ANGUS Technical Data Sheet
AMP
Key Performance
Advantages
Saves formulation cost
Lowers VOC as calculated in
some regions
Improves color development
and adhesion
Requires no process or
equipment changes
2-AMINO-2-METHYL-1-PROPANOL SOLUTION
CAS Registry No. 124-68-5
AMP Multifunctional Amine for Low-Cost
Solvent-Based Alkyd Paint
Lower paint costs and volatile organic compounds (VOC) with AMP (2-amino-2-methyl-1propanol) as the distinct structure and property profile of AMP allows paint formulators
to emulsify up to 15% water into solvent-based alkyd paints with no process or
equipment changes, and no additional raw materials. When following ANGUS product
use guidelines, adding water to your solvent-based paint formulations can save money.
AMP is compatible with most conventional long- and medium-alkyd resins, as well as the
other ingredients in the paint.
Suggested Starting Formulation
Kilograms/ Pounds
Paints and Coatings
Liters/ Gallons
Long or medium oil resin
521.3/ 434.79
White Spirits (Exxsol D40 Equivalent)
158.94/ 132.57
202.4/ 20.24
Rheological Additive (Bentone 1000
Equivalent)
6.05/ 5.04
4.1/ 0.41
547.6/ 54.76
Wetting agent (Anti-Terra U equivalent)
3.57/ 2.98
3.8/ 0.38
10% Calcium octoate
7.35/ 6.13
7.3/ 0.73
Titanium Dioxide
269.36/ 224.64
67.3. 6.73
12% Cobalt octoate
2.11/ 1.80
2.1/ 0.21
18% Zirconium octoate
8.82/ 7.36
8.0/ 0.80
Anti-Skinning Agent (MEKO)
3.32/ 2.77
3.6/ 0.36
AMP-95
1.13/ 0.94
1.2/ 0.12
Water
152.6/ 127.27
152.6/ 15.26
Total
1134.55/ 946.29
1000/ 100
PVC %
~16
Viscosity, Brookfield (100 rpm)
1004 cP
Viscosity, Stormer
83 KU
Gloss, 60
91
We make the best perform better.
angus.com
Resin Types
Dry Film Properties
Most conventional low-viscosity, long- and medium-oil and some
short-oil resins will be suitable in this application. Care should
be taken to evaluate each resin for compatibility with AMP and
water. If in doubt, please consult your resin supplier or local
ANGUS representative. Excellent results have been achieved
with resins with the following properties:
With a little formulation volume optimization, the inclusion of AMP
and water has a minimal impact on gloss. The AMP formulation on
the right of the photo below contains 15% water and has a 12%
raw material cost saving over the control on the left.
Oil type:
Soya (minimal yellowing) Linoleic
Oil content:
65%
Acid number:
6-20 mg KOH
NVM:
70 75%
Control
AMP
Opacity:
It is easy to optimize paint formulations to achieve the same
opacity or covering power.
Material Compatibility
AMP is compatible with most paint raw materials. It should not
cause yellowing or interfere with the oxidative drying process.
Materials should always be checked for potential hydrolysis
issues.
Paint Stability
Solvent-based systems should be stable for at least 24 months.
It is important for paint formulators to carry out stability tests
with their own materials and formulations. Paint containing AMP
Multifunctional Amine and 12.5% water has been proven stable
down to temperatures of -20C/-4F.
Stability after 12 months:
Control
AMP
Improvements to Color Development:
The distinct structure of AMP usually enhances the color
development. AMP Multifunctional Amine is compatible with
numerous types of tinting systems. Additional potential savings
are possible through the more efficient use of tinter.
Control
Control
AMP
AMP
Stability after 50 days @ 50C/122F:
Wood Adhesion:
The distinct structure of AMP allows for the incorporation of
water into the formulation while affording excellent drying
characteristics and beneficial adhesion performance.
DOUBLE COATED
SINGLE COATED
Control
AMP
Control
AMP
Process
Product Stewardship
Make grind with high speed disperser.
ANGUS encourages its customers to review their applications
of ANGUS products from the standpoint of human health and
environmental quality. To help ensure that ANGUS products
are not used in ways for which they are not intended, ANGUS
personnel will assist customers in dealing with environmental
and product safety considerations. For assistance, safety data
sheets or other information, please contact your local ANGUS
representative at the numbers provided in this document.
When considering the use of any ANGUS product in a particular
application, review the latest Safety Data Sheet to ensure that
the intended use is within the scope of approved uses and can be
accomplished safely. Before handling any of the products, obtain
available product safety information including the Safety Data
Sheet(s) and take the necessary steps to ensure safety of use.
Add grind to the let-down and mix well.
Add AMP Multifunctional Amine. Stir for five minutes.
Add water in a controlled manner, preferably into the vortex
of the paint.
Do not stir at high speed. Stirring with low- to mediumhundreds rpm is sufficient. Avoid air entrainment in the paint.
Stir for 2030 minutes after all water has been added.
No off-line process is necessary.
Process and material considerations:
Use long- and medium-oil resins. Check for resin stability
such as yellowing hydrolysis.
AMP must be added before the addition of water.
Add driers in recommended order. Add calcium drier
to the grind.
Extender fillers: calcium carbonate, clays, talc, barium sulfate
can all be used. For matte grades, use either talc or a treated
silica. Untreated silica will destabilize the emulsion.
If a defoamer is required, avoid those containing silicone as
they will destabalize the water emulsion. An example of a
typical non-silicone defoamer is BYK 052.
No in-can preservative (biocide) is required.
Final viscosity adjustment can be made with water (increases
viscosity) or white spirit (decreases viscosity).
Alkyd paint containing AMP and water can be stored in unlined
cans typically used for solvent-based paints; however, it is
important to test the quality of the can before use. In laboratory
tests, no corrosion has been seen in cans after 50 days at
50C/122F.
Contact Information
North America
Western Europe
Middle East and Africa
Greater China
angus.com
Latin America
Central and Eastern Europe
Indian Subcontinent
Japan and Korea
+1 (847) 808-3887
+55 (11) 94245-5307
+33 670654658
+33 670654658
+33 670654658
+33 670654658
+65 8686 5712
Southeast Asia and
New Zealand
+65 8686 5712
+65 8686 5712
Trademark of ANGUS Chemical Company
Notice: No freedom from infringement of any patent owned by ANGUS or others is to be inferred. Because use conditions and applicable laws may differ from one location to another
and may change with time, Customer is responsible for determining whether products and the information in this document are appropriate for Customers use and for ensuring that
Customers workplace and disposal practices are in compliance with applicable laws and other government enactments. The product shown in this literature may not be available for
sale and/or available in all geographies where ANGUS is represented. The claims made may not have been approved for use in all countries. ANGUS assumes no obligation or liability
for the information in the document. References to ANGUS or the Company mean the ANGUS Chemical Company legal entity selling the products to Customer unless expressly
noted. NO WARRANTIES ARE GIVEN: ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.
Published May 2015
Form number: AMP-1891-0415-TCG
