APPLICATIONS MANUAL
PEUGEOT IMMOBILISER
CONTENTS
APM107
PAGE
APPLICATIONS
1.1
CONNECTOR LOCATIONS
2.1
GENERAL OPERATION
3.1
SPECIAL FUNCTIONS
4.1
Version 2.0 12/01
APPLICATIONS
VEHICLE
YEAR
SYSTEM
CABLE
106
1997 ON
IMMO 1
ADC110
206
1997 ON
CPH
ADC110
206
1997 ON
BSI
306
1997 ON
IMMO 1
ADC110
306
1997 ON
CPH
ADC110
307
2001 ON
BSI
ADC110
406
97-99
IMMO1
ADC100 + ADC120
NEW 406
99 ON
CPH
ADC110
406 COUPE
97 ON
CPH
ADC110
607
2001 ON
BSI
ADC110
806
1997 ON
CPH
ADC110
EXPERT
1997 ON
CPH
ADC110
PARTNER
1997 ON
IMMO 1
ADC110
PARTNER
1997 ON
BSI
ADC110
RANCH
1997 ON
IMMO 1
ADC110
1.1
CONNECTOR LOCATIONS
206 : ADC110
306 : ADC110
106 : ADC110
2.1
CONNECTOR LOCATIONS
406 : ADC100 + ADC120
NEW 406 : ADC110
307 : ADC110
2.2
GENERAL OPERATION
INTRODUCTION
The Peugeot Immobiliser systems are made up of 3 different types. They all perform various functions, and it is important to understand the basic configuration and the types of
systems fitted.
IMM STANDARD IMMOBILISER
This system was the first transponder system fitted to the Peugeot range of vehicles, after
the keypad system was phased out. The system is a basic electronic control unit which
consists of immobiliser unit, and transponder aerial to pick up the transponder signal
code.
This system is similar to the GM immobiliser system, and is programmed and diagnosed
in much the same way.
CPHPASSENGER COMPARTMENT PROTECTION CONTROL UNIT
The next generation of Immobiliser and alarm system produced the CPH system which
controls a number of additional components which further enhances the vehicle protection system. These include central door locking, ultrasonic passenger sensors to name a
few.
This system is programmed in much the same way, but offers additional functionality on
live data and actuators functions.
BSIBODY SYSTEMS INTERFACE
This is the latest system, and the alarm and immobiliser have now been incorporated into
the body control unit, which controls all body units, including wipers, indicators, lights,
doors, windows, locks, boot, service interval, horn, etc.
Again, with all the BSI because the immobiliser is part of a complicated system there are
many more functions included, on actuators, special functions and live data.
3.1
SPECIAL FUNCTIONS
PROGRAMMING KEYSIMMOBILISER 1 SYSTEM
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
SPECIAL FUNCTIONS
PRESS ENTER KEY
DIAGNOSTIC MENU
PROGRAM KEYS
Select SPECIAL FUNCTIONS from the
Diagnostic Menu using the UP and
DOWN arrows.
Then press the ENTER key.
NOTE : ENSURE ALL DOORS AL
CLOSED WHEN KEY PROGRAMMING IS BEING PERFORMED.
Using the UP and DOWn keys select
the PROGRAM KEYS option
PRESS ENTER KEY
SECURITY CODE
____
To enter the security code use the following procedure :Press
SECURITY CODE
X4YT
to elect Number & Letter
Press
tion
To Erase the previous selec-
Press
To ENTER selection.
Press
To Finish PIN selection.
IS THIS CORRECT
OK=ENTER CLEAR=BACK
WARNING : WHEN PROGRAMMING KEYS, THE SYSTEM AUTOMATICALLY
ERASES THE PLIP KEYS AT THE SAME TIME. BEFORE PROCEEDING WITH
KEY PROGRAMMING, ENSURE YOU HAVE THE PLIP KEY PROGRAMMING
PROCEDURE.
4.1
SPECIAL FUNCTIONS
Contd
INCORRECT ACCESS CODE
If incorrect code is entered the screen
will display as shown.
NOTE : If the code is entered 3 time
incorrectly, then the ECU will lock access for 15 minutes.
PRESS ENTER KEY
PROGRAMMING KEYS
TOTAL KEYS REQUIRED : 2
If Access code is correct, ENTER the
number of keys to program.
NOTE : Max 4 keys can be added.
PRESS ENTER KEY
SWITCH IGNITION ON
IGNITION STATUS OFF
SWITCH IGNITION OFF
IGNITION STATUS ON
4.2
Follow on screen instruction for programming the keys.
After switching IGNTION OFF remove
the key and repeat procedure for additional keys.
SPECIAL FUNCTIONS
PROGRAMMING KEYSBSi MODULE
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
SPECIAL FUNCTIONS
PRESS ENTER KEY
Select SPECIAL FUNCTIONS from the
Diagnostic Menu using the UP and
DOWN arrows.
Then press the ENTER key.
NOTE : ENSURE ALL DOORS AL
CLOSED WHEN KEY PROGRAMMING IS BEING PERFORMED.
DIAGNOSTIC MENU
PROGRAM KEYS
PRESS ENTER KEY
SECURITY CODE
____
SECURITY CODE
X4YT
IS THIS CORRECT
OK=ENTER CLEAR=BACK
Using the UP and DOWn keys select
the PROGRAM KEYS option
To enter the security code use the following procedure :Press
to elect Number & Letter
Press
tion
To Erase the previous selec-
Press
To ENTER selection.
Press
To Finish PIN selection.
NOTE : AFTER PROGRAMMING
CLEAR FAULT CODES AND LOCK
VEHICLE FOR 10 MINUTES BEFORE
TRYING THE KEY OR PLIP.
WARNING : WHEN PROGRAMMING KEYS, THE SYSTEM AUTOMATICALLY
ERASES THE PLIP KEYS AT THE SAME TIME. BEFORE PROCEEDING WITH
KEY PROGRAMMING, ENSURE YOU HAVE THE PLIP KEY PROGRAMMING
PROCEDURE.
4.3
SPECIAL FUNCTIONS
Contd
TRYING TO COMMUNICATE
If Access code is correct, ENTER the
number of keys to program.
NOTE : Max 4 keys can be added.
PRESS ENTER KEY
SWITCH IGNITION OFF
IGNITION STATUS ON
PRESS ENTER KEY
ERASING KEYS
PROGRAMMING KEYS
SWITCH IGNITION ON
SWITCH IGNITION OFF
REMOVE KEY FROM
IGNITION
INSERT NEXT KEY
SWITCH IGNITION ON
IGNITION STATUS OFF
4.4
Follow on screen instruction for programming the keys.
SPECIAL FUNCTIONS
Contd
TRYING TO COMMUNICATE
PRESS ENTER KEY
PRESS BACK TO EXIT
PRESS ENTER TO
PROGRAM NEXT KEY
PRESS ENTER KEY
4.5
NOTE : AFTER PROGRAMMING
CLEAR FAULT CODES AND LOCK
VEHICLE FOR 10 MINUTES BEFORE
TRYING THE KEY OR PLIP.
