 350

34.1

34.1 82.6 131.8 181.4 230.7

340 330 319 307 292

45.4

22.3 62.3 103.5 145.4 187.7

546 533 519 504 483

45.4

27.5 75.8 125.5 175.7 225.7

456 444 433 420 403

56.8

15.4 55.8 96.8 138.5 181.0

686 670 655 638 615

56.8

19.9 68.5 117.7 167.7 217.8

572 558 546 533 514

Flow (LPM)
TORQUE
SPEED

Flow (LPM)
(nm)
(RPM)

138.5
638

5.0 cu in / rev

6.0 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500

.5

261
17

575
8

276
39

596
30

290
85

PRESSURE (PSI)
500 1000 1500 2000 2500

.5

315
14

687
7

918 1245 1583

23
13
2

332
33

710 1083 1460

26
18
9

631
76

974 1310 1622

68
56
42

348
71

751 1152 1541 1899

64
55
45
33

291
131

633
122

978 1319 1654

113 101
86

350
109

756 1160 1556 1944

102
92
83
69

293
177

642
167

995 1347 1686

158 146 130

353
147

768 1185 1596 1990

140 130 120 106

290
223

641
213

999 1359 1713

203 191 174

349
186

771 1197 1622 2032

178 168 158 143

273
316

628
304

989 1353 1718

293 280 262

330
263

759 1191 1624 2053

254 244 232 217

249
408

603
396

966 1334 1703

384 370 350

302
340

731 1167 1606 2042

330 319 307 292

12

197
546

551
533

916 1287 1661

519 504 483

12

243
456

671 1111 1555 1998

444 433 420 403

15

136
686

494
670

857 1226 1602

655 638 615

15

176
572

606 1042 1484 1928

558 546 533 514

Flow (GPM)

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

1226
638

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

31

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
D
S
E
R
I
E
S

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Performance Data
Code 0130

Code 0165

130 cc / revPRESSURE (BAR)

165 cc / revPRESSURE (BAR)

34.5 69.0 103.4 137.9 172.4

34.5 69.0 103.4 137.9 172.4

1.9

50.3 108.7 168.1 228.0

12
10
7
3

1.9

62.4 132.8 204.8 277.6

9
7
4
3

3.8

52.4 112.5 172.3 231.7 291.1

27
24
21
17
10

3.8

64.9 137.0 209.7 282.3 355.9

21
18
16
12
8

7.6

54.5 116.6 179.0 241.3 302.0

55
53
49
44
36

7.6

67.4 142.7 219.0 295.3 370.1

44
41
38
33
28

11.4

54.6 117.2 180.1 242.9 304.1

84
81
77
72
64

11.4

67.8 143.8 220.9 297.6 372.7

67
64
60
55
49

15.1

54.6 118.7 182.9 246.7 309.7

113 110 105 100
91

15.1

68.1 146.8 225.6 304.0 380.5

90
87
83
78
71

18.9

54.0 118.6 183.6 248.7 313.3

142 138 133 128 119

18.9

67.4 147.1 227.7 308.1 387.1

113 109 105 100
93

26.5

50.8 116.3 182.2 248.0 313.6

200 195 190 183 174

26.5

64.3 145.3 227.0 308.7 389.4

159 155 150 144 137

34.1

46.8 112.2 178.4 244.7 311.3

257 252 247 239 229

34.1

59.1 140.5 223.2 305.8 387.5

205 201 195 189 181

45.4

38.2 103.4 169.8 236.8 304.1

344 338 331 323 312

45.4

48.5 130.2 213.5 297.1 380.2

274 269 263 256 247

56.8

28.5 93.4 159.1 225.5 292.8

431 424 416 407 395

56.8

35.7 117.4 199.9 282.5 366.5

344 338 331 323 313

Flow (LPM)
TORQUE
SPEED

Flow (LPM)
(nm)
(RPM)

225.5
407

8.0 cu in / rev

10.0 cu inPRESSURE
/ rev
(PSI)

PRESSURE (PSI)
500 1000 1500 2000 2500

T
D
S
E
R
I
E
S

500 1000 1500 2000 2500

.5

445
12

962 1488 2018

10
7
3

464
27

996 1525 2051 2577

24
21
17
10

574 1213 1856 2499 3150

21
18
16
12
8

482 1032 1584 2136 2673

55
53
49
44
36

597 1263 1938 2614 3276

44
41
38
33
28

483 1037 1594 2150 2692

84
81
77
72
64

600 1273 1955 2634 3299

67
64
60
55
49

483 1051 1619 2184 2741

113 110 105 100
91

603 1299 1997 2691 3368

90
87
83
78
71

478 1050 1625 2201 2773

142 138 133 128 119

597 1302 2015 2727 3426

113 109 105 100
93

450 1029 1613 2195 2776

200 195 190 183 174

569 1286 2009 2732 3447

159 155 150 144 137

414
257

993 1579 2166 2755

252 247 239 229

523 1244 1976 2707 3430

205 201 195 189 181

12

338
344

915 1503 2096 2692

338 331 323 312

12

429 1152 1890 2630 3365

274 269 263 256 247

15

252
431

827 1408 1996 2592

424 416 407 395

15

316 1039 1769 2500 3244

344 338 331 323 313

.5

Flow (GPM)

552 1175 1813 2457

9
7
4
3

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

1996
407

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

32

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Performance Data
Code 0195

Code 0230

195 cc / revPRESSURE (BAR)

230 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 120.7 137.9 148.3

34.5 69.0 103.4 137.9 172.4

1.9

80.2 171.6 264.8 359.5

8
7
5
3

1.9

86.0 189.0 295.3 349.6 404.9 438.2

7
6
5
4
3
3

3.8

83.2 176.0 269.7 363.9 457.8

18
16
14
12
8

3.8

89.4 193.4 299.4 353.4 408.4 441.9

15
14
13
12
11
10

7.6

85.6 180.3 276.2 373.1 468.2

37
35
33
30
25

7.6

92.5 199.3 308.0 362.4 417.1 450.2

32
30
29
28
26
25

11.4

85.6 181.2 277.8 374.5 470.0

56
54
51
48
42

11.4

92.5 200.1 309.2 364.5 420.1 453.7

48
47
45
44
42
41

15.1

85.5 182.8 280.4 378.0 474.4

75
73
70
67
60

15.1

92.8 201.9 312.4 367.9 423.7 457.5

65
63
61
60
58
57

18.9

84.4 182.5 281.1 379.6 476.9

95
92
89
85
78

18.9

91.3 201.8 313.7 370.2 426.8 461.0

81
79
77
76
74
73

26.5

79.7 179.2 278.7 377.7 475.6

133 130 127 122 115

26.5

87.0 198.4 311.3 367.7 424.8 459.0

114 112 109 108 106 105

34.1

73.0 172.6 272.8 372.8 471.5

172 169 165 160 151

34.1

79.7 192.0 306.2 363.3 420.7 455.1

147 145 142 140 138 137

45.4

59.9 159.1 260.2 361.2 461.6

230 226 221 215 206

45.4

65.6 178.7 293.2 350.6 408.6 443.6

197 194 191 189 186 185

56.8

44.5 143.8 242.6 342.0 442.4

288 283 278 272 261

56.8

45.2 159.2 275.3 333.2 391.6 426.7

247 243 239 237 235 233

75.7

7.2 118.9 233.5 291.5 350.2 386.1

329 325 321 319 316 314

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

Flow (LPM)

342.0
272

11.9 cu in PRESSURE
/ rev
(PSI)

13.9 cu in / revPRESSURE (PSI)

500 1000 1500 2000 2500

500 1000 1500 1750 2000 2150

.5

761 1673 2614 3094 3584 3879

7
6
5
4
3
3

736 1558 2387 3221 4052

18
16
14
12
8

791 1712 2650 3128 3615 3911

15
14
13
12
11
10

758 1596 2445 3302 4144

37
35
33
30
25

819 1764 2726 3208 3692 3985

32
30
29
28
26
25

758 1604 2459 3315 4160

56
54
51
48
42

819 1771 2737 3226 3718 4016

48
47
45
44
42
41

757 1618 2482 3346 4199

75
73
70
67
60

821 1787 2765 3256 3750 4049

65
63
61
60
58
57

747 1615 2488 3360 4221

95
92
89
85
78

808 1786 2777 3277 3778 4080

81
79
77
76
74
73

705 1586 2467 3343 4210

133 130 127 122 115

770 1756 2755 3255 3760 4063

114 112 109 108 106 105

646 1528 2415 3300 4173

172 169 165 160 151

705 1699 2710 3216 3724 4028

147 145 142 140 138 137

12

530 1408 2303 3197 4086

230 226 221 215 206

12

581 1582 2595 3103 3617 3926

197 194 191 189 186 185

15

394 1273 2147 3027 3916

288 283 278 272 261

15

400 1409 2437 2949 3466 3777

247 243 239 237 235 233

20

64 1052 2067 2580 3100 3417

329 325 321 319 316 314

.5

710 1519 2344 3182

8
7
5
3

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

3027
272

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

Flow (GPM)

PSLGC.PM6, dg, ki

33

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
D
S
E
R
I
E
S

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Performance Data
Code 0260

Code 0295

260 cc / revPRESSURE (BAR)

295 cc / revPRESSURE (BAR)

1.9

34.5 69.0 103.4 113.8 137.9

34.5 69.0 103.4 106.9 127.6

102.6 221.6 344.4 381.9 468.8

7
6
6
6
5

114.6 250.4 390.1 404.0 487.8

6
5
4
4
3

1.9

226.6 350.1 387.9 474.9

3.8 106.0
14
13
13
12
12

256.5 396.4 410.5 493.9

3.8 118.7
12
11
10
10
9

232.6 357.6 395.5 483.7

7.6 109.7
28
27
26
26
24

263.7 406.7 421.1 506.8

7.6 122.9
25
24
22
22
21

233.3 358.9 397.0 485.6

11.4 109.4
43
42
40
39
38

264.1 408.0 422.4 508.5

11.4 122.6
38
36
35
34
33

235.1 361.9 400.1 489.5

15.1 109.6
57
56
54
53
51

265.8 411.1 425.8 512.8

15.1 122.6
50
49
47
47
45

235.5 363.7 402.3 492.9

18.9 108.1
71
70
68
67
65

265.7 412.8 427.5 515.6

18.9 121.1
63
62
60
59
58

231.5 361.3 400.2 491.5

26.5 102.5
100
98
96
95
92

261.1 409.4 424.2 513.5

26.5 115.1
89
87
85
84
82

34.1

94.6 224.3 355.1 394.2 485.7

129 127 124 123 119

252.7 402.3 417.2 507.4

34.1 106.1
115 113 110 110 107

45.4

78.2 208.3 340.7 380.4 473.4

172 169 166 164 160

45.4

87.7 234.3 384.5 399.6 490.8

153 151 148 147 145

56.8

55.2 186.1 319.7 360.2 454.9

215 212 208 206 202

56.8

61.6 209.4 359.7 375.0 466.7

192 189 186 185 182

75.7

14.6 141.8 273.2 313.3 408.0

287 283 279 277 272

75.7

14.2 159.1 304.7 319.3 408.0

256 253 249 249 246

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

313.3
277

15.9 cu inPRESSURE
/ rev
(PSI)

17.9 cu inPRESSURE
/ rev
(PSI)

500 1000 1500 1650 2000

T
D
S
E
R
I
E
S

500 1000 1500 1550 1850

.5

908 1961 3048 3380 4149

7
6
6
6
5

.5

1014 2216 3453 3576 4318

6
5
4
4
3

938 2006 3099 3433 4203

14
13
13
12
12

1051 2270 3509 3633 4372

12
11
10
10
9

971 2059 3165 3501 4281

28
27
26
26
24

1088 2334 3600 3727 4486

25
24
22
22
21

968 2065 3177 3514 4298

43
42
40
39
38

1085 2338 3611 3739 4501

38
36
35
34
33

970 2081 3203 3541 4333

57
56
54
53
51

1085 2353 3639 3769 4539

50
49
47
47
45

957 2084 3219 3561 4363

71
70
68
67
65

1072 2352 3654 3784 4564

63
62
60
59
58

907 2049 3198 3542 4350

100
98
96
95
92

1019 2311 3624 3755 4545

89
87
85
84
82

837 1985 3143 3489 4299

129 127 124 123 119

939 2237 3561 3693 4491

115 113 110 110 107

12

692 1844 3016 3367 4190

172 169 166 164 160

12

776 2074 3403 3537 4344

153 151 148 147 145

15

489 1647 2830 3188 4026

215 212 208 206 202

15

545 1853 3184 3319 4131

192 189 186 185 182

20

129 1255 2418 2773 3611

287 283 279 277 272

20

126 1408 2697 2826 3611

256 253 249 249 246

Flow (GPM)

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

2773
277

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

34

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Performance Data
Code 0330

Code 0365

Code 0390

330 cc /PRESSURE
rev
(BAR)

370 cc PRESSURE
/ rev
(BAR)

390 cc / rev
PRESSURE (BAR)
34.5 69.0 86.2 103.4

34.5 69.0 100.0 117.2

34.5 69.0 91.4 108.6

1.9 133.85 283.25 420.54 496.44

1.9 157.45 332.44 449.04 540.23

1.9

149.8 326.4 416.0 507.8

4
3
2
2

289.0 426.2 501.6

3.8 137.6
11
10
9
9

339.5 456.0 545.9

3.8 163.1
10
9
8
8

3.8

155.9 331.5 420.7 511.7

9
7
7
6

297.4 436.9 514.6

7.6 142.1
22
21
20
19

349.1 466.7 557.1

7.6 168.8
20
19
18
17

7.6

163.0 342.8 433.8 525.6

18
17
15
14

297.5 438.2 516.3

11.4 141.3
34
32
31
30

348.2 466.0 556.7

11.4 167.8
30
29
28
27

11.4

162.9 344.5 436.2 528.6

28
26
25
23

299.3 441.6 520.7

15.1 141.1
45
44
42
41

349.0 467.6 558.6

15.1 166.9
40
39
37
36

15.1

164.3 348.4 441.2 534.4

37
36
34
33

299.2 443.6 523.2

18.9 138.9
57
55
53
51

347.4 466.6 557.7

18.9 164.0
50
49
47
46

30.3

163.5 350.7 444.6 538.7

47
45
44
42

293.7 440.4 521.3

26.5 131.3
80
78
75
73

340.0 459.9 551.3

26.5 154.9
70
69
67
65

26.5

157.4 348.0 443.2 538.3

66
64
62
61

284.5 432.6 514.1

34.1 120.2
103 100
98
95

327.5 414.5 540.5

34.1 142.4
90
89
87
85

34.1

146.5 340.4 437.0 533.3

85
83
81
80

45.4

98.9 263.6 413.2 495.1

137 135 131 129

300.3 422.2 515.2

45.4 113.2
121 119 117 114

45.4

122.9 318.4 416.4 514.1

114 112 110 108

56.8

70.2 235.1 386.4 469.9

171 169 165 162

56.8

79.1 266.1 387.7 481.4

151 149 146 144

56.8

90.0 286.9 385.7 484.5

143 140 138 136

75.7

18.4 178.1 324.8 406.7

229 226 222 218

75.7

17.2 200.7 320.6 412.3

201 199 196 193

75.7

29.8 226.6 325.4 423.6

191 188 186 184

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

Flow (LPM)

324.8
222

19.9 cu in / rev

22.6 cu in / rev

24.0 cu in / rev

PRESSURE (PSI)
500 1000 1325 1575

PRESSURE (PSI)
500 1000 1450 1700

PRESSURE (PSI)
500 1000 1250 1500

.5

1184 2507 3722 4394

5
5
4
4

.5

1393 2942 3974 4781

5
4
4
3

.5

1326 2889 3682 4495

4
3
2
2

1218 2558 3772 4440

11
10
9
9

1444 3005 4036 4832

10
9
8
8

1380 2934 3724 4529

9
7
7
6

1258 2632 3867 4555

22
21
20
19

1494 3090 4131 4931

20
19
18
17

1443 3034 3840 4652

18
17
15
14

1251 2633 3879 4570

34
32
31
30

1485 3082 4125 4927

30
29
28
27

1442 3049 3861 4679

28
26
25
23

1249 2649 3909 4609

45
44
42
41

1477 3089 4139 4944

40
39
37
36

1454 3084 3905 4730

37
36
34
33

1229 2648 3926 4631

57
55
53
51

1452 3075 4130 4936

50
49
47
46

1447 3104 3935 4768

47
45
44
42

1162 2600 3898 4614

80
78
75
73

1371 3009 4071 4880

70
69
67
65

1393 3080 3923 4765

66
64
62
61

1064 2518 3829 4550

103 100
98
95

1260 2899 3669 4784

90
89
87
85

1297 3013 3868 4720

85
83
81
80

12

875 2333 3657 4382

137 135 131 129

12

1002 2658 3737 4560

121 119 117 114

12

1088 2818 3686 4550

114 112 110 108

15

621 2081 3420 4159

171 169 165 162

15

700 2355 3432 4261

151 149 146 144

15

797 2539 3414 4288

143 140 138 136

20

163 1576 2875 3600

229 226 222 218

20

152 1776 2838 3649

201 199 196 193

20

264 2006 2880 3749

191 188 186 184

Flow (GPM)

TORQUE
SPEED

(LB IN)
(RPM)

2875
222

Flow (GPM)

Flow (GPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

35

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
D
S
E
R
I
E
S

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Dimensional Data

Dimensions
Inch equivalents for metric dimensions are shown in (**)

"L"

"L"

95.5
(3.76)
Max.

95.5
(3.76)
Max.

Flange Mount

Wheel Mount
Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.
Rear Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.

Length "L" and Weight

Displacement, Code

0045 0050 0065 0080 0100 0130 0165 0195 0230 0260 0295 0330 0365 0390

SAE "A" Mount

Length "L"

mm
(inches)
kg

Weight

T
D

(lb)

6.09 6.17 6.30 6.44 6.51 6.82 7.08 7.37 7.56 7.86 8.02 8.34 8.71 8.84
(13.4) (13.6) (13.9) (14.2) (14.4) (15.0) (15.6) (16.2) (16.7) (17.3) (17.7) (18.4) (19.2) (19.5)

4 Bolt
mm
Length "L"

(inches)
kg

Weight

S
E
R
I
E
S

136 138
141
144 147
154
160 166 173 179 185 195 200 205
(5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.04)

(lb)

136 138
141
144 147
154
160 166 173 179 185 195 200 205
(5.36) (5.42) (5.54) (5.67) (5.79) (6.04) (6.29) (6.54) (6.79) (7.04) (7.29) (7.54) (7.88) (8.05)
5.66 5.74 5.88 6.01 6.08 6.40 6.65 6.94 7.14 7.43 7.60 7.92 8.30 8.42
(12.5) (12.7) (13.0) (13.3) (13.4) (14.1) (14.7) (15.3) (15.7) (16.4) (16.7) (17.5) (18.3) (18.6)

Magneto Mount
Length "L"

mm
(inches)
kg

Weight

(lb)

136 138
141
144 147
154
160 166 173 179 185 195 200 205
(5.36) (5.42) (5.55) (5.67) (5.80) (6.05) (6.30) (6.55) (6.80) (7.05) (7.30) (7.55) (7.88) (8.05)
6.35 6.44 6.58 6.71 6.80 7.08 7.35 7.62 7.85 8.12 8.30 8.62 8.98 9.12
(14.0) (14.2) (14.5) (14.8) (15.0) (15.6) (16.2) (16.8) (17.3) (17.9) (18.3) (19.0) (19.8) (20.1)

Wheel Mount
Length "L"

mm
(inches)

Weight

kg
(lb)

107 109
112
115 118
124
131 137 143 150 156 162 171 175
(4.21) (4.27) (4.39) (4.52) (4.64) (4.89) (5.14) (5.39) (5.64) (5.89) (6.14) (6.39) (6.73) (6.89)
6.80 6.87 7.01 7.14 7.22 7.53 7.79 8.07 8.27 8.57 8.73 9.05 9.43 9.55
(15.0) (15.2) (15.5) (15.8) (15.9) (16.6) (17.2) (17.8) (18.2) (18.9) (19.2) (20.0) (20.8) (21.1)

PSLGC.PM6, dg, ki

36

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Dimensional Data

Mounting
Inch equivalents for metric dimensions are shown in (**)
14.2 (.56)
2.54 (.100)

82.52 (3.249)

SAE A 2 Bolt

2 x 13.494 (17/32) Thru On

a 106.38 (4.188) BC

14.2 (.56)
2.54 (.100)

45
22 30'

82.52 (3.249)

Magneto

4 x 13.494 (17/32)
Thru on a 106.38 (4.188) BC

45
2.54 (.100)

T
D

44.42 (1.749)

4 Bolt

4 x 3/8-16 UNC thd Thru

On 82.55 (3.250) BC

36.83 (1.450)
19.05 (.750)

Wheel Mount

25.4 (1.00)
49.20 (1.937)

45.72 (1.800)

22.86 (.900)

60.30 (2.374)

PSLGC.PM6, dg, ki

37

Hydraulics

45

4x 13.494 (17/32) Thru Holes

Equally Spaced on a
130.18 (5.125) BC
Parker Hannifin Corporation
Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Dimensional Data

Porting
Inch equivalents for metric dimensions are shown in (**)

48.26 (1.900)

48.26 (1.900)

45.72 (1.800)

SAE O-Ring, NPTF, BSPF

2x
22.86 (.900)

7/8-14 SAE O-Ring

or
1/2-14 NPTF
or
1/2 BSPF

48.26 (1.900)

48.26 (1.900)
63.50 (2.500)
4 x 5/16-18 UNC-2B
x 12.7 (.50) Min
Full thd

Manifold

T
D
S
E
R
I
E
S

2x
31.75 (1.250)

28.58 (1.125)

2 x 14.28 (.562)

2x
22.86 (.900)
45.72 (1.800)

L + 20.3 (.80)

16.26 (.640)
A

Rear, SAE O-Ring

B
3/4-16 UNF O-Ring
24.41 (.961)

31.06 (1.223)

PSLGC.PM6, dg, ki

38

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Dimensional Data

Shaft
Inch equivalents for metric dimensions are shown in (**)
49.02 (1.93)
44.70 (1.760)
19.00 (.748)

M8 x 1.25-6H thd
x .75 Min Deep
27.86 (1.097)
To Top of Key

Key 1/4 x 1 Woodruff

27.97 (1.101)

25.001 (.9843)

25.000 (.9995)
1/4-20 UNC thd
x 15.75 (.62) Min Deep

Key A8 x 7 x 23mm

1" Key
25mm Keyed
49.3 (1.94)
4.32 (.170)
1.24 (.049)
19.00 (.748)
23.52 27.97
(.926) (1.101)

61.2 (2.41)
4.06
(.16)

25.40 (1.000)
25.65 (1.010) x 1/4 Key

25.65 (1.010)
x 6.363 (.2505)
3/4-16 UNF thd
Torque Nut To 300-237 Nm
(225-175 ft lbs)

Long 1" Key

44.7 (1.76)

34.5 (1.36)

125.00 .15 Taper per Meter

(1.500 .006 Taper per Ft)
25.387 (.9995)

25.4 (1.00) Min Full

Spline SAE 6B
4.3 (.17)
1.24 (.049)

1" Tapered

23.52 (.926)

1/4-20 UNC thd

x 15.75 (.62) Min Deep

1" 6B Spline

44.7 (1.76)
30.7 (1.21)

41.4 (1.63)

14.2 (.56) Min Full Spline

25.387 (.9995)
9.72 (.383)
Thru

18.03 (.710)

1" Straight Shaft w/ .38 Cross Hole

7/8" 13 Tooth Spline

Add 1.05" to Shaft

Length for Wheel
Mount Option

PSLGC.PM6, dg, ki

39

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
D
S
E
R
I
E
S

Low Speed High Torque Motors

TD Series

Catalog 1510-20

Ordering Information

TD

XXXX

XX

XXXX

Series

Displacement

Mounting

Porting

Shaft

Rotation

Options

Code Displacement

Code

0045
0050
0065
0080
0100
0130
0165
0195
0230
0260
0295
0330
0365
0390

M***
P*
R
S
T**

2.7
3.0
4.0
5.0
6.0
8.0
10.0
11.9
13.9
15.9
17.9
19.9
22.6
24.0

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Code

T
D

A
F
M
N
U

Porting

Code

Manifold
1/2"-14 NPTF
Rear; 3/4-16 SAE O-Ring
7/8"-14 SAE O-Ring
1/2" BSPF

0
1

Rotation
Standard
Reverse Timed Manifold

*
Available on A & F mounting only
** Available on A & M mounting only
*** Available on A, F & M mounting only

Code
09
10
11
13
21
25
26
28

Mounting
SAE "A" 2 Bolt
4 Bolt
Magneto
Midmount
Wheel

S
E
R
I
E
S

Code
AAAA
AAAB
AAAC
AAAF
AABP
AAAG
AAAH
AAAJ
AAFG
AABJ*
AABK*
AABL*
AABM*
AAFC
AAHD
AAJV
FFAB
FFAA
HAAA**
HAAB**
HAAC**

Shaft
1" Straight w/0.38" Crosshole
1" Keyed
1" 6B Spline
Long 1" Keyed
1" Keyed; Corrosion Resistant
1" Tapered
25mm Keyed w/ 8mm Key
7/8" 13 Tooth Spline

Options
Black Paint
No Paint
Double Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
White Epoxy Paint
White Epoxy Paint, Viton Seals
Bidirectional Shuttle (3:30), Black Paint
Internal Speed Sensor, No Paint
Internal Speed Sensor, Black Paint
External Relief Valve (1894-1), Black Paint
External Relief Valve (1894-1), No Paint
External Relief Valve (1894-1), No Paint, Viton Seals

Not applicable to TD0365 or TD0390 displacements

**

Available only with porting code "M"

PSLGC.PM6, dg, ki

40

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Catalog 1510-20

Quick Reference Data Chart

Low Speed High Torque Motors

Large Frame Torqlink

Quick Reference Data Chart

Series

TF

TG

TH

81-477
(4.9-29.1)

140-958
(8.6-58.5)

140-958
(8.6-58.5)

Max Continuous Pressure

bar
(psi)

206.8
(3000)

206.8
(3000)

206.8
(3000)

Max Intermittent Pressure

bar
(psi)

275.8
(4000)

275.8
(4000)

275.8
(4000)

Max Continuous Torque

nm
(lb in)

680.9
(6027)

1142.1
(9239)

1142.1
(9239)

Max Intermittent Torque

nm
(lb in)

917.5
(8121)

1489.7
(12636)

1489.7
(12636)

Displacement
cc/rev
(cu in/rev)

Max Continuous Flow

LPM
(GPM)

76
(20)

76
(20)

76
(20)

Max Intermittent Flow

LPM
(GPM)

95
(25)

114
(30)

114
(30)

Max Speed
RPM

749

660

660

3008
(6762)

3008
(6762)

3093
(6953)

Max Radial Load

daN
(lb)

PSLGC.PM6, dg, ki

41

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

L
A
R
G
E
F
R
A
M
E
T
O
R
Q
L
I
N
K

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Technical Information

T
F

A Tough Motor for Tough

Applications

S
E
R
I
E
S

Options

Sturdy construction throughout makes Parkers TF

Series motors suitable for the most severe applications. The powertrain uses patented 60:40 spline
geometry for strength. All splines are constantly
flushed with cool fluid for durability. Roller vanes and
sealed commutation assure high volumetric efficiency, smooth low speed operation and extended
life. Shaft seals can withstand full system pressure
and are washed in cool fluid for long life.

