Siliconized
Acrylic Sealant
constructive solutions
General purpose acrylic joint sealant
Uses
Precautions
As an Internally or externally applied joint sealant around
window and door frames. It is also suitable for use as a joint
sealant in brick-work, block-work and sealing lightweight
cladding panels.
General
Siliconized Acrylic Sealant has excellent adhesion to most
substrates used in construction, particularly concrete,
mortar, block-work, wood and anodized bronze. It also
bonds very well to some painted surfaces, but it is advisable
to carry out a site trial first to assess the suitability of the
particular coating in question.
Properties
Movement
accommodation factor:
Skinning time:
Cure time:
Service temperature:
Colours:
Siliconized Acrylic Sealant is not recommended for joints
subject to water immersion.
In such cases Nitoseal150
should be considered. Do not apply at temperature below
5oC.
Health and safety
Avoid contact with eye sand skin. In the event of eye
contact, wash thoroughly with clean water.
Storage
At least 12 months shelf life in original unopened cartridges
when stored in dry conditions below 25oC.
10%
Approx.30-60 minutes
(35C/50%RH)
1-3 weeks depending on
climate and thickness
o
Up to 70 C
White and Bronze
Packaging
280 ml cartridges (24 cartridges per carton).
Estimating
Joint preparation
Number of cartridges required =
Joint surfaces must be sound, clean, dry and frost-free.
Excessive dirt, dust, laitance and other contamination must
be removed by wire brushing.
Joint Width (mm) Sealant Depth (mm) X Joint Length (M)
310
A further amount should be allowed for wastage.
Application
Siliconized Acrylic Sealant can be applied by hand or air
operated caulking gun. Ensure that the sealants pushed
firmly into the joint to give complete wetting of the surface.
Any tooling of the sealant surface must be carried out
immediately using a joint shaping tool soaked in white spirit,
or wet sponge. If required, the edges of the joint can be
protected with masking tape. If this is done ensure that the
tape is removed immediately after tooling.
Supply
Contact your local Fosroc office or representative.
Cleaning
Uncured Siliconized Acrylic Sealant can be cleaned off with
water. Cured sealant can be removed mechanically or by
soaking in MEK.
Page 1
Siliconized
Acrylic Sealant
Additional Information
Fosroc manufactures a wide range of complementary
products which include:
Waterproofing membranes & waterstops
Joint sealants & filler boards
Cementitious & epoxy grouts
Specialised flooring materials
Fosroc additionally offers a comprehensive package of
products specifically designed for the repair and
refurbishment of damaged concrete. Fosrocs Systematic
Approach to concrete repair features the following:
Hand-placed repair mortars
Spray grade repair mortars
Fluid micro-concretes
Chemically resistant epoxy mortars
Anti-carbonation/anti-chloride protective coatings
Chemical and abrasion resistant coatings
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous
control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products,
whether or not in accordance with any advice, specification, recommendation of information given by it.
Fosam Company Limited
Head Office
Post Box 11081
Jeddah 21453
Saudi Arabia
www.fosroc.com
Telephone: +966 2 637 5345
Fax: +966 2 637 5891
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Tel: (02) 608 0999
Tel: (02) 665 0187
Tel: (01) 482 9303
Tel: (03) 814 1282
Tel: (07) 250 0469
Fax: (02) 635 3330
Fax: (02) 667 4844
Fax: (01) 482 7562
Fax: (03) 814 1581
Fax: (07) 250 0469
Yanbu
Makkah
Medinah
Jubail
CSD
Tel: (04) 322 4280
Tel: (02) 542 0869
Tel: (04) 845 1767
Tel: (03) 362 3904
Tel: (02) 608 0999
Fax: (04) 391 2980
Fax: (02) 542 0869
Fax: (04) 846 3195
Fax: (03) 362 3875
Fax: (02) 635 3330
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2
FO SA/SILICONIZED ACRYLIC SEALANT/05/A