Features

1 inch Keyed or Splined, 1 1/4 inch Keyed,

Splined or Tapered, 25mm Shafts

SAE A 2 Bolt, SAE B 2 Bolt or 4 Bolt Magneto

Mounting

Wheel Mount

SAE O-Ring, Manifold or BSPF Porting

Front or Rear Porting

Brake Motor

Clutch Motor

Speed Sensor

Internal Cross - Over Relief Valves

Hot Oil Shuttle

Free Running Rotor Set

Reverse Timed Manifold

Corrosion Resistance

TF Specifications
Code

Roller Vane Power Element For High

Volumetric Efficiency and Long Life

Orbiting Commutator For Accurate Timing,

Smooth Low Speed Operation

Full Flow Spline Lubrication For Extended

Spline Life

High Pressure Shaft Seal For High Back

Pressure Operation Without External Drain Lines

High Flow Shaft Seal Cooling For Long

Seal Life

60:40 Spline Geometry For Superior Powertrain Strength, Long Life

Robust Construction For Quiet operation

0100

81
(4.9)

100
(6.1)

128
(7.8)

141
(8.6)

169
(10.3)

197
(12.0)

238
(14.5)

280
(17.1)

364
(22.2)

405
(24.7)

477
(29.1)

553

562

436

397

332

285

315

267

204

185

156

bar
(psid)

206.9
(3000)

155.2
(2250)

137.9
(2000)

137.9
(2000)

137.9
(2000)

137.9
(2000)

137.9
(2000)

137.9
(2000)

127.6
(1400)

127.6
(1850)

113.4
(1645)

Maximum Intermittent (bar)

psid

275.9
(4000)

241.4
(3500)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

189.7
(2200)

172.4
(2500)

137.9
(2000)

221.4
(1957)

202.0
(1788)

236.6
(2094)

261.4
(2314)

328.9
(2911)

376.1
(3329)

456.0
(4036)

545.4
(4827)

658.8
(5831)

722.3
(6393)

767.1
(6790)

296.9
(2628)

319.2
(2825)

359.7
(3184)

396.6
(3510)

495.4
(4385)

568.7
(5034)

689.3
(6101)

820.9
(7266)

976.3
(8641)

1072.5
(8638)

933.0
(8258)

cc/rev
(cu in/rev)

Maximum Speed (rpm) @

Maximum Continuous Flow
Pressure Differential
Maximum Continuous

Max. Torque @ Max. Continuous

Pressure
nm
(lb-in)
Max. Torque @ Max. Intermittent
Pressure
nm
(lb-in)

0140

Roller Bearings For Heavy Radial Loads

0080

Displacement

0130

0170

0195

0240

0280

0360

0405

0475

PSLGC.PM6, dg, ki

42

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Technical Information

Maximum Side Load Capacity

Performance Data

Flange Mount
Side Load - kg (lbs)
3628.8
(8000)

Continuous / Intermittent* Operation

Continuous

2721.6
(6000)

Intermittent*

1814.4
(4000)

*Intermittent operation is defined as less

than 10% per minute.

907.2
(2000)

Performance data based on testing using 10W40 oil

with a viscosity of 200 SUS at 54 C (130 F.)

-76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6

(-3) (-2) (-1) (0) (1) (2) (3) (4)
Distance from Mounting Face - mm (in)

Wheel Mount
Side Load - kg (lbs)
3628.8
(8000)

2721.6
(6000)

1814.4
(4000)

907.2
(2000)

0
0

25.4 50.8 76.2 101.6 127.0 152.4

(1)
(2)
(3)
(4)
(5)
(6)

Distance from Mounting Face - mm (in)

B-10 Life Factors

Application of the
above uni-directional
radial loads will
result in a B-10 life of
3 million revolutions.
For B-10 life at other
radial loads, apply
the factors from the
curve to the right.

T
F

3
Multiply
Allowable
Radial Load
2
By These
Factors
1
0

0 2 4 6 8 10 12
Life In Millions Of Revolutions
PSLGC.PM6, dg, ki

43

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Performance Data

T
F

Code 0080

Code 0100

80 cc / rev

100 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 155.2 172.4 206.9 241.4

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

S
E
R
I
E
S

1.9

28.9 61.7 94.3 126.3

19
14
8
1

1.9

35.9 76.7 117.6

14
9
4

3.8

30.5 65.0 98.0 130.0 162.0 193.5 226.2 258.6

42
37
31
24
17
13
12
13

3.8

37.8 79.4 120.4 161.6 182.0 202.3 244.3 287.3

33
28
22
17
14
12
9
6

7.6

31.7 67.6 103.6 139.3 173.7 205.7 236.1 265.7

89
83
76
68
60
53
46
40

7.6

39.7 83.9 127.9 171.1 192.1 212.6 253.2 294.0

71
65
58
52
48
45
39
34

11.4

31.9 67.9 104.2 139.9 174.8 208.4 241.6 274.3

135 128 121 113 104
96
86
78

11.4

39.5 84.3 128.6 172.3 194.0 215.5 258.5 301.8

109 102
95
88
84
80
72
64

15.1

32.1 68.9 106.0 142.8 179.2 214.5 248.8 281.4

182 174 166 158 149 139 129
120

15.1

39.9 85.2 130.6 175.6 197.9 220.1 263.7 306.9

147 139 132 124 120 116 107
98

18.9

31.9 69.1 106.7 144.4 181.6 218.3 254.2 289.2

228 219 211 202 193 183 172
163

18.9

39.8 85.8 131.8 177.6 200.4 223.0 267.8 312.1

184 177 169 161 156 152 143
133

26.5

31.0 68.6 106.8 145.2 183.3 221.1 258.5 295.1

321 311 301 291 281 270 258
247

26.5

38.8 85.1 131.7 178.6 202.0 225.3 271.3 317.5

260 252 243 233 229 224 213
202

34.1

29.6 67.4 105.9 144.5 183.3 221.4 259.3 296.9

414 402 391 380 369 357 344
331

34.1

37.2 83.7 130.9 178.4 202.0 225.6 272.4 319.1

336 327 316 306 301 296 284
272

45.4

27.0 64.9 103.5 142.4 181.3 220.1 258.4 296.1

553 540 526 514 501 488 472
456

45.4

33.8 80.8 128.5 176.4 200.3 224.3 271.8 319.2

449 438 426 415 409 403 391
377

56.8

24.3 61.7 100.1 139.1 178.4 217.7 256.4 294.3

693 677 661 646 633 619 601
582

56.8

29.3 76.7 125.0 173.1 197.3 221.3 269.7 317.8

562 549 536 523 517 510 496
480

75.7

21.0 68.6 116.8 165.3 189.7 214.2 263.4 312.2

749 734 718 703 696 689 671
653

Flow (LPM)
TORQUE
SPEED

4.9 cu in / rev

(nm)
(RPM)

178.4
633

Flow (LPM)

6.1 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2250 2500 3000 3500

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

4000

.5

318
14

679 1041
9
4

2289
13

335
33

703 1066 1430 1611 1791 2162

28
22
17
14
12
9

2543
6

917 1233 1537 1821 2090

76
68
60
53
46

2352
40

351
71

743 1132 1514 1700 1882 2241

65
58
52
48
45
39

2602
34

601
128

922 1238 1547 1845 2138

121 113 104
96
86

2428
78

350
109

746 1138 1525 1717 1907 2288

102
95
88
84
80
72

2671
64

284
182

610
174

938 1264 1586 1899 2202

166 158 149 139 129

2491
120

353
147

754 1156 1554 1752 1948 2334

139 132 124 120 116 107

2716
98

282
228

612
219

944 1278 1607 1932 2250

211 202 193 183 172

2560
163

352
184

759 1167 1572 1774 1974 2370

177 169 161 156 152 143

2762
133

274
321

607
311

945 1285 1622 1957 2288

301 291 281 270 258

2612
247

343
260

753 1166 1581 1788 1994 2401

252 243 233 229 224 213

2810
202

262
414

597
402

937 1279 1622 1960 2295

391 380 369 357 344

2628
331

329
336

741 1159 1579 1788 1997 2411

327 316 306 301 296 284

2824
272

12

239
553

574
540

916 1260 1605 1948 2287

526 514 501 488 472

2621
456

12

299
449

715 1137 1561 1773 1985 2406

438 426 415 409 403 391

2825
377

15

215
693

546
677

886 1231 1579 1927 2269

661 646 633 619 601

2605
582

15

259
562

679 1106 1532 1746 1959 2387

549 536 523 517 510 496

2813
480

20

186
749

607 1034 1463 1679 1896 2331

734 718 703 696 689 671

2763
653

.5

256
19

546
14

835 1118
8
1

270
42

575
37

867 1151 1434 1713 2002

31
24
17
13
12

281
89

598
83

282
135

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

1231
646

Flow (GPM)
Performance data is typical. Actual
data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

44

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Performance Data
Code 0130

Code 0140

130 cc / rev

140 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9

1.9

49.8 104.7 159.6

10
7
3

1.9

54.8 115.8 176.2

11
8
4

3.8

51.5 107.1 162.7 218.6 273.6 328.7

24
21
17
13
9
5

3.8

57.3 119.3 180.1 241.4 303.0 364.2

24
20
16
12
8
5

7.6

54.0 112.0 168.9 226.4 283.4 340.0

52
47
42
36
32
29

7.6

59.4 124.4 188.7 252.7 315.9 376.9

50
46
42
37
33
28

11.4

53.7 112.2 170.6 228.6 286.2 343.7

82
76
70
63
57
52

11.4

59.3 124.6 189.4 253.8 317.9 380.7

77
72
68
63
57
52

15.1

54.1 113.7 172.7 231.4 290.1 348.4

112 105
98
91
85
79

15.1

59.7 125.9 191.6 257.3 322.8 386.7

103
98
93
88
82
77

18.9

54.0 114.6 174.9 234.5 293.7 351.9

141 134 127 119 113 106

18.9

59.7 126.5 193.4 260.0 325.9 390.5

130 125 119 113 107 101

26.5

52.8 114.1 175.5 236.6 297.4 357.7

200 192 184 176 169 161

26.5

58.3 126.0 193.9 261.4 328.5 395.1

184 177 170 164 158 151

34.1

50.5 112.5 174.7 236.6 298.3 359.7

259 251 242 233 225 216

34.1

56.0 124.3 192.9 261.1 329.0 396.6

237 230 222 215 208 200

45.4

46.3 108.6 171.5 234.2 296.7 358.9

348 338 328 318 309 299

45.4

51.3 120.1 189.5 258.7 327.8 396.1

317 309 300 292 284 275

56.8

41.2 103.3 166.5 229.5 292.5 355.7

436 426 415 404 394 382

56.8

45.5 114.2 184.0 254.0 323.8 392.8

397 388 378 368 359 349

75.7

29.7 91.7 154.9 218.4 282.2 345.6

583 572 559 547 535 522

75.7

33.7 102.6 172.3 242.8 313.5 384.2

530 520 508 497 485 473

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

345.6
522

7.8 cu in / rev PRESSURE (PSI)

8.6 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500 3000

500 1000 1500 2000 2500 3000

.5

441
10

927 1413
7
3

456
24

948 1440 1935 2422 2909

21
17
13
9
5

507 1056 1594 2137 2682 3224

24
20
16
12
8
5

478
52

991 1495 2004 2508 3009

47
42
36
32
29

526 1101 1670 2237 2796 3336

50
46
42
37
33
28

475
82

993 1510 2023 2533 3042

76
70
63
57
52

525 1103 1676 2246 2814 3370

77
72
68
63
57
52

479 1006 1529 2048 2568 3084

112 105
98
91
85
79

528 1114 1696 2277 2857 3423

103
98
93
88
82
77

478 1014 1548 2076 2600 3115

141 134 127 119 113 106

528 1120 1712 2301 2885 3456

130 125 119 113 107 101

467 1010 1553 2094 2632 3166

200 192 184 176 169 161

516 1115 1716 2314 2908 3497

184 177 170 164 158 151

447
259

996 1546 2094 2640 3184

251 242 233 225 216

496 1100 1707 2311 2912 3510

237 230 222 215 208 200

12

410
348

961 1518 2073 2626 3177

338 328 318 309 299

12

454 1063 1677 2290 2901 3506

317 309 300 292 284 275

15

365
436

914 1474 2031 2589 3148

426 415 404 394 382

15

403 1011 1629 2248 2866 3477

397 388 378 368 359 349

20

263
583

812 1371 1933 2498 3059

572 559 547 535 522

20

298
530

.5

Flow (GPM)

485 1025 1560

11
8
4

908 1525 2149 2775 3401

520 508 497 485 473

Flow (GPM)
TORQUE
SPEED

(LB IN)
(RPM)

1933
547

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

PSLGC.PM6, dg, ki

45

Hydraulics

T
F

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Performance Data

T
F

Code 0170

Code 0195

170 cc / rev

195 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9

S
E
R
I
E
S

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9

1.9

70.8 147.3 223.7

8
6
2

1.9

80.2 168.8 258.3 348.5

8
7
5
3

3.8

74.2 151.5 228.3 306.6 384.6 463.3

19
16
12
9
4
1

3.8

83.3 173.7 263.7 354.0 445.8 538.6

18
16
14
12
9
7

7.6

77.6 159.2 239.9 319.6 397.7 474.2

42
38
34
29
25
21

7.6

85.5 179.3 273.1 366.3 459.5 552.1

37
35
32
29
26
23

11.4

76.9 159.0 240.3 321.0 401.3 481.6

64
60
56
51
45
40

11.4

85.6 179.8 273.9 367.6 461.6 555.2

56
53
51
47
44
40

15.1

76.9 160.3 243.2 325.3 407.2 488.2

86
82
77
72
67
61

15.1

85.8 181.2 276.8 371.9 466.7 560.9

75
72
69
66
62
58

18.9

76.3 160.8 244.6 327.3 409.9 492.0

109 104
99
94
88
82

30.3

85.3 181.9 278.9 375.2 470.3 564.9

94
91
88
84
80
75

26.5

73.9 158.8 244.1 328.9 412.6 495.4

153 148 143 137 130 123

26.5

83.3 180.7 278.7 376.1 472.8 568.7

132 129 125 120 116 110

34.1

70.5 155.9 242.1 327.6 411.8 495.3

198 193 186 180 173 165

34.1

80.1 178.2 276.9 375.0 472.4 568.7

170 166 162 157 152 146

45.4

64.6 150.4 237.4 323.5 408.8 493.0

265 259 252 244 236 228

45.4

73.7 172.1 271.7 370.9 469.3 566.9

228 223 218 212 206 199

56.8

58.1 143.1 230.5 317.2 403.3 488.5

332 325 317 309 300 291

56.8

66.2 163.9 264.1 364.0 463.2 561.6

285 280 273 267 260 252

75.7

43.7 128.6 215.0 301.3 388.1 474.6

444 436 427 417 407 396

75.7

43.0 42.4 41.5 40.6 39.5 38.5

445 1303 2174 3056 3939 4822

Flow (LPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

301.3
417

12.0 cu in / revPRESSURE (PSI)

10.3 cu in / revPRESSURE (PSI)

500 1000 1500 2000 2500 3000

500 1000 1500 2000 2500 3000

.5

.5

627 1304 1980

8
6
2

710 1494 2286 3085

8
7
5
3

657 1341 2021 2714 3404 4101

19
16
12
9
4
1

737 1537 2334 3133 3946 4767

18
16
14
12
9
7

687 1409 2123 2829 3520 4197

42
38
34
29
25
21

757 1587 2417 3242 4067 4887

37
35
32
29
26
23

681 1407 2127 2841 3552 4263

64
60
56
51
45
40

758 1591 2424 3254 4086 4914

56
53
51
47
44
40

681 1419 2153 2879 3604 4321

86
82
77
72
67
61

759 1604 2450 3292 4131 4965

75
72
69
66
62
58

675 1423 2165 2897 3628 4355

109 104
99
94
88
82

755 1610 2469 3321 4163 5000

94
91
88
84
80
75

654 1406 2161 2911 3652 4385

153 148 143 137 130 123

737 1599 2467 3329 4185 5034

132 129 125 120 116 110

624 1380 2143 2900 3645 4384

198 193 186 180 173 165

709 1577 2451 3319 4181 5034

170 166 162 157 152 146

12

572 1331 2101 2863 3618 4364

265 259 252 244 236 228

12

652 1523 2405 3283 4154 5018

228 223 218 212 206 199

15

514 1267 2040 2808 3570 4324

332 325 317 309 300 291

15

586 1451 2338 3222 4100 4971

285 280 273 267 260 252

20

387 1138 1903 2667 3435 4201

444 436 427 417 407 396

20

381 375 367 359 350 341

445 1303 2174 3056 3939 4822

TORQUE
SPEED

(LB IN)
(RPM)

4201
396

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

Flow (GPM)

Flow (GPM)

PSLGC.PM6, dg, ki

46

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Performance Data
Code 0240

Code 0280

240 cc / rev

280 cc / rev

34.5

PRESSURE (BAR)
69.0 103.4 137.9 172.4 206.9

34.5

PRESSURE (BAR)
69.0 103.4 137.9 172.4 206.9

1.9

96.7 202.9 311.6 422.4

7
5
3
1

1.9 118.46 246.35 376.64 509.33 644.42

3.8

99.8 207.7 316.5 427.1 537.3 648.6

15
13
11
8
5
3

252.7 384.0 517.1 651.0 782.4

3.8 122.0
13
12
11
9
7
5

7.6

103.9 216.0 328.8 440.1 551.3 662.5

30
28
26
23
20
17

261.7 397.2 533.9 668.3 801.3

7.6 126.5
26
25
23
22
19
17

11.4

103.8 216.9 330.7 444.1 556.3 668.7

46
44
41
38
35
31

262.1 398.6 535.8 672.1 806.0

11.4 126.2
39
38
36
34
32
29

15.1

104.4 219.3 334.2 448.2 562.4 676.2

62
60
57
54
50
45

264.0 402.1 539.8 676.5 812.0

15.1 126.5
53
51
49
47
44
41

18.9

103.8 220.1 336.1 451.7 566.8 680.7

78
75
72
69
64
60

264.6 403.9 542.5 680.1 815.5

18.9 125.3
66
64
62
60
56
53

26.5

102.1 220.0 338.4 456.0 572.4 688.0

109 106 103
99
94
89

263.4 404.7 545.4 684.4 820.9

26.5 122.7
93
91
88
85
81
77

34.1

98.1 217.1 336.9 455.6 573.0 689.3

141 137 134 130 124 119

259.7 402.4 543.5 683.3 820.7

34.1 117.5
120 117 114 111 106 102

45.4

92.1 210.8 331.0 451.7 570.9 688.0

188 184 180 175 169 162

251.5 394.8 537.6 678.0 815.4

45.4 110.5
160 157 154 149 144 138

56.8

82.0 202.3 323.7 444.5 565.1 684.0

235 231 227 221 214 206

242.5 386.3 529.7 671.7 810.7

56.8 100.3
200 197 193 188 182 175

75.7

60.9 182.6 304.9 427.3 549.4 669.7

315 310 304 297 289 280

94.6

37.8 158.6 278.4 400.2 523.5 646.0

394 389 382 374 365 354

TORQUE
SPEED

(nm)
(RPM)

646.0
354

Flow (LPM)

75.7

76.6 219.7 364.1 508.6 652.7 794.1

267 263 258 252 245 236

94.6

49.9 190.5 331.9 475.2 619.9 763.1

334 330 324 316 308 297

Flow (LPM)

14.5 cu in / revPRESSURE (PSI)

17.1 cu in / revPRESSURE (PSI)

500 1000 1500 2000 2500 3000

500 1000 1500 2000 2500 3000

.5

856 1796 2758 3739

7
5
3
1

.5

1048 2180 3333 4508 5704

6
5
4
3
2

883 1838 2801 3780 4756 5741

15
13
11
8
5
3

1080 2237 3399 4577 5762 6925

13
12
11
9
7
5

920 1912 2910 3895 4880 5864

30
28
26
23
20
17

1120 2316 3516 4726 5915 7092

26
25
23
22
19
17

919 1920 2927 3931 4924 5919

46
44
41
38
35
31

1117 2320 3528 4742 5949 7134

39
38
36
34
32
29

924 1941 2958 3967 4978 5985

62
60
57
54
50
45

1120 2337 3559 4778 5988 7187

53
51
49
47
44
41

919 1948 2975 3998 5017 6025

78
75
72
69
64
60

1109 2342 3575 4802 6020 7218

66
64
62
60
56
53

904 1947 2995 4036 5066 6090

109 106 103
99
94
89

1086 2331 3582 4827 6058 7266

93
91
88
85
81
77

868 1922 2982 4033 5072 6101

141 137 134 130 124 119

1040 2299 3562 4811 6048 7264

120 117 114 111 106 102

12

815 1866 2930 3998 5053 6090

188 184 180 175 169 162

12

978 2226 3494 4758 6001 7217

160 157 154 149 144 138

15

726 1791 2865 3934 5002 6054

235 231 227 221 214 206

15

888 2146 3419 4688 5945 7176

200 197 193 188 182 175

20

539 1616 2699 3782 4863 5928

315 310 304 297 289 280

20

678 1945 3223 4502 5777 7029

267 263 258 252 245 236

25

335 1404 2464 3542 4634 5718

394 389 382 374 365 354

25

442 1686 2938 4206 5487 6754

334 330 324 316 308 297

Flow
(GPM)
PSLGC.PM6, dg, ki

TORQUE
SPEED

(LB IN)
(RPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

47

Hydraulics

5718
354

T
F

Flow (GPM)
Parker Hannifin Corporation
Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Performance Data

T
F

Code 0360

Code 0405

365 cc / rev

405 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 127.6 137.9 172.4 189.7

S
E
R
I
E
S

PRESSURE (BAR)
34.5 69.0 103.4 127.6 137.9 172.4

1.9 162.25 333.94 508.14 630.74 683.23 859.63 948.23

1.9 177.04 362.94 551.73 686.42 744.22 940.62

343.7 518.7 640.8 693.2 866.9 954.1

3.8 168.6
10
9
9
8
8
8
7

3.8 183.49 372.68 561.77 694.96 752.46 945.85

351.8 530.0 653.5 706.0 881.1 968.8

7.6 173.1
20
19
19
18
18
17
16

381.5 576.5 712.5 770.0 961.1

7.6 187.8
18
17
16
14
14
12

351.8 530.9 654.8 707.6 882.8 970.5

11.4 172.5
30
29
29
28
27
26
25

383.2 578.2 714.6 772.7 966.4

11.4 188.1
27
26
24
23
22
20

353.1 533.0 657.7 710.6 886.6 974.3

15.1 172.4
40
40
38
37
37
35
34

385.7 582.4 719.3 777.3 970.6

15.1 188.3
37
35
33
32
31
28

351.8 533.2 658.8 712.2 888.7 976.3

18.9 169.9
51
50
48
47
46
44
43

386.1 584.2 722.3 780.6 974.5

18.9 186.6
46
44
42
40
39
36

349.1 530.7 656.3 709.7 886.9 975.0

26.5 166.0
71
70
68
66
66
63
61

384.0 583.3 722.2 780.9 975.9

26.5 183.4
64
62
60
58
56
53

340.9 524.2 651.4 705.3 883.2 971.1

34.1 157.3
92
90
88
86
85
81
79

377.0 579.0 718.7 777.6 972.2

34.1 175.0
83
81
78
75
73
69

327.9 511.3 638.7 692.9 871.3 959.5

45.4 144.5
122 120 117 115 113 109 106

363.3 565.6 706.4 765.9 962.9

45.4 161.8
111 108 104 101
99
94

309.5 495.4 623.4 677.8 856.2 943.9

56.8 125.0
153 151 147 144 142 139 134

345.6 549.8 690.6 750.6 948.4

56.8 142.2
138 136 131 128 126 120

75.7

94.9 278.5 464.9 593.8 647.9 828.0 917.5

204 202 197 193 191 184 180

94.6

58.3 241.6 424.4 550.9 605.1 788.1 879.5

255 253 248 243 240 232 226

TORQUE
SPEED

(nm)
(RPM)

879.5
226

309.0 513.2 655.3 715.7 915.8

75.7 105.7
185 182 177 172 170 162

94.6

Flow (LPM)

74.2 275.1 473.0 612.1 671.7 871.0

231 229 222 217 214 205

Flow (LPM)

22.2 cu in / rev

24.7 cu in / rev

PRESSURE (PSI)
500 1000 1500 1850 2000 2500 2750

PRESSURE (PSI)
500 1000 1500 1850 2000 2500

.5

1436 2955 4497 5582 6047 7608 8393

5
4
4
4
3
3
3

.5

1567 3212 4883 6075 6587 8325

4
4
3
2
2
2

1492 3042 4591 5672 6136 7673 8445

10
9
9
8
8
8
7

1623 3298 4972 6151 6660 8371

9
8
7
6
6
5

1532 3114 4691 5784 6249 7799 8575

20
19
19
18
18
17
16

1662 3377 5103 6306 6815 8507

18
17
16
14
14
12

1527 3114 4699 5796 6263 7814 8590

30
29
29
28
27
26
25

1665 3392 5118 6325 6839 8554

27
26
24
23
22
20

1526 3125 4718 5821 6290 7847 8624

40
40
38
37
37
35
34

1667 3414 5155 6367 6880 8591

37
35
33
32
31
28

1504 3114 4719 5831 6304 7866 8641

51
50
48
47
46
44
43

1652 3417 5171 6393 6909 8625

46
44
42
40
39
36

1469 3090 4697 5809 6282 7850 8630

71
70
68
66
66
63
61

1623 3399 5163 6392 6912 8638

64
62
60
58
56
53

1392 3017 4640 5766 6243 7817 8595

92
90
88
86
85
81
79

1549 3337 5125 6361 6883 8605

83
81
78
75
73
69

12

1279 2902 4526 5653 6133 7712 8493

122 120 117 115 113 109 106

12

1432 3216 5006 6252 6779 8523

111 108 104 101
99
94

15

1106 2739 4385 5518 5999 7578 8355

153 151 147 144 142 139 134

15

1259 3059 4866 6113 6644 8394

138 136 131 128 126 120

20

840 2465 4115 5256 5735 7329 8121

204 202 197 193 191 184 180

20

936 2735 4542 5800 6335 8106

185 182 177 172 170 162

25

516 2138 3756 4876 5356 6976 7785

255 253 248 243 240 232 226

25

657 2435 4187 5418 5945 7709

231 229 222 217 214 205

Flow
(GPM)
PSLGC.PM6, dg, ki

TORQUE
SPEED

(LB IN)
(RPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

48

Hydraulics

7785
226

Flow (GPM)
Parker Hannifin Corporation
Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Performance Data

T
F

Code 0475

475 cc / rev
PRESSURE (BAR)
34.5 69.0 103.4 113.4 127.6 137.9

S
E
R
I
E
S

1.9 211.34 435.83 663.83 729.93 823.92 892.82

3.8 219.38 448.27 677.07 743.66 837.26 905.66
459.9 691.9 758.9 853.5 922.6
7.6 226.3
15
15
14
14
13
13
460.1 694.3 761.3 856.2 925.5
11.4 225.3
23
23
22
21
20
20
462.2 697.9 765.6 860.9 930.4
15.1 225.2
31
30
29
28
27
27
461.1 698.9 767.1 863.1 933.0
18.9 221.9
39
38
37
36
35
34
457.3 695.8 764.3 860.9 931.2
26.5 216.7
55
54
52
51
50
48
448.0 689.0 758.0 854.7 925.2
34.1 206.6
70
59
67
66
64
63
431.8 672.7 742.8 840.6 911.0
45.4 191.4
94
92
89
89
87
85
408.6 651.4 721.4 819.6 889.7
56.8 165.2
117 116 112 111 109 107
365.0 609.4 680.9 779.6 850.7
75.7 120.9
156 154 151 149 147 145

94.6

TORQUE
SPEED

(nm)
(RPM)

794.0
183

80.3 318.6 556.7 624.9 722.1 794.0

195 194 190 188 185 183

Flow (LPM)

29.1 cu in / rev
PRESSURE (PSI)
500 1000 1500 1645 1850 2000

.5

1870 3857 5875 6460 7292 7902

4
3
3
3
2
2

1941 3967 5992 6582 7410 8016

8
7
7
6
6
6

2003 4071 6124 6717 7554 8166

15
15
14
14
13
13

1994 4072 6145 6738 7578 8192

23
23
22
21
20
20

1993 4091 6177 6776 7620 8235

31
30
29
28
27
27

1964 4081 6186 6790 7639 8258

39
38
37
36
35
34

1918 4048 6159 6765 7620 8242

55
54
52
51
50
48

1829 3965 6098 6709 7565 8189

70
59
67
66
64
63

12

1694 3822 5954 6575 7440 8063

94
92
89
89
87
85

15

1462 3617 5766 6385 7254 7875

117 116 112 111 109 107

20

1070 3231 5394 6027 6900 7530

156 154 151 149 147 145

25

711 2820 4927 5531 6391 7028

195 194 190 188 185 183

Flow
(GPM)
PSLGC.PM6, dg, ki

TORQUE
SPEED

(LB IN)
(RPM)

Performance data is typical. Actual

data may vary slightly from one
production motor to another.

49

Hydraulics

7028
183

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Dimensional Data

T
F

Lengths & Weights

Inch equivalents for metric dimensions are shown in (**)

"L2"
"L1"

S
E
R
I
E
S

Wheel, Front Brake Nose Wheel, Optional Wheel

Mounts

Magneto, SAE "A", SAE "B" Mounts

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.
Rear Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.

Length "L" and Weight

Displacement, Code

0080

0100

191
(7.51)

191
(7.51)

194
196
(7.63) (7.70)

199
202
207
211
221
225
234
(7.82) (7.95) (8.13) (8.32) (8.70) (8.87) (9.20)

13.6
(29.9)

13.6
(30.0)

13.8
13.9
(30.5) (30.7)

14.2
(31.3)

184
(7.25)

184
(7.25)

187
189
(7.37) (7.44)

192
195
200
205
214
218
227
(7.56) (7.69) (7.87) (8.06) (8.44) (8.60) (8.94)

14.2
(31.3)

14.2
(31.4)

14.5
14.6
(31.9) (32.1)

14.8
(32.7)

15.1
(33.3)

15.5
(34.3)

15.8
(34.9)

16.6
(36.6)

17.1
(37.8)

17.8
(39.3)

0080

0100

0170

0195

0240

0280

0360

0405

0475

146
(5.73)

146
(5.73)

149
150
(5.85) (5.92)

153
157
161
166
176
180
188
(6.04) (6.17) (6.35) (6.54) (6.92) (7.08) (7.42)

(lb)

13.9
(30.6)

13.9
(30.7)

14.2
14.3
(31.2) (31.5)

14.5
(32.0)

Optional Wheel Mount

mm
Length "L2"
(inches)

173
(6.80)

173
(6.80)

176
178
(6.93) (6.99)

180
184
189
194
203
207
216
(7.11) (7.24) (7.43) (7.61) (7.99) (8.15) (8.49)

16.9
(37.2)

16.9
(37.3)

17.2
17.3
(37.8) (38.0)

17.5
(38.6)

Magneto &SAE "A"

mm
Length "L1"
(inches)
kg

Weight

(lb)

0130

0140

0170

0195

14.5
(31.9)

0240

14.9
(32.9)

0280

15.2
(33.5)

0360

16.0
(35.2)

0405

16.5
(36.4)

0475

17.2
(37.9)

SAE "B"
mm
Length "L1"

Weight

(inches)
kg
(lb)

Displacement, Code

0130

0140

Wheel & Brake Mount

Length "L2"

mm
(inches)

Weight

Weight

kg

kg
(lb)

14.8
(32.7)

17.8
(39.2)

15.2
(33.6)

18.2
(40.2)

15.5
(34.2)

18.5
(40.8)

16.3
(35.9)

19.3
(42.5)

16.9
(37.2)

19.8
(43.7)

17.5
(38.6)

20.5
(45.2)

PSLGC.PM6, dg, ki

50

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Dimensional Data

T
F

Mounting
Inch equivalents for metric dimensions are shown in (**)
15.7 (.62)
62.81
(2.473)

2.79 (.110)

SAE "A" 2 Bolt Flange

S
E
R
I
E
S

82.55
(3.250)

2X 13.5 (17/32) on a
106.38 (4.188) BC

65.3 (2.57)

9.4 (.37)

15.7 (.62)

2 x 14.29 (9/16) thru holes

on a 146.05 (5.750) BC

SAE "B" 2 Bolt Flange

174.5 (6.87)

101.57 (3.999)

62.81 (2.473)
15.7 (.62)

4 Bolt Magneto

22 30'

2.8 (.11)

82.52 (3.249)
133.4 (5.25)

4 x 13.49 (17/32) thru holes

on a 106.38 (4.188) BC
45

PSLGC.PM6, dg, ki

51

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Dimensional Data

T
F
S
E
R
I
E
S

Mounting, Wheel
Inch equivalents for metric dimensions are shown in (**)

46.7 (1.84)
63.83 (2.513)
36.8
(1.45)

4.1 (.16) Min

19.0 (.75)

39.9 (1.57)

45

40.1 (1.58) Max

Wheel
62.99 82.52
(2.480) (3.249)

25.4 (1.00)
25.4 (1.00)

4X 13.5 (17/32) equally spaced

on a 147.62 (5.182) Bolt Circle

.16 (4.1)
Min

36.8 (1.45)
46.7 (1.84)

45

126.95 ( 4.998)
88.85 (3.498)

Wheel, Front Brake Nose

4 x 13.49 (17/32) thru

holes on a 147.62 ( 5.812)
Bolt Circle

19.1 (.75)

44.2 (1.74)

4 x 5/16-18 UNC thd equally

spaced on a 76.20 ( 3.000)
Bolt Circle

45

4.8 (.19) Min

36.1 (1.42) Max

107.90 (4.248)

126.95 ( 4.998)

Wheel, Optional

95.3 (3.75)
Ref

4 x 13.49 (17/32) thru

holes on a 147.62 ( 5.812)
Bolt Circle

PSLGC.PM6, dg, ki

52

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Dimensional Data

T
F

Porting
SAE O-Ring & BSPF

Manifold
64.3
(2.53)

64.3
(2.53)

31.75 (1.250)

S
E
R
I
E
S

22.86 (.900)

63.50 (2.500)
25.40 (1.000)

45.72 (1.800)

4 x 5/16-18 UNC thd

x .500 min deep

14.27 (.562)
28.58 (1.125)

7/8-14 SAE O-Ring

or
1/2" BSPF

62.99 (2.480)

Rear Ports
65.53 (2.580)
7/8-14 SAE O-Ring

22.86 (.900)

A
129.5
(5.10)

7/8-14 SAE O-Ring

B
45.72 (1.800)

14.27 (.562)
65.53 (2.580)
28.58 (1.125)
22.86 (.900)

A
63.50 (2.500)

Manifold

45.72 (1.800)
31.75 (1.250)
4 x 5/16-18 UNC thd
x .50 Min Deep

Consult Factory for

ISO 6149 Porting

PSLGC.PM6, dg, ki

53

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Dimensional Data

T
F
S
E
R
I
E
S

Shafts
Inch equivalents for metric dimensions are shown in (**)

48.8 (1.92)

25.65 ( 1.010)
x 6.38 (.251) Wide

57.4 (2.26)*
47.2
(1.86)

38.33 (1.509)
4.3 (.17)

25.40 (1.00) Min. Full Spline

27.99 (1.102)
25.40 (1.000)

31.75 (1.250)
27.31 (1.075)

1.24 (.049)

23.52 (.926)
5/8-18 UNF thd
x 19.1 (.75) Min Deep

19.00 (.748)
Keyway Center Line

37.34 (1.470)

1" Keyed

1 1/4" 14 Tooth Spline

49.5 (1.95)

48.8 (1.92)
4.3 (.17)

23.50 (.925)
x 7 (.2749)

2.8 (.11)
37.34 (1.47)

9.09 (.358)

1.24 (.049)

28.00 (1.102)
23.52 (.926)
M6 x 1-6H thd
19.1 (.75) Min Deep

25.40 (1.00) Min. Full Spline

25 mm Keyed

1" 6B Spline

61.7 (2.43)

60.2 (2.37)
2.8 (.11)
50.3 (1.98)

36.50 (1.437)
x 7.90 (.311)

35.1 (1.38)

4.22 (.166)

7.90 (.311)
Woodruff Key

34.90 (1.374)

1.000-20 UNEF thd

38.10 Taper per Meter
(1.500 Taper per Foot)

5/8-18 UNF thd

x 19.1 (.75) Min Deep

1 1/4" Keyed

25.000 (.9837)

* Add .26" for SAE B Mount

Add 1.78" for Wheel Mount
Add 1.68" for Optional Wheel Mount

1 1/4" Taper

PSLGC.PM6, dg, ki

54

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Speed Sensor

T
F

An Economical Sensor for Speed

Readout
This rugged, weather resistant speed sensor is a
Hall effect device. When externally powered, 30
square wave digital pulses per output shaft revolution are produced. By signal multiplication, 60
pulses per revolution can be obtained.

S
E
R
I
E
S

The installation of this economical sensor does not

affect the torque or side load capability of the
TorqlinkTM motor into which it is installed.

Features
Operating Voltage Range .......... 4.5 to 24 VDC
Operating Temperature ............. -40 C to 93 C
(-40 F to 200 F)

2
N/C

1
+

3
-

4
Output

Operating Frequency Range ..... 0 to 100 KHZ

Maximum Sink Current ............. 20 mA
Connection ................................ DC Din Standard
4 Pin Micro-Mini
Pin Diameter ............................. 12mm
Sensor Output ........................... 30 Pulses per
Revolution which can be doubled electronically.
Pull-up Resistor Value Formula
(for 1/4 Watt, 5% Tolerance)
V Supply (4.5-24 VDC)

= Resistor Value
Desired Sink Current (0-20 mA 20%)
(K - Ohms)

+ 4.5 to 24 VDC

Pin # 4

Output

Pin # 3

- Negative

Pin # 2

No Connection

SENSOR

On State Current: 5 mA
Higher wattage resistor will be needed for higher
sink current.

+V Off State

Pin # 1

Min Off State = .95%+V

On State Max On State = .400VDC

0V

Cable not included

PSLGC.PM6, dg, ki

55

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series

Catalog 1510-20

Ordering Information

T
F

TF

XXXX

Series

Displacement

Mounting

Porting

S
E
R
I
E
S

Code Displacement
0080
0100
0130
0140
0170
0195
0240
0280
0360
0405
0475

04.9
06.1
07.8
08.6
10.3
12.0
14.5
17.1
22.2
24.7
29.1

Code
A
B
M
U
L
W*
*

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Code
A
B
E
J
M*
S
T**

Available on A & M mounting only

Shaft
1"6B Spline
1" Keyed
1 1/4" Keyed
10B Spline
1 1/4" 14 Tooth Spline
19 Tooth Spline
15 Tooth Spline
1 1/4" Tapered
25mm Keyed
13 Tooth Spline

XXXX

Rotation

Options

Code

Not available on L, U or W mounting

Requires rear porting

01
02
03
04
05
06
07
08
22
28

Porting

**

SAE "A" 2-Bolt

SAE "B" 2-Bolt
Magneto
Wheel; Standard
Wheel; Front Brake Nose
Wheel, Optional

Shaft

7/8"-14 SAE O-Ring; Rear Axial

7/8"-14 SAE O-Ring; Rear Radial
Manifold; Rear Radial
ISO 6149 M22x1.5
Manifold
7/8"-14 SAE O-Ring
1/2" BSPF

Mounting

Code

XX

Code
AAAA
AAAB
AAAC
AAFC
AAAF***
AABP***
AAAG
AAAH
AAHD
AAAJ
AAFG
AAAT*
AAFX*
AAAU*
AAGF*
AABJ
AABK
AABL
AABM
BBBA*
BBBM*
BBBG*
BBBJ*
BBBB*
BBBN*
BBBK*
BBBC*
BBBF*
BBBD*
BBBW*
FFAA
FFAB
FFAH
FFAJ
*

0
1

Rotation
Standard
Reverse Timed Manifold

Options
Black Paint
No Paint
Double Paint
White Epoxy Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Viton Seals, White Epoxy Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Bidirectional Shuttle (11:00**), Black Paint
Bidirectional Shuttle (11:00**), No Paint
Bidirectional Shuttle (11:00**), Castle Nut, Black Paint
Bidirectional Shuttle (11:00**), Castle Nut, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
1000 PSI Internal Bidirectional Relief, Black Paint
1000 PSI Internal Bidirectional Relief, No Paint
1500 PSI Internal Bidirectional Relief, Black Paint
1500 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Black Paint
2000 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Castle Nut, Black Paint
3000 PSI Internal Bidirectional Relief, Black Paint
3000 PSI Internal Bidirectional Relief, No Paint
4000 PSI Internal Bidirectional Relief, Black Paint
4000 PSI Internal Bidirectional Relief, No Paint
Internal Speed Sensor, Black Paint
Internal Speed Sensor, No Paint
Internal Speed Sensor, Castle Nut, No Paint
Internal Speed Sensor, Castle Nut, Black Paint

Not available with A, B or E porting

**

Shuttle port position as viewed from shaft end of motor

***

Available only with shaft code 08

PSLGC.PM6, dg, ki

56

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series Brake Motor

Catalog 1510-20

Technical Information

T
F

Brake Motor
This motor/brake combination consists of a TF
Series motor built into a front mounted brake. The
brake is a wet disc, spring set, hydraulically released
unit. When hydraulic pressure is absent at the pilot
port of the brake, internal springs will hold against
6900 lb in of torque. The brake will start to release
when 190 PSI is present in the brake pilot port and
will be fully disengaged when that pressure reaches
260 PSI. The pilot port is capable of withstanding
the maximum operating pressure of the TF Series
motor.

S
E
R
I
E
S

Dimensions
Inch equivalents for metric dimensions are shown in (**)

218.4 (8.60)

"L"

7/16-20 Straight THD

O-Ring Ports 2 PL
1 Pressure Port
1 Bleed Port

6.4 (.25)

PSLGC.PM6, dg, ki

57

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series Brake Motor

Catalog 1510-20

Ordering Information

T
F

TF

XXXX

Series

Displacement

Mounting

Porting

S
E
R
I
E
S

Code Displacement
0080
0100
0130
0140
0170
0195
0240
0280
0360
0405
0475

04.9
06.1
07.8
08.6
10.3
12.0
14.5
17.1
22.2
24.7
29.1

Code
8

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Code
A
B
S

Mounting
Wheel Brake

Code
03
05
08
31
32
36

Shaft
1
1
1
1
1
1

1/4"
1/4"
1/4"
1/2"
1/2"
1/2"

Keyed
14 Tooth Spline
Tapered
Tapered
Keyed
17 Tooth Spline

XX
Shaft

Porting

XXXX

Rotation

Options

Code

7/8"-14 SAE O-Ring; Rear Axial

7/8"-14 SAE O-Ring; Rear Radial
7/8"-14 SAE O-Ring; Front Radial

Code
AAAA
AAAB
AAAC
AAFC
AAAF***
AABP***
AAAG
AAAH
AAHD
AAAJ
AAFG
AAAT*
AAFX*
AAAU*
AAGF*
AABJ
AABK
AABL
AABM
BBBA*
BBBM
BBBG*
BBBJ*
BBBB*
BBCC
BBBK*
BBBC*
BBBF*
BBBD*
BBBW*
*

0
1

Rotation
Standard
Reverse Timed Manifold

Options
Black Paint
No Paint
Double Paint
White Epoxy Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Viton Seals, White Epoxy Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Bidirectional Shuttle (11:00**), Black Paint
Bidirectional Shuttle (11:00**), No Paint
Bidirectional Shuttle (11:00**), Castle Nut, Black Paint
Bidirectional Shuttle (11:00**), Castle Nut, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
1000 PSI Internal Bidirectional Relief, Black Paint
1000 PSI Internal Bidirectional Relief, No Paint
1500 PSI Internal Bidirectional Relief, Black Paint
1500 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Black Paint
2000 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Castle Nut, Black Paint
3000 PSI Internal Bidirectional Relief, Black Paint
3000 PSI Internal Bidirectional Relief, No Paint
4000 PSI Internal Bidirectional Relief, Black Paint
4000 PSI Internal Bidirectional Relief, No Paint

Not available with A or B porting

**

Shuttle port position as viewed from shaft end of motor

***

Available only with shaft code 08 or 31

PSLGC.PM6, dg, ki

58

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series Brake Motor

Catalog 1510-20

Technical Information

T
F

Dimensions
Inch equivalents for metric dimensions are shown in (**)

S
E
R
I
E
S

4.8 (.19)

2 x 7/8-14 SAE
O-Ring
21.6 (.85)
This dimension
applies to both ports.

Rear View
Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.
Rear Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.

4 x 13.5 (.531) On
171.42 (6.749) BC Spotface
20.3 (.80)

45

196.8 (7.75)

Front View

PSLGC.PM6, dg, ki

59

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series Clutch Motor

Catalog 1510-20

Technical Information

T
F
S
E
R
I
E
S

Clutch Motor
The Clutch Motor consists of a TF Series motor
separated from the output shaft by a face spline
coupling. The coupling is held apart by springs,
disconnecting the motor from the output shaft,
allowing the output shaft to freewheel. When
hydraulic pressure is applied to either motor port,
the springs separating the coupling are overcome
and the motor is coupled to the output shaft.
Notes:
1) Consult factory if clutch is to be engaged
while output shaft is rotating.
2) Clutch may not disengage if there is residual torque on output shaft when pressure
is lost at motor ports.
3) Minimum pressure to engage clutch - 125
PSI.
4) To assure clutch disengagement, pressure
at motor ports must be below 70 PSI.
5) Shaft will freewheel when pressure is lost at
motor ports whether by design or inadvertently. The possibility of unplanned freewheeling should be considered in the
design of the system.

Dimensions
Inch equivalents for metric dimensions are shown in (**)

"L1" +(3.1)

143.0 (5.63)

63.5 (2.50)

2.79 (.11)
44.4 (1.75) Min
Full Spline

A
129.5
(5.10)
Max.

82.52 (3.249)

2 x 7/8-14 SAE
O-Ring Ports

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.
Rear Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.
PSLGC.PM6, dg, ki

60

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TF Series Clutch Motor

Catalog 1510-20

Technical Information

T
F

Dimensions
Inch equivalents for metric dimensions are shown in (**)
62.81 (2.473)
22 30'

S
E
R
I
E
S

25.4 (1.00)
2 PL

5/8-18 UNF
thd x 1.00 Deep

4 x 13.49 (.531) Thru Holes

on a 106.38 (4.188) BC

45

Clutch Motor Ordering Information

TF

XXXX

XX

XXXX

Series

Displacement

Mounting

Porting

Shaft

Rotation

Options

Code Displacement
0080
0100
0130
0140
0170
0195
0240
0280
0365

Code
G

04.9
06.1
07.8
08.6
10.3
12.0
14.5
17.1
22.2

cu
cu
cu
cu
cu
cu
cu
cu
cu

Code

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Porting
7/8"-14 SAE O-Ring

Code
AAAA
AAAB
AAAC
AAFC
AAAG
AAAH
AAHD
AAAJ
AAFG
AAAT
AAFX
AABJ
AABK
AABL
AABM
BBBA
BBBM
BBBG
BBBJ
BBBB
BBCC
BBBC
BBBF
BBBD
BBBW

Mounting
Magneto, Clutch

Code

Code

Shaft

03

1 1/4" Keyed

05

1 1/4" 14-Tooth Spline

**

0
1

Rotation
Standard
Reverse Timed Manifold

Options
Black Paint
No Paint
Double Paint
White Epoxy Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Viton Seals, White Epoxy Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Bidirectional Shuttle (11:00**), Black Paint
Bidirectional Shuttle (11:00**), No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
1000 PSI Internal Bidirectional Relief, Black Paint
1000 PSI Internal Bidirectional Relief, No Paint
1500 PSI Internal Bidirectional Relief, Black Paint
1500 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Black Paint
2000 PSI Internal Bidirectional Relief, No Paint
3000 PSI Internal Bidirectional Relief, Black Paint
3000 PSI Internal Bidirectional Relief, No Paint
4000 PSI Internal Bidirectional Relief, Black Paint
4000 PSI Internal Bidirectional Relief, No Paint

Shuttle port position as viewed from shaft end of motor

PSLGC.PM6, dg, ki

61

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Technical Information

Exceptional Strength and

Durability in a High Performance
Motor
The heart of Parkers TG Series powertrain, the
torque link, is an extra heavy duty part that includes
patented 60:40 spline geometry. Rugged construction throughout allows the transmission of over
13,000 lb in of torque. The entire powertrain is
continually washed in cool, high flow fluid to assure
long life. Roller vanes and sealed commutator
maintain high efficiency and provide smooth low
speed performance.

T
G

Options

S
E
R
I
E
S

Features

1 inch Keyed or Splined, 1 1/4 inch Keyed

Splined or Tapered, 1 3/8 inch Keyed or Tapered
Shafts
SAE A 2 Bolt, SAE B 2 Bolt or 4 Bolt Magneto
Mounting
Wheel Mount
SAE O-Ring, Manifold or BSPF Porting
Front or Rear Porting
Brake Motor
Speed Sensor
Internal Cross - Over Relief Valves
Hot Oil Shuttle
Free Running Rotor Set
Reverse Timed Manifold
Corrosion Resistance

Roller Bearings For Heavy Radial Loads

Roller Vane Power Element For High

Volumetric Efficiency and Long Life

Orbiting Commutator For Accurate Timing,

Smooth Low Speed Operation

Full Flow Spline Lubrication For Extended

Spline Life

High Pressure Shaft Seal For High Back

Pressure Operation Without External Drain
Lines

High Flow Shaft Seal Cooling For Long

Seal Life

60:40 Spline Geometry For Superior Powertrain Strength, Long Life

Robust Construction For Quiet operation

TG Specifications
Code
Displacement

0140

0170

0195

0240

0280

0335

140
(8.6)

169
(10.3)

195
(11.9)

237
(14.5)

280
(17.1)

337
(20.6)

405
(24.7)

476
(29.1)

528

442

381

314

266

221

185

bar
(psid)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

bar
(psid)

275.9
(4000)

275.9
(4000)

275.9
(4000)

275.9
(4000)

275.9
(4000)

406.8
(3601)

494.9
(4380)

576.0
(5098)

704.9
(6239)

824.9
(7301)

541.6
(4794)

659.6
(5838)

765.6
(6776)

937.5 1096.7 1337.0 1386.4 1424.5 1317.2 1348.4 1489.6 1385.4

(8298) (9707) (11834) (12271) (12608) (11659) (11935) (13185) (12262)

cc/rev
(cu in/rev)

Maximum Speed (rpm) @

Maximum Continuous Flow
Pressure Differential
Maximum Continuous
Maximum Intermittent

Max. Torque @ Max. Continuous

Pressure
nm
(lb-in)
Max. Torque @ Max. Intermittent
Pressure
nm
(lb-in)

0405

0475

0530

0625

0785

0960

529
(32.3)

624
(38.0)

786
(48.0)

958
(58.5)

157

141

120

95

78

172.4
(2500)

137.9
(2000)

137.9
(2000)

120.7
(1750)

103.4
(1500)

69.0
(1000)

275.9
(4000)

241.4
(3500)

206.9
(3000)

172.4
(2500)

155.2
(2250)

137.9
(2000)

103.4
(1500)

1006.4
(8908)

991.1
(8772)

954.1 1057.7 1054.9 1142.0

(8445) (9362) (9337) (10108)

923.4
(8173)

PSLGC.PM6, dg, ki

62

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Technical Information

Maximum Side Load Capacity

Performance Data

Flange Mount
Side Load - kg (lbs)
3628.8
(8000)

Continuous / Intermittent* Operation

2721.6
(6000)

Continuous

1814.4
(4000)

Intermittent*

*Intermittent operation is defined as less

than 10% per minute.

907.2
(2000)

Performance data based on testing using 10W40 oil

with a viscosity of 200 SUS at 54 C (130 F.)

-76.2 -50.8 -25.4 0 25.4 50.8 76.2 101.6

(-3) (-2) (-1) (0) (1) (2) (3) (4)
Distance from Mounting Face - mm (in)

Performance data is typical. Actual data may vary

slightly from one production motor to another.

S
E
R
I
E
S

Wheel Mount
Side Load - kg (lbs)
3628.8
(8000)

2721.6
(6000)

1814.4
(4000)

907.2
(2000)

0
0

25.4 50.8 76.2 101.6 127.0 152.4

(1)
(2)
(3)
(4)
(5)
(6)

Distance from Mounting Face - mm (in)

B-10 Life Factors

Application of the
above uni-directional
radial loads will
result in a B-10 life of
3 million revolutions.
For B-10 life at other
radial loads, apply
the factors from the
curve to the right.

Multiply
3
Allowable
Radial Load
By These
2
Factors
1
0

0 2 4 6 8 10 12
Life In Millions Of Revolutions
PSLGC.PM6, dg, ki

63

Hydraulics

T
G

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0140

Code 0170

140 cc / rev

170 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

T
G
S
E
R
I
E
S

PRESSURE (BAR)

34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

1.9

58.6 119.8
9
4

1.9

70.0 145.1 219.7 295.2 372.0 450.0

9
7
5
4
3
2

3.8

61.0 123.1 184.7 246.3

22
17
11
6

3.8

73.7 151.1 226.6 303.1 381.3 459.0 536.0 610.3

20
18
16
14
12
11
8
8

7.6

64.3 130.6 195.5 258.3 319.4 380.5 440.5 502.4

49
43
36
30
23
19
12
12

7.6

76.6 157.0 237.8 318.8 399.4 477.5 554.6 631.2

42
40
37
35
32
30
27
25

11.4

63.8 130.9 197.0 262.2 327.5 392.8 457.3 520.6

75
69
62
55
47
40
33
29

11.4

76.6 157.8 239.2 320.4 401.5 481.6 560.7 638.6

64
61
58
56
53
50
46
44

15.1

63.7 132.2 199.7 266.4 332.5 397.4 461.2 524.7

102
94
87
80
72
64
57
52

15.1

76.7 159.2 242.0 324.5 406.3 486.9 567.3 645.8

86
83
80
77
74
71
67
64

18.9

62.8 132.2 200.7 268.3 335.3 401.8 467.2 531.1

128 120 112 105
97
89
81
76

18.9

76.3 159.6 242.9 325.9 408.5 490.2 571.3 650.9

108 104 101
98
94
91
87
83

26.5

61.0 131.1 201.0 270.0 338.3 405.8 472.4 538.1

182 172 164 155 146 138 130
123

26.5

74.7 158.7 243.1 327.6 411.5 494.2 576.3 657.3

153 148 143 140 136 132 127
123

34.1

58.2 129.1 199.7 269.5 338.5 406.8 474.4 541.6

235 225 215 206 196 187 179
171

34.1

71.4 156.5 241.8 326.6 411.0 494.9 577.8 659.6

197 191 186 181 177 173 168
163

45.4

53.2 123.8 195.3 266.2 336.0 405.3 473.7 541.6

315 303 292 281 271 261 252
243

45.4

65.9 150.7 236.8 323.1 408.6 492.8 576.3 657.9

263 256 250 244 239 234 228
223

56.8

47.2 117.7 189.0 260.6 331.4 401.0 470.3 539.0

395 381 368 357 346 336 325
314

56.8

59.2 144.0 229.9 316.8 403.6 488.9 572.8 655.4

330 322 314 308 302 296 289
283

75.7

33.8 105.2 176.8 248.3 319.2 390.3 460.7 530.1

528 512 497 484 472 459 447
435

75.7

43.2 129.1 215.6 303.1 390.3 476.3 561.7 645.6

442 432 422 413 406 399 391
383

94.6

19.5 89.7 161.1 232.6 304.5 376.4 447.5 517.3

660 643 626 612 598 583 569
555

94.6

27.0 111.1 197.4 285.0 372.7 459.9 546.7 631.7

554 543 531 520 511 501 492
483

Flow (LPM)

TORQUE
SPEED

8.6 cu in / rev

Flow (LPM)

304.5
598

10.3 cu in / rev

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

.5

(nm)
(RPM)

519 1060
9
4

540 1090 1635 2180

22
17
11
6

569 1156 1730 2286 2827 3368 3899

49
43
36
30
23
19
12

4000
TORQUE
SPEED

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

(LB IN)
(RPM)

3899
12

.5

4000

620 1284 1945 2613 3293 3983

9
7
5
4
3
2

652 1337 2006 2683 3375 4063 4744

20
18
16
14
12
11
8

5402
8

4447
12

678 1390 2105 2822 3535 4226 4909

42
40
37
35
32
30
27

5587
25

565 1159 1744 2321 2899 3477 4048

75
69
62
55
47
40
33

4608
29

678 1397 2117 2836 3554 4263 4963

64
61
58
56
53
50
46

5652
44

564 1170 1768 2358 2943 3517 4082

102
94
87
80
72
64
57

4644
52

679 1409 2142 2872 3596 4310 5021

86
83
80
77
74
71
67

5716
64

556 1170 1776 2375 2968 3556 4135

128 120 112 105
97
89
81

4701
76

675 1413 2150 2885 3616 4339 5057

108 104 101
98
94
91
87

5761
83

540 1160 1779 2390 2994 3592 4181

182 172 164 155 146 138 130

4763
123

661 1405 2152 2900 3642 4374 5101

153 148 143 140 136 132 127

5818
123

515 1143 1768 2385 2996 3601 4199

235 225 215 206 196 187 179

4794
171

632 1385 2140 2891 3638 4380 5114

197 191 186 181 177 173 168

5838
163

12

471 1096 1729 2356 2974 3587 4193

315 303 292 281 271 261 252

4794
243

12

583 1334 2096 2860 3617 4362 5101

263 256 250 244 239 234 228

5823
223

15

418 1042 1673 2307 2933 3549 4163

395 381 368 357 346 336 325

4771
314

15

524 1275 2035 2804 3572 4327 5070

330 322 314 308 302 296 289

5801
283

20

299
528

931 1565 2198 2825 3455 4078

512 497 484 472 459 447

4692
435

20

382 1143 1908 2683 3455 4216 4972

442 432 422 413 406 399 391

5714
383

25

173
660

794 1426 2059 2695 3332 3961

643 626 612 598 583 569

4579
555

25

239
554

5591
483

Flow (GPM)

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.

983 1747 2523 3299 4071 4839

543 531 520 511 501 492

Flow (GPM)

PSLGC.PM6, dg, ki

64

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0195

Code 0240

195 cc / rev

240 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

1.9

82.8 169.8
7
3

1.9

105.3 215.5 327.0

6
4
2

3.8

86.0 174.7 262.8 350.7

16
13
8
3

3.8

108.5 220.8 333.3 445.5 558.0 670.0

14
12
9
6
3
2

7.6

90.3 185.1 278.5 369.4 457.1 543.8 631.4 720.2

35
32
27
21
16
11
7
6

7.6

111.6 229.5 346.3 462.1 577.0 689.2 798.5 908.0

30
27
24
20
17
14
11
9

11.4

89.7 185.2 279.7 373.2 466.8 561.5 654.4 745.1

55
50
45
39
34
28
23
19

11.4

111.1 229.2 347.0 463.3 579.4 696.1 811.4 924.6

45
42
39
35
31
27
23
20

15.1

89.7 186.9 283.5 379.2 474.1 567.5 658.7 749.6

74
69
64
58
52
46
40
35

15.1

110.5 230.1 349.1 467.3 584.8 701.3 816.8 930.3

61
58
54
49
45
42
37
33

18.9

88.5 186.8 284.4 381.3 477.2 572.2 666.0 758.1

93
88
83
76
70
64
58
52

18.9

108.7 229.3 349.3 468.2 586.4 704.0 820.1 934.5

77
73
69
64
60
56
51
47

26.5

86.1 184.9 284.0 382.3 479.6 576.0 671.1 765.1

131 126 120 113 106
99
92
86

26.5

105.4 226.5 347.8 467.9 586.8 704.9 821.9 937.5

108 104
99
94
89
84
78
73

34.1

82.6 182.6 282.3 381.1 478.9 575.4 670.6 765.3

170 164 157 150 142 135 127
120

34.1

100.6 222.8 344.4 464.6 584.0 701.9 818.5 934.5

140 135 129 123 117 112 106
100

45.4

76.5 176.5 277.4 377.7 476.4 574.1 670.4 765.6

228 221 213 205 196 188 179
172

45.4

94.0 216.0 338.5 459.9 579.0 696.3 812.9 929.1

187 181 175 167 161 154 147
140

56.8

69.3 169.2 269.9 370.9 471.0 569.4 667.4 764.3

285 278 269 260 251 242 232
233

56.8

85.1 207.0 330.0 452.9 574.1 693.4 811.4 927.8

235 228 220 212 204 196 188
180

75.7

50.6 152.5 253.6 354.9 455.4 555.7 655.1 752.8

381 373 363 353 342 331 321
310

75.7

63.2 186.9 310.0 433.2 555.5 676.9 795.9 913.0

314 306 297 287 278 268 258
248

94.6

37.7 130.8 230.9 332.3 433.5 534.3 634.0 734.4

477 468 457 445 433 421 409
397

94.6

59.2 161.2 283.2 406.2 529.9 653.0 774.3 894.0

393 384 373 363 352 340 328
317

Flow (LPM)

11.9 cu in / rev

TORQUE
SPEED

733 1503
7
3

534.3
421

Flow (LPM)

14.5 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500 3000 3500 4000

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

.5

(nm)
(RPM)

4000

TORQUE
SPEED

(LB IN)
(RPM)

4813
11

.5

932 1907 2894

6
4
2

960 1954 2950 3943 4939 5930

14
12
9
6
3
2

6375
6

988 2031 3065 4090 5107 6100 7068

30
27
24
20
17
14
11

8037
9

794 1639 2476 3303 4132 4970 5792

55
50
45
39
34
28
23

6595
19

983 2029 3071 4101 5128 6161 7182

45
42
39
35
31
27
23

8184
20

794 1654 2509 3356 4196 5023 5830

74
69
64
58
52
46
40

6635
35

978 2037 3090 4136 5176 6207 7230

61
58
54
49
45
42
37

8234
33

783 1653 2517 3375 4224 5065 5895

93
88
83
76
70
64
58

6710
52

962 2030 3092 4144 5190 6231 7259

77
73
69
64
60
56
51

8271
47

762 1637 2514 3384 4245 5098 5940

131 126 120 113 106
99
92

6772
86

933 2005 3078 4141 5194 6239 7275

108 104
99
94
89
84
78

8298
73

731 1616 2499 3373 4239 5093 5936

170 164 157 150 142 135 127

6774
120

890 1972 3048 4112 5169 6213 7245

140 135 129 123 117 112 106

8271
100

12

677 1562 2455 3343 4217 5081 5934

228 221 213 205 196 188 179

6776
172

12

832 1912 2996 4071 5125 6163 7195

187 181 175 167 161 154 147

8224
140

15

613 1498 2389 3283 4169 5040 5907

285 278 269 260 251 242 232

6765
233

15

753 1832 2921 4009 5081 6137 7182

235 228 220 212 204 196 188

8212
180

20

448 1350 2245 3141 4031 4919 5798

381 373 363 353 342 331 321

6663
310

20

559 1654 2744 3834 4917 5991 7045

314 306 297 287 278 268 258

8081
248

25

334 1158 2044 2941 3837 4729 5612

477 468 457 445 433 421 409

6500
397

25

524 1427 2507 3595 4690 5780 6853

393 384 373 363 352 340 328

7913
317

761 1546 2326 3104

16
13
8
3

799 1638 2465 3270 4046 4813 5589

35
32
27
21
16
11
7

Flow (GPM)

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.

Flow (GPM)

PSLGC.PM6, dg, ki

65

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
G
S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0280

Code 0335

280 cc / rev

335 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

T
G
S
E
R
I
E
S

34.5

PRESSURE (BAR)

69.0 103.4 137.9 172.4 206.9 241.4 275.9

1.9

119.3 246.0 375.4 509.8

5
4
2
1

1.9

146.5 304.9 466.4 630.9

4
3
1
1

3.8

122.8 251.2 381.6 514.3 647.8 783.0 919.1 1056.4

12
10
8
6
5
3
3
2

3.8

150.2 309.7 471.8 636.1 800.4 966.11133.9 1298.8

10
8
7
5
4
2
2
1

7.6

127.0 261.3 396.9 531.0 664.3 797.6 930.8 1062.0

25
23
21
18
16
14
12
11

7.6

154.7 320.0 486.7 653.8 820.8 985.01145.2 1303.1

21
19
17
15
13
11
9
8

11.4

127.0 262.5 399.0 535.5 671.1 807.0 942.9 1077.4

39
36
34
31
28
25
22
19

11.4

154.3 320.6 488.8 657.2 824.9 992.11157.8 1320.2

32
30
27
25
22
20
17
14

15.1

127.2 265.1 403.1 540.7 678.3 815.0 950.7 1084.2

52
49
47
43
40
37
33
30

15.1

154.6 322.9 492.4 662.2 831.3 999.91165.6 1327.3

43
40
38
35
32
29
25
22

18.9

126.0 265.5 404.7 544.1 682.9 819.8 955.5 1089.2

65
62
59
56
52
49
45
41

18.9

153.1 322.9 493.5 664.3 834.51003.31169.61332.1

54
51
48
45
42
38
34
30

26.5

123.3 264.1 405.1 545.9 686.0 824.9 962.0 1096.6

92
88
85
80
76
72
67
63

26.5

149.5 320.9 492.9 665.2 836.81006.41173.21336.4

76
73
69
65
61
57
53
47

34.1

118.2 260.9 402.7 543.5 683.6 822.5 960.2 1096.7

118 114 110 105 101
96
90
85

34.1

143.0 315.3 488.8 661.6 833.31003.71171.81337.0

98
94
90
85
81
76
71
64

45.4

110.8 253.3 396.1 537.4 677.0 815.8 954.0 1090.5

159 154 148 143 137 132 125
118

45.4

133.0 304.8 477.9 650.7 821.7 991.21159.3 1324.8

131 127 121 116 110 105
98
90

56.8

101.5 244.5 388.3 531.2 672.3 812.0 950.8 1087.4

199 193 186 180 174 168 160
152

56.8

121.5 293.1 466.3 638.8 810.1 979.51147.1 1312.0

165 159 153 146 140 134 126
116

75.7

78.1 223.2 367.7 511.7 654.7 795.8 934.9 1073.2

266 258 250 243 235 227 218
209

75.7

94.1 268.0 442.3 617.2 791.8 964.11132.7 1296.9

221 214 205 197 189 182 173
161

94.6

79.4 195.0 337.5 481.3 625.9 770.0 911.9 1052.0

334 324 314 305 296 286 276
267

94.6

76.6 242.0 413.8 586.3 759.9 932.91102.3 1267.5

277 269 259 248 239 230 219
209

Flow (LPM)

17.1 cu in / rev
.5

TORQUE
SPEED

(nm)
(RPM)

PRESSURE (PSI)
500 1000 1500 2000 2500 3000 3500 4000
TORQUE
1056 2177 3323 4512
SPEED
5
4
2
1

770.0
286

Flow (LPM)

20.6 cu in / rev

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500 4000

(LB IN)
(RPM)

9350
2

.5

1297 2699 4128 5584

4
3
1
1

1087 2223 3378 4552 5734 6930 8135

12
10
8
6
5
3
3

9350
2

1329 2741 4176 5630 7084 8551 10036 11496

10
8
7
5
4
2
2
1

1124 2313 3513 4700 5880 7060 8239

25
23
21
18
16
14
12

9400
11

1369 2832 4308 5787 7265 8718 10136 11534

21
19
17
15
13
11
9
8

1124 2323 3532 4740 5940 7143 8346

39
36
34
31
28
25
22

9536
19

1366 2838 4326 5817 7301 8781 10248 11685

32
30
27
25
22
20
17
14

1126 2346 3568 4786 6004 7214 8415

52
49
47
43
40
37
33

9596
30

1368 2858 4358 5861 7358 8850 10317 11748

43
40
38
35
32
29
25
22

1115 2350 3582 4816 6044 7256 8457

65
62
59
56
52
49
45

9641
41

1355 2858 4368 5880 7386 8880 10352 11791

54
51
48
45
42
38
34
30

1091 2338 3586 4832 6072 7301 8515

92
88
85
80
76
72
67

9706
63

1323 2840 4363 5888 7407 8908 10384 11829

76
73
69
65
61
57
53
47

1046 2309 3564 4811 6051 7280 8499

118 114 110 105 101
96
90

9707
85

1266 2791 4326 5856 7376 8884 10372 11834

98
94
90
85
81
76
71
64

12

981 2242 3506 4757 5992 7221 8444

159 154 148 143 137 132 125

9652
118

12

1177 2698 4230 5759 7273 8773 10261 11726

131 127 121 116 110 105
98
90

15

898 2164 3437 4702 5951 7187 8416

199 193 186 180 174 168 160

9625
152

15

1075 2594 4127 5654 7170 8670 10153 11613

165 159 153 146 140 134 126 116

20

691 1976 3255 4529 5795 7044 8275

266 258 250 243 235 227 218

9499
209

20

833 2372 3915 5463 7008 8533 10026 11479

221 214 205 197 189 182 173 161

25

703 1726 2987 4260 5540 6815 8071

334 324 314 305 296 286 276

9311
267

25

678 2142 3663 5189 6726 8257 9757 11219

277 269 259 248 239 230 219 209

Flow (GPM)

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.

Flow (GPM)

PSLGC.PM6, dg, ki

66

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0405

405 cc / rev

24.7 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500 3000 3500

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4

1.9

174.4 359.1 546.8 736.1 924.7

4
3
2
1
1

3.8

180.0 367.9 556.8 746.5 938.11128.31316.4

8
7
6
6
5
4
3

1593 3256 4928 6607 8303 9987 11652

8
7
6
6
5
4
3

7.6

184.8 378.6 574.4 770.2 966.01160.51353.3

17
16
15
14
13
12
11

1636 3351 5084 6817 8550 10272 11978

17
16
15
14
13
12
11

11.4

184.9 380.2 576.9 773.6 970.31165.31359.3

27
25
23
22
21
19
18

1637 3365 5106 6847 8588 10314 12031

27
25
23
22
21
19
18

15.1

185.9 383.5 582.9 781.8 979.31175.21370.4

36
34
32
30
29
27
26

1645 3394 5159 6920 8668 10402 12130

36
34
32
30
29
27
26

18.9

185.3 385.0 587.6 788.9 986.71182.41377.7

45
43
41
39
37
35
33

1640 3408 5201 6983 8733 10466 12194

45
43
41
39
37
35
33

26.5

181.4 383.7 588.7 791.2 991.11189.31386.4

64
61
59
56
54
51
49

1606 3396 5211 7003 8772 10527 12271

64
61
59
56
54
51
49

34.1

175.2 378.5 584.8 788.7 990.01188.41386.2

82
80
77
73
70
67
64

1551 3350 5176 6981 8763 10519 12269

82
80
77
73
70
67
64

45.4

161.3 365.8 573.4 778.2 979.51177.71375.2

110 107 103
99
95
91
88

12

1428 3238 5075 6888 8670 10424 12172

110 107 103
99
95
91
88

56.8

148.0 351.6 559.0 763.6 965.41164.41362.5

138 135 130 125 120 115 111

15

1310 3112 4948 6759 8545 10306 12060

138 135 130 125 120
115 111

75.7

128.3 323.3 530.1 736.4 941.81143.61341.9

185 181 175 168 162 156 151

20

1136 2862 4692 6518 8336 10122 11877

185 181 175 168 162
156 151

94.6

507.5 712.1 913.31112.61308.9

219 212 204 197 190

25

4492 6303 8084 9848 11585

219 212 204
197 190

.5

1544 3178 4840 6515 8185

4
3
2
1
1

T
G

Flow (GPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

712.1
212

(LB IN)
(RPM)

9848
197

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

67

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0475

475 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9

T
G
S
E
R
I
E
S

29.1 cu in / revPRESSURE (PSI)

500 1000 1500 2000 2500 3000
1768 3732 5733 7744 9762
3
3
2
1
1

1.9

199.7 421.6 647.7 874.91102.9

3
3
2
1
1

3.8

211.0 438.1 664.2 887.01111.51336.6

7
7
6
5
4
3

1868 3878 5879 7851 9838 11830

7
7
6
5
4
3

7.6

221.9 458.1 698.2 930.61157.01371.1

15
14
14
12
10
8

1964 4055 6180 8237 10241 12136

15
14
14
12
10
8

11.4

222.8 460.3 701.4 940.11172.61395.9

23
22
21
19
17
13

1972 4074 6208 8321 10379 12355

23
22
21
19
17
13

15.1

226.5 467.2 710.3 947.01182.11411.8

31
30
29
27
24
20

2005 4135 6287 8382 10463 12496

31
30
29
27
24
20

18.9

226.4 466.5 712.2 952.21187.91417.2

39
38
37
34
31
26

2004 4129 6304 8428 10514 12544

39
38
37
34
31
26

26.5

224.8 466.9 712.7 954.11192.51423.8

55
54
52
50
45
40

1990 4133 6308 8445 10555 12602

55
54
52
50
45
40

34.1

217.4 463.7 710.1 952.41189.51424.5

70
69
68
65
60
54

1924 4104 6285 8430 10528 12608

70
69
68
65
60
54

45.4

200.5 449.0 695.6 940.91180.21415.4

94
93
91
87
82
75

12

1775 3974 6157 8328 10446 12528

94
93
91
87
82
75

56.8

182.9 427.5 676.8 925.11164.91397.8

118 116 114 110 104
96

15

1619 3784 5990 8188 10311 12372

118 116 114 110 104
96

75.7

148.5 381.1 636.0 887.21134.11372.1

157 156 153 149 141 132

20

1314 3373 5629 7853 10038 12145

157 156 153 149 141 132

94.6

128.9 342.2 589.8 839.11087.91328.3

197 196 193 189 182 174

25

1141 3029 5220 7427 9629 11757

197 196 193 189 182 174

113.6

68.5 283.0 525.2 764.41003.01241.5

237 236 233 230 224 219

30

606 2505 4649 6766 8878 10989

237 236 233 230 224
219

.5

Flow (LPM)

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

283.0
236

(LB IN)
(RPM)

6766
230

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

68

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0530

530 cc / rev

32.2 cu in / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4

PRESSURE (PSI)
500 1000 1500 2000 2500

1.9

235.0 480.8 732.0 985.91244.1

3
3
2
2
1

.5

2080 4256 6479 8726 11012

3
3
2
2
1

3.8

243.8 493.9 744.8 991.91242.1

7
6
6
5
4

2158 4372 6592 8779 10994

7
6
6
5
4

7.6

253.8 516.0 776.11031.11285.3

14
13
12
11
9

2246 4567 6869 9126 11376

14
13
12
11
9

11.4

253.3 517.2 781.41043.61299.3

21
20
19
17
14

2242 4578 6916 9237 11500

21
20
19
17
14

15.1

254.5 522.5 788.31050.31309.0

28
27
25
23
20

2253 4625 6977 9296 11586

28
27
25
23
20

18.9

252.5 523.0 791.11054.41313.5

35
34
32
29
26

2235 4629 7002 9333 11626

35
34
32
29
26

26.5

246.5 519.6 791.51057.71317.2

49
48
46
42
38

2182 4599 7006 9362 11659

49
48
46
42
38

34.1

236.7 512.4 786.31054.11316.2

63
62
59
55
50

2095 4535 6960 9330 11650

63
62
59
55
50

45.4

219.5 496.0 771.11041.31304.8

85
83
80
75
69

12

1943 4390 6825 9217 11549

85
83
80
75
69

56.8

198.1 474.4 750.01022.71288.9

106 104 100
95
87

15

1753 4199 6638 9052 11408

106 104 100
95
87

75.7

149.9 427.4 707.5 983.01252.5

141 139 135 129 120

20

1327 3783 6262 8701 11086

141 139 135 129 120

94.6

114.2 372.8 649.7 927.61202.0

177 175 171 165 158

25

1011 3300 5751 8210 10639

177 175 171 165 158

113.6

30.4 304.8 574.3 837.71108.8

213 211 208 203 197

30

269 2698 5083 7415 9814

213 211 208 203 197

Flow (LPM)

T
G

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

304.8
211

(LB IN)
(RPM)

9814
197

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

69

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0625

625 cc / rev

38.0 cu in /PRESSURE
rev
(PSI)

PRESSURE (BAR)
34.5 69.0 103.4 120.7 155.2

T
G
S
E
R
I
E
S

500 1000 1500 1750 2250

1939 4593
2
1

1.9

219.1 518.9
2
1

3.8

235.8 527.1 822.8 980.7 1308.2

5
3
2
2
1

2087 4665 7283 8680 11579

5
3
2
2
1

7.6

264.1 563.9 857.5 1000.2 1294.5

11
9
8
7
5

2338 4991 7590 8853 11458

11
9
8
7
5

11.4

269.6 576.3 875.9 1023.0 1320.6

17
15
13
12
9

2386 5101 7753 9055 11689

17
15
13
12
9

15.1

277.6 587.7 889.4 1036.5 1329.7

23
21
19
17
14

2457 5202 7872 9174 11769

23
21
19
17
14

18.9

280.1 592.7 897.4 1044.2 1335.5

29
27
25
23
18

2479 5246 7943 9242 11821

29
27
25
23
18

26.5

278.4 595.7 903.3 1051.4 1339.8

41
39
36
34
28

2464 5273 7995 9306 11859

41
39
36
34
28

34.1

271.3 590.1 903.0 1054.9 1348.4

53
51
48
45
39

2401 5223 7993 9337 11935

53
51
48
45
39

45.4

254.7 575.3 891.0 1043.8 1344.5

71
69
65
62
54

12

2254 5092 7886 9239 11900

71
69
65
62
54

56.8

231.8 553.7 872.3 1026.5 1329.0

89
87
83
80
70

15

2052 4901 7721 908611763

89
87
83
80
70

75.7

180.8 507.3 828.6 985.8 1290.7

120 117 112
109
98

20

1600 4490 7334 8725 11424

120 117 112 109
98

94.6

120.1 444.4 770.3 930.4 1245.2

151 148 144
140
131

25

1063 3933 6818 8235 11021

151 148 144 140 131

113.6

40.6 367.2 686.2 840.9 1150.0

182 180 176
172
165

30

359 3250 6074 7443 10179

182 180 176 172 165

.5

Flow (LPM)

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

367.2
180

(LB IN)
(RPM)

7443
172

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

70

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0785

785 cc / rev

48.0 cu in / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9

PRESSURE (PSI)
500 1000 1500 2000

1.9

328.8 695.2 1085.4 1463.1

2
2
1
1

.5

2910 6153 9607 12950

2
2
1
1

3.8

340.2 711.3 1092.5 1459.6

4
4
3
3

3011 6296 9670 12919

4
4
3
3

7.6

363.5 738.4 1122.5 1475.5

9
8
7
6

3217 6536 9935 13060

9
8
7
6

11.4

363.8 747.1 1127.2 1477.7

14
13
11
9

3220 6613 9977 13079

14
13
11
9

15.1

368.9 754.6 1132.2 1477.6

19
17
15
13

3265 6679 10021 13078

19
17
15
13

18.9

368.7 757.3 1135.1 1480.4

23
22
19
16

3263 6703 10047 13103

23
22
19
16

26.5

363.6 759.5 1137.5 1475.7

33
31
28
24

3218 6722 10068 13062

33
31
28
24

34.1

351.0 752.9 1142.0 1489.6

43
41
36
31

3107 6664 10108 13185

43
41
36
31

45.4

326.7 733.1 1125.2 1478.0

57
55
49
42

12

2892 6489 9959 13082

57
55
49
42

56.8

298.6 704.8 1099.6 1461.7

71
69
62
54

15

2643 6238 9733 12938

71
69
62
54

75.7

230.9 640.9 1043.8 1427.6

95
92
85
75

20

2044 5673 9239 12636

95
92
85
75

94.6

261.3 562.2 968.4 1364.0

119 117
110 101

25

2313 4976 8571 12073

119 117 110 101

113.6

56.0 463.7 856.6 1245.5

143 141
137 130

30

496 4104 7582 11024

143 141 137 130

Flow (LPM)

T
G

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

856.6
137

(LB IN) 11024

(RPM)
130

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

71

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Performance Data
Code 0960

58.5PRESSURE
cu in / rev
(PSI)

960 ccPRESSURE
/ rev
(BAR)
34.5

T
G
S
E
R
I
E
S

69.0 103.4

500 1000 1500

1.9

417.1 871.3 1327.5

2
1
1

.5

3692 7712 11750

2
1
1

3.8

428.0 887.8 1343.9

3
3
3

3788 7858 11895

3
3
3

7.6

440.6 908.9 1362.3

7
7
6

3900 8045 12058

7
7
6

11.4

441.2 912.7 1371.0

11
11
10

3905 8078 12135

11
11
10

15.1

445.0 921.4 1379.5

15
14
13

3939 8155 12210

15
14
13

18.9

443.2 923.4 1382.6

19
18
17

3923 8173 12238

19
18
17

26.5

436.1 921.9 1385.4

27
26
24

3860 8160 12262

27
26
24

34.1

421.8 912.2 1381.1

35
34
31

3733 8074 12224

35
34
31

45.4

392.6 886.7 1362.8

47
45
42

12

3475 7848 12062

47
45
42

56.8

355.8 852.4 1335.8

58
57
53

15

3149 7545 11823

58
57
53

75.7

275.3 773.1 1268.4

78
76
72

20

2437 6843 11227

78
76
72

94.6

335.4 676.8 1170.5

98
96
92

25

2969 5990 10360

98
96
92

30

603 4919 9170

118 117 113

113.6

68.1
118

555.7 1036.0
117 113

Flow (GPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

555.7
117

(LB IN)
(RPM)

9170
113

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

72

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Dimensional Data

Lengths & Weights

Inch equivalents for metric dimensions are shown in (**)

"L2"

"L1"

Wheel, Front Brake Nose Wheel,

Optional Wheel Mounts

Magneto, SAE "A", SAE "B" Mounts

T
G

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.
Rear Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.

Length "L" and Weight

Displacement, Code
Magneto &SAE "A"
mm
Length "L1"
(inches)
kg

Weight

(lb)

0140

0170

0195

0240

0280

0335

0405

0415

0530

0625

0785

0960

196
199
202
207
211
218
225
234
240
250
269
288
(7.70) (7.82) (7.95) (8.13) (8.32) (8.57) (8.86) (9.20) (9.45) (9.82) (10.57) (11.32)
14.2
(31.4)

14.5
14.7 15.1 15.5
(32.0) (32.5) (33.3) (34.2)

15.9
(35.1)

16.5
17.2
(36.4) (37.9)

17.9 18.6
20.2
(39.5) (41.1) (44.5)

21.9
(48.3)

SAE "B"
Length "L1"

mm
(inches)

189
192
195
200
205
211
219
227
233
243
262
281
(7.44) (7.56) (7.69) (7.87) (8.06) (8.31) (8.60) (8.94) (9.19) (9.56) (10.31) (11.06)

(lb)

14.9
(32.8)

15.2
15.3 15.7 16.1
(33.4) (33.9) (34.7) (35.6)

16.6
(36.5)

17.1
17.8
(37.8) (39.3)

18.6 19.3
20.8
(40.9) (42.5) (45.9)

22.5
(49.7)

Displacement, Code

0140

0170

0335

0405

0530

0960

(inches)

150
(5.92)

154
157
161
166
173
180
188
195
204
223
242
(6.04) (6.17) (6.35) (6.54) (6.79) (7.08) (7.42) (7.67) (8.04) (8.79) (9.54)

kg

Weight

0195

0240

0280

0415

0625

0785

Wheel & Brake

Mount
mm
Length "L2"

Weight

kg

14.6

(lb)

14.8

15.1

15.5

15.9

16.3

(37.7) (33.3) (34.1) (35.0)

(35.8)

16.9

17.5

(32.2)

mm

178
181
184
189
193
200
207
216
222
232
251
270
(6.99) (7.11) (7.24) (7.43) (7.61) (7.86) (8.15) (8.49) (8.74) (9.12) (9.87) (10.62)

(37.2) (38.6)

18.3

19.0

20.5

22.2

(40.3) (41.8) (45.3)

(49.0)

Optional Wheel
Mount
Length "L2"

(inches)
Weight

kg
(lb)

17.6
(38.7)

17.8
18.1 18.4 18.8
(39.3) (39.8) (40.6) (41.5)

19.3
(42.4)

19.8
20.5
(43.7) (45.2)

21.3 22.0
23.5
(46.8) (48.4) (51.8)

PSLGC.PM6, dg, ki

73

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

25.2
(55.6)

S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Dimensional Data

Mounting
Inch equivalents for metric dimensions are shown in (**)
15.7 (.62)
62.81
(2.473)

2.79 (.110)

SAE "A" 2 Bolt Flange

82.55
(3.250)

T
G
S
E
R
I
E
S

2X 13.5 (17/32) on a
106.38 (4.188) BC

65.3 (2.57)

2 x 14.29 (9/16) thru holes

on a 146.05 (5.750) BC

9.4 (.37)

15.7 (.62)

SAE "B" 2 Bolt Flange

174.5 (6.87)

101.57 (3.999)

62.81 (2.473)
15.7 (.62)

22 30'

2.8 (.11)

82.52 (3.249)
133.4 (5.25)

4 Bolt Magneto

4 x 13.49 (17/32) thru holes

on a 106.38 (4.188) BC
45

PSLGC.PM6, dg, ki

74

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Dimensional Data

Mounting, Wheel
Inch equivalents for metric dimensions are shown in (**)

46.7 (1.84)
63.83 (2.513)
36.8
(1.45)

4.1 (.16) Min

19.0 (.75)

39.9 (1.57)

45

40.1 (1.58) Max

Wheel

62.99 82.52
(2.480) (3.249)

25.4 (1.00)
25.4 (1.00)

4X 13.5 (17/32) equally spaced

on a 147.62 (5.182) Bolt Circle

.16 (4.1)
Min

36.8 (1.45)
46.7 (1.84)

45

126.95 ( 4.998)
88.85 (3.498)

Wheel, Front Brake Nose

4 x 13.49 (17/32) thru

holes on a 147.62 ( 5.812)
Bolt Circle

19.1 (.75)

44.2 (1.74)

4 x 5/16-18 UNC thd equally

spaced on a 76.20 ( 3.000)
Bolt Circle

45

4.8 (.19) Min

36.1 (1.42) Max

107.90 (4.248)

126.95 ( 4.998)

Wheel, Optional

95.3 (3.75)
Ref

4 x 13.49 (17/32) thru

holes on a 147.62 ( 5.812)
Bolt Circle

PSLGC.PM6, dg, ki

75

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
G
S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Dimensional Data

Porting
Inch equivalents for metric dimensions are shown in (**)

SAE O-Ring & BSPF

Manifold
64.3
(2.53)

64.3
(2.53)

31.75 (1.250)

22.86 (.900)

63.50 (2.500)
25.40 (1.000)

T
G

14.27 (.562)
28.58 (1.125)

7/8-14 SAE O-Ring

or
1/2" BSPF

Rear Ports

62.99 (2.480)

65.53 (2.580)
7/8-14 SAE O-Ring

22.86 (.900)

A
129.5
(5.10)

7/8-14 SAE O-Ring

B

S
E
R
I
E
S

45.72 (1.800)

4 x 5/16-18 UNC thd

x .500 min deep

45.72 (1.800)

14.27 (.562)
65.53 (2.580)
28.58 (1.125)
22.86 (.900)

A
63.50 (2.500)

Manifold

45.72 (1.800)
31.75 (1.250)
4 x 5/16-18 UNC thd
x .50 Min Deep

Consult Factory for

ISO 6149 Porting

PSLGC.PM6, dg, ki

76

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Dimensional Data

Shafts
Inch equivalents for metric dimensions are shown in (**)

48.8 (1.92)

60.2 (2.37)

25.65 ( 1.010)
x 6.38 (.251) Wide

2.8 (.11)

36.50 (1.437)
x 7.90 (.311)

50.3 (1.98)

38.33 (1.509)
4.3 (.17)

4.22 (.166)

27.99 (1.102)
25.40 (1.000)

1.24 (.049)

37.34 (1.470)

34.90 (1.374)

23.52 (.926)

5/8-18 UNF thd

x 19.1 (.75) Min Deep

19.00 (.748)
Keyway Center Line

59.9 (2.36)

1 1/4" Keyed

2.8 (.11)

T
G

4.29 (.169)

34.91 (1.374)

61.7 (2.43)
35.1 (1.38)
7.90 (.311)
Woodruff Key

5/8-18 UNF thd

x 19.1 (.75) Min Deep

70.1
(2.76)

41.4 (1.63)

Key Width .311

7.90 (.311)
Woodruff Key

1 3/8" Keyed

1.000-20 UNEF thd

1.125-18 UNEF thd

38.10 Taper per Meter

(1.500 Taper per Foot)

38.0 (1.5)
Taper Per Ft.

1 3/8" Taper

1 1/4" Taper

48.8 (1.92)
4.3 (.17)
2.8 (.11)

57.4 (2.26)*
37.34 (1.47)

47.2
(1.86)

1.24 (.049)

25.40 (1.00) Min. Full Spline

23.52 (.926)

31.75 (1.250)
27.31 (1.075)

25.40 (1.00) Min. Full Spline

* Add .26" for SAE B Mount

Add 1.78" for Wheel Mount
Add 1.68" for Optional Wheel Mount

5/8-18 UNF thd

x 19.1 (.75) Min Deep

1 1/4" 14 Tooth Spline

1" 6B Spline
PSLGC.PM6, dg, ki

77

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Speed Sensor

An Economical Sensor for Speed

Readout
This rugged, weather resistant speed sensor is a
Hall effect device. When externally powered, 30
square wave digital pulses per output shaft revolution are produced. By signal multiplication, 60
pulses per revolution can be obtained.
The installation of this economical sensor does not
affect the torque or side load capability of the
TorqlinkTM motor into which it is installed.

T
G

Features
Operating Voltage Range .......... 4.5 to 24 VDC

S
E
R
I
E
S

2
N/C

1
+

3
-

4
Output

Operating Temperature ............. -40 C to 93 C

(-40 F to 200 F)
Operating Frequency Range ..... 0 to 100 KHZ
Maximum Sink Current ............. 20 mA
Connection ................................ DC Din Standard
4 Pin Micro-Mini
Pin Diameter ............................. 12mm
Sensor Output ........................... 30 Pulses per
Revolution which can be doubled electronically.
Pull-up Resistor Value Formula
(for 1/4 Watt, 5% Tolerance)
V Supply (4.5-24 VDC)

= Resistor Value
Desired Sink Current (0-20 mA 20%)
(K - Ohms)

+ 4.5 to 24 VDC

Pin # 4

Output

Pin # 3

- Negative

Pin # 2

No Connection

SENSOR

On State Current: 5 mA
Higher wattage resistor will be needed for higher
sink current.

+V Off State

Pin # 1

Min Off State = .95%+V

On State Max On State = .400VDC

0V

Cable not included

PSLGC.PM6, dg, ki

78

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series

Catalog 1510-20

Ordering Information

TG

XXXX

Series

Displacement

Mounting

Porting

Code Displacement
0140
0170
0195
0240
0280
0335
0405
0475
0530
0625
0785
0960

08.6
10.3
11.9
14.5
17.1
20.6
24.7
29.1
32.3
38.0
48.0
58.5

Code
A
B
M
U
L
W*
*

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Code
A
B
E
J
M*
S
T**

Code

Not available on L, U or W mounting

Available on A & M mounting only

Requires rear porting

01
02
03
04
05
06
07
08
19
20

Porting

**

SAE "A" 2-Bolt

SAE "B" 2-Bolt
Magneto
Wheel; Standard
Wheel; Front Brake Nose
Wheel, Optional

Shaft
1"6B Spline
1" Keyed
1 1/4" Keyed
10B Spline
1 1/4" 14 Tooth Spline
19 Tooth Spline
15 Tooth Spline
1 1/4" Tapered
1 3/8" Tapered
1 3/8" Keyed

Code
AAAA
AAAB
AAAC
AAFC
AAAF***
AABP***
AAAG
AAAH
AAHD
AAAJ
AAFG
AAAT*
AAFX*
AAAU*
AAGF*
AABJ****
AABK****
AABL****
AABM****
BBBA*
BBBM*
BBBG*
BBBJ*
BBBB*
BBBN*
BBBK*
BBBC*
BBBF*
BBBD*
BBBW*
FFAA
FFAB
FFAH
FFAJ
*
**
***
****

PSLGC.PM6, dg, ki

79

Hydraulics

Shaft

7/8"-14 SAE O-Ring; Rear Axial

7/8"-14 SAE O-Ring; Rear Radial
Manifold; Rear Radial
ISO 6149 M22x1.5
Manifold
7/8"-14 SAE O-Ring
1/2" BSPF

Mounting

Code

XX

0
1

XXXX

Rotation

Options

Rotation
Standard
Reverse Timed Manifold

Options
Black Paint
No Paint
Double Paint
White Epoxy Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Viton Seals, White Epoxy Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Bidirectional Shuttle (11:00**), Black Paint
Bidirectional Shuttle (11:00**), No Paint
Bidirectional Shuttle (11:00**), Castle Nut, Black Paint
Bidirectional Shuttle (11:00**), Castle Nut, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
1000 PSI Internal Bidirectional Relief, Black Paint
1000 PSI Internal Bidirectional Relief, No Paint
1500 PSI Internal Bidirectional Relief, Black Paint
1500 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Black Paint
2000 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Castle Nut, Black Paint
3000 PSI Internal Bidirectional Relief, Black Paint
3000 PSI Internal Bidirectional Relief, No Paint
4000 PSI Internal Bidirectional Relief, Black Paint
4000 PSI Internal Bidirectional Relief, No Paint
Internal Speed Sensor, Black Paint
Internal Speed Sensor, No Paint
Internal Speed Sensor, Castle Nut, No Paint
Internal Speed Sensor, Castle Nut, Black Paint

Not available with A, B or E porting

Shuttle port position as viewed from shaft end of motor
Available only with shaft code 08 & 19
Not available on 0625, 0785 or 0960 displacement codes

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
G
S
E
R
I
E
S

Low Speed High Torque Motors

TG Series Brake Motor

Catalog 1510-20

Technical Information

Brake Motor
This motor/brake combination consists of a TG
Series motor built into a front mounted brake. The
brake is a wet disc, spring set, hydraulically released
unit. When hydraulic pressure is absent at the pilot
port of the brake, internal springs will hold against
10,200 lb in of torque. The brake will start to release
when 360 PSI is present in the brake pilot port and
will be fully disengaged when that pressure reaches
460 PSI. The pilot port is capable of withstanding
the maximum operating pressure of the TG Series
motor.

T
G
S
E
R
I
E
S

Dimensions
Inch equivalents for metric dimensions are shown in (**)

218.4 (8.60)

"L"

7/16-20 Straight THD

O-Ring Ports 2 PL
1 Pressure Port
1 Bleed Port

6.4 (.25)

PSLGC.PM6, dg, ki

80

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TG Series Brake Motor

Catalog 1510-20

Ordering Information

TG

XXXX

Series

Displacement

Mounting

Porting

Code Displacement
0140
0170
0195
0240
0280
0335
0405
0475
0530
0625
0785
0960

08.6
10.3
11.9
14.5
17.1
20.6
24.7
29.1
32.3
38.0
48.0
58.5

Code
8

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Code
A
B
S

Mounting
Wheel Brake

Code
03
05
08
31
32
36

Shaft
1
1
1
1
1
1

1/4"
1/4"
1/4"
1/2"
1/2"
1/2"

Keyed
14 Tooth Spline
Tapered
Tapered
Keyed
17 Tooth Spline

XX
Shaft

Porting

Code

7/8"-14 SAE O-Ring; Rear Axial

7/8"-14 SAE O-Ring; Rear Radial
7/8"-14 SAE O-Ring; Front Radial

Code
AAAA
AAAB
AAAC
AAFC
AAAF***
AABP***
AAAG
AAAH
AAHD
AAAJ
AAFG
AAAT*
AAFX*
AAAU*
AAGF*
AABJ****
AABK****
AABL****
AABM****
BBBA*
BBBM*
BBBG*
BBBJ*
BBBB*
BBCC*
BBBK*
BBBC*
BBBF*
BBBD*
BBBW*
*
**
***
****

0
1

XXXX

Rotation

Options

Rotation
Standard
Reverse Timed Manifold

Options
Black Paint
No Paint
Double Paint
White Epoxy Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Viton Seals, White Epoxy Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Bidirectional Shuttle (11:00**), Black Paint
Bidirectional Shuttle (11:00**), No Paint
Bidirectional Shuttle (11:00**), Castle Nut, Black Paint
Bidirectional Shuttle (11:00**), Castle Nut, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
1000 PSI Internal Bidirectional Relief, Black Paint
1000 PSI Internal Bidirectional Relief, No Paint
1500 PSI Internal Bidirectional Relief, Black Paint
1500 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Black Paint
2000 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Castle Nut, Black Paint
3000 PSI Internal Bidirectional Relief, Black Paint
3000 PSI Internal Bidirectional Relief, No Paint
4000 PSI Internal Bidirectional Relief, Black Paint
4000 PSI Internal Bidirectional Relief, No Paint

Not available with A or B porting

Shuttle port position as viewed from shaft end of motor
Available only with shaft code 08 or 31
Not available on 0625, 0785, or 0960 displacement codes

PSLGC.PM6, dg, ki

81

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
G
S
E
R
I
E
S

Low Speed High Torque Motors

TG Series Brake Motor

Catalog 1510-20

Technical Information

Dimensions
Inch equivalents for metric dimensions are shown in (**)

4.8 (.19)

T
G

2 x 7/8-14 SAE
O-Ring
21.6 (.85)
This dimension
applies to both ports.

Rear View

S
E
R
I
E
S

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.
Rear Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.

4 x 13.5 (.531) On
171.42 (6.749) BC Spotface
20.3 (.80)

45

196.8 (7.75)

Front View
PSLGC.PM6, dg, ki

82

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Technical Information

A Rugged Motor for Heavy Duty,

High Side Load Applications
This motor was designed for tough applications. A
stout drive link with patented 60:40 spline
geometry will transmit over 13000 lb in of torque.
The 1 1/2 output shaft can support 7000 lb of
axial load. Efficiency is assured by use of roller
vanes and sealed commutator. Durability is
maintained by continually washing the powertrain
splines and shaft seal in cooling fluid.

Options

Features

1 1/2 inch Keyed, Splined or Tapered Shafts

Roller Bearings - For Heavy Radial Loads

Wheel or 4 Bolt Magneto Mounting

SAE O-Ring or Manifold Porting

Roller Vane Power Element - For High Volumetric Efficiency and Long Life

Front or Rear Porting

Orbiting Commutator - For Accurate Timing,

Smooth Low Speed Operation

Internal Cross - Over Relief Valves

Hot Oil Shuttle

Full Flow Spline Lubrication - For Extended

Spline Life

Free Running Rotor Set

High Pressure Shaft Seal - For High Back

Pressure Operation Without External Drain Lines

Reverse Timed Manifold

Corrosion Resistance

High Flow Shaft Seal Cooling - For Long Seal

Life

60:40 Spline Geometry - For Superior Powertrain Strength, Long Life

Robust Construction - For Quiet operation

T
H

TH Specifications
Code
Displacement

0140

0170

0195

0240

0280

0335

140
(8.6)

169
(10.3)

195
(11.9)

237
(14.5)

280
(17.1)

337
(20.6)

405
(24.7)

476
(29.1)

528

442

381

314

266

221

185

bar
(psid)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

206.9
(3000)

bar
(psid)

275.9
(4000)

275.9
(4000)

275.9
(4000)

275.9
(4000)

275.9
(4000)

406.8
(3601)

494.9
(4380)

576.0
(5098)

704.9
(6239)

824.9
(7301)

541.6
(4794)

659.6
(5838)

765.6
(6776)

937.5 1096.7 1337.0 1386.4 1424.5 1317.2 1348.4 1489.6 1385.4

(8298) (9707) (11834) (12271) (12608) (11659) (11935) (13185) (12262)

cc/rev
(cu in/rev)

Maximum Speed (rpm) @

Maximum Continuous Flow
Pressure Differential
Maximum Continuous
Maximum Intermittent

Max. Torque @ Max. Continuous

Pressure
nm
(lb-in)
Max. Torque @ Max. Intermittent
Pressure
nm
(lb-in)

0405

0475

0530

0625

0785

0960

529
(32.3)

624
(38.0)

786
(48.0)

958
(58.5)

157

141

120

95

78

172.4
(2500)

137.9
(2000)

137.9
(2000)

120.7
(1750)

103.4
(1500)

69.0
(1000)

275.9
(4000)

241.4
(3500)

206.9
(3000)

172.4
(2500)

155.2
(2250)

137.9
(2000)

103.4
(1500)

1006.4
(8908)

991.1
(8772)

954.1 1057.7 1054.9 1142.0

(8445) (9362) (9337) (10108)

923.4
(8173)

PSLGC.PM6, dg, ki

83

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Technical Information

Maximum Side Load Capacity

Performance Data

Flange Mount
Side Load - kg (lb)
3628.8
(8000)

Continuous / Intermittent* Operation

Continuous

2721.6
(6000)

Intermittent*
1814.4
(4000)

*Intermittent operation is defined as less

than 10% per minute.

907.2
(2000)

-25.4 0
(-1) (0)

Performance data based on testing using 10W40 oil

with a viscosity of 200 SUS at 54 C (130 F.)

25.4 50.8 76.2 101.6 127.0

(1)
(2)
(3)
(4) (5)

Performance data is typical. Actual data may vary

slightly from one production motor to another.

Distance From Mounting Face - mm (in)

Wheel Mount
Side Load - kg (lb)
3628.8
(8000)

2721.6
(6000)

1814.4
(4000)

T
H
S
E
R
I
E
S

907.2
(2000)

0
-25.4 0
25.4 50.8 76.2 101.6 127.0 152.4
(-1) (0)
(1)
(2)
(3)
(4)
(5)
(6)
Distance From Mounting Face - mm (in)

B-10 Life Factors

Application of the
above uni-directional
radial loads will
result in a B-10 life of
3 million revolutions.
For B-10 life at other
radial loads, apply
the factors from the
curve to the right.

Multiply
3
Allowable
Radial Load
By These
2
Factors
1
0

0 2 4 6 8 10 12
Life In Millions Of Revolutions
PSLGC.PM6, dg, ki

84

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0140

Code 0170

140 cc / rev

170 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

PRESSURE (BAR)

34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

1.9

58.6 119.8
9
4

1.9

70.0 145.1 219.7 295.2 372.0 450.0

9
7
5
4
3
2

3.8

61.0 123.1 184.7 246.3

22
17
11
6

3.8

73.7 151.1 226.6 303.1 381.3 459.0 536.0 610.3

20
18
16
14
12
11
8
8

7.6

64.3 130.6 195.5 258.3 319.4 380.5 440.5 502.4

49
43
36
30
23
19
12
12

7.6

76.6 157.0 237.8 318.8 399.4 477.5 554.6 631.2

42
40
37
35
32
30
27
25

11.4

63.8 130.9 197.0 262.2 327.5 392.8 457.3 520.6

75
69
62
55
47
40
33
29

11.4

76.6 157.8 239.2 320.4 401.5 481.6 560.7 638.6

64
61
58
56
53
50
46
44

15.1

63.7 132.2 199.7 266.4 332.5 397.4 461.2 524.7

102
94
87
80
72
64
57
52

15.1

76.7 159.2 242.0 324.5 406.3 486.9 567.3 645.8

86
83
80
77
74
71
67
64

18.9

62.8 132.2 200.7 268.3 335.3 401.8 467.2 531.1

128 120 112 105
97
89
81
76

18.9

76.3 159.6 242.9 325.9 408.5 490.2 571.3 650.9

108 104 101
98
94
91
87
83

26.5

61.0 131.1 201.0 270.0 338.3 405.8 472.4 538.1

182 172 164 155 146 138 130
123

26.5

74.7 158.7 243.1 327.6 411.5 494.2 576.3 657.3

153 148 143 140 136 132 127
123

34.1

58.2 129.1 199.7 269.5 338.5 406.8 474.4 541.6

235 225 215 206 196 187 179
171

34.1

71.4 156.5 241.8 326.6 411.0 494.9 577.8 659.6

197 191 186 181 177 173 168
163

45.4

53.2 123.8 195.3 266.2 336.0 405.3 473.7 541.6

315 303 292 281 271 261 252
243

45.4

65.9 150.7 236.8 323.1 408.6 492.8 576.3 657.9

263 256 250 244 239 234 228
223

56.8

47.2 117.7 189.0 260.6 331.4 401.0 470.3 539.0

395 381 368 357 346 336 325
314

56.8

59.2 144.0 229.9 316.8 403.6 488.9 572.8 655.4

330 322 314 308 302 296 289
283

75.7

33.8 105.2 176.8 248.3 319.2 390.3 460.7 530.1

528 512 497 484 472 459 447
435

75.7

43.2 129.1 215.6 303.1 390.3 476.3 561.7 645.6

442 432 422 413 406 399 391
383

94.6

19.5 89.7 161.1 232.6 304.5 376.4 447.5 517.3

660 643 626 612 598 583 569
555

94.6

27.0 111.1 197.4 285.0 372.7 459.9 546.7 631.7

554 543 531 520 511 501 492
483

Flow (LPM)

TORQUE
SPEED

8.6 cu in / rev

Flow (LPM)

304.5
598

10.3 cu in / rev

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

.5

(nm)
(RPM)

519 1060
9
4

540 1090 1635 2180

22
17
11
6

569 1156 1730 2286 2827 3368 3899

49
43
36
30
23
19
12

4000
TORQUE
SPEED

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

(LB IN)
(RPM)

3899
12

.5

4000

620 1284 1945 2613 3293 3983

9
7
5
4
3
2

652 1337 2006 2683 3375 4063 4744

20
18
16
14
12
11
8

5402
8

4447
12

678 1390 2105 2822 3535 4226 4909

42
40
37
35
32
30
27

5587
25

565 1159 1744 2321 2899 3477 4048

75
69
62
55
47
40
33

4608
29

678 1397 2117 2836 3554 4263 4963

64
61
58
56
53
50
46

5652
44

564 1170 1768 2358 2943 3517 4082

102
94
87
80
72
64
57

4644
52

679 1409 2142 2872 3596 4310 5021

86
83
80
77
74
71
67

5716
64

556 1170 1776 2375 2968 3556 4135

128 120 112 105
97
89
81

4701
76

675 1413 2150 2885 3616 4339 5057

108 104 101
98
94
91
87

5761
83

540 1160 1779 2390 2994 3592 4181

182 172 164 155 146 138 130

4763
123

661 1405 2152 2900 3642 4374 5101

153 148 143 140 136 132 127

5818
123

515 1143 1768 2385 2996 3601 4199

235 225 215 206 196 187 179

4794
171

632 1385 2140 2891 3638 4380 5114

197 191 186 181 177 173 168

5838
163

12

471 1096 1729 2356 2974 3587 4193

315 303 292 281 271 261 252

4794
243

12

583 1334 2096 2860 3617 4362 5101

263 256 250 244 239 234 228

5823
223

15

418 1042 1673 2307 2933 3549 4163

395 381 368 357 346 336 325

4771
314

15

524 1275 2035 2804 3572 4327 5070

330 322 314 308 302 296 289

5801
283

20

299
528

931 1565 2198 2825 3455 4078

512 497 484 472 459 447

4692
435

20

382 1143 1908 2683 3455 4216 4972

442 432 422 413 406 399 391

5714
383

25

173
660

794 1426 2059 2695 3332 3961

643 626 612 598 583 569

4579
555

25

239
554

5591
483

Flow (GPM)

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.

983 1747 2523 3299 4071 4839

543 531 520 511 501 492

Flow (GPM)

PSLGC.PM6, dg, ki

85

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
H
S
E
R
I
E
S

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0195

Code 0240

195 cc / rev

240 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

1.9

82.8 169.8
7
3

1.9

105.3 215.5 327.0

6
4
2

3.8

86.0 174.7 262.8 350.7

16
13
8
3

3.8

108.5 220.8 333.3 445.5 558.0 670.0

14
12
9
6
3
2

7.6

90.3 185.1 278.5 369.4 457.1 543.8 631.4 720.2

35
32
27
21
16
11
7
6

7.6

111.6 229.5 346.3 462.1 577.0 689.2 798.5 908.0

30
27
24
20
17
14
11
9

11.4

89.7 185.2 279.7 373.2 466.8 561.5 654.4 745.1

55
50
45
39
34
28
23
19

11.4

111.1 229.2 347.0 463.3 579.4 696.1 811.4 924.6

45
42
39
35
31
27
23
20

15.1

89.7 186.9 283.5 379.2 474.1 567.5 658.7 749.6

74
69
64
58
52
46
40
35

15.1

110.5 230.1 349.1 467.3 584.8 701.3 816.8 930.3

61
58
54
49
45
42
37
33

18.9

88.5 186.8 284.4 381.3 477.2 572.2 666.0 758.1

93
88
83
76
70
64
58
52

18.9

108.7 229.3 349.3 468.2 586.4 704.0 820.1 934.5

77
73
69
64
60
56
51
47

26.5

86.1 184.9 284.0 382.3 479.6 576.0 671.1 765.1

131 126 120 113 106
99
92
86

26.5

105.4 226.5 347.8 467.9 586.8 704.9 821.9 937.5

108 104
99
94
89
84
78
73

34.1

82.6 182.6 282.3 381.1 478.9 575.4 670.6 765.3

170 164 157 150 142 135 127
120

34.1

100.6 222.8 344.4 464.6 584.0 701.9 818.5 934.5

140 135 129 123 117 112 106
100

45.4

76.5 176.5 277.4 377.7 476.4 574.1 670.4 765.6

228 221 213 205 196 188 179
172

45.4

94.0 216.0 338.5 459.9 579.0 696.3 812.9 929.1

187 181 175 167 161 154 147
140

56.8

69.3 169.2 269.9 370.9 471.0 569.4 667.4 764.3

285 278 269 260 251 242 232
233

56.8

85.1 207.0 330.0 452.9 574.1 693.4 811.4 927.8

235 228 220 212 204 196 188
180

75.7

50.6 152.5 253.6 354.9 455.4 555.7 655.1 752.8

381 373 363 353 342 331 321
310

75.7

63.2 186.9 310.0 433.2 555.5 676.9 795.9 913.0

314 306 297 287 278 268 258
248

94.6

37.7 130.8 230.9 332.3 433.5 534.3 634.0 734.4

477 468 457 445 433 421 409
397

94.6

59.2 161.2 283.2 406.2 529.9 653.0 774.3 894.0

393 384 373 363 352 340 328
317

Flow (LPM)

11.9 cu in / rev

TORQUE
SPEED

.5

S
E
R
I
E
S

733 1503
7
3

(nm)
(RPM)

534.3
421

Flow (LPM)

14.5 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500 3000 3500 4000

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500

T
H

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

4000

TORQUE
SPEED

(LB IN)
(RPM)

4813
11

.5

932 1907 2894

6
4
2

960 1954 2950 3943 4939 5930

14
12
9
6
3
2

6375
6

988 2031 3065 4090 5107 6100 7068

30
27
24
20
17
14
11

8037
9

794 1639 2476 3303 4132 4970 5792

55
50
45
39
34
28
23

6595
19

983 2029 3071 4101 5128 6161 7182

45
42
39
35
31
27
23

8184
20

794 1654 2509 3356 4196 5023 5830

74
69
64
58
52
46
40

6635
35

978 2037 3090 4136 5176 6207 7230

61
58
54
49
45
42
37

8234
33

783 1653 2517 3375 4224 5065 5895

93
88
83
76
70
64
58

6710
52

962 2030 3092 4144 5190 6231 7259

77
73
69
64
60
56
51

8271
47

762 1637 2514 3384 4245 5098 5940

131 126 120 113 106
99
92

6772
86

933 2005 3078 4141 5194 6239 7275

108 104
99
94
89
84
78

8298
73

731 1616 2499 3373 4239 5093 5936

170 164 157 150 142 135 127

6774
120

890 1972 3048 4112 5169 6213 7245

140 135 129 123 117 112 106

8271
100

12

677 1562 2455 3343 4217 5081 5934

228 221 213 205 196 188 179

6776
172

12

832 1912 2996 4071 5125 6163 7195

187 181 175 167 161 154 147

8224
140

15

613 1498 2389 3283 4169 5040 5907

285 278 269 260 251 242 232

6765
233

15

753 1832 2921 4009 5081 6137 7182

235 228 220 212 204 196 188

8212
180

20

448 1350 2245 3141 4031 4919 5798

381 373 363 353 342 331 321

6663
310

20

559 1654 2744 3834 4917 5991 7045

314 306 297 287 278 268 258

8081
248

25

334 1158 2044 2941 3837 4729 5612

477 468 457 445 433 421 409

6500
397

25

524 1427 2507 3595 4690 5780 6853

393 384 373 363 352 340 328

7913
317

761 1546 2326 3104

16
13
8
3

799 1638 2465 3270 4046 4813 5589

35
32
27
21
16
11
7

Flow (GPM)

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.

Flow (GPM)

PSLGC.PM6, dg, ki

86

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0280

Code 0335

280 cc / rev

335 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4 275.9

34.5

PRESSURE (BAR)

69.0 103.4 137.9 172.4 206.9 241.4 275.9

1.9

119.3 246.0 375.4 509.8

5
4
2
1

1.9

146.5 304.9 466.4 630.9

4
3
1
1

3.8

122.8 251.2 381.6 514.3 647.8 783.0 919.1 1056.4

12
10
8
6
5
3
3
2

3.8

150.2 309.7 471.8 636.1 800.4 966.11133.9 1298.8

10
8
7
5
4
2
2
1

7.6

127.0 261.3 396.9 531.0 664.3 797.6 930.8 1062.0

25
23
21
18
16
14
12
11

7.6

154.7 320.0 486.7 653.8 820.8 985.01145.2 1303.1

21
19
17
15
13
11
9
8

11.4

127.0 262.5 399.0 535.5 671.1 807.0 942.9 1077.4

39
36
34
31
28
25
22
19

11.4

154.3 320.6 488.8 657.2 824.9 992.11157.8 1320.2

32
30
27
25
22
20
17
14

15.1

127.2 265.1 403.1 540.7 678.3 815.0 950.7 1084.2

52
49
47
43
40
37
33
30

15.1

154.6 322.9 492.4 662.2 831.3 999.91165.6 1327.3

43
40
38
35
32
29
25
22

18.9

126.0 265.5 404.7 544.1 682.9 819.8 955.5 1089.2

65
62
59
56
52
49
45
41

18.9

153.1 322.9 493.5 664.3 834.51003.31169.6 1332.1

54
51
48
45
42
38
34
30

26.5

123.3 264.1 405.1 545.9 686.0 824.9 962.0 1096.6

92
88
85
80
76
72
67
63

26.5

149.5 320.9 492.9 665.2 836.81006.41173.2 1336.4

76
73
69
65
61
57
53
47

34.1

118.2 260.9 402.7 543.5 683.6 822.5 960.2 1096.7

118 114 110 105 101
96
90
85

34.1

143.0 315.3 488.8 661.6 833.31003.71171.8 1337.0

98
94
90
85
81
76
71
64

45.4

110.8 253.3 396.1 537.4 677.0 815.8 954.0 1090.5

159 154 148 143 137 132 125
118

45.4

133.0 304.8 477.9 650.7 821.7 991.21159.3 1324.8

131 127 121 116 110 105
98
90

56.8

101.5 244.5 388.3 531.2 672.3 812.0 950.8 1087.4

199 193 186 180 174 168 160
152

56.8

121.5 293.1 466.3 638.8 810.1 979.51147.1 1312.0

165 159 153 146 140 134 126
116

75.7

78.1 223.2 367.7 511.7 654.7 795.8 934.9 1073.2

266 258 250 243 235 227 218
209

75.7

94.1 268.0 442.3 617.2 791.8 964.11132.7 1296.9

221 214 205 197 189 182 173
161

94.6

79.4 195.0 337.5 481.3 625.9 770.0 911.9 1052.0

334 324 314 305 296 286 276
267

94.6

76.6 242.0 413.8 586.3 759.9 932.91102.3 1267.5

277 269 259 248 239 230 219
209

Flow (LPM)

17.1 cu in / rev
.5

TORQUE
SPEED

(nm)
(RPM)

PRESSURE (PSI)
500 1000 1500 2000 2500 3000 3500 4000
TORQUE
1056 2177 3323 4512
SPEED
5
4
2
1

770.0
286

Flow (LPM)

20.6 cu in / rev

PRESSURE (PSI)

500 1000 1500 2000 2500 3000 3500 4000

(LB IN)
(RPM)

9350
2

.5

1297 2699 4128 5584

4
3
1
1

1087 2223 3378 4552 5734 6930 8135

12
10
8
6
5
3
3

9350
2

1329 2741 4176 5630 7084 8551 10036 11496

10
8
7
5
4
2
2
1

1124 2313 3513 4700 5880 7060 8239

25
23
21
18
16
14
12

9400
11

1369 2832 4308 5787 7265 8718 10136 11534

21
19
17
15
13
11
9
8

1124 2323 3532 4740 5940 7143 8346

39
36
34
31
28
25
22

9536
19

1366 2838 4326 5817 7301 8781 10248 11685

32
30
27
25
22
20
17
14

1126 2346 3568 4786 6004 7214 8415

52
49
47
43
40
37
33

9596
30

1368 2858 4358 5861 7358 8850 10317 11748

43
40
38
35
32
29
25
22

1115 2350 3582 4816 6044 7256 8457

65
62
59
56
52
49
45

9641
41

1355 2858 4368 5880 7386 8880 10352 11791

54
51
48
45
42
38
34
30

1091 2338 3586 4832 6072 7301 8515

92
88
85
80
76
72
67

9706
63

1323 2840 4363 5888 7407 8908 10384 11829

76
73
69
65
61
57
53
47

1046 2309 3564 4811 6051 7280 8499

118 114 110 105 101
96
90

9707
85

1266 2791 4326 5856 7376 8884 10372 11834

98
94
90
85
81
76
71
64

12

981 2242 3506 4757 5992 7221 8444

159 154 148 143 137 132 125

9652
118

12

1177 2698 4230 5759 7273 8773 10261 11726

131 127 121 116 110 105
98
90

15

898 2164 3437 4702 5951 7187 8416

199 193 186 180 174 168 160

9625
152

15

1075 2594 4127 5654 7170 8670 10153 11613

165 159 153 146 140 134 126 116

20

691 1976 3255 4529 5795 7044 8275

266 258 250 243 235 227 218

9499
209

20

833 2372 3915 5463 7008 8533 10026 11479

221 214 205 197 189 182 173 161

25

703 1726 2987 4260 5540 6815 8071

334 324 314 305 296 286 276

9311
267

25

678 2142 3663 5189 6726 8257 9757 11219

277 269 259 248 239 230 219 209

Flow (GPM)

Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.

Flow (GPM)

PSLGC.PM6, dg, ki

87

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
H
S
E
R
I
E
S

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0405

405 cc / rev

24.7 cu in / rev

PRESSURE (PSI)
500 1000 1500 2000 2500 3000 3500

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9 241.4

1.9

174.4 359.1 546.8 736.1 924.7

4
3
2
1
1

3.8

180.0 367.9 556.8 746.5 938.11128.31316.4

8
7
6
6
5
4
3

1593 3256 4928 6607 8303 9987 11652

8
7
6
6
5
4
3

7.6

184.8 378.6 574.4 770.2 966.01160.51353.3

17
16
15
14
13
12
11

1636 3351 5084 6817 8550 10272 11978

17
16
15
14
13
12
11

11.4

184.9 380.2 576.9 773.6 970.31165.31359.3

27
25
23
22
21
19
18

1637 3365 5106 6847 8588 10314 12031

27
25
23
22
21
19
18

15.1

185.9 383.5 582.9 781.8 979.31175.21370.4

36
34
32
30
29
27
26

1645 3394 5159 6920 8668 10402 12130

36
34
32
30
29
27
26

18.9

185.3 385.0 587.6 788.9 986.71182.41377.7

45
43
41
39
37
35
33

1640 3408 5201 6983 8733 10466 12194

45
43
41
39
37
35
33

26.5

181.4 383.7 588.7 791.2 991.11189.31386.4

64
61
59
56
54
51
49

1606 3396 5211 7003 8772 10527 12271

64
61
59
56
54
51
49

34.1

175.2 378.5 584.8 788.7 990.01188.41386.2

82
80
77
73
70
67
64

1551 3350 5176 6981 8763 10519 12269

82
80
77
73
70
67
64

45.4

161.3 365.8 573.4 778.2 979.51177.71375.2

110 107 103
99
95
91
88

12

1428 3238 5075 6888 8670 10424 12172

110 107 103
99
95
91
88

56.8

148.0 351.6 559.0 763.6 965.41164.41362.5

138 135 130 125 120 115 111

15

1310 3112 4948 6759 8545 10306 12060

138 135 130 125 120
115 111

75.7

128.3 323.3 530.1 736.4 941.81143.61341.9

185 181 175 168 162 156 151

20

1136 2862 4692 6518 8336 10122 11877

185 181 175 168 162
156 151

94.6

507.5 712.1 913.31112.61308.9

219 212 204 197 190

25

4492 6303 8084 9848 11585

219 212 204
197 190

.5

1544 3178 4840 6515 8185

4
3
2
1
1

Flow (GPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

712.1
212

(LB IN)
(RPM)

9848
197

T
H
S
E
R
I
E
S
Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

88

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0475

475 cc / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4 206.9

29.1 cu in / revPRESSURE (PSI)

500 1000 1500 2000 2500 3000
1768 3732 5733 7744 9762
3
3
2
1
1

1.9

199.7 421.6 647.7 874.91102.9

3
3
2
1
1

3.8

211.0 438.1 664.2 887.01111.51336.6

7
7
6
5
4
3

1868 3878 5879 7851 9838 11830

7
7
6
5
4
3

7.6

221.9 458.1 698.2 930.61157.01371.1

15
14
14
12
10
8

1964 4055 6180 8237 10241 12136

15
14
14
12
10
8

11.4

222.8 460.3 701.4 940.11172.61395.9

23
22
21
19
17
13

1972 4074 6208 8321 10379 12355

23
22
21
19
17
13

15.1

226.5 467.2 710.3 947.01182.11411.8

31
30
29
27
24
20

2005 4135 6287 8382 10463 12496

31
30
29
27
24
20

18.9

226.4 466.5 712.2 952.21187.91417.2

39
38
37
34
31
26

2004 4129 6304 8428 10514 12544

39
38
37
34
31
26

26.5

224.8 466.9 712.7 954.11192.51423.8

55
54
52
50
45
40

1990 4133 6308 8445 10555 12602

55
54
52
50
45
40

34.1

217.4 463.7 710.1 952.41189.51424.5

70
69
68
65
60
54

1924 4104 6285 8430 10528 12608

70
69
68
65
60
54

45.4

200.5 449.0 695.6 940.91180.21415.4

94
93
91
87
82
75

12

1775 3974 6157 8328 10446 12528

94
93
91
87
82
75

56.8

182.9 427.5 676.8 925.11164.91397.8

118 116 114 110 104
96

15

1619 3784 5990 8188 10311 12372

118 116 114 110 104
96

75.7

148.5 381.1 636.0 887.21134.11372.1

157 156 153 149 141 132

20

1314 3373 5629 7853 10038 12145

157 156 153 149 141 132

94.6

128.9 342.2 589.8 839.11087.91328.3

197 196 193 189 182 174

25

1141 3029 5220 7427 9629 11757

197 196 193 189 182 174

113.6

68.5 283.0 525.2 764.41003.01241.5

237 236 233 230 224 219

30

606 2505 4649 6766 8878 10989

237 236 233 230 224
219

.5

Flow (LPM)

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

283.0
236

(LB IN)
(RPM)

6766
230

T
H
S
E
R
I
E
S
Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

89

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0530

530 cc / rev

32.2 cu in / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9 172.4

PRESSURE (PSI)
500 1000 1500 2000 2500

1.9

235.0 480.8 732.0 985.91244.1

3
3
2
2
1

.5

2080 4256 6479 8726 11012

3
3
2
2
1

3.8

243.8 493.9 744.8 991.91242.1

7
6
6
5
4

2158 4372 6592 8779 10994

7
6
6
5
4

7.6

253.8 516.0 776.11031.11285.3

14
13
12
11
9

2246 4567 6869 9126 11376

14
13
12
11
9

11.4

253.3 517.2 781.41043.61299.3

21
20
19
17
14

2242 4578 6916 9237 11500

21
20
19
17
14

15.1

254.5 522.5 788.31050.31309.0

28
27
25
23
20

2253 4625 6977 9296 11586

28
27
25
23
20

18.9

252.5 523.0 791.11054.41313.5

35
34
32
29
26

2235 4629 7002 9333 11626

35
34
32
29
26

26.5

246.5 519.6 791.51057.71317.2

49
48
46
42
38

2182 4599 7006 9362 11659

49
48
46
42
38

34.1

236.7 512.4 786.31054.11316.2

63
62
59
55
50

2095 4535 6960 9330 11650

63
62
59
55
50

45.4

219.5 496.0 771.11041.31304.8

85
83
80
75
69

12

1943 4390 6825 9217 11549

85
83
80
75
69

56.8

198.1 474.4 750.01022.71288.9

106 104 100
95
87

15

1753 4199 6638 9052 11408

106 104 100
95
87

75.7

149.9 427.4 707.5 983.01252.5

141 139 135 129 120

20

1327 3783 6262 8701 11086

141 139 135 129 120

94.6

114.2 372.8 649.7 927.61202.0

177 175 171 165 158

25

1011 3300 5751 8210 10639

177 175 171 165 158

113.6

30.4 304.8 574.3 837.71108.8

213 211 208 203 197

30

269 2698 5083 7415 9814

213 211 208 203 197

Flow (LPM)

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

304.8
211

(LB IN)
(RPM)

9814
197

T
H
S
E
R
I
E
S
Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

90

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0625

625 cc / rev
34.5

38.0 cu in /PRESSURE
rev
(PSI)

PRESSURE (BAR)
69.0 103.4 120.7 155.2

500 1000 1500 1750 2250

1939 4593
2
1

1.9

219.1 518.9
2
1

3.8

235.8 527.1 822.8 980.7 1308.2

5
3
2
2
1

2087 4665 7283 8680 11579

5
3
2
2
1

7.6

264.1 563.9 857.5 1000.2 1294.5

11
9
8
7
5

2338 4991 7590 8853 11458

11
9
8
7
5

11.4

269.6 576.3 875.9 1023.0 1320.6

17
15
13
12
9

2386 5101 7753 9055 11689

17
15
13
12
9

15.1

277.6 587.7 889.4 1036.5 1329.7

23
21
19
17
14

2457 5202 7872 9174 11769

23
21
19
17
14

18.9

280.1 592.7 897.4 1044.2 1335.5

29
27
25
23
18

2479 5246 7943 9242 11821

29
27
25
23
18

26.5

278.4 595.7 903.3 1051.4 1339.8

41
39
36
34
28

2464 5273 7995 9306 11859

41
39
36
34
28

34.1

271.3 590.1 903.0 1054.9 1348.4

53
51
48
45
39

2401 5223 7993 9337 11935

53
51
48
45
39

45.4

254.7 575.3 891.0 1043.8 1344.5

71
69
65
62
54

12

2254 5092 7886 9239 11900

71
69
65
62
54

56.8

231.8 553.7 872.3 1026.5 1329.0

89
87
83
80
70

15

2052 4901 7721 908611763

89
87
83
80
70

75.7

180.8 507.3 828.6 985.8 1290.7

120 117 112
109
98

20

1600 4490 7334 8725 11424

120 117 112 109
98

94.6

120.1 444.4 770.3 930.4 1245.2

151 148 144
140
131

25

1063 3933 6818 8235 11021

151 148 144 140 131

113.6

40.6 367.2 686.2 840.9 1150.0

182 180 176
172
165

30

359 3250 6074 7443 10179

182 180 176 172 165

.5

Flow (LPM)

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

367.2
180

(LB IN)
(RPM)

7443
172

T
H
S
E
R
I
E
S
Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

91

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0785

785 cc / rev

48.0 cu in / rev

PRESSURE (BAR)
34.5 69.0 103.4 137.9

PRESSURE (PSI)
500 1000 1500 2000

1.9

328.8 695.2 1085.4 1463.1

2
2
1
1

.5

2910 6153 9607 12950

2
2
1
1

3.8

340.2 711.3 1092.5 1459.6

4
4
3
3

3011 6296 9670 12919

4
4
3
3

7.6

363.5 738.4 1122.5 1475.5

9
8
7
6

3217 6536 9935 13060

9
8
7
6

11.4

363.8 747.1 1127.2 1477.7

14
13
11
9

3220 6613 9977 13079

14
13
11
9

15.1

368.9 754.6 1132.2 1477.6

19
17
15
13

3265 6679 10021 13078

19
17
15
13

18.9

368.7 757.3 1135.1 1480.4

23
22
19
16

3263 6703 10047 13103

23
22
19
16

26.5

363.6 759.5 1137.5 1475.7

33
31
28
24

3218 6722 10068 13062

33
31
28
24

34.1

351.0 752.9 1142.0 1489.6

43
41
36
31

3107 6664 10108 13185

43
41
36
31

45.4

326.7 733.1 1125.2 1478.0

57
55
49
42

12

2892 6489 9959 13082

57
55
49
42

56.8

298.6 704.8 1099.6 1461.7

71
69
62
54

15

2643 6238 9733 12938

71
69
62
54

75.7

230.9 640.9 1043.8 1427.6

95
92
85
75

20

2044 5673 9239 12636

95
92
85
75

94.6

261.3 562.2 968.4 1364.0

119 117
110 101

25

2313 4976 8571 12073

119 117 110 101

113.6

56.0 463.7 856.6 1245.5

143 141
137 130

30

496 4104 7582 11024

143 141 137 130

Flow (LPM)

Flow (GPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

856.6
137

(LB IN) 11024

(RPM)
130

T
H
S
E
R
I
E
S
Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

92

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Performance Data
Code 0960

58.5 cu in / rev

960 ccPRESSURE
/ rev
(BAR)
34.5

PRESSURE (PSI)
500 1000 1500

69.0 103.4

1.9

417.1 871.3 1327.5

2
1
1

.5

3692 7712 11750

2
1
1

3.8

428.0 887.8 1343.9

3
3
3

3788 7858 11895

3
3
3

7.6

440.6 908.9 1362.3

7
7
6

3900 8045 12058

7
7
6

11.4

441.2 912.7 1371.0

11
11
10

3905 8078 12135

11
11
10

15.1

445.0 921.4 1379.5

15
14
13

3939 8155 12210

15
14
13

18.9

443.2 923.4 1382.6

19
18
17

3923 8173 12238

19
18
17

26.5

436.1 921.9 1385.4

27
26
24

3860 8160 12262

27
26
24

34.1

421.8 912.2 1381.1

35
34
31

3733 8074 12224

35
34
31

45.4

392.6 886.7 1362.8

47
45
42

12

3475 7848 12062

47
45
42

56.8

355.8 852.4 1335.8

58
57
53

15

3149 7545 11823

58
57
53

75.7

275.3 773.1 1268.4

78
76
72

20

2437 6843 11227

78
76
72

94.6

335.4 676.8 1170.5

98
96
92

25

2969 5990 10360

98
96
92

30

603 4919 9170

118 117 113

113.6

68.1
118

555.7 1036.0
117 113

Flow (GPM)

Flow (LPM)
TORQUE
SPEED

(nm)
(RPM)

TORQUE
SPEED

555.7
117

(LB IN)
(RPM)

9170
113

T
H
S
E
R
I
E
S
Performance data
is typical. Actual
data may vary
slightly from one
production motor
to another.
PSLGC.PM6, dg, ki

93

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Dimensional Data

Lengths & Weights

Inch equivalents for metric dimensions are shown in (**)

"L2"
"L1"

Wheel Mount

Magneto Mount

Standard Rotation:
(As viewed from shaft end)
Front Ports - Pressurize "A" to turn Counterclockwise, "B" to turn Clockwise.
Rear Ports - Pressurize "A" to turn Clockwise, "B" to turn Counterclockwise.

Length "L" and Weight

Displacement, Code

0140

0170

0195

0240

0280

0335

0405

0475

0530

0625

0785

0960

Magneto Mount

T
H

Length "L1"

mm
(inches)
kg

Weight

(lb)

S
E
R
I
E
S

216
219
222
227
232
238
245
254
260
270
289
308
(8.50) (8.62) (8.75) (8.94) (9.12) (9.37) (9.66) (10.00) (10.25) (10.62) (11.37) (12.12)
14.7
(32.3)

14.9
15.2 15.5 15.9
(32.8) (33.4) (34.2) (35.1)

16.3
(35.9)

16.9
17.6
(37.3) (38.7)

18.3 19.0
20.6
(40.4) (41.9) (45.4)

22.3
(49.1)

Wheel Mount
Length "L1"

mm
(inches)

Weight

kg
(lb)

173
177
180
184
189
196
203
212
218
227
246
265
(6.82) (6.95) (7.07) (7.26) (7.45) (7.70) (7.99) (8.32) (8.57) (8.95) (9.70) (10.45)
16.9
(37.3)

17.2
17.4 17.8 18.2
(37.8) (38.4) (39.2) (40.1)

18.6
(40.9)

19.2
19.8
(42.3) (43.7)

20.6 21.3
22.9
(45.4) (46.9) (50.4)

24.5
(54.1)

PSLGC.PM6, dg, ki

94

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Dimensional Data

Mounting
Inch equivalents for metric dimensions are shown in (**)
22 30'

62.81 (2.473)
15.7 (.62)

2.8 (.11)

82.52 (3.249)

4 Bolt Magneto

133.4 (5.25)

4 x 13.49 (17/32) thru holes

on a 106.38 (4.188) BC
45

45.21 (1.780)

63.83 (2.513)

39.88 (1.570)

45
35.05 (1.380)

3.56 (.140) Min

Wheel
126.95
(4.998)

82.52
71.73
(2.824) (3.249)

25.4 (1.00)
25.4 (1.00)

Shafts

4X 13.5 (17/32) equally spaced

on a 147.62 (5.182) Bolt Circle

T
H

77.5
(3.05)

9.50 (.374)
2.8 (.11)

47.88 (1.885)

105.4 (4.15)

62.99 (2.480)
9.50 (.374)

50.29 (1.980)
41.83 (1.647)

41.7 (1.64)
Min Full Spline
37.757 (1.4865

38.10 (1.500)
7/8-14 UNF thd
(x 23.6 [.93] Deep)

1 1/2" Keyed

1.25-18 UNEF thd

38.1 Taper per meter
(1.500 Taper per foot)

1 1/2" Taper

5/8-18 UNF thd

(x 19.1 [.75] Deep)

17T-12/24 Spline

PSLGC.PM6, dg, ki

95

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

S
E
R
I
E
S

Catalog 1510-20

Dimensional Data

Low Speed High Torque Motors

TH Series

Porting
Inch equivalents for metric dimensions are shown in (**)

64.3
(2.53)

SAE O-Ring
25.40 (1.000)
7/8-14 SAE O-Ring
or
1/2" BSPF

Rear Ports
65.53 (2.580)
7/8-14 SAE O-Ring

22.86 (.900)

A
129.5
(5.10)

7/8-14 SAE O-Ring

B
45.72 (1.800)

T
H
14.27 (.562)
65.53 (2.580)
28.58 (1.125)
22.86 (.900)

A
63.50 (2.500)

Manifold

S
E
R
I
E
S

45.72 (1.800)
31.75 (1.250)
4 x 5/16-18 UNC thd
x .50 Min Deep

Consult Factory for

ISO 6149 Porting
PSLGC.PM6, dg, ki

96

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

TH Series

Catalog 1510-20

Ordering Information

TH

XXXX

Series

Displacement

Mounting

Porting

Code Displacement
0140
0170
0195
0240
0280
0335
0405
0475
0530
0625
0785
0960

08.6
10.3
11.9
14.5
17.1
20.6
24.7
29.1
32.3
38.0
48.0
58.5

Code
M
U

cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu
cu

in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev
in/rev

Mounting
Magneto
Wheel; Standard

Code

Shaft

31
32
36

1 1/2" Tapered
1 1/2" Keyed
17 Tooth Spline

Code
A
B
E
J
M*
S
T**

XX

Porting

Code

7/8"-14 SAE O-Ring; Rear Axial

7/8"-14 SAE O-Ring; Rear Radial
Manifold; Rear Radial
ISO 6149 M22x1.5
Manifold
7/8"-14 SAE O-Ring
1/2" BSPF

Not available on U mounting

**

Available on M mounting only

Code
AAAA
AAAB
AAAC
AAFC
AAAF***
AABP***
AAAG
AAAH
AAHD
AAAJ
AAFG
AAAT*
AAFX*
AAAU*
AAGF*
AABJ****
AABK****
AABL****
AABM****
BBBA*
BBBM*
BBBG*
BBBJ*
BBBB*
BBBN*
BBBK*
BBBC*
BBBF*
BBBD*
BBBW*
FFAA
FFAB
FFAH
FFAJ
*
**
***
****

PSLGC.PM6, dg, ki

97

Hydraulics

Shaft

0
1

XXXX

Rotation

Options

Rotation
Standard
Reverse Timed Manifold

Options
Black Paint
No Paint
Double Paint
White Epoxy Paint
Castle Nut, Black Paint
Castle Nut, No Paint
Viton Seals, Black Paint
Viton Seals, No Paint
Viton Seals, White Epoxy Paint
Vespel Commutator Seal, Black Paint
Vespel Commutator Seal, No Paint
Bidirectional Shuttle (11:00**), Black Paint
Bidirectional Shuttle (11:00**), No Paint
Bidirectional Shuttle (11:00**), Castle Nut, Black Paint
Bidirectional Shuttle (11:00**), Castle Nut, No Paint
Free Running Rotorset, Black Paint
Free Running Rotorset, No Paint
Free Running Rotorset, No Commutator Seal, Black Paint
Free Running Rotorset, No Commutator Seal, No Paint
1000 PSI Internal Bidirectional Relief, Black Paint
1000 PSI Internal Bidirectional Relief, No Paint
1500 PSI Internal Bidirectional Relief, Black Paint
1500 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Black Paint
2000 PSI Internal Bidirectional Relief, No Paint
2000 PSI Internal Bidirectional Relief, Castle Nut, Black Paint
3000 PSI Internal Bidirectional Relief, Black Paint
3000 PSI Internal Bidirectional Relief, No Paint
4000 PSI Internal Bidirectional Relief, Black Paint
4000 PSI Internal Bidirectional Relief, No Paint
Internal Speed Sensor, Black Paint
Internal Speed Sensor, No Paint
Internal Speed Sensor, Castle Nut, No Paint
Internal Speed Sensor, Castle Nut, Black Paint

Not available with A, B or E porting

Shuttle port position as viewed from shaft end of motor
Available only with shaft code 08 & 19
Not available on 0625, 0785 or 0960 displacement codes

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

T
H
S
E
R
I
E
S

Catalog 1510-20

Cross-Over Relief Valve

Low Speed High Torque Motors

Accessories

Application
The Cross-Over Relief Valve is designed to provide
overload and shock protection for our LSHT motors
built with the manifold port option. Close coupling
the valve to the motor provides ideal protection and
eliminates plumbing.

Specifications

Rated flow 75.7 lpm (20 gpm)

Max. Operating Pressure 241.4 bar (3500 psi)

Reseat Pressure 90% of set pressure

Operating Temperature Range: -40C to 121C

(-40F to 250F)

Cartridge Material All parts steel. All

operating parts hardened steel.

Body Material Steel

Filtration Maintain SAE Class 4

Mounting TA, TB & TD Series only. See

dimensions for mounting pattern.

Mounting Bolts Torque 33.9 2.7 nm

(25 2 ft lb)

Performance Curve
Flow vs. Pressure
275.9
(4000)

Features
Fast acting differential area reliefs

Low leakage

Serviceable cartridge design

Hardened operating parts for long life

Operation
The valve relieves oil from one side of the motor to
the other reducing shock and preventing overload.
It also reduces the possibility of cavitation.

Inlet Pressure - Bar (PSI)

241.4
(3500)
206.9
(3000)

Hydraulic Oil 100 SUS

172.4
(2500)
137.9
(2000)
103.4
(1500)
69.0
(1000)

T
34.5
(500)

0
(0)
Flow - LPM (GPM)

18.9
(5)

37.9
(10)

56.8
(15)

PSLGC.PM6, dg, ki

98

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

75.7
(20)

Low Speed High Torque Motors

Accessories

Catalog 1510-20

Cross-Over Relief Valve

Dimensions
Inch equivalents for metric dimensions are shown in (**)

47.5
(1.87)

85.3 (3.36)
Max

69.9
(2.75)

50.8
(2.00)

23.9
(.94)

8.9
(.350)

55.6
(2.19)

7.9
(.31)

28.6 (1.125)
33.3 (1.31)

45.7
(1.800)
63.5
(2.500)

79.2
(3.12)
1/4" Hollow Hex
.343 Dia Thru
.500 Dia Cbore x .37 DP
Mounting Hole

Top View

14.3 (.562)

12.57
(.495)
Dia.

2 x 9/16-18 SAE
Str thd Port

Rear View

Bottom View

34.5 (1.36)

50.8
(2.00)
Ref

15.5 (.61)

Side View

Valve Mounted on Motor

79.2
(3.12)

50.8
(2.00)

Rear View

Top View

Ordering Information
To order a cross-over relief valve mounted on a specific motor see the ordering information for that motor.
To order a cross-over relief valve as a field conversion or as a spare part use P/N 1894-1 (manifold mount required on motor).
Mounting bolts are available as P/N 021450 (4 required).
PSLGC.PM6, dg, ki

99

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Catalog 1510-20

Cross Port Relief / Hot Oil Shuttle

Low Speed High Torque Motors

Accessories

Cross Port Relief

Fixed setting crossover relief valves may be ordered to
protect the motor from hydraulic overpressurization. These
valves are built into the endcover and relieve pressure from
the high pressure to the low pressure port. This accessory
adds 27.7 mm (1.09 in.) to the "L" dimension.

25 43

Torque to
2 x 61-75 Nm (45-55 ft lb)

26.97 (1.062)

Hot Oil Shuttle

A Hot Oil Shuttle is used to continuously remove a portion of the fluid in a closed loop transmission or other
closed loop system. At 125 PSI pressure differential between the motor return port and the shuttle outlet, 1.5
GPM* will exit the circuit to cool, filter and return to the reservoir. The constant loop replenishment helps to keep
heat and contamination from building up in the circuit.
*with 200 SSU fluid

18.0 (.71)
Shuttle
Port CL

B
25 43'
9/16-18 Straight thd
O-Ring Port
(Shuttle Port)

PSLGC.PM6, dg, ki

100

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Accessories

Catalog 1510-20

Speed Sensor

An Economical Sensor for Speed

Readout
This rugged, weather resistant speed sensor is a
Hall effect device. When externally powered, 30
square wave digital pulses per output shaft revolution are produced. By signal multiplication, 60
pulses per revolution can be obtained.
The installation of this economical sensor does not
affect the torque or side load capability of the
TorqlinkTM motor into which it is installed.

Features

2
N/C

1
+

3
-

4
Output

Operating Voltage Range .......... 4.5 to 24 VDC

Operating Temperature ............. -40 C to 93 C
(-40 F to 200 F)
Operating Frequency Range ..... 0 to 100 KHZ
Maximum Sink Current ............. 20 mA
Connection ................................ DC Din Standard
4 Pin Micro-Mini
Pin Diameter ............................. 12mm
Sensor Output ........................... 30 Pulses per
revolution which can be
doubled electronically.
Pull-up Resistor Value Formula
(for 1/4 Watt, 5% Tolerance)
V Supply (4.5-24 VDC)
Desired Sink Current (0-20 mA 20%)

= Resistor Value
(K - Ohms)

+ 4.5 to 24 VDC

Pin # 4

Output

Pin # 3

- Negative

Pin # 2

No Connection

SENSOR

On State Current: 5 mA
Higher wattage resistor will be needed for higher
sink current.

+V Off State

Pin # 1

Min Off State = .95%+V

On State Max On State = .400VDC

0V

Cable not included

PSLGC.PM6, dg, ki

101

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Installation/Operation Information
Fluid

Installation Recommendations

To insure maximum motor performance and life, use

premium grade hydraulic oils. Fluids with a minimum
of .125% zinc anti-wear additives should be used.
API 10W40 SF or CD motor oils are recommended.
Seals in Torqlink Series motors are Buna-N,
compatible with most mineral based and engine oils.
If using synthetic fluids consult the factory for
alternative seal materials.
Minimum fluid viscosity is 50 SSU
Fluid operating temperature is -28 C to 93 C
(-20F to 200 F)
Filtration level is 20-50 micron nominal

To avoid contamination do not remove plastic port

plugs until fittings are to be installed.
Use SAE Grade 8 bolts and nuts. Torque on nonplated, lightly oiled mounting hardware should be
105 lb ft.
Motor mounting flange must make full contact with
equipment mount; do not use the mounting bolts
to force the motor pilot into the pilot hole to align
the motor.
Pulleys, sprockets, wheels, or couplings should
be properly aligned on the shaft to avoid excessive
radial or thrust loads.
To avoid damaging the thrust system, do not
hammer on the motor or shaft to install or remove
couplings, pulleys, sprockets, etc.

Pressure
Operating the motor in its intermittent pressure
range will shorten the life of the motor and should
generally be restricted to 10% or less per minute.
The reduced life resulting from continuous operation
in the intermittent range may be acceptable in some
applications. Consult the factory for details.

Castle Nut
All motors ordered with Tapered shafts are equipped
with patch locking nuts. If desired, a castle nut may
be specified.

Shaft Loading
Use of one inch and 25mm shafts are not recommended when torque loads exceed 3500 lb. in. For
the Corrosion Resistant Shaft "N" option limit torque
to 1300 lb. in. For 7/8 inch splined shafts limit
torque to 1250 lb. in. Maximum thrust load on the
shaft should not exceed 1000 pounds inward of
outward.

Paint
Unless specified otherwise, motors are shipped
unpainted and coated with a rust inhibitor. Paint
options are:
Single coat of black paint
Double coat of black paint for increased corrosion
resistance
Multi-layered coating of white FDA approved
epoxy for superior corrosion resistance

Performance Data
Performance data shown in this catalog is the result
of testing performed using 10W40 oil at 54 C
(130 F), 200 SUS. Actual performance will vary
with fluid conditions. Lower viscosity will produce
lower performance.

Vespel Commutator Seal

Under conditions of high temperature or low lubricity,
it is possible for the standard commutator seal to
extrude. A Vespel seal should be specified.

Inlet Conditions
Positive pressure must be available at the motor
inlet while it is rotating. If an overrunning load
causes the motor to rotate faster than the pump can
fill it, cavitation will occur. Consult the factory for
inlet pressure requirements and speed limitations.

Reverse Timed Manifold

All Torqlink Series motors are bi-directional. The
port that must be pressurized to obtain a desired
direction of rotation is shown on the catalog page for
that motor. To change that port specify a Reverse
Timed Manifold.

Other Operating Conditions

Consult factory before operating at conditions
exceeding any ratings or recommendations in this
catalog.

PSLGC.PM6, dg, ki

102

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Engineering Data
Hydraulic Formulas

Side Load
Side loads are imposed upon the shaft of a motor
by:

QP

HP in = 1714

Driving the load through a pulley or gear

Supporting the weight of a vehicle or other load on
the shaft
Or both

NT

HP out = 63025
T=

D Pem
2
DN

Q = 231 e
v
Where
HP
Q
P
P
T
D

=
=
=
=
=
=

N =
em =
ev =

If the load above requires torque T pound-inches

and is driven with a pulley on the motor shaft a with
a radius of R inches, the side load imposed on the
motor shaft is T/R pounds. If the motor shaft is
connected to a sprocket for a chain drive, R is one
half the pitch diameter of the sprocket. If an external load with a weight of W pounds is also being
supported by the motor shaft above, the total side
load on the shaft is:

Horsepower
Flow, GPM
Pressure, PSI
Pressure differential across the motor
Torque, lb in
Motor displacement, cubic inches per
revolution
Shaft Speed, RPM
Mechanical efficiency
Volumetric efficiency

To Convert
Into

Into
To Convert

bars
BTU/min
BTU/min
centigrade
centimeters
cu. cms.
cu. cms.
cu. inches
cu. inches
feet
gallons
gallons
horsepower
inches
kilograms
pounds
pound-inches
pound-inches
radians
square inches

pounds/sq.in.
horsepower
kilowatts
fahrenheit
inches
cu. inches
liters
cu.cms.
liters
meters
cu. inches
liters
kilowatts
millimeters
pounds
newtons
newton-meters
daNM
degrees
sq. cms.

Multiply By
Divide By
14.5
.02356
.01757
(Cx9/5)+32
.3937
.06102
.001
16.39
.01639
.3048
231
3.785
.7457
25.4
2.205
4.448
.113
.0113
57.3
6.452

(SL)2 = W2 + (T/R)2
Side Load(lb) =

W 2 + (T/R)2

Warning
This Catalog is not a Controlled Document. All
Dimensions listed herein are for reference only.
Consult a Sales engineer for detailed information.

PSLGC.PM6, dg, ki

103

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Engineering Data
Vehicle Propulsion Systems
Hydraulic motors are often used to drive off-highway vehicles, either directly or through gear reducers. The
power required to propel the vehicle, called "Tractive Effort," is supplied by the hydraulic motor(s). It is normally
expressed in pounds and is the sum of the forces below:

TE = (RR+GR+F+DP) x 1.1

Where:

RR
GR
F

=
=
=

Rolling Resistance
Grade Resistance
Acceleration Force

DP

Drawbar Pull

Definitions

Tractive Effort (TE)

Tractive effort is the total linear force that a vehicle can
exert on the ground. Sometimes called "rim pull," it is
the axle torque divided by the distance from the axle to
the surface it is traversing.

Rolling Resistance (RR)

Rolling resistance is the force in pounds required
to propel a vehicle at constant speed over level
terrain. It varies with the weight of the vehicle
and the type of surface it is traversing. Soft sand,
for example, offers more resistance to movement
than concrete
RR = GVW x R
RR

where:

= Rolling Resistance (lbs.)

Surface
Type

Surface
Condition

R
Value

Concrete
Concrete

Excellent
Good

0.010 lb.
0.015 lb.

Concrete
Asphalt

Poor
Good

0.020 lb.
0.012 lb.

Asphalt

Fair

0.017 lb.

Asphalt
Macadam

Poor
Good

0.022 lb.
0.015 lb.

Macadam
Macadam

Fair
Poor

0.022 lb.
0.037 lb.

Cobbles

Ordinary

0.055 lb.

Cobbles
Snow

Poor
2 In.

0.085 lb.
0.025 lb.

Snow
Dirt

4 In.
Smooth

0.037 lb.
0.025 lb.

Dirt

Sandy

0.037 lb.

Mud
Sand

Level/Soft

0.037 to 0.150 lb.

0.060 to 0.150 lb.

Sand

Dune

0.150 to 0.300 lb.

GVW = Gross Vehicle Weight (lbs.)

R

= Rolling Resistance Factor dependent

upon type and condition of surface.
Typical "R" values are shown in the
accompanying table.

PSLGC.PM6, dg, ki

104

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Engineering Data
Grade Resistance (GR)

Grade resistance is the additional force required

to move a vehicle up an incline. The grade of a
slope is normally expressed as a percentage, and
represents the number of feet of rise in 100 feet
of length. A slope that rises 10 feet in 100 feet
has a grade of 10%. The gradeability of a vehicle
is defined as the maximum grade the vehicle can
climb.

= Change in Velocity (ft. per Second)

(Final Velocity - Initial Velocity)

GVW = Gross Vehicle Weight (lbs.)

T

= Time for Velocity Change (Seconds)

Note - To obtain velocity in feet per second

when MPH is known, Multiply MPH
by 1.467.

Drawbar Pull (DP)

GR = 0.01 x GVW x G
GR

where:
Drawbar Pull is the force a vehicle can exert on a
load in addition to the force required to propel
itself.

Grade Resistance (lbs.)

GVW =

Gross Vehicle Weight (lbs.)

Grade (%)

Actual force to tow or push a load can be calculated based upon Rolling Resistance, Accelerating Force and Grade Resistance of towed or
pushed load.

The following table gives the approximate relationship between grade in percent and slope in
degrees.

Grade (Percent)

Motor Torque
The total Tractive effort required to propel a
vehicle is the sum of the forces due to Rolling
Resistance, Grade Resistance, Acceleration and
Drawbar Pull plus 10% for friction and other
variables:

Slope (Degrees)

1%

0 35'

2%

5%

2 51'

9'

6%

3 26'

8%

4 35'

10%

5 43'

12%

6 54'

15%

8 31'

20%

11 19'

TE = (RR + GR + F + DP) x 1.1

When Tractive Effort has been calculated,
hydraulic motor torque can be estimated by:

T =

GxN

where:

25%

14

32%

18

3'

60%

31

TE = Tractive Effort

The force required to accelerate a vehicle from an

initial speed V1 (in feet/second) to speed V2 in T
seconds is the accelerating force in pounds. If
the acceleration is from rest, V1 is zero.
V x GVW
T x 32.16

= Hydraulic Motor Torque (lbs. in.)

= Rolling Radius of Driven Tires (inches)

= Gear Reduction Ratio Between Hydraulic Motors and Driven Wheels ( if

none, use a value of 1)

= Number of Driving Motors

Acceleration Force (F)

F=

TE x r

where

PSLGC.PM6, dg, ki

105

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Engineering Data
Hydraulic Motor Speed

Slip Torque
Slip torque is the torque at the motor shaft
that will cause the wheels or tracks to break
traction and skid. It is affected by the weight
of the vehicle and the coefficient of friction
between the wheels or tracks and the surface.

ST =

VW x u x r
GxN

168 x V x G

S =

Required Hydraulic Motor Speed

(RPM)

Desired Vehicle Velocity (MPH)

Gear Reduction Ratio Between

Hydraulic Motors and Driven
Wheels ( if none, use a value of 1)

Rolling Radius of driven Tires

(inches)

where:

ST =

Hydraulic Motor Slip Torque (lb in)

VW =

Maximum Weight on Driven Wheel

(lb) Including: Allowable Vehicle
Overload Dynamic Weight Shift.

Coefficient of Friction Between Tire

and Ground. (A value of 0.6 is used
for "normal" tires and an average
road surface)

Rolling Radius of Driven Tires

(inches)

Gear Reduction Ratio Between

Hydraulic Motors and Driven Wheel.

Number of Driving Motors

where:

The chart below will estimate the wheel RPM -vsvehicle velocity for various rolling radii.

MPH -vs- RPM

for different Rolling Radii
700

6"R

RPM

600
8"R

500

10"R

Rolling Radius

400
12"R

The rolling radius should be based on actual

application factors such as Plyrating, Rated Load
and inflation pressure can result in different
values.

300

14"R
16"R
18"R
20"R

200
100

10

15

20

25

MPH

PSLGC.PM6, dg, ki

106

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

PSLGC.PM6, dg, ki

107

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Low Speed High Torque Motors

Catalog 1510-20

Offer of Sale
The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This offer and its
acceptance by any customer (Buyer) shall be governed by all of the following Terms and Conditions. Buyers order for any such item, when communicated to
Parker Hannifin Corporation, its subsidiary or an authorized distributor (Seller) verbally or in writing, shall constitute acceptance of this offer.
1. Terms and Conditions of Sale: All descriptions, quotations,
proposals, offers, acknowledgments, acceptances and sales of Sellers
products are subject to and shall be governed exclusively by the terms
and conditions stated herein. Buyers acceptance of any offer to sell is
limited to these terms and conditions. Any terms or conditions in
addition to, or inconsistent with those stated herein, proposed by Buyer
in any acceptance of an offer by Seller, are hereby objected to. No
such additional, different or inconsistent terms and conditions shall
become part of the contract between Buyer and Seller unless expressly
accepted in writing by Seller. Sellers acceptance of any offer to
purchase by Buyer is expressly conditional upon Buyers assent to all
the terms and conditions stated herein, including any terms in addition
to, or inconsistent with those contained in Buyers offer. Acceptance of
Sellers products shall in all events constitute such assent.
2. Payment: Payment shall be made by Buyer net 30 days from the
date of delivery of the items purchased hereunder. Amounts not timely
paid shall bear interest at the maximum rate permitted by law for each
month or portion thereof that the Buyer is late in making payment. Any
claims by Buyer for omissions or shortages in a shipment shall be
waived unless Seller receives notice thereof within 30 days after
Buyers receipt of the shipment.
3. Delivery: Unless otherwise provided on the face hereof, delivery
shall be made F.O.B. Sellers plant. Regardless of the method of
delivery, however, risk of loss shall pass to Buyer upon Sellers delivery
to a carrier. Any delivery dates shown are approximate only and Seller
shall have no liability for any delays in delivery.
4. Warranty: Seller warrants that the items sold hereunder shall be
free from defects in material or workmanship for a period of 5 years
from date of shipment from Parker Hannifin Corporation. THIS
WARRANTY COMPROMISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER.
SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR
REPRESENTATION OF ANY KIND WHATSOEVER. ALL OTHER
WARRANTIES, INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS,
IMPLIED, OR ARISING BY OPERATION OF LAW. TRADE USAGE,
OR COURSE OF DEALING ARE HEREBY DISCLAIMED. NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY
OR PARTIALLY, TO BUYERS DESIGNS OR SPECIFICATIONS.
5. Limitation of Remedy: SELLERS LIABILITY ARISING FROM
OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS
CONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR
REPLACEMENT OF THE ITEMS SOLD OR REFUND OF THE
PURCHASE PRICE PAID BY BUYER, AT SELLERS SOLE
OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY
KIND OR NATURE WHATSOEVER. INCLUDING BUT NOT
LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY
CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF
CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT,
INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO
WARN OR STRICT LIABILITY.
6. Changes, Reschedules and Cancellations: Buyer may request to
modify the designs or specification for items sold hereunder as well as
the quantities and delivery dates thereof, or may request to cancel all or
part of this order, however, no such requested modification or
cancellation shall become part of the contract between buyer and Seller
unless accepted by Seller in written amendment to this Agreement.
Acceptance of any such requested modification or cancellation shall be
at Sellers discretion, and shall be upon such terms and conditions as
Seller may require.
7. Special Tooling: A tooling charge may be imposed for any special
tooling, including without limitation, dies, fixtures, molds and patterns,
acquired to manufacture items sold pursuant to this contract. Such
special tooling shall be and remain Sellers property notwithstanding
payment of any charges by Buyer, in no event will Buyer acquire any
interest in apparatus belonging to Seller which is utilized in the
manufacture of the items sold hereunder, even if such apparatus has
been specially converted or adapted for such manufacture and
notwithstanding any charges paid by Buyer. Unless otherwise agreed,

Seller shall have the right to alter, discard or otherwise dispose of any
special tooling or other property in its sole discretion at any time.
8. Buyers Property: Any designs, tools, patterns, materials, drawings.
Confidential information or equipment furnished by buyer, or any other
items which become Buyers property, may be considered obsolete and
may be destroyed by Seller after two (2) consecutive years have
elapsed without Buyer placing an order for the items which are
manufactured using such property. Seller shall not be responsible for
any loss or damage to such property while it is in Sellers possession or
control.
9. Taxes: Unless otherwise indicated on the face hereof, all prices and
charges are exclusive of excise, sales, use, property, occupational or
like taxes which may be imposed by any taxing authority upon the
manufacture, sale or delivery of the items sold hereunder. If any such
taxes must be paid by Seller or if Seller is liable for the collection of
such tax, the amount hereof shall be in addition to amounts for the
items sold. Buyer agrees to pay all such taxes or to reimburse Seller
therefore upon receipt of its invoice. If Buyer claims exemption from
any sales, use or other tax imposed by any taxing authority, Buyer shall
save Seller harmless from and against any such tax together with any
interest or penalties thereon which may be assessed if the items are
held to be taxable.
10. Indemnity For Infringement of Intellectual Property Rights:
Seller shall have no liability for infringement of any patents, trademarks,
copyrights, trade dress, trade secrets or similar rights except as
provided in this Part 10. Seller will defend and indemnify Buyer against
allegations of infringement of U.S. Patents, U.S. Trademarks, copyrights, trade dress and trade secrets (hereinafter Intellectual Property
Rights). Seller will defend at its expense and will pay the cost of any
settlement or damages awarded in an action brought against Buyer
based on an allegation that an item sold pursuant to this contract
infringes the Intellectual Property Rights of a third party. Sellers
obligation to defend and indemnify Buyer is contingent on Buyer
notifying Seller within ten (10) days after Buyer becomes aware of such
allegations of infringement, and Seller having sole control over the
defense of any allegations or actions including all negotiations for
settlement or compromise. If an item sold hereunder is subject to a
claim that it infringes the Intellectual Property Rights of a third party,
Seller may, at its sole expense and option, procure for Buyer the right to
continue using said item, replace or modify said item so as to make it
noninfringing, or offer to accept return of said item and return the
purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of
infringement based on information provided by Buyer, or directed to
items delivered hereunder for which the designs are specified in whole
or part by Buyer, or infringements resulting from the modification,
combination or use in a system of any item sold hereunder. The
foregoing provisions of this Part 10 shall constitute Sellers sole and
exclusive liability and buyers sole and exclusive remedy for infringement of Intellectual Property Rights. If a claim is based on information
provided by Buyer or if the design for an item delivered hereunder is
specified in whole or in part by Buyer, buyer shall defend and indemnify
Seller for all costs, expenses of or judgments resulting from any claim
that such item infringes any patent, trademark, copyright, trade dress,
trade secret or any similar right.
11. Force Majeure: Seller does not assume the risk of and shall not be
liable for delay or failure to perform any of Sellers obligations by reason
of circumstances beyond the reasonable control of Seller (hereinafter
Events of Force Majeure). Events of Force Majeure shall include
without limitation, accidents, acts of god, strikes or labor disputes, acts,
laws, rules or regulations of any government or government agency,
fires, floods, delays or failures in delivery of carries or suppliers,
shortages of materials and any other cause beyond Sellers control.
12. Entire Agreement/Governing Law: The terms and conditions set
forth herein, together with any amendments, modifications and any
different terms or conditions expressly accepted by Seller in writing,
shall constitute the entire Agreement concerning the items sold, and
there are no oral or other representation or agreements which pertain
thereto. This Agreement shall be governed in all respects by the law of
the State of Ohio. No actions arising out of the sale of the items sold
hereunder or this Agreement may be brought by either party more than
two (2) years after the cause of action accrues.

PSLGC.PM6, dg, ki

108

Hydraulics

Parker Hannifin Corporation

Hydraulic Pump/Motor Division
Greeneville, TN 37744 USA

Parker Hannifin Corporation

6035 Parkland Blvd.
Cleveland, Ohio 44124-4141
Telephone: (216) 896-3000
Fax: (216) 896-4000
Web site: www.parker.com

About Parker Hannifin Corporation

Parker Hannifin is a leading global motion-control company dedicated to delivering premier
customer service. A Fortune 500 corporation
listed on the New York Stock Exchange (PH), our
components and systems comprise over 1,400
product lines that control motion in some 1,000
industrial and aerospace markets. Parker is the
only manufacturer to offer its customers a choice
of hydraulic, pneumatic, and electromechanical
motion-control solutions. Our Company has the
largest distribution network in its field, with over
7,500 distributors serving more than 350,000
customers worldwide.

Parker Hannifin Corporation

Parkers Charter
To be a leading worldwide manufacturer of components and systems for the builders and users of
durable goods. More specifically, we will design,
market and manufacture products controlling motion, flow and pressure. We will achieve profitable
growth through premier customer service.
Product Information
North American customers seeking product information, the location of a nearby distributor, or
repair services will receive prompt attention by
calling the Parker Product Information Center at
our toll-free number: 1-800-C-PARKER (1-800272-7537). In the UK, a similar service is
available by calling 0500-103-203.

The Aerospace Groupis

a leader in the development, design, manufacture
and servicing of control systems and components for
aerospace and related hightechnology markets, while
achieving growth through
premier customer service.

The Climate & Industrial

Controls Group designs,
manufactures and markets
system-control and fluidhandling components and
systems to refrigeration,
air-conditioning and industrial customers worldwide.

The Fluid Connectors Group

designs, manufactures and
markets rigid and flexible
connectors, and associated
products used in pneumatic
and fluid systems.

The Seal Groupdesigns,

manufactures and
distributes industrial and
commercial sealing devices
and related products by
providing superior quality
and total customer
satisfaction.

The Hydraulics Group

designs, produces and
markets a full spectrum of
hydraulic components and
systems to builders and
users of industrial and
mobile machinery and
equipment.

The Filtration Group

designs, manufactures and
markets quality filtration
and clarification products,
providing customers with
the best value, quality,
technical support, and
global availability.

The Automation Group

is a leading supplier of
pneumatic and electromechanical components
and systems to
automation customers
worldwide.

The Instrumentation Group

is a global leader in the design, manufacture and distribution of high-quality
critical flow components for
worldwide process
instrumentation, ultrahigh-purity, medical and
analytical applications.

Hydraulics

Parker Hannifin Corporation

Hydraulics
2745 Snapps Ferry Road
Greeneville, TN 37745 USA
Tel:
(423) 639-8151
Fax:
(423) 787-2418
Web site: http://www.parker.com

HPMD 5000 DG# 69050 11/97